#ifndef _RAID1_H
#define _RAID1_H
struct mirror_info {
struct md_rdev *rdev;
sector_t head_position;
};
/*
* memory pools need a pointer to the mddev, so they can force an unplug
* when memory is tight, and a count of the number of drives that the
* pool was allocated for, so they know how much to allocate and free.
* mddev->raid_disks cannot be used, as it can change while a pool is active
* These two datums are stored in a kmalloced struct.
*/
struct pool_info {
struct mddev *mddev;
int raid_disks;
};
struct r1_private_data_s {
struct mddev *mddev;
struct mirror_info *mirrors;
int raid_disks;
/* When choose the best device for a read (read_balance())
* we try to keep sequential reads one the same device
* using 'last_used' and 'next_seq_sect'
*/
int last_used;
sector_t next_seq_sect;
/* During resync, read_balancing is only allowed on the part
* of the array that has been resynced. 'next_resync' tells us
* where that is.
*/
sector_t next_resync;
spinlock_t device_lock;
/* list of 'struct r1bio' that need to be processed by raid1d,
* whether to retry a read, writeout a resync or recovery
* block, or anything else.
*/
struct list_head retry_list;
/* queue pending writes to be submitted on unplug */
struct bio_list pending_bio_list;
/* for use when syncing mirrors:
* We don't allow both normal IO and resync/recovery IO at
* the same time - resync/recovery can only happen when there
* is no other IO. So when either is active, the other has to wait.
* See more details description in raid1.c near raise_barrier().
*/
wait_queue_head_t wait_barrier;
spinlock_t resync_lock;
int nr_pending;
int nr_waiting;
int nr_queued;
int barrier;
/* Set to 1 if a full sync is needed, (fresh device added).
* Cleared when a sync completes.
*/
int fullsync;
/* When the same as mddev->recovery_disabled we don't allow
* recovery to be attempted as we expect a read error.
*/
int recovery_disabled;
/* poolinfo contains information about the content of the
* mempools - it changes when the array grows or shrinks
*/
struct pool_info *poolinfo;
mempool_t *r1bio_pool;
mempool_t *r1buf_pool;
/* temporary buffer to synchronous IO when attempting to repair
* a read error.
*/
struct page *tmppage;
/* When taking over an array from a different personality, we store
* the new thread here until we fully activate the array.
*/
struct md_thread *thread;
};
typedef struct r1_private_data_s conf_t;
/*
* this is our 'private' RAID1 bio.
*
* it contains information about what kind of IO operations were started
* for this RAID1 operation, and about their status:
*/
struct r1bio {
atomic_t remaining; /* 'have we finished' count,
* used from IRQ handlers
*/
atomic_t behind_remaining; /* number of write-behind ios remaining
* in this BehindIO request
*/
sector_t sector;
int sectors;
unsigned long state;
struct mddev *mddev;
/*
* original bio going to /dev/mdx
*/
struct bio *master_bio;
/*
* if the IO is in READ direction, then this is where we read
*/
int read_disk;
struct list_head retry_list;
/* Next two are only valid when R1BIO_BehindIO is set */
struct bio_vec *behind_bvecs;
int behind_page_count;
/*
* if the IO is in WRITE direction, then multiple bios are used.
* We choose the number when they are allocated.
*/
struct bio *bios[0];
/* DO NOT PUT ANY NEW FIELDS HERE - bios array is contiguously alloced*/
};
/* when we get a read error on a read-only array, we redirect to another
* device without failing the first device, or trying to over-write to
* correct the read error. To keep track of bad blocks on a per-bio
* level, we store IO_BLOCKED in the appropriate 'bios' pointer
*/
#define IO_BLOCKED ((struct bio *)1)
/* When we successfully write to a known bad-block, we need to remove the
* bad-block marking which must be done from process context. So we record
* the success by setting bios[n] to IO_MADE_GOOD
*/
#define IO_MADE_GOOD ((struct bio *)2)
#define BIO_SPECIAL(bio) ((unsigned long)bio <= 2)
/* bits for r1bio.state */
#define R1BIO_Uptodate 0
#define R1BIO_IsSync 1
#define R1BIO_Degraded 2
#define R1BIO_BehindIO 3
/* Set ReadError on bios that experience a readerror so that
* raid1d knows what to do with them.
*/
#define R1BIO_ReadError 4
/* For write-behind requests, we call bi_end_io when
* the last non-write-behind device completes, providing
* any write was successful. Otherwise we call when
* any write-behind write succeeds, otherwise we call
* with failure when last write completes (and all failed).
* Record that bi_end_io was called with this flag...
*/
#define R1BIO_Returned 6
/* If a write for this request means we can clear some
* known-bad-block records, we set this flag
*/
#define R1BIO_MadeGood 7
#define R1BIO_WriteError 8
extern int md_raid1_congested(struct mddev *mddev, int bits);
#endif
