diff options
Diffstat (limited to 'drivers/spi/atmel-quadspi.c')
| -rw-r--r-- | drivers/spi/atmel-quadspi.c | 984 |
1 files changed, 898 insertions, 86 deletions
diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c index 316bce577081..244ac0106862 100644 --- a/drivers/spi/atmel-quadspi.c +++ b/drivers/spi/atmel-quadspi.c @@ -11,11 +11,15 @@ * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale. */ +#include <linux/bitfield.h> #include <linux/clk.h> #include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> #include <linux/err.h> #include <linux/interrupt.h> #include <linux/io.h> +#include <linux/iopoll.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/of.h> @@ -34,6 +38,7 @@ #define QSPI_IDR 0x0018 /* Interrupt Disable Register */ #define QSPI_IMR 0x001c /* Interrupt Mask Register */ #define QSPI_SCR 0x0020 /* Serial Clock Register */ +#define QSPI_SR2 0x0024 /* SAMA7G5 Status Register */ #define QSPI_IAR 0x0030 /* Instruction Address Register */ #define QSPI_ICR 0x0034 /* Instruction Code Register */ @@ -44,16 +49,32 @@ #define QSPI_SMR 0x0040 /* Scrambling Mode Register */ #define QSPI_SKR 0x0044 /* Scrambling Key Register */ +#define QSPI_REFRESH 0x0050 /* Refresh Register */ +#define QSPI_WRACNT 0x0054 /* Write Access Counter Register */ +#define QSPI_DLLCFG 0x0058 /* DLL Configuration Register */ +#define QSPI_PCALCFG 0x005C /* Pad Calibration Configuration Register */ +#define QSPI_PCALBP 0x0060 /* Pad Calibration Bypass Register */ +#define QSPI_TOUT 0x0064 /* Timeout Register */ + #define QSPI_WPMR 0x00E4 /* Write Protection Mode Register */ #define QSPI_WPSR 0x00E8 /* Write Protection Status Register */ #define QSPI_VERSION 0x00FC /* Version Register */ +#define SAMA7G5_QSPI0_MAX_SPEED_HZ 200000000 +#define SAMA7G5_QSPI1_SDR_MAX_SPEED_HZ 133000000 /* Bitfields in QSPI_CR (Control Register) */ #define QSPI_CR_QSPIEN BIT(0) #define QSPI_CR_QSPIDIS BIT(1) +#define QSPI_CR_DLLON BIT(2) +#define QSPI_CR_DLLOFF BIT(3) +#define QSPI_CR_STPCAL BIT(4) +#define QSPI_CR_SRFRSH BIT(5) #define QSPI_CR_SWRST BIT(7) +#define QSPI_CR_UPDCFG BIT(8) +#define QSPI_CR_STTFR BIT(9) +#define QSPI_CR_RTOUT BIT(10) #define QSPI_CR_LASTXFER BIT(24) /* Bitfields in QSPI_MR (Mode Register) */ @@ -61,12 +82,14 @@ #define QSPI_MR_LLB BIT(1) #define QSPI_MR_WDRBT BIT(2) #define QSPI_MR_SMRM BIT(3) +#define QSPI_MR_DQSDLYEN BIT(3) #define QSPI_MR_CSMODE_MASK GENMASK(5, 4) #define QSPI_MR_CSMODE_NOT_RELOADED (0 << 4) #define QSPI_MR_CSMODE_LASTXFER (1 << 4) #define QSPI_MR_CSMODE_SYSTEMATICALLY (2 << 4) #define QSPI_MR_NBBITS_MASK GENMASK(11, 8) #define QSPI_MR_NBBITS(n) ((((n) - 8) << 8) & QSPI_MR_NBBITS_MASK) +#define QSPI_MR_OENSD BIT(15) #define QSPI_MR_DLYBCT_MASK GENMASK(23, 16) #define QSPI_MR_DLYBCT(n) (((n) << 16) & QSPI_MR_DLYBCT_MASK) #define QSPI_MR_DLYCS_MASK GENMASK(31, 24) @@ -80,6 +103,13 @@ #define QSPI_SR_CSR BIT(8) #define QSPI_SR_CSS BIT(9) #define QSPI_SR_INSTRE BIT(10) +#define QSPI_SR_LWRA BIT(11) +#define QSPI_SR_QITF BIT(12) +#define QSPI_SR_QITR BIT(13) +#define QSPI_SR_CSFA BIT(14) +#define QSPI_SR_CSRA BIT(15) +#define QSPI_SR_RFRSHD BIT(16) +#define QSPI_SR_TOUT BIT(17) #define QSPI_SR_QSPIENS BIT(24) #define QSPI_SR_CMD_COMPLETED (QSPI_SR_INSTRE | QSPI_SR_CSR) @@ -92,9 +122,22 @@ #define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) #define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) +/* Bitfields in QSPI_SR2 (SAMA7G5 Status Register) */ +#define QSPI_SR2_SYNCBSY BIT(0) +#define QSPI_SR2_QSPIENS BIT(1) +#define QSPI_SR2_CSS BIT(2) +#define QSPI_SR2_RBUSY BIT(3) +#define QSPI_SR2_HIDLE BIT(4) +#define QSPI_SR2_DLOCK BIT(5) +#define QSPI_SR2_CALBSY BIT(6) + +/* Bitfields in QSPI_IAR (Instruction Address Register) */ +#define QSPI_IAR_ADDR GENMASK(31, 0) + /* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */ #define QSPI_ICR_INST_MASK GENMASK(7, 0) #define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) +#define QSPI_ICR_INST_MASK_SAMA7G5 GENMASK(15, 0) #define QSPI_ICR_OPT_MASK GENMASK(23, 16) #define QSPI_ICR_OPT(opt) (((opt) << 16) & QSPI_ICR_OPT_MASK) @@ -107,6 +150,9 @@ #define QSPI_IFR_WIDTH_QUAD_IO (4 << 0) #define QSPI_IFR_WIDTH_DUAL_CMD (5 << 0) #define QSPI_IFR_WIDTH_QUAD_CMD (6 << 0) +#define QSPI_IFR_WIDTH_OCT_OUTPUT (7 << 0) +#define QSPI_IFR_WIDTH_OCT_IO (8 << 0) +#define QSPI_IFR_WIDTH_OCT_CMD (9 << 0) #define QSPI_IFR_INSTEN BIT(4) #define QSPI_IFR_ADDREN BIT(5) #define QSPI_IFR_OPTEN BIT(6) @@ -117,19 +163,60 @@ #define QSPI_IFR_OPTL_4BIT (2 << 8) #define QSPI_IFR_OPTL_8BIT (3 << 8) #define QSPI_IFR_ADDRL BIT(10) +#define QSPI_IFR_ADDRL_SAMA7G5 GENMASK(11, 10) #define QSPI_IFR_TFRTYP_MEM BIT(12) #define QSPI_IFR_SAMA5D2_WRITE_TRSFR BIT(13) #define QSPI_IFR_CRM BIT(14) +#define QSPI_IFR_DDREN BIT(15) #define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) #define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) +#define QSPI_IFR_END BIT(22) +#define QSPI_IFR_SMRM BIT(23) #define QSPI_IFR_APBTFRTYP_READ BIT(24) /* Defined in SAM9X60 */ +#define QSPI_IFR_DQSEN BIT(25) +#define QSPI_IFR_DDRCMDEN BIT(26) +#define QSPI_IFR_HFWBEN BIT(27) +#define QSPI_IFR_PROTTYP GENMASK(29, 28) +#define QSPI_IFR_PROTTYP_STD_SPI 0 +#define QSPI_IFR_PROTTYP_TWIN_QUAD 1 +#define QSPI_IFR_PROTTYP_OCTAFLASH 2 +#define QSPI_IFR_PROTTYP_HYPERFLASH 3 /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ #define QSPI_SMR_SCREN BIT(0) #define QSPI_SMR_RVDIS BIT(1) +#define QSPI_SMR_SCRKL BIT(2) + +/* Bitfields in QSPI_REFRESH (Refresh Register) */ +#define QSPI_REFRESH_DELAY_COUNTER GENMASK(31, 0) + +/* Bitfields in QSPI_WRACNT (Write Access Counter Register) */ +#define QSPI_WRACNT_NBWRA GENMASK(31, 0) + +/* Bitfields in QSPI_DLLCFG (DLL Configuration Register) */ +#define QSPI_DLLCFG_RANGE BIT(0) + +/* Bitfields in QSPI_PCALCFG (DLL Pad Calibration Configuration Register) */ +#define QSPI_PCALCFG_AAON BIT(0) +#define QSPI_PCALCFG_DAPCAL BIT(1) +#define QSPI_PCALCFG_DIFFPM BIT(2) +#define QSPI_PCALCFG_CLKDIV GENMASK(6, 4) +#define QSPI_PCALCFG_CALCNT GENMASK(16, 8) +#define QSPI_PCALCFG_CALP GENMASK(27, 24) +#define QSPI_PCALCFG_CALN GENMASK(31, 28) + +/* Bitfields in QSPI_PCALBP (DLL Pad Calibration Bypass Register) */ +#define QSPI_PCALBP_BPEN BIT(0) +#define QSPI_PCALBP_CALPBP GENMASK(11, 8) +#define QSPI_PCALBP_CALNBP GENMASK(19, 16) + +/* Bitfields in QSPI_TOUT (Timeout Register) */ +#define QSPI_TOUT_TCNTM GENMASK(15, 0) /* Bitfields in QSPI_WPMR (Write Protection Mode Register) */ #define QSPI_WPMR_WPEN BIT(0) +#define QSPI_WPMR_WPITEN BIT(1) +#define QSPI_WPMR_WPCREN BIT(2) #define QSPI_WPMR_WPKEY_MASK GENMASK(31, 8) #define QSPI_WPMR_WPKEY(wpkey) (((wpkey) << 8) & QSPI_WPMR_WPKEY_MASK) @@ -138,23 +225,74 @@ #define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8) #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) +#define ATMEL_QSPI_TIMEOUT 1000 /* ms */ +#define ATMEL_QSPI_SYNC_TIMEOUT 300 /* ms */ +#define QSPI_DLLCFG_THRESHOLD_FREQ 90000000U +#define QSPI_CALIB_TIME 2000 /* 2 us */ + +/* Use PIO for small transfers. */ +#define ATMEL_QSPI_DMA_MIN_BYTES 16 +/** + * struct atmel_qspi_pcal - Pad Calibration Clock Division + * @pclk_rate: peripheral clock rate. + * @pclk_div: calibration clock division. The clock applied to the calibration + * cell is divided by pclk_div + 1. + */ +struct atmel_qspi_pcal { + u32 pclk_rate; + u8 pclk_div; +}; + +#define ATMEL_QSPI_PCAL_ARRAY_SIZE 8 +static const struct atmel_qspi_pcal pcal[ATMEL_QSPI_PCAL_ARRAY_SIZE] = { + {25000000, 0}, + {50000000, 1}, + {75000000, 2}, + {100000000, 3}, + {125000000, 4}, + {150000000, 5}, + {175000000, 6}, + {200000000, 7}, +}; + struct atmel_qspi_caps { + u32 max_speed_hz; bool has_qspick; + bool has_gclk; bool has_ricr; + bool octal; + bool has_dma; }; +struct atmel_qspi_ops; + struct atmel_qspi { void __iomem *regs; void __iomem *mem; struct clk *pclk; struct clk *qspick; + struct clk *gclk; struct platform_device *pdev; const struct atmel_qspi_caps *caps; + const struct atmel_qspi_ops *ops; resource_size_t mmap_size; u32 pending; + u32 irq_mask; u32 mr; u32 scr; + u32 target_max_speed_hz; struct completion cmd_completion; + struct completion dma_completion; + dma_addr_t mmap_phys_base; + struct dma_chan *rx_chan; + struct dma_chan *tx_chan; +}; + +struct atmel_qspi_ops { + int (*set_cfg)(struct atmel_qspi *aq, const struct spi_mem_op *op, + u32 *offset); + int (*transfer)(struct spi_mem *mem, const struct spi_mem_op *op, + u32 offset); }; struct atmel_qspi_mode { @@ -174,6 +312,19 @@ static const struct atmel_qspi_mode atmel_qspi_modes[] = { { 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD }, }; +static const struct atmel_qspi_mode atmel_qspi_sama7g5_modes[] = { + { 1, 1, 1, QSPI_IFR_WIDTH_SINGLE_BIT_SPI }, + { 1, 1, 2, QSPI_IFR_WIDTH_DUAL_OUTPUT }, + { 1, 1, 4, QSPI_IFR_WIDTH_QUAD_OUTPUT }, + { 1, 2, 2, QSPI_IFR_WIDTH_DUAL_IO }, + { 1, 4, 4, QSPI_IFR_WIDTH_QUAD_IO }, + { 2, 2, 2, QSPI_IFR_WIDTH_DUAL_CMD }, + { 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD }, + { 1, 1, 8, QSPI_IFR_WIDTH_OCT_OUTPUT }, + { 1, 8, 8, QSPI_IFR_WIDTH_OCT_IO }, + { 8, 8, 8, QSPI_IFR_WIDTH_OCT_CMD }, +}; + #ifdef VERBOSE_DEBUG static const char *atmel_qspi_reg_name(u32 offset, char *tmp, size_t sz) { @@ -196,6 +347,8 @@ static const char *atmel_qspi_reg_name(u32 offset, char *tmp, size_t sz) return "IMR"; case QSPI_SCR: return "SCR"; + case QSPI_SR2: + return "SR2"; case QSPI_IAR: return "IAR"; case QSPI_ICR: @@ -208,6 +361,18 @@ static const char *atmel_qspi_reg_name(u32 offset, char *tmp, size_t sz) return "SMR"; case QSPI_SKR: return "SKR"; + case QSPI_REFRESH: + return "REFRESH"; + case QSPI_WRACNT: + return "WRACNT"; + case QSPI_DLLCFG: + return "DLLCFG"; + case QSPI_PCALCFG: + return "PCALCFG"; + case QSPI_PCALBP: + return "PCALBP"; + case QSPI_TOUT: + return "TOUT"; case QSPI_WPMR: return "WPMR"; case QSPI_WPSR: @@ -249,6 +414,28 @@ static void atmel_qspi_write(u32 value, struct atmel_qspi *aq, u32 offset) writel_relaxed(value, aq->regs + offset); } +static int atmel_qspi_reg_sync(struct atmel_qspi *aq) +{ + u32 val; + int ret; + + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_SYNCBSY), 40, + ATMEL_QSPI_SYNC_TIMEOUT); + return ret; +} + +static int atmel_qspi_update_config(struct atmel_qspi *aq) +{ + int ret; + + ret = atmel_qspi_reg_sync(aq); + if (ret) + return ret; + atmel_qspi_write(QSPI_CR_UPDCFG, aq, QSPI_CR); + return atmel_qspi_reg_sync(aq); +} + static inline bool atmel_qspi_is_compatible(const struct spi_mem_op *op, const struct atmel_qspi_mode *mode) { @@ -275,12 +462,31 @@ static int atmel_qspi_find_mode(const struct spi_mem_op *op) return -EOPNOTSUPP; } +static int atmel_qspi_sama7g5_find_mode(const struct spi_mem_op *op) +{ + u32 i; + + for (i = 0; i < ARRAY_SIZE(atmel_qspi_sama7g5_modes); i++) + if (atmel_qspi_is_compatible(op, &atmel_qspi_sama7g5_modes[i])) + return i; + + return -EOPNOTSUPP; +} + static bool atmel_qspi_supports_op(struct spi_mem *mem, const struct spi_mem_op *op) { + struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->controller); if (!spi_mem_default_supports_op(mem, op)) return false; + if (aq->caps->octal) { + if (atmel_qspi_sama7g5_find_mode(op) < 0) + return false; + else + return true; + } + if (atmel_qspi_find_mode(op) < 0) return false; @@ -292,6 +498,25 @@ static bool atmel_qspi_supports_op(struct spi_mem *mem, return true; } +/* + * If the QSPI controller is set in regular SPI mode, set it in + * Serial Memory Mode (SMM). + */ +static int atmel_qspi_set_serial_memory_mode(struct atmel_qspi *aq) +{ + int ret = 0; + + if (!(aq->mr & QSPI_MR_SMM)) { + aq->mr |= QSPI_MR_SMM; + atmel_qspi_write(aq->mr, aq, QSPI_MR); + + if (aq->caps->has_gclk) + ret = atmel_qspi_update_config(aq); + } + + return ret; +} + static int atmel_qspi_set_cfg(struct atmel_qspi *aq, const struct spi_mem_op *op, u32 *offset) { @@ -371,14 +596,9 @@ static int atmel_qspi_set_cfg(struct atmel_qspi *aq, ifr |= QSPI_IFR_TFRTYP_MEM; } - /* - * If the QSPI controller is set in regular SPI mode, set it in - * Serial Memory Mode (SMM). - */ - if (!(aq->mr & QSPI_MR_SMM)) { - aq->mr |= QSPI_MR_SMM; - atmel_qspi_write(aq->mr, aq, QSPI_MR); - } + mode = atmel_qspi_set_serial_memory_mode(aq); + if (mode < 0) + return mode; /* Clear pending interrupts */ (void)atmel_qspi_read(aq, QSPI_SR); @@ -404,10 +624,323 @@ static int atmel_qspi_set_cfg(struct atmel_qspi *aq, return 0; } +static int atmel_qspi_wait_for_completion(struct atmel_qspi *aq, u32 irq_mask) +{ + int err = 0; + u32 sr; + + /* Poll INSTRuction End status */ + sr = atmel_qspi_read(aq, QSPI_SR); + if ((sr & irq_mask) == irq_mask) + return 0; + + /* Wait for INSTRuction End interrupt */ + reinit_completion(&aq->cmd_completion); + aq->pending = sr & irq_mask; + aq->irq_mask = irq_mask; + atmel_qspi_write(irq_mask, aq, QSPI_IER); + if (!wait_for_completion_timeout(&aq->cmd_completion, + msecs_to_jiffies(ATMEL_QSPI_TIMEOUT))) + err = -ETIMEDOUT; + atmel_qspi_write(irq_mask, aq, QSPI_IDR); + + return err; +} + +static int atmel_qspi_transfer(struct spi_mem *mem, + const struct spi_mem_op *op, u32 offset) +{ + struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->controller); + + /* Skip to the final steps if there is no data */ + if (!op->data.nbytes) + return atmel_qspi_wait_for_completion(aq, + QSPI_SR_CMD_COMPLETED); + + /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */ + (void)atmel_qspi_read(aq, QSPI_IFR); + + /* Send/Receive data */ + if (op->data.dir == SPI_MEM_DATA_IN) { + memcpy_fromio(op->data.buf.in, aq->mem + offset, + op->data.nbytes); + + /* Synchronize AHB and APB accesses again */ + rmb(); + } else { + memcpy_toio(aq->mem + offset, op->data.buf.out, + op->data.nbytes); + + /* Synchronize AHB and APB accesses again */ + wmb(); + } + + /* Release the chip-select */ + atmel_qspi_write(QSPI_CR_LASTXFER, aq, QSPI_CR); + + return atmel_qspi_wait_for_completion(aq, QSPI_SR_CMD_COMPLETED); +} + +static int atmel_qspi_sama7g5_set_cfg(struct atmel_qspi *aq, + const struct spi_mem_op *op, u32 *offset) +{ + u32 iar, icr, ifr; + int mode, ret; + + iar = 0; + icr = FIELD_PREP(QSPI_ICR_INST_MASK_SAMA7G5, op->cmd.opcode); + ifr = QSPI_IFR_INSTEN; + + mode = atmel_qspi_sama7g5_find_mode(op); + if (mode < 0) + return mode; + ifr |= atmel_qspi_sama7g5_modes[mode].config; + + if (op->dummy.buswidth && op->dummy.nbytes) { + if (op->addr.dtr && op->dummy.dtr && op->data.dtr) + ifr |= QSPI_IFR_NBDUM(op->dummy.nbytes * 8 / + (2 * op->dummy.buswidth)); + else + ifr |= QSPI_IFR_NBDUM(op->dummy.nbytes * 8 / + op->dummy.buswidth); + } + + if (op->addr.buswidth && op->addr.nbytes) { + ifr |= FIELD_PREP(QSPI_IFR_ADDRL_SAMA7G5, op->addr.nbytes - 1) | + QSPI_IFR_ADDREN; + iar = FIELD_PREP(QSPI_IAR_ADDR, op->addr.val); + } + + if (op->addr.dtr && op->dummy.dtr && op->data.dtr) { + ifr |= QSPI_IFR_DDREN; + if (op->cmd.dtr) + ifr |= QSPI_IFR_DDRCMDEN; + + ifr |= QSPI_IFR_DQSEN; + } + + if (op->cmd.buswidth == 8 || op->addr.buswidth == 8 || + op->data.buswidth == 8) + ifr |= FIELD_PREP(QSPI_IFR_PROTTYP, QSPI_IFR_PROTTYP_OCTAFLASH); + + /* offset of the data access in the QSPI memory space */ + *offset = iar; + + /* Set data enable */ + if (op->data.nbytes) { + ifr |= QSPI_IFR_DATAEN; + + if (op->addr.nbytes) + ifr |= QSPI_IFR_TFRTYP_MEM; + } + + ret = atmel_qspi_set_serial_memory_mode(aq); + if (ret < 0) + return ret; + + /* Clear pending interrupts */ + (void)atmel_qspi_read(aq, QSPI_SR); + + /* Set QSPI Instruction Frame registers */ + if (op->addr.nbytes && !op->data.nbytes) + atmel_qspi_write(iar, aq, QSPI_IAR); + + if (op->data.dir == SPI_MEM_DATA_IN) { + atmel_qspi_write(icr, aq, QSPI_RICR); + } else { + atmel_qspi_write(icr, aq, QSPI_WICR); + if (op->data.nbytes) + atmel_qspi_write(FIELD_PREP(QSPI_WRACNT_NBWRA, + op->data.nbytes), + aq, QSPI_WRACNT); + } + + atmel_qspi_write(ifr, aq, QSPI_IFR); + + return atmel_qspi_update_config(aq); +} + +static void atmel_qspi_dma_callback(void *param) +{ + struct atmel_qspi *aq = param; + + complete(&aq->dma_completion); +} + +static int atmel_qspi_dma_xfer(struct atmel_qspi *aq, struct dma_chan *chan, + dma_addr_t dma_dst, dma_addr_t dma_src, + unsigned int len) +{ + struct dma_async_tx_descriptor *tx; + dma_cookie_t cookie; + int ret; + + tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!tx) { + dev_err(&aq->pdev->dev, "device_prep_dma_memcpy error\n"); + return -EIO; + } + + reinit_completion(&aq->dma_completion); + tx->callback = atmel_qspi_dma_callback; + tx->callback_param = aq; + cookie = tx->tx_submit(tx); + ret = dma_submit_error(cookie); + if (ret) { + dev_err(&aq->pdev->dev, "dma_submit_error %d\n", cookie); + return ret; + } + + dma_async_issue_pending(chan); + ret = wait_for_completion_timeout(&aq->dma_completion, + msecs_to_jiffies(20 * ATMEL_QSPI_TIMEOUT)); + if (ret == 0) { + dmaengine_terminate_sync(chan); + dev_err(&aq->pdev->dev, "DMA wait_for_completion_timeout\n"); + return -ETIMEDOUT; + } + + return 0; +} + +static int atmel_qspi_dma_rx_xfer(struct spi_mem *mem, + const struct spi_mem_op *op, + struct sg_table *sgt, loff_t loff) +{ + struct atmel_qspi *aq = + spi_controller_get_devdata(mem->spi->controller); + struct scatterlist *sg; + dma_addr_t dma_src; + unsigned int i, len; + int ret; + + dma_src = aq->mmap_phys_base + loff; + + for_each_sg(sgt->sgl, sg, sgt->nents, i) { + len = sg_dma_len(sg); + ret = atmel_qspi_dma_xfer(aq, aq->rx_chan, sg_dma_address(sg), + dma_src, len); + if (ret) + return ret; + dma_src += len; + } + + return 0; +} + +static int atmel_qspi_dma_tx_xfer(struct spi_mem *mem, + const struct spi_mem_op *op, + struct sg_table *sgt, loff_t loff) +{ + struct atmel_qspi *aq = + spi_controller_get_devdata(mem->spi->controller); + struct scatterlist *sg; + dma_addr_t dma_dst; + unsigned int i, len; + int ret; + + dma_dst = aq->mmap_phys_base + loff; + + for_each_sg(sgt->sgl, sg, sgt->nents, i) { + len = sg_dma_len(sg); + ret = atmel_qspi_dma_xfer(aq, aq->tx_chan, dma_dst, + sg_dma_address(sg), len); + if (ret) + return ret; + dma_dst += len; + } + + return 0; +} + +static int atmel_qspi_dma_transfer(struct spi_mem *mem, + const struct spi_mem_op *op, loff_t loff) +{ + struct sg_table sgt; + int ret; + + ret = spi_controller_dma_map_mem_op_data(mem->spi->controller, op, + &sgt); + if (ret) + return ret; + + if (op->data.dir == SPI_MEM_DATA_IN) + ret = atmel_qspi_dma_rx_xfer(mem, op, &sgt, loff); + else + ret = atmel_qspi_dma_tx_xfer(mem, op, &sgt, loff); + + spi_controller_dma_unmap_mem_op_data(mem->spi->controller, op, &sgt); + + return ret; +} + +static int atmel_qspi_sama7g5_transfer(struct spi_mem *mem, + const struct spi_mem_op *op, u32 offset) +{ + struct atmel_qspi *aq = + spi_controller_get_devdata(mem->spi->controller); + u32 val; + int ret; + + if (!op->data.nbytes) { + /* Start the transfer. */ + ret = atmel_qspi_reg_sync(aq); + if (ret) + return ret; + atmel_qspi_write(QSPI_CR_STTFR, aq, QSPI_CR); + + return atmel_qspi_wait_for_completion(aq, QSPI_SR_CSRA); + } + + /* Send/Receive data. */ + if (op->data.dir == SPI_MEM_DATA_IN) { + if (aq->rx_chan && op->addr.nbytes && + op->data.nbytes > ATMEL_QSPI_DMA_MIN_BYTES) { + ret = atmel_qspi_dma_transfer(mem, op, offset); + if (ret) + return ret; + } else { + memcpy_fromio(op->data.buf.in, aq->mem + offset, + op->data.nbytes); + } + + if (op->addr.nbytes) { + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_RBUSY), 40, + ATMEL_QSPI_SYNC_TIMEOUT); + if (ret) + return ret; + } + } else { + if (aq->tx_chan && op->addr.nbytes && + op->data.nbytes > ATMEL_QSPI_DMA_MIN_BYTES) { + ret = atmel_qspi_dma_transfer(mem, op, offset); + if (ret) + return ret; + } else { + memcpy_toio(aq->mem + offset, op->data.buf.out, + op->data.nbytes); + } + + ret = atmel_qspi_wait_for_completion(aq, QSPI_SR_LWRA); + if (ret) + return ret; + } + + /* Release the chip-select. */ + ret = atmel_qspi_reg_sync(aq); + if (ret) + return ret; + atmel_qspi_write(QSPI_CR_LASTXFER, aq, QSPI_CR); + + return atmel_qspi_wait_for_completion(aq, QSPI_SR_CSRA); +} + static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) { struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->controller); - u32 sr, offset; + u32 offset; int err; /* @@ -416,46 +949,20 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) * when the flash memories overrun the controller's memory space. */ if (op->addr.val + op->data.nbytes > aq->mmap_size) - return -ENOTSUPP; + return -EOPNOTSUPP; + + if (op->addr.nbytes > 4) + return -EOPNOTSUPP; err = pm_runtime_resume_and_get(&aq->pdev->dev); if (err < 0) return err; - err = atmel_qspi_set_cfg(aq, op, &offset); + err = aq->ops->set_cfg(aq, op, &offset); if (err) goto pm_runtime_put; - /* Skip to the final steps if there is no data */ - if (op->data.nbytes) { - /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */ - (void)atmel_qspi_read(aq, QSPI_IFR); - - /* Send/Receive data */ - if (op->data.dir == SPI_MEM_DATA_IN) - memcpy_fromio(op->data.buf.in, aq->mem + offset, - op->data.nbytes); - else - memcpy_toio(aq->mem + offset, op->data.buf.out, - op->data.nbytes); - - /* Release the chip-select */ - atmel_qspi_write(QSPI_CR_LASTXFER, aq, QSPI_CR); - } - - /* Poll INSTRuction End status */ - sr = atmel_qspi_read(aq, QSPI_SR); - if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) - goto pm_runtime_put; - - /* Wait for INSTRuction End interrupt */ - reinit_completion(&aq->cmd_completion); - aq->pending = sr & QSPI_SR_CMD_COMPLETED; - atmel_qspi_write(QSPI_SR_CMD_COMPLETED, aq, QSPI_IER); - if (!wait_for_completion_timeout(&aq->cmd_completion, - msecs_to_jiffies(1000))) - err = -ETIMEDOUT; - atmel_qspi_write(QSPI_SR_CMD_COMPLETED, aq, QSPI_IDR); + err = aq->ops->transfer(mem, op, offset); pm_runtime_put: pm_runtime_mark_last_busy(&aq->pdev->dev); @@ -474,6 +981,159 @@ static const struct spi_controller_mem_ops atmel_qspi_mem_ops = { .get_name = atmel_qspi_get_name }; +static int atmel_qspi_set_pad_calibration(struct atmel_qspi *aq) +{ + unsigned long pclk_rate; + u32 status, val; + int i, ret; + u8 pclk_div = 0; + + pclk_rate = clk_get_rate(aq->pclk); + if (!pclk_rate) + return -EINVAL; + + for (i = 0; i < ATMEL_QSPI_PCAL_ARRAY_SIZE; i++) { + if (pclk_rate <= pcal[i].pclk_rate) { + pclk_div = pcal[i].pclk_div; + break; + } + } + + /* + * Use the biggest divider in case the peripheral clock exceeds + * 200MHZ. + */ + if (pclk_rate > pcal[ATMEL_QSPI_PCAL_ARRAY_SIZE - 1].pclk_rate) + pclk_div = pcal[ATMEL_QSPI_PCAL_ARRAY_SIZE - 1].pclk_div; + + /* Disable QSPI while configuring the pad calibration. */ + status = atmel_qspi_read(aq, QSPI_SR2); + if (status & QSPI_SR2_QSPIENS) { + ret = atmel_qspi_reg_sync(aq); + if (ret) + return ret; + atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); + } + + /* + * The analog circuitry is not shut down at the end of the calibration + * and the start-up time is only required for the first calibration + * sequence, thus increasing performance. Set the delay between the Pad + * calibration analog circuitry and the calibration request to 2us. + */ + atmel_qspi_write(QSPI_PCALCFG_AAON | + FIELD_PREP(QSPI_PCALCFG_CLKDIV, pclk_div) | + FIELD_PREP(QSPI_PCALCFG_CALCNT, + 2 * (pclk_rate / 1000000)), + aq, QSPI_PCALCFG); + + /* DLL On + start calibration. */ + atmel_qspi_write(QSPI_CR_DLLON | QSPI_CR_STPCAL, aq, QSPI_CR); + + /* Check synchronization status before updating configuration. */ + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + (val & QSPI_SR2_DLOCK) && + !(val & QSPI_SR2_CALBSY), 40, + ATMEL_QSPI_TIMEOUT); + + /* Refresh analogic blocks every 1 ms.*/ + atmel_qspi_write(FIELD_PREP(QSPI_REFRESH_DELAY_COUNTER, + aq->target_max_speed_hz / 1000), + aq, QSPI_REFRESH); + + return ret; +} + +static int atmel_qspi_set_gclk(struct atmel_qspi *aq) +{ + u32 status, val; + int ret; + + /* Disable DLL before setting GCLK */ + status = atmel_qspi_read(aq, QSPI_SR2); + if (status & QSPI_SR2_DLOCK) { + atmel_qspi_write(QSPI_CR_DLLOFF, aq, QSPI_CR); + + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_DLOCK), 40, + ATMEL_QSPI_TIMEOUT); + if (ret) + return ret; + } + + if (aq->target_max_speed_hz > QSPI_DLLCFG_THRESHOLD_FREQ) + atmel_qspi_write(QSPI_DLLCFG_RANGE, aq, QSPI_DLLCFG); + else + atmel_qspi_write(0, aq, QSPI_DLLCFG); + + ret = clk_set_rate(aq->gclk, aq->target_max_speed_hz); + if (ret) { + dev_err(&aq->pdev->dev, "Failed to set generic clock rate.\n"); + return ret; + } + + /* Enable the QSPI generic clock */ + ret = clk_prepare_enable(aq->gclk); + if (ret) + dev_err(&aq->pdev->dev, "Failed to enable generic clock.\n"); + + return ret; +} + +static int atmel_qspi_sama7g5_init(struct atmel_qspi *aq) +{ + u32 val; + int ret; + + ret = atmel_qspi_set_gclk(aq); + if (ret) + return ret; + + if (aq->caps->octal) { + ret = atmel_qspi_set_pad_calibration(aq); + if (ret) + return ret; + } else { + atmel_qspi_write(QSPI_CR_DLLON, aq, QSPI_CR); + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + (val & QSPI_SR2_DLOCK), 40, + ATMEL_QSPI_TIMEOUT); + } + + /* Set the QSPI controller by default in Serial Memory Mode */ + aq->mr |= QSPI_MR_DQSDLYEN; + ret = atmel_qspi_set_serial_memory_mode(aq); + if (ret < 0) + return ret; + + /* Enable the QSPI controller. */ + atmel_qspi_write(QSPI_CR_QSPIEN, aq, QSPI_CR); + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + val & QSPI_SR2_QSPIENS, 40, + ATMEL_QSPI_SYNC_TIMEOUT); + if (ret) + return ret; + + if (aq->caps->octal) { + ret = readl_poll_timeout(aq->regs + QSPI_SR, val, + val & QSPI_SR_RFRSHD, 40, + ATMEL_QSPI_TIMEOUT); + } + + atmel_qspi_write(QSPI_TOUT_TCNTM, aq, QSPI_TOUT); + return ret; +} + +static int atmel_qspi_sama7g5_setup(struct spi_device *spi) +{ + struct atmel_qspi *aq = spi_controller_get_devdata(spi->controller); + + /* The controller can communicate with a single peripheral device (target). */ + aq->target_max_speed_hz = spi->max_speed_hz; + + return atmel_qspi_sama7g5_init(aq); +} + static int atmel_qspi_setup(struct spi_device *spi) { struct spi_controller *ctrl = spi->controller; @@ -488,6 +1148,9 @@ static int atmel_qspi_setup(struct spi_device *spi) if (!spi->max_speed_hz) return -EINVAL; + if (aq->caps->has_gclk) + return atmel_qspi_sama7g5_setup(spi); + src_rate = clk_get_rate(aq->pclk); if (!src_rate) return -EINVAL; @@ -573,17 +1236,29 @@ static int atmel_qspi_set_cs_timing(struct spi_device *spi) return 0; } -static void atmel_qspi_init(struct atmel_qspi *aq) +static int atmel_qspi_init(struct atmel_qspi *aq) { + int ret; + + if (aq->caps->has_gclk) { + ret = atmel_qspi_reg_sync(aq); + if (ret) + return ret; + atmel_qspi_write(QSPI_CR_SWRST, aq, QSPI_CR); + return 0; + } + /* Reset the QSPI controller */ atmel_qspi_write(QSPI_CR_SWRST, aq, QSPI_CR); /* Set the QSPI controller by default in Serial Memory Mode */ - aq->mr |= QSPI_MR_SMM; - atmel_qspi_write(aq->mr, aq, QSPI_MR); + ret = atmel_qspi_set_serial_memory_mode(aq); + if (ret < 0) + return ret; /* Enable the QSPI controller */ atmel_qspi_write(QSPI_CR_QSPIEN, aq, QSPI_CR); + return 0; } static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id) @@ -599,12 +1274,65 @@ static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id) return IRQ_NONE; aq->pending |= pending; - if ((aq->pending & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) + if ((aq->pending & aq->irq_mask) == aq->irq_mask) complete(&aq->cmd_completion); return IRQ_HANDLED; } +static int atmel_qspi_dma_init(struct spi_controller *ctrl) +{ + struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); + int ret; + + aq->rx_chan = dma_request_chan(&aq->pdev->dev, "rx"); + if (IS_ERR(aq->rx_chan)) { + aq->rx_chan = NULL; + return dev_err_probe(&aq->pdev->dev, PTR_ERR(aq->rx_chan), + "RX DMA channel is not available\n"); + } + + aq->tx_chan = dma_request_chan(&aq->pdev->dev, "tx"); + if (IS_ERR(aq->tx_chan)) { + ret = dev_err_probe(&aq->pdev->dev, PTR_ERR(aq->tx_chan), + "TX DMA channel is not available\n"); + goto release_rx_chan; + } + + ctrl->dma_rx = aq->rx_chan; + ctrl->dma_tx = aq->tx_chan; + init_completion(&aq->dma_completion); + + dev_info(&aq->pdev->dev, "Using %s (tx) and %s (rx) for DMA transfers\n", + dma_chan_name(aq->tx_chan), dma_chan_name(aq->rx_chan)); + + return 0; + +release_rx_chan: + dma_release_channel(aq->rx_chan); + aq->rx_chan = NULL; + aq->tx_chan = NULL; + return ret; +} + +static void atmel_qspi_dma_release(struct atmel_qspi *aq) +{ + if (aq->rx_chan) + dma_release_channel(aq->rx_chan); + if (aq->tx_chan) + dma_release_channel(aq->tx_chan); +} + +static const struct atmel_qspi_ops atmel_qspi_ops = { + .set_cfg = atmel_qspi_set_cfg, + .transfer = atmel_qspi_transfer, +}; + +static const struct atmel_qspi_ops atmel_qspi_sama7g5_ops = { + .set_cfg = atmel_qspi_sama7g5_set_cfg, + .transfer = atmel_qspi_sama7g5_transfer, +}; + static int atmel_qspi_probe(struct platform_device *pdev) { struct spi_controller *ctrl; @@ -616,7 +1344,27 @@ static int atmel_qspi_probe(struct platform_device *pdev) if (!ctrl) return -ENOMEM; + aq = spi_controller_get_devdata(ctrl); + + aq->caps = of_device_get_match_data(&pdev->dev); + if (!aq->caps) { + dev_err(&pdev->dev, "Could not retrieve QSPI caps\n"); + return -EINVAL; + } + + init_completion(&aq->cmd_completion); + aq->pdev = pdev; + ctrl->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD; + if (aq->caps->octal) + ctrl->mode_bits |= SPI_RX_OCTAL | SPI_TX_OCTAL; + + if (aq->caps->has_gclk) + aq->ops = &atmel_qspi_sama7g5_ops; + else + aq->ops = &atmel_qspi_ops; + + ctrl->max_speed_hz = aq->caps->max_speed_hz; ctrl->setup = atmel_qspi_setup; ctrl->set_cs_timing = atmel_qspi_set_cs_timing; ctrl->bus_num = -1; @@ -625,11 +1373,6 @@ static int atmel_qspi_probe(struct platform_device *pdev) ctrl->dev.of_node = pdev->dev.of_node; platform_set_drvdata(pdev, ctrl); - aq = spi_controller_get_devdata(ctrl); - - init_completion(&aq->cmd_completion); - aq->pdev = pdev; - /* Map the registers */ aq->regs = devm_platform_ioremap_resource_byname(pdev, "qspi_base"); if (IS_ERR(aq->regs)) @@ -644,57 +1387,52 @@ static int atmel_qspi_probe(struct platform_device *pdev) "missing AHB memory\n"); aq->mmap_size = resource_size(res); + aq->mmap_phys_base = (dma_addr_t)res->start; /* Get the peripheral clock */ - aq->pclk = devm_clk_get(&pdev->dev, "pclk"); + aq->pclk = devm_clk_get_enabled(&pdev->dev, "pclk"); if (IS_ERR(aq->pclk)) - aq->pclk = devm_clk_get(&pdev->dev, NULL); + aq->pclk = devm_clk_get_enabled(&pdev->dev, NULL); if (IS_ERR(aq->pclk)) return dev_err_probe(&pdev->dev, PTR_ERR(aq->pclk), "missing peripheral clock\n"); - /* Enable the peripheral clock */ - err = clk_prepare_enable(aq->pclk); - if (err) - return dev_err_probe(&pdev->dev, err, - "failed to enable the peripheral clock\n"); - - aq->caps = of_device_get_match_data(&pdev->dev); - if (!aq->caps) { - dev_err(&pdev->dev, "Could not retrieve QSPI caps\n"); - err = -EINVAL; - goto disable_pclk; - } - if (aq->caps->has_qspick) { /* Get the QSPI system clock */ - aq->qspick = devm_clk_get(&pdev->dev, "qspick"); + aq->qspick = devm_clk_get_enabled(&pdev->dev, "qspick"); if (IS_ERR(aq->qspick)) { dev_err(&pdev->dev, "missing system clock\n"); err = PTR_ERR(aq->qspick); - goto disable_pclk; + return err; } - /* Enable the QSPI system clock */ - err = clk_prepare_enable(aq->qspick); - if (err) { - dev_err(&pdev->dev, - "failed to enable the QSPI system clock\n"); - goto disable_pclk; + } else if (aq->caps->has_gclk) { + /* Get the QSPI generic clock */ + aq->gclk = devm_clk_get(&pdev->dev, "gclk"); + if (IS_ERR(aq->gclk)) { + dev_err(&pdev->dev, "missing Generic clock\n"); + err = PTR_ERR(aq->gclk); + return err; } } + if (aq->caps->has_dma) { + err = atmel_qspi_dma_init(ctrl); + if (err == -EPROBE_DEFER) + return err; + } + /* Request the IRQ */ irq = platform_get_irq(pdev, 0); if (irq < 0) { err = irq; - goto disable_qspick; + goto dma_release; } err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, 0, dev_name(&pdev->dev), aq); if (err) - goto disable_qspick; + goto dma_release; pm_runtime_set_autosuspend_delay(&pdev->dev, 500); pm_runtime_use_autosuspend(&pdev->dev); @@ -702,7 +1440,9 @@ static int atmel_qspi_probe(struct platform_device *pdev) pm_runtime_enable(&pdev->dev); pm_runtime_get_noresume(&pdev->dev); - atmel_qspi_init(aq); + err = atmel_qspi_init(aq); + if (err) + goto dma_release; err = spi_register_controller(ctrl); if (err) { @@ -710,21 +1450,57 @@ static int atmel_qspi_probe(struct platform_device *pdev) pm_runtime_disable(&pdev->dev); pm_runtime_set_suspended(&pdev->dev); pm_runtime_dont_use_autosuspend(&pdev->dev); - goto disable_qspick; + goto dma_release; } pm_runtime_mark_last_busy(&pdev->dev); pm_runtime_put_autosuspend(&pdev->dev); return 0; -disable_qspick: - clk_disable_unprepare(aq->qspick); -disable_pclk: - clk_disable_unprepare(aq->pclk); +dma_release: + if (aq->caps->has_dma) + atmel_qspi_dma_release(aq); return err; } +static int atmel_qspi_sama7g5_suspend(struct atmel_qspi *aq) +{ + int ret; + u32 val; + + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_RBUSY) && + (val & QSPI_SR2_HIDLE), 40, + ATMEL_QSPI_SYNC_TIMEOUT); + if (ret) + return ret; + + atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_QSPIENS), 40, + ATMEL_QSPI_SYNC_TIMEOUT); + if (ret) + return ret; + + clk_disable_unprepare(aq->gclk); + + atmel_qspi_write(QSPI_CR_DLLOFF, aq, QSPI_CR); + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_DLOCK), 40, + ATMEL_QSPI_TIMEOUT); + if (ret) + return ret; + + ret = readl_poll_timeout(aq->regs + QSPI_SR2, val, + !(val & QSPI_SR2_CALBSY), 40, + ATMEL_QSPI_TIMEOUT); + if (ret) + return ret; + + return 0; +} + static void atmel_qspi_remove(struct platform_device *pdev) { struct spi_controller *ctrl = platform_get_drvdata(pdev); @@ -735,9 +1511,17 @@ static void atmel_qspi_remove(struct platform_device *pdev) ret = pm_runtime_get_sync(&pdev->dev); if (ret >= 0) { + if (aq->caps->has_dma) + atmel_qspi_dma_release(aq); + + if (aq->caps->has_gclk) { + ret = atmel_qspi_sama7g5_suspend(aq); + if (ret) + dev_warn(&pdev->dev, "Failed to de-init device on remove: %d\n", ret); + return; + } + atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); - clk_disable(aq->qspick); - clk_disable(aq->pclk); } else { /* * atmel_qspi_runtime_{suspend,resume} just disable and enable @@ -747,9 +1531,6 @@ static void atmel_qspi_remove(struct platform_device *pdev) dev_warn(&pdev->dev, "Failed to resume device on remove\n"); } - clk_unprepare(aq->qspick); - clk_unprepare(aq->pclk); - pm_runtime_disable(&pdev->dev); pm_runtime_dont_use_autosuspend(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); @@ -765,6 +1546,12 @@ static int __maybe_unused atmel_qspi_suspend(struct device *dev) if (ret < 0) return ret; + if (aq->caps->has_gclk) { + ret = atmel_qspi_sama7g5_suspend(aq); + clk_disable_unprepare(aq->pclk); + return ret; + } + atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); pm_runtime_mark_last_busy(dev); @@ -792,6 +1579,9 @@ static int __maybe_unused atmel_qspi_resume(struct device *dev) return ret; } + if (aq->caps->has_gclk) + return atmel_qspi_sama7g5_init(aq); + ret = pm_runtime_force_resume(dev); if (ret < 0) return ret; @@ -847,6 +1637,19 @@ static const struct atmel_qspi_caps atmel_sam9x60_qspi_caps = { .has_ricr = true, }; +static const struct atmel_qspi_caps atmel_sama7g5_ospi_caps = { + .max_speed_hz = SAMA7G5_QSPI0_MAX_SPEED_HZ, + .has_gclk = true, + .octal = true, + .has_dma = true, +}; + +static const struct atmel_qspi_caps atmel_sama7g5_qspi_caps = { + .max_speed_hz = SAMA7G5_QSPI1_SDR_MAX_SPEED_HZ, + .has_gclk = true, + .has_dma = true, +}; + static const struct of_device_id atmel_qspi_dt_ids[] = { { .compatible = "atmel,sama5d2-qspi", @@ -856,6 +1659,15 @@ static const struct of_device_id atmel_qspi_dt_ids[] = { .compatible = "microchip,sam9x60-qspi", .data = &atmel_sam9x60_qspi_caps, }, + { + .compatible = "microchip,sama7g5-ospi", + .data = &atmel_sama7g5_ospi_caps, + }, + { + .compatible = "microchip,sama7g5-qspi", + .data = &atmel_sama7g5_qspi_caps, + }, + { /* sentinel */ } }; |