| Age | Commit message (Collapse) | Author |
|---|
|
"LSP" is ZTE's term for this part of the SoC, I suspect it stands for
"low speed peripherals". The main UART is here, together with the flash
controller and more surplus proprietary timers.
It also has one more I2C controller that supposedly connects to a
battery charger, SPI for displays and I2S for analog telephones. The
boards I have don't have any of these components though.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
This clock controller controls high speed devices: CPU, DMA, RAM, SDIO,
Ethernet. The only non-clock, non-reset registers I have spotted here
are hardware spinlocks.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
This register space controls core devices: PLLs, the AHB bus, a lot of
timers, the USB controller, the Cortex M0 processor that boots the board
and a few other devices. For some reason the LTE coprocessor is also
partially controlled by it. The main application processor and DDR
memory are not found here though.
The register to reboot the board is found here, as well as a register to
control whether watchdog expiries cause a board reset.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
This patch adds code to decode and program PLL settings on ZTE's
zx297520v3 SoC. The PLLs on this SoC are usually programmed to static
values by the boot loader. The only situation where .set_rate matters is
dpll, which is not programmed in some cases. The bootloader always sets
fixed rates though: 624 MHz for mpll, 200 for gpll, 480 for upll.
Parsing the bootloader-programmed values allows the clock driver to fill
the clock tree with appropriately clocked parent clocks instead of
registering fixed clocks with hardcoded rates.
I only tested the code on zx297520v3. From looking at the hardcoded PLL
values in the old zx296702 / zx296718 code I believe that these PLLs use
the same encoding, so the code added by this patch should be reusable
and the file has a relatively generic name pll-zx.c.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
This is based on meson/clk-regmap.c, although slightly simplified. I
have kept the copyright lines at the top of the file to indicate its
origin.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
The next patches will implement the regmap clocks and PLL driver. The
actual hardware specific clock listing will live in a separate module.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
|
|
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-3-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190815160020.183334-3-sboyd@kernel.org
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These macros are used by more than one SoC vendor platforms, avoid to
have many copies of these code, this patch moves them to the common
header file which every clock drivers can access to.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
clk_div_table are not supposed to change at runtime. All functions
working with clk_div_table provided by <linux/clk-provider.h> work
with const clk_div_table. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Export I2S mux clocks, so that device tree can refer to them for setting
a better parent clock for I2S work clock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
These should be const.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
It adds zx296718 pll_vga clock for VGA support, so that VGA device can
get required pixel rate from clock driver for different display mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
The bit 0 of PLL_CFG0 register is not powerdown on zx296718, but part of
of postdiv2 field. The consequence is that functions like hw_to_idx()
and zx_pll_enable() will end up tampering the postdiv2 of the PLL.
Let's fix it by defining pd_bit 0xff which is obviously invalid for a
bit position and having PLL driver check the validity before operating
on the bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
To support VOU VGA display driver with different modes, we need to set
flag for a few clocks, so that clk_set_rate() call in VOU driver can get
VGA device desired pixel rate.
While at it, the divider between pll_vga and clk_vga gets corrected, as
it's 1:1 instead of 1:2.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
The i2s related clock support is missing from the existing zx296718
clock driver. This patch adds it, so that the upstream ZX I2S driver
can work out.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The audio related clock support is missing from the existing zx296718
clock driver. Let's add it, so that the upstream ZX SPDIF driver can
work for HDMI audio support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[sboyd@codeaurora.org: Staticize some more structures]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Instead of using panic, we should give an error message and return error
code when of_clk_add_hw_provider() call fails.
Since we have error prompt for failures, the "init over" pr_info output
isn't really necessary but becomes a debug noise. So let's clean it up
along the way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Clock driver should be registered with an earlier initcall than
module_init which is used by most of client device drivers. Otherwise,
probing of these client drivers will likely be deferred due to that
calls into clk API will return -EPROBE_DEFER.
Deferred probing is not a problem for most subsystems, but could bring
some side effect for particular subsystem, like display. On ZX296718
platform, we get Linux logo and boot log lost from display device, just
because the DRM/KMS driver gets -EPROBE_DEFER from devm_clk_get() call.
Let's use core_initcall (qcom and a few other clk drivers use that) for
driver registration to avoid those unnecessary -EPROBE_DEFER and get rid
of the side effect with ZX296718 display system.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The zx296718 clock driver has a creative way of assigning the register
values for each clock, by initializing an __iomem pointer to an
offset and then later adding the base (from ioremap) on top
with a cast to u64. This fail on all 32-bit architectures during
compile testing:
drivers/clk/zte/clk-zx296718.c: In function 'top_clocks_init':
drivers/clk/zte/clk-zx296718.c:554:35: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
zx296718_pll_clk[i].reg_base += (u64)reg_base;
drivers/clk/zte/clk-zx296718.c:579:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/clk/zte/clk-zx296718.c:592:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
It would be nice to avoid all the casts, but I decided to simply
shut up the warnings by changing the type from u64 to uintptr_t,
which does the right thing in practice.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca0233285a93 ("clk: zx: register ZX296718 clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The ZX296718 clocks are statically listed and registered. More
clock will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add power down bit and pll lock bit in pll config structure
to ease new SoC support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This flag is a no-op now. Remove usage of the flag.
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add SPDIF/I2S and GPIO clock for zx296702
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add SPDIF/I2S divider clock method for zx296702
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
It adds a clock driver for zx296702 SoC to register the clock tree to
Common Clock Framework. All the clocks of bus topology and some the
peripheral clocks are ready with this commit. Some missing leaf clocks
for peripherals will be added later when needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
