| Age | Commit message (Collapse) | Author |
|---|
|
In 64-bit configurations calling the initial console output handler from
a kernel thread other than the initial one will result in a situation
where the stack has been placed in the XKPHYS 64-bit memory segment and
consequently so has been the buffer allocated there that is used as the
argument corresponding to the `%s' output conversion specifier for the
firmware's printf() entry point.
This 64-bit address will then be truncated by 32-bit firmware, resulting
in an attempt to access the wrong memory location, which in turn will
cause all kinds of unpredictable behaviour, such as a kernel crash:
Console: colour dummy device 160x64
Calibrating delay loop... 49.36 BogoMIPS (lpj=192512)
pid_max: default: 32768 minimum: 301
CPU 0 Unable to handle kernel paging request at virtual address 000000000203bd00, epc == ffffffffbfc08364, ra == ffffffffbfc08800
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc2-00254-gfb649bda6f56-dirty #121
$ 0 : 0000000000000000 0000000000000001 0000000000000023 ffffffff80684ba0
$ 4 : 000000000203bd00 ffffffffbfc0f3b4 ffffffffffffffff 0000000000000073
$ 8 : 0a303d7469000000 0000000000000000 0000000000000073 ffffffffbfc0f473
$12 : 0000000000000002 0000000000000000 ffffffff80684c1c 0000000000000000
$16 : 0000000000000000 ffffffff80596dc9 0000000000000000 ffffffffbfc09240
$20 : ffffffff80684c40 ffffffffbfc0f400 000000000000002d 000000000000002b
$24 : ffffffffffffffbf 000000000203bd00
$28 : ffffffff805f0000 ffffffff80684b58 0000000000000030 ffffffffbfc08800
Hi : 0000000000000000
Lo : 0000000000000aa8
epc : ffffffffbfc08364 0xffffffffbfc08364
ra : ffffffffbfc08800 0xffffffffbfc08800
Status: 140120e2 KX SX UX KERNEL EXL
Cause : 00000008 (ExcCode 02)
BadVA : 000000000203bd00
PrId : 00000430 (R4000SC)
Modules linked in:
Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____), tls=0000000000000000)
Stack : 0000000000000000 0000000000000000 0000000000000000 0000004d0000004d
80684cc0806a2a40 80596dc80000004d 8061000000000000 bfc0850c80684c38
0000000000000000 000000000203bd00 0000000000000000 0000000000000000
0000000000000000 00000000bfc0f3b4 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000002500000000 0000000000000000 0000000000000000 802c1a7400000000
0203bd0080596dc8 0203bd4d69000000 6c61632000000018 5f746567646e6172
6c616320625f6d6f 5f736e5f6d6f7266 206361323778302b 303d74696e726320
806a0a38806b0000 806a0a38806b0000 00000000806b0000 80683c58806b0000
...
Call Trace:
Code: a082ffff 03e00008 00601021 <80820000> 00001821 10400005 24840001 80820000 24630001
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception in interrupt
KN04 V2.1k (PC: 0xa0026768, SP: 0x806848e8)
>>
In this case the pointer in $4 was truncated from 0x980000000203bd00 to
0x000000000203bd00.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started.
Fix the issue by making the buffer static and initdata, and therefore
placed in the CKSEG0 32-bit compatibility segment, observing that the
console output handler is called with the console lock held, implying
no need for this code to be reentrant. Add an assertion to verify the
buffer actually has been placed in a compatibility segment.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
In 64-bit configurations calling any firmware entry points from a kernel
thread other than the initial one will result in a situation where the
stack has been placed in the XKPHYS 64-bit memory segment.
Consequently the stack pointer is no longer a 32-bit value and when the
32-bit firmware code called uses 32-bit ALU operations to manipulate the
stack pointer, the calculated result is incorrect (in fact in the 64-bit
MIPS ISA almost all 32-bit ALU operations will produce an unpredictable
result when executed on 64-bit data) and control goes astray.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap, or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started, and the kernel will hang at:
pid_max: default: 32768 minimum: 301
or somewhat later, but always before:
cblist_init_generic: Setting adjustable number of callback queues.
has been printed.
It seems that only the prom_printf() entry point is affected. Of all
the other entry points wired only rex_slot_address() and rex_gettcinfo()
are called from a kernel thread other than the initial one, specifically
kernel_init(), and they are leaf functions that do no business with the
stack, having worked with no issue ever since 64-bit support was added
for the platform back in 2002.
To address this issue then, arrange for the stack to be switched in the
o32 wrapper as required for prom_printf() only, by supplying call_o32()
with a pointer to a chunk of initdata space, which is placed in the
CKSEG0 32-bit compatibility segment, observing that prom_printf() is
only called from console output handler and therefore with the console
lock held, implying no need for this code to be reentrant.
Other firmware entry points may be called with interrupts enabled and no
lock held, and may therefore require that call_o32() be reentrant. They
trigger no issue at this point and "if it ain't broke, don't fix it," so
just leave them alone.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Declare which_prom() as static to suppress gcc compiler warning that
'missing-prototypes'. This function is not intended to be called
from other parts.
Fix follow error with gcc-14 when -Werror:
arch/mips/dec/prom/init.c:45:13: error: no previous prototype for ‘which_prom’ [-Werror=missing-prototypes]
45 | void __init which_prom(s32 magic, s32 *prom_vec)
| ^~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:207: arch/mips/dec/prom/init.o] Error 1
make[5]: *** [scripts/Makefile.build:465: arch/mips/dec/prom] Error 2
make[5]: *** Waiting for unfinished jobs....
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Recent tightening of the opcode table in binutils so as to consistently
disallow the assembly or disassembly of CP0 instructions not supported
by the processor architecture chosen has caused a regression like below:
arch/mips/dec/prom/locore.S: Assembler messages:
arch/mips/dec/prom/locore.S:29: Error: opcode not supported on this processor: r4600 (mips3) `rfe'
in a piece of code used to probe for memory with PMAX DECstation models,
which have non-REX firmware. Those computers always have an R2000 CPU
and consequently the exception handler used in memory probing uses the
RFE instruction, which those processors use.
While adding 64-bit support this code was correctly excluded for 64-bit
configurations, however it should have also been excluded for irrelevant
32-bit configurations. Do this now then, and only enable PMAX memory
probing for R3k systems.
Reported-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
message
The config for MIPS R4000-series processors is named CPU_R4X00 with
upper-case X, not CPU_R4x00 as the error message suggests.
Hence, ./scripts/checkkconfigsymbols.py reports this invalid reference:
CPU_R4x00
Referencing files: arch/mips/dec/prom/init.c
When human users encounter this error message, they probably just deal
with this minor discrepancy; so, the spelling never was a big deal here.
Still, the script ./scripts/checkkconfigsymbols.py has been quite useful
to identify a number of bugs with Kconfig symbols and deserves to be
executed and checked regularly.
So, repair the error message to reduce the reports made the script and
simplify to use this script, as new issues are easier to spot when the
list of reports is shorter.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Drop inline for memory setup functions and mark them __init to
fix section mismatch of pmax_setup_memory_region.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
|
|
add_memory_region was the old interface for registering memory and
was already changed to used memblock internaly. Replace it by
directly calling memblock functions.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While examining output from trial builds with -Wformat-security enabled,
many strings were found that should be defined as "const", or as a char
array instead of char pointer. This makes some static analysis easier,
by producing fewer false positives.
As these are all trivial changes, it seemed best to put them all in a
single patch rather than chopping them up per maintainer.
Link: http://lkml.kernel.org/r/20170405214711.GA5711@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jes Sorensen <jes@trained-monkey.org> [runner.c]
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Daode Huang <huangdaode@hisilicon.com>
Cc: Qianqian Xie <xieqianqian@huawei.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christian Gromm <christian.gromm@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Cc: Jason Litzinger <jlitzingerdev@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some code where it is modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h might have been the implicit source for init.h
(for __init) and for export.h (for EXPORT_SYMBOL) we consider each
instance for the presence of either and replace/add as needed.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Build coverage of all the mips defconfigs revealed the module.h
header was masking a couple of implicit include instances, so
we add the appropriate headers there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15131/
[james.hogan@imgtec.com: Preserve sort order where it already exists]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Commit 231a35d37293ab88d325a9cb94e5474c156282c0 [[MIPS] RM: Collected
changes] broke DECstation support by introducing an incompatible copy of
arch/mips/dec/prom/call_o32.S in arch/mips/fw/lib/, built unconditionally.
The copy happens to land earlier of the two among the modules used in the
link and is therefore chosen for the DECstation rather than the intended
original. As a result random kernel data is corrupted because a pointer
to the "%s" formatted output template is used as a temporary stack pointer
rather than being passed down to prom_printf. This also explains why
prom_printf still works, up to a point -- the next argument is the actual
string to output so it works just fine as the output template until enough
kernel data has been corrupted to cause a crash.
This change adjusts the modified wrapper in arch/mips/fw/lib/call_o32.S to
let callers request no stack switching by passing a null temporary stack
pointer in $a1, reworks the DECstation callers to work with the updated
interface and removes the old copy from arch/mips/dec/prom/call_o32.S. A
few minor readability adjustments are included as well, most importantly
O32_SZREG is now used throughout where applicable rather than hardcoded
multiplies of 4 and $fp is used to access the argument save area as a more
usual register to operate the stack with rather than $s0.
Finally an update is made to the temporary stack space used by the SNI
platform to guarantee 8-byte alignment as per o32 requirements.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 7034228792cc561e79ff8600f02884bd4c80e287 [MIPS: Whitespace
cleanup.] did a lot of good and a little damage. Revert the damage.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
o Move current_cpu_type() to a separate header file
o #ifdefing on supported CPU types lets modern GCC know that certain
code in callers may be discarded ideally turning current_cpu_type() into
a function returning a constant.
o Use current_cpu_type() rather than direct access to struct cpuinfo_mips.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5833/
|
|
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Recent git versions now warn about those and they've always been a bit of
an annoyance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
|
|
This saves a few k on systems which only ever ship with a single CPU type.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This has not been any serious user of this ill conceived thing since the
original invention in like '95.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Convert old/obsolete NORET_TYPE and ATTRIB_NORET macros to use the
newer standard of "__noreturn" as defined in compiler-gcc.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Register_prom_console was removed when mips was converted to early printk.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
early_printk is a so much saner thing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Many Makefiles in arch/mips have EXTRA_AFLAGS := $(CFLAGS) line. This
is redundant while AFLAGS contains $(cflags-y) and any options only
listed in CFLAGS (not in cflags-y) should be unnecessary for asm
sources.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This is the platform-specific part of TURBOchannel bus support for the
DECstation. It implements determining whether the bus is actually there,
getting bus parameters, IRQ assignments for devices and protected accesses
to possibly unoccupied slots that may trigger bus error exceptions.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Current prom_free_prom_memory() implementations are almost same as
free_init_pages(), or no-op. Make free_init_pages() extern (again)
and make prom_free_prom_memory() use it.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
While at it, change message on DEC for consistency.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
them as appropriate.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Start cleaning 32-bit vs. 64-bit configuration.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
