blob: bcb4f004bed5784b7824a5df777f3c9b99196ac1 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
*/
#ifndef _UFS_QUIRKS_H_
#define _UFS_QUIRKS_H_
/* return true if s1 is a prefix of s2 */
#define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1))
#define UFS_ANY_VENDOR 0xFFFF
#define UFS_ANY_MODEL "ANY_MODEL"
#define UFS_VENDOR_MICRON 0x12C
#define UFS_VENDOR_SAMSUNG 0x1CE
#define UFS_VENDOR_SKHYNIX 0x1AD
#define UFS_VENDOR_TOSHIBA 0x198
#define UFS_VENDOR_WDC 0x145
/**
* ufs_dev_quirk - ufs device quirk info
* @card: ufs card details
* @quirk: device quirk
*/
struct ufs_dev_quirk {
u16 wmanufacturerid;
const u8 *model;
unsigned int quirk;
};
/*
* Some vendor's UFS device sends back to back NACs for the DL data frames
* causing the host controller to raise the DFES error status. Sometimes
* such UFS devices send back to back NAC without waiting for new
* retransmitted DL frame from the host and in such cases it might be possible
* the Host UniPro goes into bad state without raising the DFES error
* interrupt. If this happens then all the pending commands would timeout
* only after respective SW command (which is generally too large).
*
* We can workaround such device behaviour like this:
* - As soon as SW sees the DL NAC error, it should schedule the error handler
* - Error handler would sleep for 50ms to see if there are any fatal errors
* raised by UFS controller.
* - If there are fatal errors then SW does normal error recovery.
* - If there are no fatal errors then SW sends the NOP command to device
* to check if link is alive.
* - If NOP command times out, SW does normal error recovery
* - If NOP command succeed, skip the error handling.
*
* If DL NAC error is seen multiple times with some vendor's UFS devices then
* enable this quirk to initiate quick error recovery and also silence related
* error logs to reduce spamming of kernel logs.
*/
#define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2)
/*
* Few Toshiba UFS device models advertise RX_MIN_ACTIVATETIME_CAPABILITY as
* 600us which may not be enough for reliable hibern8 exit hardware sequence
* from UFS device.
* To workaround this issue, host should set its PA_TACTIVATE time to 1ms even
* if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms.
*/
#define UFS_DEVICE_QUIRK_PA_TACTIVATE (1 << 4)
/*
* It seems some UFS devices may keep drawing more than sleep current
* (atleast for 500us) from UFS rails (especially from VCCQ rail).
* To avoid this situation, add 2ms delay before putting these UFS
* rails in LPM mode.
*/
#define UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM (1 << 6)
/*
* Some UFS devices require host PA_TACTIVATE to be lower than device
* PA_TACTIVATE, enabling this quirk ensure this.
*/
#define UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE (1 << 7)
/*
* The max. value PA_SaveConfigTime is 250 (10us) but this is not enough for
* some vendors.
* Gear switch from PWM to HS may fail even with this max. PA_SaveConfigTime.
* Gear switch can be issued by host controller as an error recovery and any
* software delay will not help on this case so we need to increase
* PA_SaveConfigTime to >32us as per vendor recommendation.
*/
#define UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME (1 << 8)
/*
* Some UFS devices require VS_DebugSaveConfigTime is 0x10,
* enabling this quirk ensure this.
*/
#define UFS_DEVICE_QUIRK_HOST_VS_DEBUGSAVECONFIGTIME (1 << 9)
/*
* Some pre-3.1 UFS devices can support extended features by upgrading
* the firmware. Enable this quirk to make UFS core driver probe and enable
* supported features on such devices.
*/
#define UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES (1 << 10)
/*
* Some UFS devices require delay after VCC power rail is turned-off.
* Enable this quirk to introduce 5ms delays after VCC power-off during
* suspend flow.
*/
#define UFS_DEVICE_QUIRK_DELAY_AFTER_LPM (1 << 11)
/*
* Some UFS devices require L2P entry should be swapped before being sent to the
* UFS device for HPB READ command.
*/
#define UFS_DEVICE_QUIRK_SWAP_L2P_ENTRY_FOR_HPB_READ (1 << 12)
#endif /* UFS_QUIRKS_H_ */
|
