diff options
Diffstat (limited to 'arch/arm/plat-omap/include')
| -rw-r--r-- | arch/arm/plat-omap/include/plat/mmc.h | 1 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/omap_hwmod.h | 6 | ||||
| -rw-r--r-- | arch/arm/plat-omap/include/plat/serial.h | 9 |
3 files changed, 7 insertions, 9 deletions
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h index 8b4e4f2da2f5..346af5b490be 100644 --- a/arch/arm/plat-omap/include/plat/mmc.h +++ b/arch/arm/plat-omap/include/plat/mmc.h @@ -126,6 +126,7 @@ struct omap_mmc_platform_data { /* we can put the features above into this variable */ #define HSMMC_HAS_PBIAS (1 << 0) #define HSMMC_HAS_UPDATED_RESET (1 << 1) +#define HSMMC_HAS_HSPE_SUPPORT (1 << 2) unsigned features; int switch_pin; /* gpio (card detect) */ diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h index b3349f7b1a2c..1db029438022 100644 --- a/arch/arm/plat-omap/include/plat/omap_hwmod.h +++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h @@ -443,6 +443,11 @@ struct omap_hwmod_omap4_prcm { * in order to complete the reset. Optional clocks will be disabled * again after the reset. * HWMOD_16BIT_REG: Module has 16bit registers + * HWMOD_EXT_OPT_MAIN_CLK: The only main functional clock source for + * this IP block comes from an off-chip source and is not always + * enabled. This prevents the hwmod code from being able to + * enable and reset the IP block early. XXX Eventually it should + * be possible to query the clock framework for this information. */ #define HWMOD_SWSUP_SIDLE (1 << 0) #define HWMOD_SWSUP_MSTANDBY (1 << 1) @@ -453,6 +458,7 @@ struct omap_hwmod_omap4_prcm { #define HWMOD_NO_IDLEST (1 << 6) #define HWMOD_CONTROL_OPT_CLKS_IN_RESET (1 << 7) #define HWMOD_16BIT_REG (1 << 8) +#define HWMOD_EXT_OPT_MAIN_CLK (1 << 9) /* * omap_hwmod._int_flags definitions diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h index 65fce44dce34..b780470d03ea 100644 --- a/arch/arm/plat-omap/include/plat/serial.h +++ b/arch/arm/plat-omap/include/plat/serial.h @@ -109,15 +109,6 @@ #define OMAP5UART4 OMAP4UART4 #define ZOOM_UART 95 /* Only on zoom2/3 */ -/* This is only used by 8250.c for omap1510 */ -#define is_omap_port(pt) ({int __ret = 0; \ - if ((pt)->port.mapbase == OMAP1_UART1_BASE || \ - (pt)->port.mapbase == OMAP1_UART2_BASE || \ - (pt)->port.mapbase == OMAP1_UART3_BASE) \ - __ret = 1; \ - __ret; \ - }) - #ifndef __ASSEMBLER__ struct omap_board_data; |