Merge branch 'for-next' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git

11 files changed, 436 insertions, 220 deletions

diff --git a/Documentation/devicetree/bindings/sound/cirrus,cs35l36.yaml b/Documentation/devicetree/bindings/sound/cirrus,cs35l36.yaml
new file mode 100644
index 000000000000..2a142b32acf5
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cirrus,cs35l36.yaml
@@ -0,0 +1,240 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/cirrus,cs35l36.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic CS35L36 Speaker Amplifier
+
+maintainers:
+  - David Rhodes <drhodes@opensource.cirrus.com>
+  - patches@opensource.cirrus.com
+
+description:
+  CS35L36 is a boosted mono Class D amplifier
+
+allOf:
+  - $ref: dai-common.yaml#
+
+properties:
+  compatible:
+    enum:
+      - cirrus,cs35l36
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  VA-supply:
+    description: Voltage regulator of analog internal section
+
+  VP-supply:
+    description: Voltage regulator of boost converter
+
+  reset-gpios:
+    maxItems: 1
+
+  cirrus,boost-ctl-millivolt:
+    description: Boost converter output voltage (step 50)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 2550
+    maximum: 12000
+
+  cirrus,boost-peak-milliamp:
+    description: Boost-converter peak current limit (step 50)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 4500
+    minimum: 1600
+    maximum: 4500
+
+  cirrus,boost-ind-nanohenry:
+    description: Initial inductor estimation reference value (1000=1μH, 1200=1.2μH)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 1000
+
+  cirrus,multi-amp-mode:
+    description: Hi-Z ASP port when more than one amplifier in system
+    type: boolean
+
+  cirrus,boost-ctl-select:
+    description: Boost converter control source selection
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 1
+    enum:
+      - 0 # Control Port
+      - 1 # Class
+      - 2 # Sync
+
+  cirrus,amp-pcm-inv:
+    description: Invert incoming PCM data when true
+    type: boolean
+
+  cirrus,imon-pol-inv:
+    description: Invert polarity of outbound IMON feedback when true
+    type: boolean
+
+  cirrus,vmon-pol-inv:
+    description: Invert polarity of outbound VMON feedback when true
+    type: boolean
+
+  cirrus,dcm-mode-enable:
+    description: Enable boost converter automatic Discontinuous Conduction Mode
+    type: boolean
+
+  cirrus,weak-fet-disable:
+    description: Reduce output driver strength in Weak-FET Drive Mode when true
+    type: boolean
+
+  cirrus,classh-wk-fet-delay-ms:
+    description: Weak-FET entry delay
+    default: 100
+    enum: [0, 5, 10, 50, 100, 200, 500, 1000]
+
+  cirrus,classh-weak-fet-thld-millivolt:
+    description: Weak-FET drive threshold
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700]
+
+  cirrus,temp-warn-threshold:
+    description: Overtemperature warning threshold
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 2
+    enum:
+      - 0 # 105°C
+      - 1 # 115°C
+      - 2 # 125°C
+      - 3 # 135°C
+
+  cirrus,irq-drive-select:
+    description: Interrupt output driver type
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 1
+    enum:
+      - 0 # open-drain
+      - 1 # push-pull
+
+  cirrus,irq-gpio-select:
+    description: Programmable IRQ pin selection
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum:
+      - 0 # PDM_DATA/SWIRE_SD/INT
+      - 1 # GPIO
+
+  cirrus,vpbr-config:
+    $ref: "#/$defs/vpbr-config"
+
+$defs:
+  vpbr-config:
+    description: Brownout prevention configuration sub-node
+    type: object
+    additionalProperties: false
+
+    properties:
+      cirrus,vpbr-en:
+        description: VBST brownout prevention enable
+        $ref: /schemas/types.yaml#/definitions/uint32
+        default: 0
+        enum:
+          - 0 # disabled
+          - 1 # enabled
+
+      cirrus,vpbr-thld:
+        description: Initial VPBR threshold voltage
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 2
+        maximum: 31
+
+      cirrus,vpbr-atk-rate:
+        description: Attenuation attack step rate
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 7
+
+      cirrus,vpbr-atk-vol:
+        description: VP brownout prevention step size
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 7
+
+      cirrus,vpbr-max-attn:
+        description: Maximum attenuation during VP brownout prevention (dB)
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 15
+
+      cirrus,vpbr-wait:
+        description: Delay between brownout clearance and attenuation release (ms)
+        $ref: /schemas/types.yaml#/definitions/uint32
+        default: 1
+        enum:
+          - 0 # 10
+          - 1 # 100
+          - 2 # 250
+          - 3 # 500
+
+      cirrus,vpbr-rel-rate:
+        description: Attenuation release step rate
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 7
+
+      cirrus,vpbr-mute-en:
+        description: Mute audio if maximum attenuation reached
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - VA-supply
+  - cirrus,boost-ctl-millivolt
+  - cirrus,boost-peak-milliamp
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        codec@40 {
+            compatible = "cirrus,cs35l36";
+            reg = <0x40>;
+            VA-supply = <&dummy_vreg>;
+            VP-supply = <&dummy_vreg>;
+            reset-gpios = <&gpio0 54 GPIO_ACTIVE_HIGH>;
+            interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+            cirrus,boost-ind-nanohenry = <1000>;
+            cirrus,boost-ctl-millivolt = <10000>;
+            cirrus,boost-peak-milliamp = <4500>;
+            cirrus,boost-ctl-select = <0>;
+            cirrus,classh-wk-fet-delay-ms = <100>;
+            cirrus,classh-weak-fet-thld-millivolt = <100>;
+            cirrus,temp-warn-threshold = <1>;
+            cirrus,multi-amp-mode;
+            cirrus,irq-drive-select = <1>;
+            cirrus,irq-gpio-select = <1>;
+
+            cirrus,vpbr-config {
+                cirrus,vpbr-en = <0>;
+                cirrus,vpbr-thld = <5>;
+                cirrus,vpbr-atk-rate = <2>;
+                cirrus,vpbr-atk-vol = <1>;
+                cirrus,vpbr-max-attn = <9>;
+                cirrus,vpbr-wait = <1>;
+                cirrus,vpbr-rel-rate = <5>;
+                cirrus,vpbr-mute-en = <0>;
+            };
+        };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/sound/cs35l36.txt b/Documentation/devicetree/bindings/sound/cs35l36.txt
deleted file mode 100644
index d34117b8558e..000000000000
--- a/Documentation/devicetree/bindings/sound/cs35l36.txt
+++ /dev/null
@@ -1,168 +0,0 @@
-CS35L36 Speaker Amplifier
-
-Required properties:
-
-  - compatible : "cirrus,cs35l36"
-
-  - reg : the I2C address of the device for I2C
-
-  - VA-supply, VP-supply : power supplies for the device,
-  as covered in
-  Documentation/devicetree/bindings/regulator/regulator.txt.
-
-  - cirrus,boost-ctl-millivolt : Boost Voltage Value.  Configures the boost
-  converter's output voltage in mV. The range is from 2550mV to 12000mV with
-  increments of 50mV.
-  (Default) VP
-
-  - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
-  Configures the peak current by monitoring the current through the boost FET.
-  Range starts at 1600mA and goes to a maximum of 4500mA with increments of
-  50mA.
-  (Default) 4.50 Amps
-
-  - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
-  Seeds the digital boost converter's inductor estimation block with the initial
-  inductance value to reference.
-
-  1000 = 1uH (Default)
-  1200 = 1.2uH
-
-Optional properties:
-  - cirrus,multi-amp-mode : Boolean to determine if there are more than
-  one amplifier in the system. If more than one it is best to Hi-Z the ASP
-  port to prevent bus contention on the output signal
-
-  - cirrus,boost-ctl-select : Boost converter control source selection.
-  Selects the source of the BST_CTL target VBST voltage for the boost
-  converter to generate.
-  0x00 - Control Port Value
-  0x01 - Class H Tracking (Default)
-  0x10 - MultiDevice Sync Value
-
-  - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
-  PCM data
-
-  - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
-  polarity of outbound IMON feedback data
-
-  - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
-  polarity of outbound VMON feedback data
-
-  - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
-  This enables the digital boost converter to operate in a low power
-  (Discontinuous Conduction) mode during low loading conditions.
-
-  - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
-  reduced when operating in a Weak-FET Drive Mode and must not be used to drive
-  a large load.
-
-  - cirrus,classh-wk-fet-delay :  Weak-FET entry delay. Controls the delay
-  (in ms) before the Class H algorithm switches to the weak-FET voltage
-  (after the audio falls and remains below the value specified in WKFET_AMP_THLD).
-
-  0 = 0ms
-  1 = 5ms
-  2 = 10ms
-  3 = 50ms
-  4 = 100ms (Default)
-  5 = 200ms
-  6 = 500ms
-  7 = 1000ms
-
-  - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
-  Configures the signal threshold at which the PWM output stage enters
-  weak-FET operation. The range is 50mV to 700mV in 50mV increments.
-
-  - cirrus,temp-warn-threshold :  Amplifier overtemperature warning threshold.
-  Configures the threshold at which the overtemperature warning condition occurs.
-  When the threshold is met, the overtemperature warning attenuation is applied
-  and the TEMP_WARN_EINT interrupt status bit is set.
-  If TEMP_WARN_MASK = 0, INTb is asserted.
-
-  0 = 105C
-  1 = 115C
-  2 = 125C (Default)
-  3 = 135C
-
-  - cirrus,irq-drive-select : Selects the driver type of the selected interrupt
-  output.
-
-  0 = Open-drain
-  1 = Push-pull (Default)
-
-  - cirrus,irq-gpio-select : Selects the pin to serve as the programmable
-  interrupt output.
-
-  0 = PDM_DATA / SWIRE_SD / INT (Default)
-  1 = GPIO
-
-Optional properties for the "cirrus,vpbr-config" Sub-node
-
-  - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the
-  VBST brownout prevention algorithm is enabled or disabled.
-
-  0 = VBST brownout prevention disabled (default)
-  1 = VBST brownout prevention enabled
-
-  See Section 7.31.1 VPBR Config for configuration options & further details
-
-  - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout
-  threshold voltage
-
-  - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the
-  amount delay between consecutive volume attenuation steps when a brownout
-  condition is present and the VP brownout condition is in an attacking state.
-
-  - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP
-  brownout prevention attacking attenuation step size when operating in either
-  digital volume or analog gain modes.
-
-  - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention
-  can apply to the audio signal.
-
-  - cirrus,vpbr-wait : Configures the delay time between a brownout condition
-  no longer being present and the VP brownout prevention entering an attenuation
-  release state.
-
-  - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay
-  between consecutive volume attenuation release steps when a brownout condition
-  is not longer present and the VP brownout is in an attenuation release state.
-
-  - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value
-  is reached, the error condition still remains, and this bit is set, the audio
-  is muted.
-
-Example:
-
-cs35l36: cs35l36@40 {
-	compatible = "cirrus,cs35l36";
-	reg = <0x40>;
-	VA-supply = <&dummy_vreg>;
-	VP-supply = <&dummy_vreg>;
-	reset-gpios = <&gpio0 54 0>;
-	interrupt-parent = <&gpio8>;
-	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
-
-	cirrus,boost-ind-nanohenry = <1000>;
-	cirrus,boost-ctl-millivolt = <10000>;
-	cirrus,boost-peak-milliamp = <4500>;
-	cirrus,boost-ctl-select = <0x00>;
-	cirrus,weak-fet-delay = <0x04>;
-	cirrus,weak-fet-thld = <0x01>;
-	cirrus,temp-warn-threshold = <0x01>;
-	cirrus,multi-amp-mode;
-	cirrus,irq-drive-select = <0x01>;
-	cirrus,irq-gpio-select = <0x01>;
-
-	cirrus,vpbr-config {
-		cirrus,vpbr-en = <0x00>;
-		cirrus,vpbr-thld = <0x05>;
-		cirrus,vpbr-atk-rate = <0x02>;
-		cirrus,vpbr-atk-vol = <0x01>;
-		cirrus,vpbr-max-attn = <0x09>;
-		cirrus,vpbr-wait = <0x01>;
-		cirrus,vpbr-rel-rate = <0x05>;
-		cirrus,vpbr-mute-en = <0x00>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/sound/dmic-codec.yaml b/Documentation/devicetree/bindings/sound/dmic-codec.yaml
index cc3c84dd4c26..83c23e029ea4 100644
--- a/Documentation/devicetree/bindings/sound/dmic-codec.yaml
+++ b/Documentation/devicetree/bindings/sound/dmic-codec.yaml
@@ -39,6 +39,10 @@ properties:
   wakeup-delay-ms:
     description: Delay (in ms) after enabling the DMIC
 
+  port:
+    $ref: audio-graph-port.yaml#
+    unevaluatedProperties: false
+
 required:
   - compatible
 
diff --git a/Documentation/devicetree/bindings/sound/fsl,micfil.yaml b/Documentation/devicetree/bindings/sound/fsl,micfil.yaml
index c47b7a097490..4c7dadb310de 100644
--- a/Documentation/devicetree/bindings/sound/fsl,micfil.yaml
+++ b/Documentation/devicetree/bindings/sound/fsl,micfil.yaml
@@ -66,6 +66,10 @@ properties:
   "#sound-dai-cells":
     const: 0
 
+  port:
+    $ref: audio-graph-port.yaml#
+    unevaluatedProperties: false
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/sound/loongson,ls-audio-card.yaml b/Documentation/devicetree/bindings/sound/loongson,ls-audio-card.yaml
index 61e8babed402..dc7f4afbb777 100644
--- a/Documentation/devicetree/bindings/sound/loongson,ls-audio-card.yaml
+++ b/Documentation/devicetree/bindings/sound/loongson,ls-audio-card.yaml
@@ -8,19 +8,22 @@ title: Loongson 7axxx/2kxxx ASoC audio sound card driver
 
 maintainers:
   - Yingkun Meng <mengyingkun@loongson.cn>
+  - Binbin Zhou <zhoubinbin@loongson.cn>
 
 description:
   The binding describes the sound card present in loongson
   7axxx/2kxxx platform. The sound card is an ASoC component
   which uses Loongson I2S controller to transfer the audio data.
 
+allOf:
+  - $ref: sound-card-common.yaml#
+
 properties:
   compatible:
-    const: loongson,ls-audio-card
-
-  model:
-    $ref: /schemas/types.yaml#/definitions/string
-    description: User specified audio sound card name
+    enum:
+      - loongson,ls-audio-card  # Loongson-2K1000/Loongson-2K2000/LS7A
+      - loongson,ls2k0300-forever-pi-audio-card # CTCISZ Forever Pi
+      - loongson,ls2k0300-dl2k0300b-audio-card # ATK-DL2K0300B
 
   mclk-fs:
     $ref: simple-card.yaml#/definitions/mclk-fs
@@ -45,14 +48,25 @@ properties:
     required:
       - sound-dai
 
+  spkr-en-gpios:
+    maxItems: 1
+    description: The GPIO that enables the speakers
+
+  hp-ctl-gpios:
+    maxItems: 1
+    description: The GPIO that control the headphones
+
+  hp-det-gpios:
+    maxItems: 1
+    description: The GPIO that detect headphones are plugged in
+
 required:
   - compatible
-  - model
   - mclk-fs
   - cpu
   - codec
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |
@@ -68,3 +82,28 @@ examples:
              sound-dai = <&es8323>;
         };
     };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    sound {
+        compatible = "loongson,ls2k0300-dl2k0300b-audio-card";
+        model = "loongson-audio";
+        mclk-fs = <512>;
+        hp-det-gpios = <&gpio 81 GPIO_ACTIVE_HIGH>;
+        spkr-en-gpios = <&gpio 86 GPIO_ACTIVE_HIGH>;
+        hp-ctl-gpios = <&gpio 87 GPIO_ACTIVE_HIGH>;
+        audio-routing =
+                      "Headphone", "LOUT1",
+                      "Headphone", "ROUT1",
+                      "Speaker", "LOUT2",
+                      "Speaker", "ROUT2";
+
+        cpu {
+            sound-dai = <&i2s>;
+        };
+
+        codec {
+             sound-dai = <&es8388>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/sound/loongson,ls2k1000-i2s.yaml b/Documentation/devicetree/bindings/sound/loongson,ls2k1000-i2s.yaml
index da79510bb2d9..51e23c189f7a 100644
--- a/Documentation/devicetree/bindings/sound/loongson,ls2k1000-i2s.yaml
+++ b/Documentation/devicetree/bindings/sound/loongson,ls2k1000-i2s.yaml
@@ -14,9 +14,12 @@ allOf:
 
 properties:
   compatible:
-    const: loongson,ls2k1000-i2s
+    enum:
+      - loongson,ls2k0300-i2s
+      - loongson,ls2k1000-i2s
 
   reg:
+    minItems: 1
     items:
       - description: Loongson I2S controller Registers.
       - description: APB DMA config register for Loongson I2S controller.
@@ -49,6 +52,23 @@ required:
 
 unevaluatedProperties: false
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - loongson,ls2k1000-i2s
+
+then:
+  properties:
+    reg:
+      minItems: 2
+
+else:
+  properties:
+    reg:
+      maxItems: 1
+
 examples:
   - |
     #include <dt-bindings/clock/loongson,ls2k-clk.h>
diff --git a/Documentation/devicetree/bindings/sound/mediatek,mtk-btcvsd-snd.yaml b/Documentation/devicetree/bindings/sound/mediatek,mtk-btcvsd-snd.yaml
new file mode 100644
index 000000000000..1b7451655476
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/mediatek,mtk-btcvsd-snd.yaml
@@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/mediatek,mtk-btcvsd-snd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek ALSA BT SCO CVSD/MSBC
+
+maintainers:
+  - Luca Leonardo Scorcia <l.scorcia@gmail.com>
+
+properties:
+  compatible:
+    const: mediatek,mtk-btcvsd-snd
+
+  reg:
+    items:
+      - description: PKV region
+      - description: SRAM_BANK2 region
+
+  interrupts:
+    items:
+      - description: BT-SCO interrupt
+
+  mediatek,infracfg:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: The phandle of the infracfg controller
+
+  mediatek,offset:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: Array of register offsets and masks
+    items:
+      - description: infra_misc_offset
+      - description: infra_conn_bt_cvsd_mask
+      - description: cvsd_mcu_read_offset
+      - description: cvsd_mcu_write_offset
+      - description: cvsd_packet_indicator_offset
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - mediatek,infracfg
+  - mediatek,offset
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    mtk-btcvsd-snd@18000000 {
+      compatible = "mediatek,mtk-btcvsd-snd";
+      reg = <0x18000000 0x1000>,
+            <0x18080000 0x8000>;
+      interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_LOW>;
+      mediatek,infracfg = <&infrasys>;
+      mediatek,offset = <0xf00 0x800 0xfd0 0xfd4 0xfd8>;
+    };
diff --git a/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt b/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt
deleted file mode 100644
index 679e44839b48..000000000000
--- a/Documentation/devicetree/bindings/sound/mtk-btcvsd-snd.txt
+++ /dev/null
@@ -1,24 +0,0 @@
-Mediatek ALSA BT SCO CVSD/MSBC Driver
-
-Required properties:
-- compatible = "mediatek,mtk-btcvsd-snd";
-- reg: register location and size of PKV and SRAM_BANK2
-- interrupts: should contain BTSCO interrupt
-- mediatek,infracfg: the phandles of INFRASYS
-- mediatek,offset: Array contains of register offset and mask
-    infra_misc_offset,
-    infra_conn_bt_cvsd_mask,
-    cvsd_mcu_read_offset,
-    cvsd_mcu_write_offset,
-    cvsd_packet_indicator_offset
-
-Example:
-
-	mtk-btcvsd-snd@18000000 {
-		compatible = "mediatek,mtk-btcvsd-snd";
-		reg=<0 0x18000000 0 0x1000>,
-		    <0 0x18080000 0 0x8000>;
-		interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_LOW>;
-		mediatek,infracfg = <&infrasys>;
-		mediatek,offset = <0xf00 0x800 0xfd0 0xfd4 0xfd8>;
-	};
diff --git a/Documentation/devicetree/bindings/sound/omap-dmic.txt b/Documentation/devicetree/bindings/sound/omap-dmic.txt
deleted file mode 100644
index 418e30e72e89..000000000000
--- a/Documentation/devicetree/bindings/sound/omap-dmic.txt
+++ /dev/null
@@ -1,20 +0,0 @@
-* Texas Instruments OMAP4+ Digital Microphone Module
-
-Required properties:
-- compatible: "ti,omap4-dmic"
-- reg: Register location and size as an array:
-       <MPU access base address, size>,
-       <L3 interconnect address, size>;
-- interrupts: Interrupt number for DMIC
-- ti,hwmods: Name of the hwmod associated with OMAP dmic IP
-
-Example:
-
-dmic: dmic@4012e000 {
-	compatible = "ti,omap4-dmic";
-	reg = <0x4012e000 0x7f>, /* MPU private access */
-	      <0x4902e000 0x7f>; /* L3 Interconnect */
-	interrupts = <0 114 0x4>;
-	interrupt-parent = <&gic>;
-	ti,hwmods = "dmic";
-};
diff --git a/Documentation/devicetree/bindings/sound/ti,omap4-dmic.yaml b/Documentation/devicetree/bindings/sound/ti,omap4-dmic.yaml
new file mode 100644
index 000000000000..773b9bf2f1c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/ti,omap4-dmic.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/ti,omap4-dmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments OMAP4+ Digital Microphone Module
+
+maintainers:
+  - Peter Ujfalusi <peter.ujfalusi@ti.com>
+
+properties:
+  compatible:
+    const: ti,omap4-dmic
+
+  reg:
+    items:
+      - description: MPU access base address
+      - description: L3 interconnect address
+
+  reg-names:
+    items:
+      - const: mpu
+      - const: dma
+
+  interrupts:
+    maxItems: 1
+
+  dmas:
+    maxItems: 1
+
+  dma-names:
+    items:
+      - const: up_link
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - dmas
+  - dma-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    dmic@0 {
+      compatible = "ti,omap4-dmic";
+      reg = <0x0 0x7f>, /* MPU private access */
+            <0x4902e000 0x7f>; /* L3 Interconnect */
+      reg-names = "mpu", "dma";
+      interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+      dmas = <&sdma 67>;
+      dma-names = "up_link";
+    };
diff --git a/Documentation/devicetree/bindings/sound/wlf,wm8524.yaml b/Documentation/devicetree/bindings/sound/wlf,wm8524.yaml
index 4d951ece394e..dffc41d5f7de 100644
--- a/Documentation/devicetree/bindings/sound/wlf,wm8524.yaml
+++ b/Documentation/devicetree/bindings/sound/wlf,wm8524.yaml
@@ -24,6 +24,10 @@ properties:
     description:
       a GPIO spec for the MUTE pin.
 
+  port:
+    $ref: audio-graph-port.yaml#
+    unevaluatedProperties: false
+
 required:
   - compatible
   - wlf,mute-gpios