| Age | Commit message (Collapse) | Author |
|---|
|
Fix misspellings in comments across the MFD drivers and headers, found
with scripts/checkpatch.pl using the list in scripts/spelling.txt.
Only touches comments, no code changes.
Signed-off-by: Hemanth Selam <hemanth.selam@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260924103046.1709181-1-hemanth.selam@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
S2MU005's interrupt registers divided into three domains, each for the
charger, flash LEDs, and the MUIC, packed into a single regmap IRQ chip
construct.
In devices other than S2MPG1X, the revision can be retrieved from the
first register of the PMIC regmap. In S2MU005 however, the location is
in offset 0x73. Introduce a switch-case block to allow selecting the
REG_ID register. S2MU005 also has a field mask for the revision. Apply
it using FIELD_GET() and get the extracted value.
Add initial support for S2MU005 in the PMIC driver, along with its three
interrupt chips, and support for allowing to fetch revision based on the
device variant.
Co-developed-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://patch.msgid.link/20260516-s2mu005-pmic-v7-4-73f9702fb461@disroot.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for Samsung's S2MPG11 PMIC, which is a Power Management IC
for mobile applications with buck converters, various LDOs, power
meters, NTC thermistor inputs, and additional GPIO interfaces. It
typically complements an S2MPG10 PMIC in a main/sub configuration as
the sub-PMIC.
Like S2MPG10, communication is not via I2C, but via the Samsung ACPM
firmware.
While at it, we can also switch to asynchronous probe, which helps with
probe performance, as the drivers for s2mpg10 and s2mpg11 can probe in
parallel.
Note: The firmware uses the ACPM channel ID and the Speedy channel ID
to select the PMIC address. Since these are firmware properties, they
can not be retrieved from DT, but instead are deducted from the
compatible for now.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-9-3b1f9831fffd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This was used only to allow the s5m RTC driver to deal with the alarm
IRQ. That driver now uses a different approach to acquire that IRQ, and
::irq_data doesn't need to be kept around anymore.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260113-s5m-alarm-v3-3-855a19db1277@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Now that sec-i2c doesn't match device type by pointer casting anymore,
we can switch the device type from unsigned long to int easily.
This saves a few bytes in struct sec_pmic_dev due to member alignment.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-18-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for Samsung's S2MPG10 PMIC, which is a Power Management IC
for mobile applications with buck converters, various LDOs, power
meters, RTC, clock outputs, and additional GPIOs interfaces.
Contrary to existing Samsung S2M series PMICs supported, communication
is not via I2C, but via the Samsung ACPM firmware.
This commit adds the core driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-9-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
sec_irq_init() is an internal API for the core driver, and doesn't
belong into the public header.
Due to an upcoming split of the driver into a core and i2c driver,
we'll also be adding more internal APIs, which again shouldn't be in
the public header.
Move it into a new internal include.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-7-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
sec_irq_resume() was removed in commit 6445b84abf91 ("mfd: Add s2mps11
irq driver") and sec_irq_exit() in commit 3dc6f4aaafbe ("mfd: sec: Use
devm_mfd_add_devices and devm_regmap_add_irq_chip") while the
prototypes were left. They should be removed.
Do so.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-4-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for Samsung's S2MPU05 PMIC. It's the primary PMIC used by
Exynos7870 devices. It houses regulators (21 LDOs and 5 BUCKs) and a RTC
clock device.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250301-exynos7870-pmic-regulators-v3-2-808d0b47a564@disroot.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
S2DOS05 is a panel/touchscreen PMIC, often found in
Samsung phones. We define regulator sub-device for which driver will
be added in subsequent patch. The device also has ADC for power and
current measurements.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240617-starqltechn_integration_upstream-v5-2-ea1109029ba5@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The S5M8763 MFD has no device tree compatible, and since board file
support for it was removed, there's no way to use this MFD. After
removing the remaining code for it from the MFD driver, also remove
support for it in the s5m RTC driver, and all remaining references to
it.
Signed-off-by: David Virag <virag.david003@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131183008.4451-3-virag.david003@gmail.com
|
|
The S5M8751 and S5M8763 PMIC chips have no corresponding compatible
values, so since board file support was removed for this driver, there
is no way to specify these PMICs as present in boards anymore.
Remove leftovers of these chips since it's dead code.
Signed-off-by: David Virag <virag.david003@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131183008.4451-2-virag.david003@gmail.com
|
|
The Samsung PMIC drivers for early chipsets like S5M8767 stored quite a
lot in platform data (struct sec_platform_data). The s5m8767 regulator
driver currently references only some of its fields. Newer regulator
drivers (e.g. s2mps11) use even less platform data fields.
Clean up the structure to reduce memory footprint and source code size.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Set device wakeup capability from devicetree property (done by drivers
core), instead of always setting it to 0 (because value in platform data
is not assigned).
This should not have visible effect on actual resuming from suspend
because the child device - S5M RTC driver - is responsible for waking
up and sets device wakeup unconditionally.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The 'irq_base' field of platform data structure is not assigned,
therefore its default value of 0 has no impact and can be safely
dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The 'device_type' field of platform data structure is not used and can
be safely dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The 'cfg_pmic_irq' field of platform data structure is not used and can
be safely dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Driver did not provide default value for ramp delay for LDOs which lead
to warning in dmesg, e.g. on Odroid XU4:
[ 1.486076] vdd_ldo9: ramp_delay not set
[ 1.506875] vddq_mmc2: ramp_delay not set
[ 1.523766] vdd_ldo15: ramp_delay not set
[ 1.544702] vdd_sd: ramp_delay not set
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for S2MPS15 PMIC which is similar to S2MPS11 PMIC. The S2MPS15
PMIC supports 27 LDO regulators, 10 buck regulators, RTC, three 32.768KHz
clock outputs and battery charger. This patch adds initial support for
LDO and buck regulators of S2MPS15 device.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[Alim: Added s2mps15_devs like rtc and clk and related changes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for Samsung S2MPU02 PMIC device to the MFD sec-core driver.
The S2MPU02 device includes PMIC/RTC/Clock devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The device type was stored in sec_pmic_dev state container twice:
- unsigned long type (initialized from of_device_id or i2c_device_id)
- int device_type (initialized as above or from board files when there
is no DTS)
The 'type' field was never used outside of probe so it can be safely
removed.
Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Update the documentation for sec_pmic state container structure to
reflect current code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The rtc-s5m driver does not support all of S2M and S5M chipsets
supported by main MFD sec-core driver. For such chipsets unsupported by
rtc-s5m, the MFD sec-core driver initialized regmap with default config.
This config in such cases wouldn't work at all.
The main MFD sec-core driver shouldn't initialize regmap for child
drivers which is not used by them and even not valid.
Move the allocation of RTC I2C dummy device and initialization of RTC
regmap from main MFD sec-core driver to the rtc-s5m driver. The rtc-s5m
driver will use proper regmap config for supported devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'regulator/topic/st-pwm', 'regulator/topic/ti-abb', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps6507x', 'regulator/topic/tps65090' and 'regulator/topic/tps65217' into regulator-next
|
|
Add the necessary entries required for S2MPA01 multi-function
device. While at it also convert whitespaces to tabs in core.h.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When used 64bit compiler GCC warns as
drivers/mfd/sec-core.c:199:10: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for GPIO control (enable/disable) over Buck9. The Buck9
Converter is used as a supply for eMMC Host Controller.
BUCK9EN GPIO of S5M8767 chip may be used by application processor to
enable or disable the Buck9. This has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume; Without the patch the regulator supplying
eMMC must be defined as fixed-regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Remove sec_reg* helpers as they are not used anymore. These helpers were
error-prone as they mixed u8 with unsigned int and they changed order of
some of parameters (val and mask in sec_reg_update()).
Also the helpers didn't give any way of useful abstraction as they just
called corresponding regmap function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add real-time clock driver for s5m8767.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Todd Broch <tbroch@chromium.org>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org> [mfd parts]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These were all used by the open coded I/O and IRQ implementations and are
no longer referenced now that the regmap core variants are used instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch support irq handling driver for s2mps11.
As this patch use regmap_irq, s5m8767 and s5m8763 are modified with
regmap_irq.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch add Samsung S2MPS11 mfd driver.
The S2MPS11 can support regulators and RTC.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
