| Age | Commit message (Collapse) | Author |
|---|
|
dp_ctrl_off_link() was created to handle a case where we received
a cable connect and then get a cable disconnect without the corresponding
dp_display_enable(). For such cases the pixel clock will be off but the
link clock will still be on. dp_ctrl_off_link() handles this case by
turning off the link clock only.
However, the vote removal to the opp table for this case was missed.
Remove the opp table vote in dp_ctrl_off_link().
Fixes: 375a126090b9 ("drm/msm/dp: tear down main link at unplug handle immediately")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/627487/
Link: https://lore.kernel.org/r/20241205-dp_mst-v1-2-f8618d42a99a@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
dp_ctrl_configure_source_params()
Once the link has already been setup there is no need to call
dp_catalog_ctrl_mainlink_ctrl() as this does a reset on the mainlink
thereby tearing down the link briefly.
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/627479/
Link: https://lore.kernel.org/r/20241205-dp_mst-v1-1-f8618d42a99a@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
For historical reasons a lot of symbols in the MSM DisplayPort driver
used the generic dp_ prefix. Perform a mass-rename of those symbols to
use msm_dp prefix.
Basically this is a result of the following script:
sed drivers/gpu/drm/msm/dp/* -i -e 's/\<dp_/msm_dp_/g'
sed drivers/gpu/drm/msm/dp/* -i -e 's/"msm_dp_/"dp_/g'
sed drivers/gpu/drm/msm/dp/* -i -e 's/msm_\(dp_sdp_header\|dp_sdp\)\>/\1/g'
Yes, this also results in renaming of several struct fields in addition
to renaming the structs and functions, but I think the simple solution
is better than the more complex one.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410250305.UHKDhtxy-lkp@intel.com/
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/622211/
Link: https://lore.kernel.org/r/20241029-msm-dp-rename-v2-1-13c5c03fad44@linaro.org
|
|
Before re-starting link training reset the link phy params namely
the pre-emphasis and voltage swing levels otherwise the next
link training begins at the previously cached levels which can result
in link training failures.
Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/605946/
Link: https://lore.kernel.org/r/20240725220450.131245-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
The "desc" member of struct dp_panel is zero-initialized during
allocation and never assigned, resulting in dp_ctrl_use_fixed_nvid()
never returning true. This returned boolean value is passed around but
never acted upon.
Perform constant propagation and remove the traces of "fixed nvid".
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/585344/
Link: https://lore.kernel.org/r/20240328-msm-dp-cleanup-v2-2-a5aed9798d32@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Both dp_link_adjust_levels() and dp_ctrl_update_vx_px() limit swing and
pre-emphasis to 2, while the real maximum value for the sum of the
voltage swing and pre-emphasis is 3. Fix the DP code to remove this
limitation.
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/577006/
Link: https://lore.kernel.org/r/20240203-dp-swing-3-v1-1-6545e1706196@linaro.org
|
|
DP controller can be setup to operate in either SDP update flush mode or
peripheral flush mode based on the DP controller hardware version.
Starting in DP v1.2, the hardware documents require the use of
peripheral flush mode for SDP packets such as PPS OR VSC SDP packets.
In-line with this guidance, lets program the DP controller to use
peripheral flush mode starting DP v1.2
Changes in v4:
- Clear up that DP_MAINLINK_CTRL_FLUSH_MODE register requires
the use of bits [24:23]
- Modify macros DP_MAINLINK_FLUSH_MODE_UPDATE_SDP and
DP_MAINLINK_FLUSH_MODE_SDP_PERIPH_UPDATE to explicitly set
their values in the bits of DP_MAINLINK_CTRL_FLUSH_MODE_MASK
Changes in v3:
- Clear up that the DP_MAINLINK_FLUSH_MODE_SDE_PERIPH_UPDATE
macro is setting bits [24:23] to a value of 3
Changes in v2:
- Use the original dp_catalog_hw_revision() function to
correctly check the DP HW version
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579621/
Link: https://lore.kernel.org/r/20240222194025.25329-16-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Add support to pack and send the VSC SDP packet for DP. This therefore
allows the transmision of format information to the sinks which is
needed for YUV420 support over DP.
Changes in v5:
- Slightly modify use of drm_dp_vsc_sdp_pack()
- Remove dp_catalog NULL checks
- Modify dp_utils_pack_sdp_header() to more clearly pack the
header buffer
- Move dp_utils_pack_sdp_header() inside of
dp_catalog_panel_send_vsc_sdp to clearly show the relationship
between the header buffer and the vsc_sdp struct
- Due to the last point, remove the dp_utils_pack_vsc_sdp()
function and only call drm_dp_vsc_sdp_pack() in
dp_panel_setup_vsc_sdp_yuv_420()
Changes in v4:
- Remove struct msm_dp_sdp_with_parity
- Use dp_utils_pack_sdp_header() to pack the SDP header and
parity bytes into a buffer
- Use this buffer when writing the VSC SDP data in
dp_catalog_panel_send_vsc_sdp()
- Write to all of the MMSS_DP_GENERIC0 registers instead of just
the ones with non-zero values
Changes in v3:
- Create a new struct, msm_dp_sdp_with_parity, which holds the
packing information for VSC SDP
- Use drm_dp_vsc_sdp_pack() to pack the data into the new
msm_dp_sdp_with_parity struct instead of specifically packing
for YUV420 format
- Modify dp_catalog_panel_send_vsc_sdp() to send the VSC SDP
data using the new msm_dp_sdp_with_parity struct
Changes in v2:
- Rename GENERIC0_SDPSIZE macro to GENERIC0_SDPSIZE_VALID
- Remove dp_sdp from the dp_catalog struct since this data is
being allocated at the point used
- Create a new function in dp_utils to pack the VSC SDP data
into a buffer
- Create a new function that packs the SDP header bytes into a
buffer. This function is made generic so that it can be
utilized by dp_audio
header bytes into a buffer
- Create a new function in dp_utils that takes the packed buffer
and writes to the DP_GENERIC0_* registers
- Split the dp_catalog_panel_config_vsc_sdp() function into two
to disable/enable sending VSC SDP packets
- Check the DP HW version using the original useage of
dp_catalog_hw_revision() and correct the version checking
logic
- Rename dp_panel_setup_vsc_sdp() to
dp_panel_setup_vsc_sdp_yuv_420() to explicitly state that
currently VSC SDP is only being set up to support YUV420 modes
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579636/
Link: https://lore.kernel.org/r/20240222194025.25329-14-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Change all relevant DP controller related programming for YUV420 cases.
Namely, change the pixel clock math to consider YUV420 and modify the
MVID programming to consider YUV420.
Changes in v2:
- Move configuration control programming to a different commit
- Slight code simplification
- Add VSC SDP check when doing mode_pclk_khz division in
dp_bridge_mode_valid
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579640/
Link: https://lore.kernel.org/r/20240222194025.25329-12-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Change relevant DP controller related programming for YUV420 cases.
Program the configuration control register to indicate YUV420.
Changes in v2:
- Create a new patch only for configuration control programming
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579615/
Link: https://lore.kernel.org/r/20240222194025.25329-11-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
There is a spelling mistake in a drm_dbg_dp message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/577760/
Link: https://lore.kernel.org/r/20240212091639.2397424-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
There is little point in going trough dp_parser->io indirection each
time the driver needs to access the PHY. Store the pointer directly in
dp_ctrl_private.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576119/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-11-098d5f581dd3@linaro.org
|
|
There is little point in sharing phy configuration structure between
several modules. Move it to dp_ctrl, which becomes the only submodule
re-configuring the PHY.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576124/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-9-098d5f581dd3@linaro.org
|
|
Split the dp_ctrl_clk_enable() beast into four functions, each of them
doing just a single item: enabling or disabling core or link clocks.
This allows us to cleanup the dss_module_power structure and makes
several dp_ctrl functions return void.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576105/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-8-098d5f581dd3@linaro.org
|
|
All supported platforms use the same clocks configuration. Instead of
parsing names from DT in a pretty complex manner, use the static
configuration. If at some point newer (or older) platforms have
different clock configuration, this clock config can be moved to the
device data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576115/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-7-098d5f581dd3@linaro.org
|
|
There is only a single DP_STREAM_PM clock, stream_pixel. Instead of
using a separate dss_module_power instance for this single clock, handle
this clock directly. This allows us to drop several wrapping functions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576102/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-6-098d5f581dd3@linaro.org
|
|
The dp_power submodule is limited to handling the clocks only following
previous cleanups. Fold it into the dp_ctrl submodule, removing one
unnecessary level of indirection.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/576104/
Link: https://lore.kernel.org/r/20240126-dp-power-parser-cleanup-v3-5-098d5f581dd3@linaro.org
|
|
Since the value of DP_TEST_BIT_DEPTH_8 is already left shifted, in the
BPC unknown case, the additional shift causes spill over to the other
bits of the [DP_CONFIGURATION_CTRL] register.
Fix this by changing the return value of dp_link_get_test_bits_depth()
in the BPC unknown case to (DP_TEST_BIT_DEPTH_8 >> DP_TEST_BIT_DEPTH_SHIFT).
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/573989/
Link: https://lore.kernel.org/r/1704917931-30133-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: fix minor checkpatch warning to align with opening braces]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
DP PHY re-initialization done using dp_ctrl_reinitialize_mainlink() will
cause PLL unlocked initially and then PLL gets locked at the end of
initialization. PLL_UNLOCKED interrupt will fire during this time if the
interrupt mask is enabled.
However currently DP driver link training implementation incorrectly
re-initializes PHY unconditionally during link training as the PHY was
already configured in dp_ctrl_enable_mainlink_clocks().
Fix this by re-initializing the PHY only if the previous link training
failed.
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/30
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/551847/
Link: https://lore.kernel.org/r/1691533190-19335-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: added line break in commit text]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
If our interrupt handler gets called and we don't really handle the
interrupt then we should return IRQ_NONE. The current interrupt
handler didn't do this, so let's fix it.
NOTE: for some of the cases it's clear that we should return IRQ_NONE
and some cases it's clear that we should return IRQ_HANDLED. However,
there are a few that fall somewhere in between. Specifically, the
documentation for when to return IRQ_NONE vs. IRQ_HANDLED is probably
best spelled out in the commit message of commit d9e4ad5badf4 ("Document
that IRQ_NONE should be returned when IRQ not actually handled"). That
commit makes it clear that we should return IRQ_HANDLED if we've done
something to make the interrupt stop happening.
The case where it's unclear is, for instance, in dp_aux_isr() after
we've read the interrupt using dp_catalog_aux_get_irq() and confirmed
that "isr" is non-zero. The function dp_catalog_aux_get_irq() not only
reads the interrupts but it also "ack"s all the interrupts that are
returned. For an "unknown" interrupt this has a very good chance of
actually stopping the interrupt from happening. That would mean we've
identified that it's our device and done something to stop them from
happening and should return IRQ_HANDLED. Specifically, it should be
noted that most interrupts that need "ack"ing are ones that are
one-time events and doing an "ack" is enough to clear them. However,
since these interrupts are unknown then, by definition, it's unknown
if "ack"ing them is truly enough to clear them. It's possible that we
also need to remove the original source of the interrupt. In this
case, IRQ_NONE would be a better choice.
Given that returning an occasional IRQ_NONE isn't the absolute end of
the world, however, let's choose that course of action. The IRQ
framework will forgive a few IRQ_NONE returns now and again (and it
won't even log them, which is why we have to log them ourselves). This
means that if we _do_ end hitting an interrupt where "ack"ing isn't
enough the kernel will eventually detect the problem and shut our
device down.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520660/
Link: https://lore.kernel.org/r/20230126170745.v2.2.I2d7aec2fadb9c237cd0090a47d6a8ba2054bf0f8@changeid
[DB: reformatted commit message to make checkpatch happy]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Add support for basic panel self refresh (PSR) feature for eDP.
Add a new interface to set PSR state in the sink from DPU.
Program the eDP controller to issue PSR enter and exit SDP to
the sink.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524734/
Link: https://lore.kernel.org/r/1677774797-31063-10-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.
Changes in v2:
1) fix spelling at commit text
2) merge ssc variable into encoding[0]
Changes in v3:
-- correct spelling of DOWNSPREAD_CTRL
-- replace err with len of ssize_t
Changes in v4:
-- split into 2 patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Patchwork: https://patchwork.freedesktop.org/patch/502532/
Link: https://lore.kernel.org/r/1662999830-13916-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
This API isn't really more than a couple lines now that we don't store
the pixel_rate to the struct member. Inline it into the caller.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490775/
Link: https://lore.kernel.org/r/20220623002540.871994-4-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This struct member is stored to in the function that calls the function
which uses it. That's possible with a function argument instead of
storing to a struct member. Pass the pixel_rate as an argument instead
to simplify the code. Note that dp_ctrl_link_maintenance() was storing
the pixel_rate but never using it so we just remove the assignment from
there.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490772/
Link: https://lore.kernel.org/r/20220623002540.871994-3-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Let's move these functions around to avoid having to forward declare
dp_ctrl_on_stream_phy_test_report(). Also remove
dp_ctrl_reinitialize_mainlink() forward declaration because we're doing
that sort of task.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/490771/
Link: https://lore.kernel.org/r/20220623002540.871994-2-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Data Symbols scrambled is required for tps4 at link training 2.
Therefore SCRAMBLING_DISABLE bit should not be set for tps4 to
work.
RECOVERED_CLOCK_OUT_EN is for enable simple EYE test for jitter
measurement with minimal equipment for embedded applications purpose
and is not required to be set during normal operation. Current
implementation always have RECOVERED_CLOCK_OUT_EN bit set which
cause SCRAMBLING_DISABLE bit wrongly set at tps4 which prevent
tps4 from working.
This patch delete setting RECOVERED_CLOCK_OUT_EN to fix
SCRAMBLING_DISABLE be wrongly set at tps4.
Changes in v2:
-- fix Fixes tag
Changes in v3:
-- revise commit text
Changes in v4:
-- fix commit text newline
Changes in v5:
-- fix commit text line over 75 chars
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/497194/
Link: https://lore.kernel.org/r/1660258670-4200-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
In order to simplify DP code, drop hand-coded loops over clock arrays,
replacing them with clk_bulk_* functions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474717/
Link: https://lore.kernel.org/r/20220217055529.499829-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The only clock for which we set the rate is the "stream_pixel". Rather
than storing the rate and then setting it by looping over all the
clocks, set the clock rate directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474714/
Link: https://lore.kernel.org/r/20220217055529.499829-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
"ctrl_link" is the clock from DP_CTRL_PM module. The result of setting
the rate for it would be a call to dev_pm_opp_set_rate(). Instead of
saving the rate inside struct dss_module_power, call the
devm_pm_opp_set_rate() directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474712/
Link: https://lore.kernel.org/r/20220217055529.499829-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Merge v5.19 fixes to avoid merge conflicts
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Display resolution change is implemented through drm modeset. Older
modeset (resolution) has to be disabled first before newer modeset
(resolution) can be enabled. Display disable will turn off both
pixel clock and main link clock so that main link have to be
re-trained during display enable to have new video stream flow
again. At current implementation, display enable function manually
kicks up irq_hpd_handle which will read panel link status and start
link training if link status is not in sync state.
However, there is rare case that a particular panel links status keep
staying in sync for some period of time after main link had been shut
down previously at display disabled. In this case, main link retraining
will not be executed by irq_hdp_handle(). Hence video stream of newer
display resolution will fail to be transmitted to panel due to main
link is not in sync between host and panel.
This patch will bypass irq_hpd_handle() in favor of directly call
dp_ctrl_on_stream() to always perform link training in regardless of
main link status. So that no unexpected exception resolution change
failure cases will happen. Also this implementation are more efficient
than manual kicking off irq_hpd_handle function.
Changes in v2:
-- set force_link_train flag on DP only (is_edp == false)
Changes in v3:
-- revise commit text
-- add Fixes tag
Changes in v4:
-- revise commit text
Changes in v5:
-- fix spelling at commit text
Changes in v6:
-- split dp_ctrl_on_stream() for phy test case
-- revise commit text for modeset
Changes in v7:
-- drop 0 assignment at local variable (ret = 0)
Changes in v8:
-- add patch to remove pixel_rate from dp_ctrl
Changes in v9:
-- forward declare dp_ctrl_on_stream_phy_test_report()
Fixes: 62671d2ef24b ("drm/msm/dp: fixes wrong connection state caused by failure of link train")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/489895/
Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
https://gitlab.freedesktop.org/abhinavk/msm into drm-next
5.19 fixes for msm-next
- Fix to add minimum ICC vote in the msm_mdss pm_resume path to address
bootup splats
- Fix to avoid dereferencing without checking in WB encoder
- Fix to avoid crash during suspend in DP driver by ensuring interrupt
mask bits are updated
- Remove unused code from dpu_encoder_virt_atomic_check()
- Fix to remove redundant init of dsc variable
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/927b201e-a734-a29d-b9fb-b9889e1f7795@quicinc.com
|
|
dp_ctrl_reset_irq_ctrl()
dp_catalog_ctrl_reset() will software reset DP controller. But it will
not reset programmable registers to default value. DP driver still have
to clear mask bits to interrupt status registers to disable interrupts
after software reset of controller.
At current implementation, dp_ctrl_reset_irq_ctrl() will software reset dp
controller but did not call dp_catalog_ctrl_enable_irq(false) to clear hpd
related interrupt mask bits to disable hpd related interrupts due to it
mistakenly think hpd related interrupt mask bits will be cleared by software
reset of dp controller automatically. This mistake may cause system to crash
during suspending procedure due to unexpected irq fired and trigger event
thread to access dp controller registers with controller clocks are disabled.
This patch fixes system crash during suspending problem by removing "enable"
flag condition checking at dp_ctrl_reset_irq_ctrl() so that hpd related
interrupt mask bits are cleared to prevent unexpected from happening.
Changes in v2:
-- add more details commit text
Changes in v3:
-- add synchrons_irq()
-- add atomic_t suspended
Changes in v4:
-- correct Fixes's commit ID
-- remove synchrons_irq()
Changes in v5:
-- revise commit text
Changes in v6:
-- add event_lock to protect "suspended"
Changes in v7:
-- delete "suspended" flag
Fixes: 989ebe7bc446 ("drm/msm/dp: do not initialize phy until plugin interrupt received")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/486591/
Link: https://lore.kernel.org/r/1652804494-19650-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
- Fourcc modifier for tiled but not compressed layouts
- Support for userspace allocated IOVA (GPU virtual address)
- Devfreq clamp_to_idle fix
- DPU: DSC (Display Stream Compression) support
- DPU: inline rotation support on SC7280
- DPU: update DP timings to follow vendor recommendations
- DP, DPU: add support for wide bus (on newer chipsets)
- DP: eDP support
- Merge DPU1 and MDP5 MDSS driver, make dpu/mdp device the master
component
- MDSS: optionally reset the IP block at the bootup to drop
bootloader state
- Properly register and unregister internal bridges in the DRM framework
- Complete DPU IRQ cleanup
- DP: conversion to use drm_bridge and drm_bridge_connector
- eDP: drop old eDP parts again
- DPU: writeback support
- Misc small fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvJCr_1D8d0dgmyQC5HD4gmXeZw=bFV_CNCfceZbpMxRw@mail.gmail.com
|
|
compliance test
At normal operation, transmit phy test pattern has to be terminated before
DP controller switch to video ready state. However during phy compliance
testing, transmit phy test pattern should not be terminated until end of
compliance test which usually indicated by unplugged interrupt.
Only stop sending the train pattern in dp_ctrl_on_stream() if we're not
doing compliance testing. We also no longer reset 'p_level' and
'v_level' within dp_ctrl_on_link() due to both 'p_level' and 'v_level'
are acquired from link status at previous dpcd read and we like to use
those level to start link training.
Changes in v2:
-- add more details commit text
-- correct Fixes
Changes in v3:
-- drop unnecessary braces
Fixes: 2e0adc765d88 ("drm/msm/dp: do not end dp link training until video is ready")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483564/
Link: https://lore.kernel.org/r/1650995939-28467-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
DP controller state can not switch from video ready state to
transmit phy pattern state at run time. DP mainlink has to be
teared down followed by reset controller to default state to have
DP controller switch to transmit phy test pattern state and start
generate specified phy test pattern to sinker once main link setup
again.
Changes in v2:
-- correct Fixes's commit id
Fixes: 52352fe2f866 ("drm/msm/dp: use dp_ctrl_off_link_stream during PHY compliance test run")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483563/
Link: https://lore.kernel.org/r/1650995939-28467-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Two stages are required to setup up main link to be ready to transmit
video stream.
Stage 1: dp_hpd_plug_handle() perform link training to set up main link
stage 2: user space framework (msm_dp_display_enable()) to enable pixel
clock and transfer main link to video ready state.
At current implementation, when dongle unplugged dp_hdp_unplug_handle()
has to wait until stage 2 completed before it can send link down uevent
to user space framework to disable pixel clock followed by tearing down
main link. This introduce unnecessary latency if dongle unplugged happen
after stage 1 and before stage 2. It also has possibility leave main link
stay at ready state after dongle unplugged if framework does not response
to link down uevent notification. This will prevent next dongle plug in
from working. This scenario could possibly happen when dongle unplug while
system in the middle of suspending.
This patch allow unplug handle to tear down main link and notify
framework link down immediately if dongle unplugged happen after
stage 1 and before stage 2. With this approach, dp driver is much
more resilient to any different scenarios. Also redundant both
dp_connect_pending_timeout() and dp_disconnect_pending_timeout()
are removed to reduce logic complexity.
Changes in V2:
-- return -EINVAL at msm_dp_display_enable() if not in correct state
-- replace ST_CONNECT_PENDING with ST_MAINLINK_READY
Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483391/
Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com
[DB: fixed return values due to conversion to function merge]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Since DRM_DEBUG_DP is deprecated in favor of drm_dbg_dp(NULL, ...),
this patch replace all DRM_DEBUG_DP with drm_dbg_dp().
Changes in v4:
-- replace (strucr drm_dev *)NULL with drm_dev
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/474870/
Link: https://lore.kernel.org/r/1645122930-23863-4-git-send-email-quic_khsieh@quicinc.com
[DB: fixed compilation of dp_bridge_detect() caused by previous patch]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
We're experimenting a bit with the process this time, with Dmitry
collecting display patches and merging them into msm-next with me
handling the gpu/etc side of things. Summary of interesting new bits
and pieces
* dpu + dp support for sc8180x
* dp support for sm8350
* dpu + dsi support for qcm2290
* 10nm dsi phy tuning support
* bridge support for dp encoder
* gpu support for additional 7c3 SKUs
* assorted cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGu=Jdrw6DqYOYPTMks7=zatrsvdR=o6DpjqZ=TQQhFZuw@mail.gmail.com
|
|
DP phy should be initialized and exited symmetrically to avoid
clock being stucked at either on or off error. Add debug info
to cover all DP phy to identify clock issues easily.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1643828199-8564-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Each DP link training contains link training 1 followed by link
training 2. There is maximum of 5 retries of DP link training
before declared link training failed. It is required to stop link
training at end of link training 2 if it is failed so that next
link training 1 can start freshly. This patch fixes link compliance
test case 4.3.1.13 (Source Device Link Training EQ Fallback Test).
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Fixes: 2e0adc765d88 ("drm/msm/dp: do not end dp link training until video is ready")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-5-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Some DP sinkers prefer to use tps4 instead of tps3 during training #2.
This patch will use tps4 to perform link training #2 if sinker's DPCD
supports it.
Changes in V2:
-- replace dp_catalog_ctrl_set_pattern() with dp_catalog_ctrl_set_pattern_state_bit()
Changes in V3:
-- change state_ctrl_bits type to u32 and pattern type to u8
Changes in V4:
-- align } else if { and } else {
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Current DP drivers have regulators, clocks, irq and phy are grouped
together within a function and executed not in a symmetric manner.
This increase difficulty of code maintenance and limited code scalability.
This patch divides the driver life cycle of operation into four states,
resume (including booting up), dongle plugin, dongle unplugged and suspend.
Regulators, core clocks and irq are grouped together and enabled at resume
(or booting up) so that the DP controller is armed and ready to receive HPD
plugin interrupts. HPD plugin interrupt is generated when a dongle plugs
into DUT (device under test). Once HPD plugin interrupt is received, DP
controller will initialize phy so that dpcd read/write will function and
following link training can be proceeded successfully. DP phy will be
disabled after main link is teared down at end of unplugged HPD interrupt
handle triggered by dongle unplugged out of DUT. Finally regulators, code
clocks and irq are disabled at corresponding suspension.
Changes in V2:
-- removed unnecessary dp_ctrl NULL check
-- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs
-- remove flip parameter out of dp_ctrl_irq_enable()
-- add fixes tag
Changes in V3:
-- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at
dp_display_host_init() for eDP
Changes in V4:
-- rewording commit text to match this commit changes
Changes in V5:
-- rebase on top of msm-next branch
Changes in V6:
-- delete flip variable
Changes in V7:
-- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl()
Changes in V8:
-- add more detail comment regrading dp phy at dp_display_host_init()
Changes in V9:
-- remove set phy_initialized to false when -ECONNRESET detected
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately
if aux read
Changes in v12:
-- move dp_display_host_phy_exit() after dp_display_host_deinit()
Changes in v13:
-- do not execute phy_init until plugged_in interrupt for edp, same as DP.
Changes in v14:
-- remove redundant dp->core_initialized = false form dp_pm_suspend.
Changes in v15:
-- remove core_initialized flag check at both host_init and host_deinit
Changes in v16:
-- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend
Changes in v17:
-- remove core_initialized checking before execute attention_cb()
Changes in v18:
-- remove core_initialized checking at dp_pm_suspend
Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
[airlied: add two missing Kconfig]
drm-misc-next for v5.18:
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/456a23c6-7324-7543-0c45-751f30ef83f7@linux.intel.com
|
|
Move all public DisplayPort headers into dp/ and update users. No
functional changes.
v3:
* rebased onto latest drm-tip
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-5-tzimmermann@suse.de
|
|
The eDP sink on sc7280 supports ASSR and dp driver will
enable ASSR in the source hardware. The driver needs to
enable the ASSR field in the DPCD configuration register
to avoid screen corruption. This change will enable ASSR
if supported in the sink device.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1635839325-401-6-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The sc7280 eDP sink that supports downspread will fail link training
if source does not enable SSC / downspread. This change will set the
downspread bit in the DP sink if supported and indicate SSC support
to the DP PHY driver.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1635839325-401-5-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Initialize both pre-emphasis and voltage swing level to 0 before
start link training and do not end link training until video is
ready to reduce the period between end of link training and video
start to meet Link Layer CTS requirement. Some dongle main link
symbol may become unlocked again if host did not end link training
soon enough after completion of link training 2. Host have to re
train main link if loss of symbol locked detected before end link
training so that the coming video stream can be transmitted to sink
properly. This fixes Link Layer CTS cases 4.3.2.1, 4.3.2.2, 4.3.2.3
and 4.3.2.4.
Changes in v3:
-- merge retrain link if loss of symbol locked happen into this patch
-- replace dp_ctrl_loss_symbol_lock() with dp_ctrl_channel_eq_ok()
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-7-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
