1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
|
Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
The QUP core is an AHB slave that provides a common data path (an output FIFO
and an input FIFO) for serial peripheral interface (SPI) mini-core.
SPI in master mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
Required properties:
- compatible: Should contain "qcom,spi-qup-v2.1.1" or "qcom,spi-qup-v2.2.1"
- reg: Should contain base register location and length
- interrupts: Interrupt number used by this controller
- clocks: Should contain the core clock and the AHB clock.
- clock-names: Should be "core" for the core clock and "iface" for the
AHB clock.
- #address-cells: Number of cells required to define a chip select
address on the SPI bus. Should be set to 1.
- #size-cells: Should be zero.
Optional properties:
- spi-max-frequency: Specifies maximum SPI clock frequency,
Units - Hz. Definition as per
Documentation/devicetree/bindings/spi/spi-bus.txt
- num-cs: total number of chipselects
- cs-gpios: should specify GPIOs used for chipselects.
The gpios will be referred to as reg = <index> in the SPI child
nodes. If unspecified, a single SPI device without a chip
select can be used.
SPI slave nodes must be children of the SPI master node and can contain
properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
Example:
spi_8: spi@f9964000 { /* BLSP2 QUP2 */
compatible = "qcom,spi-qup-v2";
#address-cells = <1>;
#size-cells = <0>;
reg = <0xf9964000 0x1000>;
interrupts = <0 102 0>;
spi-max-frequency = <19200000>;
clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
clock-names = "core", "iface";
pinctrl-names = "default";
pinctrl-0 = <&spi8_default>;
device@0 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <0>; /* Chip select 0 */
spi-max-frequency = <19200000>;
spi-cpol;
};
device@1 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <1>; /* Chip select 1 */
spi-max-frequency = <9600000>;
spi-cpha;
};
device@2 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <2>; /* Chip select 2 */
spi-max-frequency = <19200000>;
spi-cpol;
spi-cpha;
};
device@3 {
compatible = "arm,pl022-dummy";
#address-cells = <1>;
#size-cells = <1>;
reg = <3>; /* Chip select 3 */
spi-max-frequency = <19200000>;
spi-cpol;
spi-cpha;
spi-cs-high;
};
};
|
