// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Google Cheza device tree source (common between revisions)
*
* Copyright 2018 Google LLC.
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sdm845.dtsi"
/* PMICs depend on spmi_bus label and so must come after SoC */
#include "pm8005.dtsi"
#include "pm8998.dtsi"
/ {
aliases {
bluetooth0 = &bluetooth;
serial1 = &uart6;
serial0 = &uart9;
wifi0 = &wifi;
};
chosen {
stdout-path = "serial0:115200n8";
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&cros_ec_pwm 0>;
enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
power-supply = <&ppvar_sys>;
pinctrl-names = "default";
pinctrl-0 = <&ap_edp_bklten>;
};
/* FIXED REGULATORS - parents above children */
/* This is the top level supply and variable voltage */
ppvar_sys: ppvar-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "ppvar_sys";
regulator-always-on;
regulator-boot-on;
};
/* This divides ppvar_sys by 2, so voltage is variable */
src_vph_pwr: src-vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "src_vph_pwr";
/* EC turns on with switchcap_on_l; always on for AP */
regulator-always-on;
regulator-boot-on;
vin-supply = <&ppvar_sys>;
};
pp5000_a: pp5000-a-regulator {
compatible = "regulator-fixed";
regulator-name = "pp5000_a";
/* EC turns on with en_pp5000_a; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&ppvar_sys>;
};
src_vreg_bob: src-vreg-bob-regulator {
compatible = "regulator-fixed";
regulator-name = "src_vreg_bob";
/* EC turns on with vbob_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3600000>;
regulator-max-microvolt = <3600000>;
vin-supply = <&ppvar_sys>;
};
pp3300_dx_edp: pp3300-dx-edp-regulator {
compatible = "regulator-fixed";
regulator-name = "pp3300_dx_edp";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&en_pp3300_dx_edp>;
};
/*
* Apparently RPMh does not provide support for PM8998 S4 because it
* is always-on; model it as a fixed regulator.
*/
src_pp1800_s4a: pm8998-smps4 {
compatible = "regulator-fixed";
regulator-name = "src_pp1800_s4a";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&src_vph_pwr>;
};
/* BOARD-SPECIFIC TOP LEVEL NODES */
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pen_eject_odl>;
switch-pen-insert {
label = "Pen Insert";
/* Insert = low, eject = high */
gpios = <&tlmm 119 GPIO_ACTIVE_LOW>;
linux,code = <SW_PEN_INSERTED>;
linux,input-type = <EV_SW>;
wakeup-source;
};
};
panel: panel {
compatible = "innolux,p120zdg-bf1";
power-supply = <&pp3300_dx_edp>;
backlight = <&backlight>;
no-hpd;
ports {
panel_in: port {
panel_in_edp: endpoint {
remote-endpoint = <&sn65dsi86_out>;
};
};
};
};
};
&psci {
/delete-node/ cpu0;
/delete-node/ cpu1;
/delete-node/ cpu2;
/delete-node/ cpu3;
/delete-node/ cpu4;
/delete-node/ cpu5;
/delete-node/ cpu6;
/delete-node/ cpu7;
/delete-node/ cpu-cluster0;
};
&cpus {
/delete-node/ domain-idle-states;
};
&cpu_idle_states {
LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
compatible = "arm,idle-state";
idle-state-name = "little-power-down";
arm,psci-suspend-param = <0x40000003>;
entry-latency-us = <350>;
exit-latency-us = <461>;
min-residency-us = <1890>;
local-timer-stop;
};
LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
compatible = "arm,idle-state";
idle-state-name = "little-rail-power-down";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <360>;
exit-latency-us = <531>;
min-residency-us = <3934>;
local-timer-stop;
};
BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
compatible = "arm,idle-state";
idle-state-name = "big-power-down";
arm,psci-suspend-param = <0x40000003>;
entry-latency-us = <264>;
exit-latency-us = <621>;
min-residency-us = <952>;
local-timer-stop;
};
BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
compatible = "arm,idle-state";
idle-state-name = "big-rail-power-down";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <702>;
exit-latency-us = <1061>;
min-residency-us = <4488>;
local-timer-stop;
};
CLUSTER_SLEEP_0: cluster-sleep-0 {
compatible = "arm,idle-state";
idle-state-name = "cluster-power-down";
arm,psci-suspend-param = <0x400000F4>;
entry-latency-us = <3263>;
exit-latency-us = <6562>;
min-residency-us = <9987>;
local-timer-stop;
};
};
&CPU0 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&LITTLE_CPU_SLEEP_0
&LITTLE_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU1 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&LITTLE_CPU_SLEEP_0
&LITTLE_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU2 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&LITTLE_CPU_SLEEP_0
&LITTLE_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU3 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&LITTLE_CPU_SLEEP_0
&LITTLE_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU4 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&BIG_CPU_SLEEP_0
&BIG_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU5 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&BIG_CPU_SLEEP_0
&BIG_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU6 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&BIG_CPU_SLEEP_0
&BIG_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
&CPU7 {
/delete-property/ power-domains;
/delete-property/ power-domain-names;
cpu-idle-states = <&BIG_CPU_SLEEP_0
&BIG_CPU_SLEEP_1
&CLUSTER_SLEEP_0>;
};
/*
* Reserved memory changes
*
* Putting this all together (out of order with the rest of the file) to keep
* all modifications to the memory map (from sdm845.dtsi) in one place.
*/
/*
* Our mpss_region is 8MB bigger than the default one and that conflicts
* with venus_mem and cdsp_mem.
*
* For venus_mem we'll delete and re-create at a different address.
*
* cdsp_mem isn't used on cheza right now so we won't bother re-creating it; but
* that also means we need to delete cdsp_pas.
*/
/delete-node/ &venus_mem;
/delete-node/ &cdsp_mem;
/delete-node/ &cdsp_pas;
/delete-node/ &gpu_mem;
/* Increase the size from 120 MB to 128 MB */
&mpss_region {
reg = <0 0x8e000000 0 0x8000000>;
};
/* Increase the size from 2MB to 8MB */
&rmtfs_mem {
reg = <0 0x88f00000 0 0x800000>;
};
/ {
reserved-memory {
venus_mem: memory@96000000 {
reg = <0 0x96000000 0 0x500000>;
no-map;
};
};
};
&qspi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
/*
* In theory chip supports up to 104 MHz and controller up
* to 80 MHz, but above 25 MHz wasn't reliable so we'll use
* that for now. b:117440651
*/
spi-max-frequency = <25000000>;
spi-tx-bus-width = <2>;
spi-rx-bus-width = <2>;
};
};
&apps_rsc {
pm8998-rpmh-regulators {
compatible = "qcom,pm8998-rpmh-regulators";
qcom,pmic-id = "a";
vdd-s1-supply = <&src_vph_pwr>;
vdd-s2-supply = <&src_vph_pwr>;
vdd-s3-supply = <&src_vph_pwr>;
vdd-s4-supply = <&src_vph_pwr>;
vdd-s5-supply = <&src_vph_pwr>;
vdd-s6-supply = <&src_vph_pwr>;
vdd-s7-supply = <&src_vph_pwr>;
vdd-s8-supply = <&src_vph_pwr>;
vdd-s9-supply = <&src_vph_pwr>;
vdd-s10-supply = <&src_vph_pwr>;
vdd-s11-supply = <&src_vph_pwr>;
vdd-s12-supply = <&src_vph_pwr>;
vdd-s13-supply = <&src_vph_pwr>;
vdd-l1-l27-supply = <&src_pp1025_s7a>;
vdd-l2-l8-l17-supply = <&src_pp1350_s3a>;
vdd-l3-l11-supply = <&src_pp1025_s7a>;
vdd-l4-l5-supply = <&src_pp1025_s7a>;
vdd-l6-supply = <&src_vph_pwr>;
vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>;
vdd-l9-supply = <&src_pp2040_s5a>;
vdd-l10-l23-l25-supply = <&src_vreg_bob>;
vdd-l13-l19-l21-supply = <&src_vreg_bob>;
vdd-l16-l28-supply = <&src_vreg_bob>;
vdd-l18-l22-supply = <&src_vreg_bob>;
vdd-l20-l24-supply = <&src_vreg_bob>;
vdd-l26-supply = <&src_pp1350_s3a>;
vin-lvs-1-2-supply = <&src_pp1800_s4a>;
src_pp1125_s2a: smps2 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
src_pp1350_s3a: smps3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
src_pp2040_s5a: smps5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
src_pp1025_s7a: smps7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vdd_qusb_hs0:
vdda_hp_pcie_core:
vdda_mipi_csi0_0p9:
vdda_mipi_csi1_0p9:
vdda_mipi_csi2_0p9:
vdda_mipi_dsi0_pll:
vdda_mipi_dsi1_pll:
vdda_qlink_lv:
vdda_qlink_lv_ck:
vdda_qrefs_0p875:
vdda_pcie_core:
vdda_pll_cc_ebi01:
vdda_pll_cc_ebi23:
vdda_sp_sensor:
vdda_ufs1_core:
vdda_ufs2_core:
vdda_usb1_ss_core:
vdda_usb2_ss_core:
src_pp875_l1a: ldo1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_10:
src_pp1200_l2a: ldo2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
/* TODO: why??? */
regulator-always-on;
};
pp1000_l3a_sdr845: ldo3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdd_wcss_cx:
vdd_wcss_mx:
vdda_wcss_pll:
src_pp800_l5a: ldo5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_13:
src_pp1800_l6a: ldo6 {
regulator-min-microvolt = <1856000>;
regulator-max-microvolt = <1856000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp1800_l7a_wcn3990: ldo7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1200_l8a: ldo8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1248000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp1800_dx_pen:
src_pp1800_l9a: ldo9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1800_l10a: ldo10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp1000_l11a_sdr845: ldo11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1048000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdd_qfprom:
vdd_qfprom_sp:
vdda_apc1_cs_1p8:
vdda_gfx_cs_1p8:
vdda_qrefs_1p8:
vdda_qusb_hs0_1p8:
vddpx_11:
src_pp1800_l12a: ldo12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_2:
src_pp2950_l13a: ldo13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1800_l14a: ldo14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1800_l15a: ldo15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp2700_l16a: ldo16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1300_l17a: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp2700_l18a: ldo18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
/*
* NOTE: this rail should have been called
* src_pp3300_l19a in the schematic
*/
src_pp3000_l19a: ldo19 {
regulator-min-microvolt = <3304000>;
regulator-max-microvolt = <3304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp2950_l20a: ldo20 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp2950_l21a: ldo21 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp3300_hub:
src_pp3300_l22a: ldo22 {
regulator-min-microvolt = <3304000>;
regulator-max-microvolt = <3304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
/*
* HACK: Should add a usb hub node and driver
* to turn this on and off at suspend/resume time
*/
regulator-boot-on;
regulator-always-on;
};
pp3300_l23a_ch1_wcn3990: ldo23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdda_qusb_hs0_3p1:
src_pp3075_l24a: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp3300_l25a_ch0_wcn3990: ldo25 {
regulator-min-microvolt = <3304000>;
regulator-max-microvolt = <3304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp1200_hub:
vdda_hp_pcie_1p2:
vdda_hv_ebi0:
vdda_hv_ebi1:
vdda_hv_ebi2:
vdda_hv_ebi3:
vdda_mipi_csi_1p25:
vdda_mipi_dsi0_1p2:
vdda_mipi_dsi1_1p2:
vdda_pcie_1p2:
vdda_ufs1_1p2:
vdda_ufs2_1p2:
vdda_usb1_ss_1p2:
vdda_usb2_ss_1p2:
src_pp1200_l26a: ldo26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
pp3300_dx_pen:
src_pp3300_l28a: ldo28 {
regulator-min-microvolt = <3304000>;
regulator-max-microvolt = <3304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
src_pp1800_lvs1: lvs1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
src_pp1800_lvs2: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
pm8005-rpmh-regulators {
compatible = "qcom,pm8005-rpmh-regulators";
qcom,pmic-id = "c";
vdd-s1-supply = <&src_vph_pwr>;
vdd-s2-supply = <&src_vph_pwr>;
vdd-s3-supply = <&src_vph_pwr>;
vdd-s4-supply = <&src_vph_pwr>;
src_pp600_s3c: smps3 {
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <600000>;
};
};
};
&dsi0 {
status = "okay";
vdda-supply = <&vdda_mipi_dsi0_1p2>;
ports {
port@1 {
endpoint {
remote-endpoint = <&sn65dsi86_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
&dsi0_phy {
status = "okay";
vdds-supply = <&vdda_mipi_dsi0_pll>;
};
edp_brij_i2c: &i2c3 {
status = "okay";
clock-frequency = <400000>;
sn65dsi86_bridge: bridge@2d {
compatible = "ti,sn65dsi86";
reg = <0x2d>;
pinctrl-names = "default";
pinctrl-0 = <&edp_brij_en &edp_brij_irq>;
interrupt-parent = <&tlmm>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
vpll-supply = <&src_pp1800_s4a>;
vccio-supply = <&src_pp1800_s4a>;
vcca-supply = <&src_pp1200_l2a>;
vcc-supply = <&src_pp1200_l2a>;
clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
clock-names = "refclk";
no-hpd;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
sn65dsi86_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
port@1 {
reg = <1>;
sn65dsi86_out: endpoint {
remote-endpoint = <&panel_in_edp>;
};
};
};
};
};
ap_pen_1v8: &i2c11 {
status = "okay";
clock-frequency = <400000>;
digitizer@9 {
compatible = "wacom,w9013", "hid-over-i2c";
reg = <0x9>;
pinctrl-names = "default";
pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>;
vdd-supply = <&pp3300_dx_pen>;
vddl-supply = <&pp1800_dx_pen>;
post-power-on-delay-ms = <100>;
interrupt-parent = <&tlmm>;
interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
hid-descr-addr = <0x1>;
};
};
amp_i2c: &i2c12 {
status = "okay";
clock-frequency = <400000>;
};
ap_ts_i2c: &i2c14 {
status = "okay";
clock-frequency = <400000>;
touchscreen@10 {
compatible = "elan,ekth3500";
reg = <0x10>;
pinctrl-names = "default";
pinctrl-0 = <&ts_int_l &ts_reset_l>;
interrupt-parent = <&tlmm>;
interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
vcc33-supply = <&src_pp3300_l28a>;
reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
};
};
&gmu {
status = "okay";
};
&gpu {
status = "okay";
};
&ipa {
status = "okay";
modem-init;
};
&lpasscc {
status = "okay";
};
&mdss {
status = "okay";
};
/*
* Cheza fw does not properly program the GPU aperture to allow the
* GPU to update the SMMU pagetables for context switches. Work
* around this by dropping the "qcom,adreno-smmu" compat string.
*/
&adreno_smmu {
compatible = "qcom,sdm845-smmu-v2", "qcom,smmu-v2";
};
&mss_pil {
status = "okay";
iommus = <&apps_smmu 0x781 0x0>,
<&apps_smmu 0x724 0x3>;
};
&pm8998_pwrkey {
status = "disabled";
};
&qupv3_id_0 {
status = "okay";
iommus = <&apps_smmu 0x0 0x3>;
};
&qupv3_id_1 {
status = "okay";
iommus = <&apps_smmu 0x6c0 0x3>;
};
&sdhc_2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>;
vmmc-supply = <&src_pp2950_l21a>;
vqmmc-supply = <&vddpx_2>;
cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
};
&spi0 {
status = "okay";
};
&spi5 {
status = "okay";
tpm@0 {
compatible = "google,cr50";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&h1_ap_int_odl>;
spi-max-frequency = <800000>;
interrupt-parent = <&tlmm>;
interrupts = <129 IRQ_TYPE_EDGE_RISING>;
};
};
&spi10 {
status = "okay";
cros_ec: ec@0 {
compatible = "google,cros-ec-spi";
reg = <0>;
interrupt-parent = <&tlmm>;
interrupts = <122 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&ec_ap_int_l>;
spi-max-frequency = <3000000>;
cros_ec_pwm: pwm {
compatible = "google,cros-ec-pwm";
#pwm-cells = <1>;
};
i2c_tunnel: i2c-tunnel {
compatible = "google,cros-ec-i2c-tunnel";
google,remote-bus = <0>;
#address-cells = <1>;
#size-cells = <0>;
};
};
};
#include <arm/cros-ec-keyboard.dtsi>
#include <arm/cros-ec-sbs.dtsi>
&uart6 {
status = "okay";
pinctrl-0 = <&qup_uart6_4pin>;
bluetooth: wcn3990-bt {
compatible = "qcom,wcn3990-bt";
vddio-supply = <&src_pp1800_s4a>;
vddxo-supply = <&pp1800_l7a_wcn3990>;
vddrf-supply = <&src_pp1300_l17a>;
vddch0-supply = <&pp3300_l25a_ch0_wcn3990>;
max-speed = <3200000>;
};
};
&uart9 {
status = "okay";
};
&ufs_mem_hc {
status = "okay";
reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
vcc-supply = <&src_pp2950_l20a>;
vcc-max-microamp = <600000>;
};
&ufs_mem_phy {
status = "okay";
vdda-phy-supply = <&vdda_ufs1_core>;
vdda-pll-supply = <&vdda_ufs1_1p2>;
};
&usb_1 {
status = "okay";
/* We'll use this as USB 2.0 only */
qcom,select-utmi-as-pipe-clk;
};
&usb_1_dwc3 {
/*
* The hardware design intends this port to be hooked up in peripheral
* mode, so we'll hardcode it here. Some details:
* - SDM845 expects only a single Type C connector so it has only one
* native Type C port but cheza has two Type C connectors.
* - The only source of DP is the single native Type C port.
* - On cheza we want to be able to hook DP up to _either_ of the
* two Type C connectors and want to be able to achieve 4 lanes of DP.
* - When you configure a Type C port for 4 lanes of DP you lose USB3.
* - In order to make everything work, the native Type C port is always
* configured as 4-lanes DP so it's always available.
* - The extra USB3 port on SDM845 goes to a USB 3 hub which is then
* sent to the two Type C connectors.
* - The extra USB2 lines from the native Type C port are always
* setup as "peripheral" so that we can mux them over to one connector
* or the other if someone needs the connector configured as a gadget
* (but they only get USB2 speeds).
*
* All the hardware muxes would allow us to hook things up in different
* ways to some potential benefit for static configurations (you could
* achieve extra USB2 bandwidth by using two different ports for the
* two connectors or possibly even get USB3 peripheral mode), but in
* each case you end up forcing to disconnect/reconnect an in-use
* USB session in some cases depending on what you hotplug into the
* other connector. Thus hardcoding this as peripheral makes sense.
*/
dr_mode = "peripheral";
/*
* We always need the high speed pins as 4-lanes DP in case someone
* hotplugs a DP peripheral. Thus limit this port to a max of high
* speed.
*/
maximum-speed = "high-speed";
/*
* We don't need the usb3-phy since we run in highspeed mode always, so
* re-define these properties removing the superspeed USB PHY reference.
*/
phys = <&usb_1_hsphy>;
phy-names = "usb2-phy";
};
&usb_1_hsphy {
status = "okay";
vdd-supply = <&vdda_usb1_ss_core>;
vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
};
&usb_2 {
status = "okay";
};
&usb_2_dwc3 {
/* We have this hooked up to a hub and we always use in host mode */
dr_mode = "host";
};
&usb_2_hsphy {
status = "okay";
vdd-supply = <&vdda_usb2_ss_core>;
vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
};
&usb_2_qmpphy {
status = "okay";
vdda-phy-supply = <&vdda_usb2_ss_1p2>;
vdda-pll-supply = <&vdda_usb2_ss_core>;
};
&wifi {
status = "okay";
vdd-0.8-cx-mx-supply = <&src_pp800_l5a >;
vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>;
vdd-1.3-rfa-supply = <&src_pp1300_l17a>;
vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>;
};
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qspi_cs0 {
bias-disable;
};
&qspi_clk {
bias-disable;
};
&qspi_data01 {
/* High-Z when no transfers; nice to park the lines */
bias-pull-up;
};
&qup_i2c3_default {
drive-strength = <2>;
/* Has external pullup */
bias-disable;
};
&qup_i2c11_default {
drive-strength = <2>;
/* Has external pullup */
bias-disable;
};
&qup_i2c12_default {
drive-strength = <2>;
/* Has external pullup */
bias-disable;
};
&qup_i2c14_default {
drive-strength = <2>;
/* Has external pullup */
bias-disable;
};
&qup_spi0_default {
drive-strength = <2>;
bias-disable;
};
&qup_spi5_default {
drive-strength = <2>;
bias-disable;
};
&qup_spi10_default {
drive-strength = <2>;
bias-disable;
};
&qup_uart9_rx {
drive-strength = <2>;
bias-pull-up;
};
&qup_uart9_tx {
drive-strength = <2>;
bias-disable;
};
/* PINCTRL - board-specific pinctrl */
&pm8005_gpios {
gpio-line-names = "",
"",
"SLB",
"";
};
&pm8998_adc {
adc-chan@4d {
reg = <ADC5_AMUX_THM1_100K_PU>;
label = "sdm_temp";
};
adc-chan@4e {
reg = <ADC5_AMUX_THM2_100K_PU>;
label = "quiet_temp";
};
adc-chan@4f {
reg = <ADC5_AMUX_THM3_100K_PU>;
label = "lte_temp_1";
};
adc-chan@50 {
reg = <ADC5_AMUX_THM4_100K_PU>;
label = "lte_temp_2";
};
adc-chan@51 {
reg = <ADC5_AMUX_THM5_100K_PU>;
label = "charger_temp";
};
};
&pm8998_gpios {
gpio-line-names = "",
"",
"SW_CTRL",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"",
"CFG_OPT1",
"WCSS_PWR_REQ",
"",
"CFG_OPT2",
"SLB";
};
&tlmm {
/*
* pinctrl settings for pins that have no real owners.
*/
pinctrl-names = "default", "sleep";
pinctrl-0 = <&bios_flash_wp_r_l>,
<&ap_suspend_l_deassert>;
pinctrl-1 = <&bios_flash_wp_r_l>,
<&ap_suspend_l_assert>;
/*
* Hogs prevent usermode from changing the value. A GPIO can be both
* here and in the pinctrl section.
*/
ap-suspend-l-hog {
gpio-hog;
gpios = <126 GPIO_ACTIVE_LOW>;
output-low;
};
ap_edp_bklten: ap-edp-bklten-state {
pins = "gpio37";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
bios_flash_wp_r_l: bios-flash-wp-r-l-state {
pins = "gpio128";
function = "gpio";
input-enable;
bias-disable;
};
ec_ap_int_l: ec-ap-int-l-state {
pins = "gpio122";
function = "gpio";
input-enable;
bias-pull-up;
};
edp_brij_en: edp-brij-en-state {
pins = "gpio102";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
edp_brij_irq: edp-brij-irq-state {
pins = "gpio10";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
en_pp3300_dx_edp: en-pp3300-dx-edp-state {
pins = "gpio43";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
h1_ap_int_odl: h1-ap-int-odl-state {
pins = "gpio129";
function = "gpio";
input-enable;
bias-pull-up;
};
pen_eject_odl: pen-eject-odl-state {
pins = "gpio119";
function = "gpio";
bias-pull-up;
};
pen_irq_l: pen-irq-l-state {
pins = "gpio24";
function = "gpio";
/* Has external pullup */
bias-disable;
};
pen_pdct_l: pen-pdct-l-state {
pins = "gpio63";
function = "gpio";
/* Has external pullup */
bias-disable;
};
pen_rst_l: pen-rst-l-state {
pins = "gpio23";
function = "gpio";
bias-disable;
drive-strength = <2>;
/*
* The pen driver doesn't currently support
* driving this reset line. By specifying
* output-high here we're relying on the fact
* that this pin has a default pulldown at boot
* (which makes sure the pen was in reset if it
* was powered) and then we set it high here to
* take it out of reset. Better would be if the
* pen driver could control this and we could
* remove "output-high" here.
*/
output-high;
};
sdc2_clk: sdc2-clk-state {
pins = "sdc2_clk";
bias-disable;
/*
* It seems that mmc_test reports errors if drive
* strength is not 16.
*/
drive-strength = <16>;
};
sdc2_cmd: sdc2-cmd-state {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <16>;
};
sdc2_data: sdc2-data-state {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <16>;
};
sd_cd_odl: sd-cd-odl-state {
pins = "gpio44";
function = "gpio";
bias-pull-up;
};
ts_int_l: ts-int-l-state {
pins = "gpio125";
function = "gpio";
bias-pull-up;
};
ts_reset_l: ts-reset-l-state {
pins = "gpio118";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
ap_suspend_l_assert: ap-suspend-l-assert-state {
pins = "gpio126";
function = "gpio";
bias-disable;
drive-strength = <2>;
output-low;
};
ap_suspend_l_deassert: ap-suspend-l-deassert-state {
pins = "gpio126";
function = "gpio";
bias-disable;
drive-strength = <2>;
output-high;
};
};
&venus {
status = "okay";
video-firmware {
iommus = <&apps_smmu 0x10b2 0x0>;
};
};
