diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
7 files changed, 127 insertions, 88 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/marvell,sd8787.yaml b/Documentation/devicetree/bindings/net/wireless/marvell,sd8787.yaml index 930b700b73d0..9f905ef5c2c0 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell,sd8787.yaml +++ b/Documentation/devicetree/bindings/net/wireless/marvell,sd8787.yaml @@ -59,6 +59,12 @@ properties: description: Calibration data for sub-band 3 in the 5GHz band. maxItems: 502 + marvell,invalid-reg-hint-in-rom: + $ref: /schemas/types.yaml#/definitions/flag + description: + The regulatory hint in ROM conflicts with platform configuration. + It should be ignored, so the platform regulatory domain can be used. + marvell,wakeup-pin: $ref: /schemas/types.yaml#/definitions/uint32 description: diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml index ae6b97cdc44b..bf4116b057d2 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.yaml @@ -325,22 +325,22 @@ examples: r0 { regdomain = "FCC"; txpower-5g { - b0 { - channels = <36 48>; - rates-ofdm = /bits/ 8 <23 23 23 23 23 23 23 23>; - rates-mcs = /bits/ 8 <1 23 23 23 23 23 23 23 23 23 23>, - /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22>; - rates-ru = /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22 22 22>, - /bits/ 8 <4 20 20 20 20 20 20 20 20 20 20 20 20>; - }; - b1 { - channels = <100 181>; - rates-ofdm = /bits/ 8 <14 14 14 14 14 14 14 14>; - rates-mcs = /bits/ 8 <4 14 14 14 14 14 14 14 14 14 14>; - txs-delta = <12 9 6>; - rates-ru = /bits/ 8 <7 14 14 14 14 14 14 14 14 14 14 14 14>; - }; - }; + b0 { + channels = <36 48>; + rates-ofdm = /bits/ 8 <23 23 23 23 23 23 23 23>; + rates-mcs = /bits/ 8 <1 23 23 23 23 23 23 23 23 23 23>, + /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22>; + rates-ru = /bits/ 8 <3 22 22 22 22 22 22 22 22 22 22 22 22>, + /bits/ 8 <4 20 20 20 20 20 20 20 20 20 20 20 20>; + }; + b1 { + channels = <100 181>; + rates-ofdm = /bits/ 8 <14 14 14 14 14 14 14 14>; + rates-mcs = /bits/ 8 <4 14 14 14 14 14 14 14 14 14 14>; + txs-delta = <12 9 6>; + rates-ru = /bits/ 8 <7 14 14 14 14 14 14 14 14 14 14 14 14>; + }; + }; }; }; }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml index e667d78b3ab3..0cb065265df4 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml @@ -92,6 +92,22 @@ properties: ieee80211-freq-limit: true + nvmem-cells: + minItems: 1 + maxItems: 3 + description: + References to nvmem cells for MAC address and/or calibration data. + Supported cell names are mac-address, calibration, and pre-calibration. + + nvmem-cell-names: + minItems: 1 + maxItems: 3 + items: + enum: + - mac-address + - calibration + - pre-calibration + qcom,calibration-data: $ref: /schemas/types.yaml#/definitions/uint8-array description: @@ -408,4 +424,4 @@ examples: "msi15", "legacy"; ieee80211-freq-limit = <5470000 5875000>; - }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath12k-wsi.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath12k-wsi.yaml index 589960144fe1..fa64c8aa56f5 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath12k-wsi.yaml +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath12k-wsi.yaml @@ -58,13 +58,6 @@ properties: String to uniquely identify variant of the calibration data for designs with colliding bus and device ids - qcom,ath12k-calibration-variant: - $ref: /schemas/types.yaml#/definitions/string - deprecated: true - description: - String to uniquely identify variant of the calibration data for designs - with colliding bus and device ids - qcom,wsi-controller: $ref: /schemas/types.yaml#/definitions/flag description: diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml index 6c0888ae4c4e..60dfe257eadc 100644 --- a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml @@ -50,6 +50,9 @@ properties: used, this property is required. When SDIO is used, the "in-band" interrupt provided by the SDIO bus is used unless an interrupt is defined in the Device Tree. + + The hardware suffers from a limitation when this property is used with + SDIO. OOB IRQ with SDIO should only be used for debug. maxItems: 1 reset-gpios: diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt deleted file mode 100644 index 88fd28d15eac..000000000000 --- a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt +++ /dev/null @@ -1,64 +0,0 @@ -* Texas Instruments wl1251 wireless lan controller - -The wl1251 chip can be connected via SPI or via SDIO. This -document describes the binding for the SPI connected chip. - -Required properties: -- compatible : Should be "ti,wl1251" -- reg : Chip select address of device -- spi-max-frequency : Maximum SPI clocking speed of device in Hz -- interrupts : Should contain interrupt line -- vio-supply : phandle to regulator providing VIO - -Optional properties: -- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which - provides configuration data (calibration, MAC, ...) -- ti,power-gpio : GPIO connected to chip's PMEN pin if operated in - SPI mode -- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt - for optional SPI connection related properties, - -Examples: - -&spi1 { - wl1251@0 { - compatible = "ti,wl1251"; - - reg = <0>; - spi-max-frequency = <48000000>; - spi-cpol; - spi-cpha; - - interrupt-parent = <&gpio2>; - interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ - - vio-supply = <&vio>; - ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ - }; -}; - -&mmc3 { - vmmc-supply = <&wlan_en>; - - bus-width = <4>; - non-removable; - ti,non-removable; - cap-power-off-card; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pins>; - - #address-cells = <1>; - #size-cells = <0>; - - wlan: wifi@1 { - compatible = "ti,wl1251"; - - reg = <1>; - - interrupt-parent = <&gpio1>; - interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ - - ti,wl1251-has-eeprom; - }; -}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.yaml b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.yaml new file mode 100644 index 000000000000..6ce82c4a2c0b --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/ti,wl1251.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments WL1251 Wireless LAN Controller + +maintainers: + - Eduard Bostina <egbostina@gmail.com> + +properties: + compatible: + const: ti,wl1251 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vio-supply: + description: + Phandle to the regulator providing VIO. Required when connected via SPI. + + ti,power-gpio: + maxItems: 1 + description: + GPIO connected to chip's PMEN pin if operated in SPI mode. + + ti,wl1251-has-eeprom: + type: boolean + description: + The wl1251 has an EEPROM connected, which provides configuration + data (calibration, MAC, ...). + + clocks: + maxItems: 1 + + spi-max-frequency: true + spi-cpol: true + spi-cpha: true + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + wifi@0 { + compatible = "ti,wl1251"; + reg = <0>; + spi-max-frequency = <48000000>; + spi-cpol; + spi-cpha; + interrupt-parent = <&gpio2>; + interrupts = <10 IRQ_TYPE_NONE>; + vio-supply = <&vio>; + ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + mmc { + #address-cells = <1>; + #size-cells = <0>; + wifi@1 { + compatible = "ti,wl1251"; + reg = <1>; + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + ti,wl1251-has-eeprom; + }; + }; |