diff options
Diffstat (limited to 'Documentation/devicetree')
50 files changed, 1648 insertions, 663 deletions
diff --git a/Documentation/devicetree/bindings/display/bridge/ite,it6263.yaml b/Documentation/devicetree/bindings/display/bridge/ite,it6263.yaml new file mode 100644 index 000000000000..0a10e10d80ff --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ite,it6263.yaml @@ -0,0 +1,250 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/ite,it6263.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ITE IT6263 LVDS to HDMI converter + +maintainers: + - Liu Ying <victor.liu@nxp.com> + +description: | + The IT6263 is a high-performance single-chip De-SSC(De-Spread Spectrum) LVDS + to HDMI converter. Combined with LVDS receiver and HDMI 1.4a transmitter, + the IT6263 supports LVDS input and HDMI 1.4 output by conversion function. + The built-in LVDS receiver can support single-link and dual-link LVDS inputs, + and the built-in HDMI transmitter is fully compliant with HDMI 1.4a/3D, HDCP + 1.2 and backward compatible with DVI 1.0 specification. + + The IT6263 also encodes and transmits up to 8 channels of I2S digital audio, + with sampling rate up to 192KHz and sample size up to 24 bits. In addition, + an S/PDIF input port takes in compressed audio of up to 192KHz frame rate. + + The newly supported High-Bit Rate(HBR) audio by HDMI specifications v1.3 is + provided by the IT6263 in two interfaces: the four I2S input ports or the + S/PDIF input port. With both interfaces the highest possible HBR frame rate + is supported at up to 768KHz. + +allOf: + - $ref: /schemas/display/lvds-dual-ports.yaml# + +properties: + compatible: + const: ite,it6263 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + description: audio master clock + + clock-names: + const: mclk + + data-mapping: + enum: + - jeida-18 + - jeida-24 + - jeida-30 + - vesa-24 + - vesa-30 + + reset-gpios: + maxItems: 1 + + ivdd-supply: + description: 1.8V digital logic power + + ovdd-supply: + description: 3.3V I/O pin power + + txavcc18-supply: + description: 1.8V HDMI analog frontend power + + txavcc33-supply: + description: 3.3V HDMI analog frontend power + + pvcc1-supply: + description: 1.8V HDMI frontend core PLL power + + pvcc2-supply: + description: 1.8V HDMI frontend filter PLL power + + avcc-supply: + description: 3.3V LVDS frontend power + + anvdd-supply: + description: 1.8V LVDS frontend analog power + + apvdd-supply: + description: 1.8V LVDS frontend PLL power + + "#sound-dai-cells": + const: 0 + + ite,i2s-audio-fifo-sources: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + items: + enum: [0, 1, 2, 3] + description: + Each array element indicates the pin number of an I2S serial data input + line which is connected to an audio FIFO, from audio FIFO0 to FIFO3. + + ite,rl-channel-swap-audio-sources: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + uniqueItems: true + items: + enum: [0, 1, 2, 3] + description: + Each array element indicates an audio source whose right channel and left + channel are swapped by this converter. For I2S, the element is the pin + number of an I2S serial data input line. For S/PDIF, the element is always + 0. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: true + + port@1: + oneOf: + - required: [dual-lvds-odd-pixels] + - required: [dual-lvds-even-pixels] + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: video port for the HDMI output + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: sound input port + + required: + - port@0 + - port@2 + +required: + - compatible + - reg + - data-mapping + - ivdd-supply + - ovdd-supply + - txavcc18-supply + - txavcc33-supply + - pvcc1-supply + - pvcc2-supply + - avcc-supply + - anvdd-supply + - apvdd-supply + +unevaluatedProperties: false + +examples: + - | + /* single-link LVDS input */ + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi@4c { + compatible = "ite,it6263"; + reg = <0x4c>; + data-mapping = "jeida-24"; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + ivdd-supply = <®_buck5>; + ovdd-supply = <®_vext_3v3>; + txavcc18-supply = <®_buck5>; + txavcc33-supply = <®_vext_3v3>; + pvcc1-supply = <®_buck5>; + pvcc2-supply = <®_buck5>; + avcc-supply = <®_vext_3v3>; + anvdd-supply = <®_buck5>; + apvdd-supply = <®_buck5>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + it6263_lvds_link1: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; + + port@2 { + reg = <2>; + + it6263_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; + }; + + - | + /* dual-link LVDS input */ + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi@4c { + compatible = "ite,it6263"; + reg = <0x4c>; + data-mapping = "jeida-24"; + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + ivdd-supply = <®_buck5>; + ovdd-supply = <®_vext_3v3>; + txavcc18-supply = <®_buck5>; + txavcc33-supply = <®_vext_3v3>; + pvcc1-supply = <®_buck5>; + pvcc2-supply = <®_buck5>; + avcc-supply = <®_vext_3v3>; + anvdd-supply = <®_buck5>; + apvdd-supply = <®_buck5>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + it6263_lvds_link1_dual: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; + + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + it6263_lvds_link2_dual: endpoint { + remote-endpoint = <&ldb_lvds_ch1>; + }; + }; + + port@2 { + reg = <2>; + + it6263_out_dual: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml b/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml index 5a69547ad3d7..1509c4535e53 100644 --- a/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml +++ b/Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml @@ -81,9 +81,22 @@ properties: properties: port@0: - $ref: /schemas/graph.yaml#/properties/port + unevaluatedProperties: false + $ref: /schemas/graph.yaml#/$defs/port-base description: Parallel RGB input port + properties: + endpoint: + $ref: /schemas/graph.yaml#/$defs/endpoint-base + unevaluatedProperties: false + + properties: + bus-width: + description: + Endpoint bus width. + enum: [ 16, 18, 24 ] + default: 24 + port@1: $ref: /schemas/graph.yaml#/properties/port description: HDMI output port diff --git a/Documentation/devicetree/bindings/display/bridge/ti,tdp158.yaml b/Documentation/devicetree/bindings/display/bridge/ti,tdp158.yaml new file mode 100644 index 000000000000..1c522f72c4ba --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,tdp158.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/ti,tdp158.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI TDP158 HDMI to TMDS Redriver + +maintainers: + - Arnaud Vrac <avrac@freebox.fr> + - Pierre-Hugues Husson <phhusson@freebox.fr> + +properties: + compatible: + const: ti,tdp158 + +# The reg property is required if and only if the device is connected +# to an I2C bus. In pin strap mode, reg must not be specified. + reg: + description: I2C address of the device + +# Pin 36 = Operation Enable / Reset Pin +# OE = L: Power Down Mode +# OE = H: Normal Operation +# Internal weak pullup - device resets on H to L transitions + enable-gpios: + description: GPIO controlling bridge enable + + vcc-supply: + description: Power supply 3.3V + + vdd-supply: + description: Power supply 1.1V + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Bridge input + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Bridge output + + required: + - port@0 + - port@1 + +required: + - compatible + - vcc-supply + - vdd-supply + - ports + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml index 779d8c57f854..bb5d3b543800 100644 --- a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml @@ -60,6 +60,10 @@ properties: data-lines: $ref: /schemas/types.yaml#/definitions/uint32 enum: [ 16, 18, 24 ] + deprecated: true + + bus-width: + enum: [ 16, 18, 24 ] port@1: $ref: /schemas/graph.yaml#/properties/port diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt index 3c35338a2867..269b1ae2fca9 100644 --- a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt @@ -119,7 +119,6 @@ Optional properties: - interface-pix-fmt: How this display is connected to the display interface. Currently supported types: "rgb24", "rgb565", "bgr666" and "lvds666". -- edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel - port@[0-1]: Port nodes with endpoint definitions as defined in @@ -131,7 +130,6 @@ example: disp0 { compatible = "fsl,imx-parallel-display"; - edid = [edid-data]; interface-pix-fmt = "rgb24"; port@0 { diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 8e6e7d797943..03653a291b54 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,7 +62,6 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): - - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/panel/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/display/lvds-data-mapping.yaml b/Documentation/devicetree/bindings/display/lvds-data-mapping.yaml index d68982fe2e9b..ab842594feb9 100644 --- a/Documentation/devicetree/bindings/display/lvds-data-mapping.yaml +++ b/Documentation/devicetree/bindings/display/lvds-data-mapping.yaml @@ -26,12 +26,17 @@ description: | Device compatible with those specifications have been marketed under the FPD-Link and FlatLink brands. + This bindings also supports 30-bit data mapping compatible with JEIDA and + VESA. + properties: data-mapping: enum: - jeida-18 - jeida-24 + - jeida-30 - vesa-24 + - vesa-30 description: | The color signals mapping order. @@ -60,6 +65,19 @@ properties: DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__>< DATA3 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__>< + - "jeida-30" - 30-bit data mapping compatible with JEIDA and VESA. Data + are transferred as follows on 5 LVDS lanes. + + Slot 0 1 2 3 4 5 6 + ________________ _________________ + Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ + DATA0 ><__G4__><__R9__><__R8__><__R7__><__R6__><__R5__><__R4__>< + DATA1 ><__B5__><__B4__><__G9__><__G8__><__G7__><__G6__><__G5__>< + DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B9__><__B8__><__B7__><__B6__>< + DATA3 ><_CTL3_><__B3__><__B2__><__G3__><__G2__><__R3__><__R2__>< + DATA4 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__>< + - "vesa-24" - 24-bit data mapping compatible with the [VESA] specification. Data are transferred as follows on 4 LVDS lanes. @@ -72,6 +90,19 @@ properties: DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__>< + - "vesa-30" - 30-bit data mapping compatible with VESA. Data are + transferred as follows on 5 LVDS lanes. + + Slot 0 1 2 3 4 5 6 + ________________ _________________ + Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ + DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< + DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< + DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< + DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__>< + DATA4 ><_CTL3_><__B9__><__B8__><__G9__><__G8__><__R9__><__R8__>< + Control signals are mapped as follows. CTL0: HSync diff --git a/Documentation/devicetree/bindings/display/lvds-dual-ports.yaml b/Documentation/devicetree/bindings/display/lvds-dual-ports.yaml new file mode 100644 index 000000000000..785701fe1590 --- /dev/null +++ b/Documentation/devicetree/bindings/display/lvds-dual-ports.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/lvds-dual-ports.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Dual-link LVDS Display Common Properties + +maintainers: + - Liu Ying <victor.liu@nxp.com> + +description: | + Common properties for LVDS displays with dual LVDS links. Extend LVDS display + common properties defined in lvds.yaml. + + Dual-link LVDS displays receive odd pixels and even pixels separately from + the dual LVDS links. One link receives odd pixels and the other receives + even pixels. Some of those displays may also use only one LVDS link to + receive all pixels, being odd and even agnostic. + +allOf: + - $ref: lvds.yaml# + +properties: + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + '^port@[01]$': + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: | + port@0 represents the first LVDS input link. + port@1 represents the second LVDS input link. + + properties: + dual-lvds-odd-pixels: + type: boolean + description: LVDS input link for odd pixels + + dual-lvds-even-pixels: + type: boolean + description: LVDS input link for even pixels + + oneOf: + - required: [dual-lvds-odd-pixels] + - required: [dual-lvds-even-pixels] + - properties: + dual-lvds-odd-pixels: false + dual-lvds-even-pixels: false + + anyOf: + - required: + - port@0 + - required: + - port@1 + +required: + - ports + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml index cf24434854ff..47ddba5c41af 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml @@ -62,6 +62,27 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: AAL input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + AAL output to the next component's input, for example could be one + of many gamma, overdrive or other blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg @@ -89,5 +110,24 @@ examples: power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; clocks = <&mmsys CLK_MM_DISP_AAL>; mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x5000 0x1000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + aal0_in: endpoint { + remote-endpoint = <&ccorr0_out>; + }; + }; + + port@1 { + reg = <1>; + aal0_out: endpoint { + remote-endpoint = <&gamma0_in>; + }; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml index 9f8366763831..fca8e7bb0cbc 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml @@ -57,6 +57,27 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: CCORR input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + CCORR output to the input of the next desired component in the + display pipeline, usually only one of the available AAL blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml index 7df786bbad20..6160439ce4d7 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml @@ -65,6 +65,28 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: COLOR input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + COLOR output to the input of the next desired component in the + display pipeline, for example one of the available CCORR or AAL + blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml index 6fceb1f95d2a..abaf27916d13 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml @@ -56,6 +56,28 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: DITHER input, usually from a POSTMASK or GAMMA block. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + DITHER output to the input of the next desired component in the + display pipeline, for example one of the available DSC compressors, + DP_INTF, DSI, LVDS or others. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml index 497c0eb4ed0b..0f1e556dc8ef 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml @@ -81,13 +81,34 @@ properties: Output port node. This port should be connected to the input port of an attached HDMI, LVDS or DisplayPort encoder chip. + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: DPI input port + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: DPI output to an HDMI, LVDS or DisplayPort encoder input + + required: + - port@0 + - port@1 + required: - compatible - reg - interrupts - clocks - clock-names - - port + +oneOf: + - required: + - port + - required: + - ports additionalProperties: false @@ -96,7 +117,7 @@ examples: #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/mt8173-clk.h> - dpi0: dpi@1401d000 { + dpi: dpi@1401d000 { compatible = "mediatek,mt8173-dpi"; reg = <0x1401d000 0x1000>; interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsc.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsc.yaml index 2cbdd9ee449d..846de6c17d93 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsc.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsc.yaml @@ -49,6 +49,30 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Display Stream Compression input, usually from one of the DITHER + or MERGE blocks. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Display Stream Compression output to the input of the next desired + component in the display pipeline, for example to MERGE, DP_INTF, + DPI or DSI. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml index a7aa8fcb0dd1..27ffbccc2a08 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml @@ -77,6 +77,26 @@ properties: Output port node. This port should be connected to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input ports can have multiple endpoints, each of those connects + to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: DSI input port, usually from DITHER, DSC or MERGE + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + DSI output to an attached DSI panel, or a DSI-to-X encoder chip + + required: + - port@0 + - port@1 + required: - compatible - reg @@ -86,7 +106,12 @@ required: - clock-names - phys - phy-names - - port + +oneOf: + - required: + - port + - required: + - ports unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ethdr.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ethdr.yaml index 677882348ede..98db47894eeb 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ethdr.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ethdr.yaml @@ -110,6 +110,28 @@ properties: include/dt-bindings/gce/<chip>-gce.h, mapping to the register of display function block. + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: ETHDR input, usually from one of the MERGE blocks. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + ETHDR output to the input of the next desired component in the + display pipeline, for example one of the available MERGE blocks, + or others. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,gamma.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,gamma.yaml index 6823d3ce5049..48542dc7e784 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,gamma.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,gamma.yaml @@ -65,6 +65,25 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: GAMMA input, usually from one of the AAL blocks. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + GAMMA output to the input of the next desired component in the + display pipeline, for example one of the available DITHER or + POSTMASK blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml index dae839279950..0de9f64f3f84 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml @@ -77,6 +77,29 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + MERGE input port, usually from DITHER, DPI, DSC, DSI, MDP_RDMA, + ETHDR or even from a different MERGE block + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + MERGE output to a DSC, DPI, DP_INTF, DSI, ETHDR, Write DMA, or + a different MERGE block, or others. + + required: + - port@0 + - port@1 + resets: description: reset controller See Documentation/devicetree/bindings/reset/reset.txt for details. diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,od.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,od.yaml index 831c653caffd..71534febd49c 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,od.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,od.yaml @@ -38,6 +38,28 @@ properties: items: - description: OD Clock + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: OD input port, usually from an AAL block + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + OD output to the input of the next desired component in the + display pipeline, for example one of the available RDMA or + other blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl-2l.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl-2l.yaml index c7dd0ef02dcf..bacdfe7d08a6 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl-2l.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl-2l.yaml @@ -57,6 +57,28 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: OVL input port from MMSYS, VDOSYS or other OVLs + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + OVL output to the input of the next desired component in the + display pipeline, for example one of the available COLOR, RDMA + or WDMA blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl.yaml index d55611c7ce5e..9ea796a033b2 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ovl.yaml @@ -75,6 +75,28 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: OVL input port from MMSYS or one of multiple VDOSYS + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + OVL output to the input of the next desired component in the + display pipeline, for example one of the available COLOR, RDMA + or WDMA blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,postmask.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,postmask.yaml index 11fe32e50a59..fb6fe4742624 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,postmask.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,postmask.yaml @@ -52,6 +52,27 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: POSTMASK input port, usually from GAMMA + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + POSTMASK output to the input of the next desired component in the + display pipeline, for example one of the available DITHER blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,rdma.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,rdma.yaml index 4cadb245d028..878f676b581f 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,rdma.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,rdma.yaml @@ -87,6 +87,28 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array maxItems: 1 + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: RDMA input port, usually from MMSYS, OD or OVL + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + RDMA output to the input of the next desired component in the + display pipeline, for example one of the available COLOR, DPI, + DSI, MERGE or UFOE blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ufoe.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ufoe.yaml index 39e3e2d4a0db..61a5e22effbf 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ufoe.yaml +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ufoe.yaml @@ -43,6 +43,27 @@ properties: items: - description: UFOe Clock + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Input and output ports can have multiple endpoints, each of those + connects to either the primary, secondary, etc, display pipeline. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: UFOE input, usually from one of the RDMA blocks. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + UFOE output to the input of the next desired component in the + display pipeline, usually one of the available DSI blocks. + + required: + - port@0 + - port@1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml index 97993feda193..a212f335d5ff 100644 --- a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml +++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml @@ -17,6 +17,7 @@ properties: compatible: oneOf: - enum: + - qcom,sa8775p-dp - qcom,sc7180-dp - qcom,sc7280-dp - qcom,sc7280-edp diff --git a/Documentation/devicetree/bindings/display/msm/gmu.yaml b/Documentation/devicetree/bindings/display/msm/gmu.yaml index b1bd372996d5..ab884e236429 100644 --- a/Documentation/devicetree/bindings/display/msm/gmu.yaml +++ b/Documentation/devicetree/bindings/display/msm/gmu.yaml @@ -125,6 +125,7 @@ allOf: enum: - qcom,adreno-gmu-635.0 - qcom,adreno-gmu-660.1 + - qcom,adreno-gmu-663.0 then: properties: reg: diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sa8775p-mdss.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sa8775p-mdss.yaml new file mode 100644 index 000000000000..58f8a01f29c7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/qcom,sa8775p-mdss.yaml @@ -0,0 +1,241 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/qcom,sa8775p-mdss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SA87755P Display MDSS + +maintainers: + - Mahadevan <quic_mahap@quicinc.com> + +description: + SA8775P MSM Mobile Display Subsystem(MDSS), which encapsulates sub-blocks like + DPU display controller, DP interfaces and EDP etc. + +$ref: /schemas/display/msm/mdss-common.yaml# + +properties: + compatible: + const: qcom,sa8775p-mdss + + clocks: + items: + - description: Display AHB + - description: Display hf AXI + - description: Display core + + iommus: + maxItems: 1 + + interconnects: + maxItems: 3 + + interconnect-names: + maxItems: 3 + +patternProperties: + "^display-controller@[0-9a-f]+$": + type: object + additionalProperties: true + + properties: + compatible: + const: qcom,sa8775p-dpu + + "^displayport-controller@[0-9a-f]+$": + type: object + additionalProperties: true + + properties: + compatible: + items: + - const: qcom,sa8775p-dp + +required: + - compatible + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interconnect/qcom,icc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,sa8775p-gcc.h> + #include <dt-bindings/interconnect/qcom,sa8775p-rpmh.h> + #include <dt-bindings/power/qcom,rpmhpd.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + display-subsystem@ae00000 { + compatible = "qcom,sa8775p-mdss"; + reg = <0x0ae00000 0x1000>; + reg-names = "mdss"; + + interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>, + <&mmss_noc MASTER_MDP1 &mc_virt SLAVE_EBI1>, + <&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_DISPLAY_CFG>; + interconnect-names = "mdp0-mem", + "mdp1-mem", + "cpu-cfg"; + + + resets = <&dispcc_core_bcr>; + power-domains = <&dispcc_gdsc>; + + clocks = <&dispcc_ahb_clk>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc_mdp_clk>; + + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x1000 0x402>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + display-controller@ae01000 { + compatible = "qcom,sa8775p-dpu"; + reg = <0x0ae01000 0x8f000>, + <0x0aeb0000 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc_ahb_clk>, + <&dispcc_mdp_lut_clk>, + <&dispcc_mdp_clk>, + <&dispcc_mdp_vsync_clk>; + clock-names = "nrt_bus", + "iface", + "lut", + "core", + "vsync"; + + assigned-clocks = <&dispcc_mdp_vsync_clk>; + assigned-clock-rates = <19200000>; + + operating-points-v2 = <&mdss0_mdp_opp_table>; + power-domains = <&rpmhpd RPMHPD_MMCX>; + + interrupt-parent = <&mdss0>; + interrupts = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf0_out: endpoint { + remote-endpoint = <&mdss0_dp0_in>; + }; + }; + }; + + mdss0_mdp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-375000000 { + opp-hz = /bits/ 64 <375000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + + opp-575000000 { + opp-hz = /bits/ 64 <575000000>; + required-opps = <&rpmhpd_opp_turbo>; + }; + + opp-650000000 { + opp-hz = /bits/ 64 <650000000>; + required-opps = <&rpmhpd_opp_turbo_l1>; + }; + }; + }; + + displayport-controller@af54000 { + compatible = "qcom,sa8775p-dp"; + + pinctrl-0 = <&dp_hot_plug_det>; + pinctrl-names = "default"; + + reg = <0xaf54000 0x104>, + <0xaf54200 0x0c0>, + <0xaf55000 0x770>, + <0xaf56000 0x09c>; + + interrupt-parent = <&mdss0>; + interrupts = <12>; + + clocks = <&dispcc_mdss_ahb_clk>, + <&dispcc_dptx0_aux_clk>, + <&dispcc_dptx0_link_clk>, + <&dispcc_dptx0_link_intf_clk>, + <&dispcc_dptx0_pixel0_clk>; + clock-names = "core_iface", + "core_aux", + "ctrl_link", + "ctrl_link_iface", + "stream_pixel"; + + assigned-clocks = <&dispcc_mdss_dptx0_link_clk_src>, + <&dispcc_mdss_dptx0_pixel0_clk_src>; + assigned-clock-parents = <&mdss0_edp_phy 0>, <&mdss0_edp_phy 1>; + + phys = <&mdss0_edp_phy>; + phy-names = "dp"; + + operating-points-v2 = <&dp_opp_table>; + power-domains = <&rpmhpd SA8775P_MMCX>; + + #sound-dai-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdss0_dp0_in: endpoint { + remote-endpoint = <&dpu_intf0_out>; + }; + }; + + port@1 { + reg = <1>; + mdss0_dp_out: endpoint { }; + }; + }; + + dp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sc7280-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sc7280-dpu.yaml index b0fbe86219d1..6902795b4e2c 100644 --- a/Documentation/devicetree/bindings/display/msm/qcom,sc7280-dpu.yaml +++ b/Documentation/devicetree/bindings/display/msm/qcom,sc7280-dpu.yaml @@ -7,13 +7,21 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Display DPU on SC7280 maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Neil Armstrong <neil.armstrong@linaro.org> + - Dmitry Baryshkov <dmitry.baryshkov@linaro.org> - Krishna Manikandan <quic_mkrishn@quicinc.com> $ref: /schemas/display/msm/dpu-common.yaml# properties: compatible: - const: qcom,sc7280-dpu + enum: + - qcom,sc7280-dpu + - qcom,sc8280xp-dpu + - qcom,sm8350-dpu + - qcom,sm8450-dpu + - qcom,sm8550-dpu reg: items: diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sc8280xp-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sc8280xp-dpu.yaml deleted file mode 100644 index d19e3bec4600..000000000000 --- a/Documentation/devicetree/bindings/display/msm/qcom,sc8280xp-dpu.yaml +++ /dev/null @@ -1,122 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/msm/qcom,sc8280xp-dpu.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Qualcomm SC8280XP Display Processing Unit - -maintainers: - - Bjorn Andersson <andersson@kernel.org> - -description: - Device tree bindings for SC8280XP Display Processing Unit. - -$ref: /schemas/display/msm/dpu-common.yaml# - -properties: - compatible: - const: qcom,sc8280xp-dpu - - reg: - items: - - description: Address offset and size for mdp register set - - description: Address offset and size for vbif register set - - reg-names: - items: - - const: mdp - - const: vbif - - clocks: - items: - - description: Display hf axi clock - - description: Display sf axi clock - - description: Display ahb clock - - description: Display lut clock - - description: Display core clock - - description: Display vsync clock - - clock-names: - items: - - const: bus - - const: nrt_bus - - const: iface - - const: lut - - const: core - - const: vsync - -unevaluatedProperties: false - -examples: - - | - #include <dt-bindings/clock/qcom,dispcc-sc8280xp.h> - #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/interconnect/qcom,sc8280xp.h> - #include <dt-bindings/power/qcom-rpmpd.h> - - display-controller@ae01000 { - compatible = "qcom,sc8280xp-dpu"; - reg = <0x0ae01000 0x8f000>, - <0x0aeb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&gcc GCC_DISP_HF_AXI_CLK>, - <&gcc GCC_DISP_SF_AXI_CLK>, - <&dispcc0 DISP_CC_MDSS_AHB_CLK>, - <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>, - <&dispcc0 DISP_CC_MDSS_MDP_CLK>, - <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "bus", - "nrt_bus", - "iface", - "lut", - "core", - "vsync"; - - assigned-clocks = <&dispcc0 DISP_CC_MDSS_MDP_CLK>, - <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <460000000>, - <19200000>; - - operating-points-v2 = <&mdp_opp_table>; - power-domains = <&rpmhpd SC8280XP_MMCX>; - - interrupt-parent = <&mdss0>; - interrupts = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - endpoint { - remote-endpoint = <&mdss0_dp0_in>; - }; - }; - - port@4 { - reg = <4>; - endpoint { - remote-endpoint = <&mdss0_dp1_in>; - }; - }; - - port@5 { - reg = <5>; - endpoint { - remote-endpoint = <&mdss0_dp3_in>; - }; - }; - - port@6 { - reg = <6>; - endpoint { - remote-endpoint = <&mdss0_dp2_in>; - }; - }; - }; - }; -... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8150-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8150-dpu.yaml index 13146b3f053c..a88d22f30a60 100644 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8150-dpu.yaml +++ b/Documentation/devicetree/bindings/display/msm/qcom,sm8150-dpu.yaml @@ -13,7 +13,9 @@ $ref: /schemas/display/msm/dpu-common.yaml# properties: compatible: - const: qcom,sm8150-dpu + enum: + - qcom,sm8150-dpu + - qcom,sm8250-dpu reg: items: diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8250-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8250-dpu.yaml deleted file mode 100644 index ffa5047e901f..000000000000 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8250-dpu.yaml +++ /dev/null @@ -1,99 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/msm/qcom,sm8250-dpu.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Qualcomm SM8250 Display DPU - -maintainers: - - Dmitry Baryshkov <dmitry.baryshkov@linaro.org> - -$ref: /schemas/display/msm/dpu-common.yaml# - -properties: - compatible: - const: qcom,sm8250-dpu - - reg: - items: - - description: Address offset and size for mdp register set - - description: Address offset and size for vbif register set - - reg-names: - items: - - const: mdp - - const: vbif - - clocks: - items: - - description: Display ahb clock - - description: Display hf axi clock - - description: Display core clock - - description: Display vsync clock - - clock-names: - items: - - const: iface - - const: bus - - const: core - - const: vsync - -required: - - compatible - - reg - - reg-names - - clocks - - clock-names - -unevaluatedProperties: false - -examples: - - | - #include <dt-bindings/clock/qcom,dispcc-sm8250.h> - #include <dt-bindings/clock/qcom,gcc-sm8250.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/interconnect/qcom,sm8250.h> - #include <dt-bindings/power/qcom,rpmhpd.h> - - display-controller@ae01000 { - compatible = "qcom,sm8250-dpu"; - reg = <0x0ae01000 0x8f000>, - <0x0aeb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, - <&gcc GCC_DISP_HF_AXI_CLK>, - <&dispcc DISP_CC_MDSS_MDP_CLK>, - <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "iface", "bus", "core", "vsync"; - - assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <19200000>; - - operating-points-v2 = <&mdp_opp_table>; - power-domains = <&rpmhpd RPMHPD_MMCX>; - - interrupt-parent = <&mdss>; - interrupts = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - endpoint { - remote-endpoint = <&dsi0_in>; - }; - }; - - port@1 { - reg = <1>; - endpoint { - remote-endpoint = <&dsi1_in>; - }; - }; - }; - }; -... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8350-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8350-dpu.yaml deleted file mode 100644 index 96ef2d9c3512..000000000000 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8350-dpu.yaml +++ /dev/null @@ -1,120 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/msm/qcom,sm8350-dpu.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Qualcomm SM8350 Display DPU - -maintainers: - - Robert Foss <robert.foss@linaro.org> - -$ref: /schemas/display/msm/dpu-common.yaml# - -properties: - compatible: - const: qcom,sm8350-dpu - - reg: - items: - - description: Address offset and size for mdp register set - - description: Address offset and size for vbif register set - - reg-names: - items: - - const: mdp - - const: vbif - - clocks: - items: - - description: Display hf axi clock - - description: Display sf axi clock - - description: Display ahb clock - - description: Display lut clock - - description: Display core clock - - description: Display vsync clock - - clock-names: - items: - - const: bus - - const: nrt_bus - - const: iface - - const: lut - - const: core - - const: vsync - -unevaluatedProperties: false - -examples: - - | - #include <dt-bindings/clock/qcom,dispcc-sm8350.h> - #include <dt-bindings/clock/qcom,gcc-sm8350.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/interconnect/qcom,sm8350.h> - #include <dt-bindings/power/qcom,rpmhpd.h> - - display-controller@ae01000 { - compatible = "qcom,sm8350-dpu"; - reg = <0x0ae01000 0x8f000>, - <0x0aeb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&gcc GCC_DISP_HF_AXI_CLK>, - <&gcc GCC_DISP_SF_AXI_CLK>, - <&dispcc DISP_CC_MDSS_AHB_CLK>, - <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, - <&dispcc DISP_CC_MDSS_MDP_CLK>, - <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "bus", - "nrt_bus", - "iface", - "lut", - "core", - "vsync"; - - assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <19200000>; - - operating-points-v2 = <&mdp_opp_table>; - power-domains = <&rpmhpd RPMHPD_MMCX>; - - interrupt-parent = <&mdss>; - interrupts = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dpu_intf1_out: endpoint { - remote-endpoint = <&dsi0_in>; - }; - }; - }; - - mdp_opp_table: opp-table { - compatible = "operating-points-v2"; - - opp-200000000 { - opp-hz = /bits/ 64 <200000000>; - required-opps = <&rpmhpd_opp_low_svs>; - }; - - opp-300000000 { - opp-hz = /bits/ 64 <300000000>; - required-opps = <&rpmhpd_opp_svs>; - }; - - opp-345000000 { - opp-hz = /bits/ 64 <345000000>; - required-opps = <&rpmhpd_opp_svs_l1>; - }; - - opp-460000000 { - opp-hz = /bits/ 64 <460000000>; - required-opps = <&rpmhpd_opp_nom>; - }; - }; - }; -... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8450-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8450-dpu.yaml deleted file mode 100644 index 2a5d3daed0e1..000000000000 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8450-dpu.yaml +++ /dev/null @@ -1,139 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/msm/qcom,sm8450-dpu.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Qualcomm SM8450 Display DPU - -maintainers: - - Dmitry Baryshkov <dmitry.baryshkov@linaro.org> - -$ref: /schemas/display/msm/dpu-common.yaml# - -properties: - compatible: - const: qcom,sm8450-dpu - - reg: - items: - - description: Address offset and size for mdp register set - - description: Address offset and size for vbif register set - - reg-names: - items: - - const: mdp - - const: vbif - - clocks: - items: - - description: Display hf axi - - description: Display sf axi - - description: Display ahb - - description: Display lut - - description: Display core - - description: Display vsync - - clock-names: - items: - - const: bus - - const: nrt_bus - - const: iface - - const: lut - - const: core - - const: vsync - -required: - - compatible - - reg - - reg-names - - clocks - - clock-names - -unevaluatedProperties: false - -examples: - - | - #include <dt-bindings/clock/qcom,sm8450-dispcc.h> - #include <dt-bindings/clock/qcom,gcc-sm8450.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/interconnect/qcom,sm8450.h> - #include <dt-bindings/power/qcom,rpmhpd.h> - - display-controller@ae01000 { - compatible = "qcom,sm8450-dpu"; - reg = <0x0ae01000 0x8f000>, - <0x0aeb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&gcc GCC_DISP_HF_AXI_CLK>, - <&gcc GCC_DISP_SF_AXI_CLK>, - <&dispcc DISP_CC_MDSS_AHB_CLK>, - <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, - <&dispcc DISP_CC_MDSS_MDP_CLK>, - <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "bus", - "nrt_bus", - "iface", - "lut", - "core", - "vsync"; - - assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <19200000>; - - operating-points-v2 = <&mdp_opp_table>; - power-domains = <&rpmhpd RPMHPD_MMCX>; - - interrupt-parent = <&mdss>; - interrupts = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dpu_intf1_out: endpoint { - remote-endpoint = <&dsi0_in>; - }; - }; - - port@1 { - reg = <1>; - dpu_intf2_out: endpoint { - remote-endpoint = <&dsi1_in>; - }; - }; - }; - - mdp_opp_table: opp-table { - compatible = "operating-points-v2"; - - opp-172000000{ - opp-hz = /bits/ 64 <172000000>; - required-opps = <&rpmhpd_opp_low_svs_d1>; - }; - - opp-200000000 { - opp-hz = /bits/ 64 <200000000>; - required-opps = <&rpmhpd_opp_low_svs>; - }; - - opp-325000000 { - opp-hz = /bits/ 64 <325000000>; - required-opps = <&rpmhpd_opp_svs>; - }; - - opp-375000000 { - opp-hz = /bits/ 64 <375000000>; - required-opps = <&rpmhpd_opp_svs_l1>; - }; - - opp-500000000 { - opp-hz = /bits/ 64 <500000000>; - required-opps = <&rpmhpd_opp_nom>; - }; - }; - }; -... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8550-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8550-dpu.yaml deleted file mode 100644 index 16a541fca66f..000000000000 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8550-dpu.yaml +++ /dev/null @@ -1,133 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/display/msm/qcom,sm8550-dpu.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Qualcomm SM8550 Display DPU - -maintainers: - - Neil Armstrong <neil.armstrong@linaro.org> - -$ref: /schemas/display/msm/dpu-common.yaml# - -properties: - compatible: - const: qcom,sm8550-dpu - - reg: - items: - - description: Address offset and size for mdp register set - - description: Address offset and size for vbif register set - - reg-names: - items: - - const: mdp - - const: vbif - - clocks: - items: - - description: Display AHB - - description: Display hf axi - - description: Display MDSS ahb - - description: Display lut - - description: Display core - - description: Display vsync - - clock-names: - items: - - const: bus - - const: nrt_bus - - const: iface - - const: lut - - const: core - - const: vsync - -required: - - compatible - - reg - - reg-names - - clocks - - clock-names - -unevaluatedProperties: false - -examples: - - | - #include <dt-bindings/clock/qcom,sm8550-dispcc.h> - #include <dt-bindings/clock/qcom,sm8550-gcc.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/power/qcom,rpmhpd.h> - - display-controller@ae01000 { - compatible = "qcom,sm8550-dpu"; - reg = <0x0ae01000 0x8f000>, - <0x0aeb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&gcc GCC_DISP_AHB_CLK>, - <&gcc GCC_DISP_HF_AXI_CLK>, - <&dispcc DISP_CC_MDSS_AHB_CLK>, - <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, - <&dispcc DISP_CC_MDSS_MDP_CLK>, - <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "bus", - "nrt_bus", - "iface", - "lut", - "core", - "vsync"; - - assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <19200000>; - - operating-points-v2 = <&mdp_opp_table>; - power-domains = <&rpmhpd RPMHPD_MMCX>; - - interrupt-parent = <&mdss>; - interrupts = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dpu_intf1_out: endpoint { - remote-endpoint = <&dsi0_in>; - }; - }; - - port@1 { - reg = <1>; - dpu_intf2_out: endpoint { - remote-endpoint = <&dsi1_in>; - }; - }; - }; - - mdp_opp_table: opp-table { - compatible = "operating-points-v2"; - - opp-200000000 { - opp-hz = /bits/ 64 <200000000>; - required-opps = <&rpmhpd_opp_low_svs>; - }; - - opp-325000000 { - opp-hz = /bits/ 64 <325000000>; - required-opps = <&rpmhpd_opp_svs>; - }; - - opp-375000000 { - opp-hz = /bits/ 64 <375000000>; - required-opps = <&rpmhpd_opp_svs_l1>; - }; - - opp-514000000 { - opp-hz = /bits/ 64 <514000000>; - required-opps = <&rpmhpd_opp_nom>; - }; - }; - }; -... diff --git a/Documentation/devicetree/bindings/display/msm/qcom,sm8650-dpu.yaml b/Documentation/devicetree/bindings/display/msm/qcom,sm8650-dpu.yaml index c4087cc5abbd..01cf79bd754b 100644 --- a/Documentation/devicetree/bindings/display/msm/qcom,sm8650-dpu.yaml +++ b/Documentation/devicetree/bindings/display/msm/qcom,sm8650-dpu.yaml @@ -14,6 +14,7 @@ $ref: /schemas/display/msm/dpu-common.yaml# properties: compatible: enum: + - qcom,sa8775p-dpu - qcom,sm8650-dpu - qcom,x1e80100-dpu diff --git a/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.yaml b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.yaml index 2e8dbdb5a3d5..05ca3b2385f8 100644 --- a/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.yaml +++ b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.yaml @@ -20,6 +20,7 @@ description: | dual-lvds-odd-pixels or dual-lvds-even-pixels). allOf: + - $ref: /schemas/display/lvds-dual-ports.yaml# - $ref: panel-common.yaml# properties: @@ -44,22 +45,10 @@ properties: properties: port@0: - $ref: /schemas/graph.yaml#/$defs/port-base - unevaluatedProperties: false - description: The sink for odd pixels. - properties: - dual-lvds-odd-pixels: true - required: - dual-lvds-odd-pixels port@1: - $ref: /schemas/graph.yaml#/$defs/port-base - unevaluatedProperties: false - description: The sink for even pixels. - properties: - dual-lvds-even-pixels: true - required: - dual-lvds-even-pixels @@ -75,7 +64,6 @@ required: - height-mm - data-mapping - panel-timing - - ports examples: - |+ diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml index 0a57a31f4f3d..087415753d60 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-common.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml @@ -51,6 +51,14 @@ properties: $ref: /schemas/types.yaml#/definitions/uint32 enum: [0, 90, 180, 270] + flip-horizontal: + description: boolean to flip image horizontally + type: boolean + + flip-vertical: + description: boolean to flip image vertically + type: boolean + # Display Timings panel-timing: description: diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml b/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml index 155d8ffa8f6e..5af2d6930075 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.yaml @@ -50,6 +50,8 @@ properties: - hannstar,hsd101pww2 # Hydis Technologies 7" WXGA (800x1280) TFT LCD LVDS panel - hydis,hv070wx2-1e0 + # Jenson Display BL-JT60050-01A 7" WSVGA (1024x600) color TFT LCD LVDS panel + - jenson,bl-jt60050-01a - tbs,a711-panel - const: panel-lvds diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple-lvds-dual-ports.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple-lvds-dual-ports.yaml index 10ed4b57232b..e80fc7006984 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple-lvds-dual-ports.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple-lvds-dual-ports.yaml @@ -22,6 +22,7 @@ description: | If the panel is more advanced a dedicated binding file is required. allOf: + - $ref: /schemas/display/lvds-dual-ports.yaml# - $ref: panel-common.yaml# properties: @@ -55,28 +56,10 @@ properties: properties: port@0: - $ref: /schemas/graph.yaml#/$defs/port-base - unevaluatedProperties: false - description: The first sink port. - - properties: - dual-lvds-odd-pixels: - type: boolean - description: The first sink port for odd pixels. - required: - dual-lvds-odd-pixels port@1: - $ref: /schemas/graph.yaml#/$defs/port-base - unevaluatedProperties: false - description: The second sink port. - - properties: - dual-lvds-even-pixels: - type: boolean - description: The second sink port for even pixels. - required: - dual-lvds-even-pixels @@ -88,7 +71,6 @@ unevaluatedProperties: false required: - compatible - - ports - power-supply examples: diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index b89e39790579..18b63f356bb4 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -200,6 +200,8 @@ properties: - logictechno,lttd800480070-l2rt # Logic Technologies LTTD800480070-L6WH-RT 7” 800x480 TFT Resistive Touch Module - logictechno,lttd800480070-l6wh-rt + # Microchip AC69T88A 5" 800X480 LVDS interface TFT LCD Panel + - microchip,ac69t88a # Mitsubishi "AA070MC01 7.0" WVGA TFT LCD panel - mitsubishi,aa070mc01-ca1 # Mitsubishi AA084XE01 8.4" XGA TFT LCD panel diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ams581vf01.yaml b/Documentation/devicetree/bindings/display/panel/samsung,ams581vf01.yaml new file mode 100644 index 000000000000..70dff9c0ef2b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ams581vf01.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,ams581vf01.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung AMS581VF01 SOFEF01-based 5.81" 1080x2340 MIPI-DSI Panel + +maintainers: + - Danila Tikhonov <danila@jiaxyga.com> + +description: + The Samsung AMS581VF01 is a 5.81 inch 1080x2340 MIPI-DSI CMD mode OLED panel. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,ams581vf01 + + reg: + maxItems: 1 + + vdd3p3-supply: + description: 3.3V source voltage rail + + vddio-supply: + description: I/O source voltage rail + + vsn-supply: + description: Negative source voltage rail + + vsp-supply: + description: Positive source voltage rail + + reset-gpios: true + port: true + +required: + - compatible + - reg + - vdd3p3-supply + - vddio-supply + - vsn-supply + - vsp-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,ams581vf01"; + reg = <0>; + + vdd3p3-supply = <&vreg_l7c_3p0>; + vddio-supply = <&vreg_l13a_1p8>; + vsn-supply = <&vreg_ibb>; + vsp-supply = <&vreg_lab>; + + reset-gpios = <&pm6150l_gpios 9 GPIO_ACTIVE_LOW>; + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ams639rq08.yaml b/Documentation/devicetree/bindings/display/panel/samsung,ams639rq08.yaml new file mode 100644 index 000000000000..f5b6ecb96f99 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ams639rq08.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,ams639rq08.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung AMS639RQ08 EA8076-based 6.39" 1080x2340 MIPI-DSI Panel + +maintainers: + - Danila Tikhonov <danila@jiaxyga.com> + - Jens Reidel <adrian@travitia.xyz> + +description: + The Samsung AMS639RQ08 is a 6.39 inch 1080x2340 MIPI-DSI CMD mode AMOLED panel. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,ams639rq08 + + reg: + maxItems: 1 + + vdd3p3-supply: + description: 3.3V source voltage rail + + vddio-supply: + description: I/O source voltage rail + + vsn-supply: + description: Negative source voltage rail + + vsp-supply: + description: Positive source voltage rail + + reset-gpios: true + port: true + +required: + - compatible + - reg + - vdd3p3-supply + - vddio-supply + - vsn-supply + - vsp-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,ams639rq08"; + reg = <0>; + + vdd3p3-supply = <&vreg_l18a_2p8>; + vddio-supply = <&vreg_l13a_1p8>; + vsn-supply = <&vreg_ibb>; + vsp-supply = <&vreg_lab>; + + reset-gpios = <&pm6150l_gpios 9 GPIO_ACTIVE_LOW>; + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha8.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha8.yaml new file mode 100644 index 000000000000..05a78429aaea --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha8.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6e3ha8.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung s6e3ha8 AMOLED DSI panel + +description: The s6e3ha8 is a 1440x2960 DPI display panel from Samsung Mobile + Displays (SMD). + +maintainers: + - Dzmitry Sankouski <dsankouski@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6e3ha8 + + reg: + maxItems: 1 + + reset-gpios: true + + port: true + + vdd3-supply: + description: VDD regulator + + vci-supply: + description: VCI regulator + + vddr-supply: + description: VDDR regulator + +required: + - compatible + - reset-gpios + - vdd3-supply + - vci-supply + - vddr-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6e3ha8"; + reg = <0>; + vci-supply = <&s2dos05_ldo4>; + vddr-supply = <&s2dos05_buck1>; + vdd3-supply = <&s2dos05_ldo1>; + te-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>; + pinctrl-1 = <&sde_dsi_suspend &sde_te_active_sleep>; + pinctrl-names = "default", "sleep"; + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e88a0-ams427ap24.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6e88a0-ams427ap24.yaml new file mode 100644 index 000000000000..db284ba5be20 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e88a0-ams427ap24.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6e88a0-ams427ap24.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung AMS427AP24 panel with S6E88A0 controller + +maintainers: + - Jakob Hauser <jahau@rocketmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6e88a0-ams427ap24 + + reg: + maxItems: 1 + + port: true + reset-gpios: true + flip-horizontal: true + + vdd3-supply: + description: core voltage supply + + vci-supply: + description: voltage supply for analog circuits + +required: + - compatible + - reg + - port + - reset-gpios + - vdd3-supply + - vci-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6e88a0-ams427ap24"; + reg = <0>; + + vdd3-supply = <&pm8916_l17>; + vci-supply = <&pm8916_l6>; + reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>; + flip-horizontal; + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.yaml index 4601fa460680..19c8cc83db97 100644 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.yaml +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e8aa0.yaml @@ -21,6 +21,8 @@ properties: reset-gpios: true display-timings: true + flip-horizontal: true + flip-vertical: true vdd3-supply: description: core voltage supply @@ -46,14 +48,6 @@ properties: panel-height-mm: description: physical panel height [mm] - flip-horizontal: - description: boolean to flip image horizontally - type: boolean - - flip-vertical: - description: boolean to flip image vertically - type: boolean - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml new file mode 100644 index 000000000000..d8e761865f27 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip DW HDMI QP TX Encoder + +maintainers: + - Cristian Ciocaltea <cristian.ciocaltea@collabora.com> + +description: | + Rockchip RK3588 SoC integrates the Synopsys DesignWare HDMI QP TX controller + IP and a HDMI/eDP TX Combo PHY based on a Samsung IP block, providing the + following features, among others: + + * Fixed Rate Link (FRL) + * Display Stream Compression (DSC) + * 4K@120Hz and 8K@60Hz video modes + * Variable Refresh Rate (VRR) including Quick Media Switching (QMS) + * Fast Vactive (FVA) + * SCDC I2C DDC access + * Multi-stream audio + * Enhanced Audio Return Channel (EARC) + +allOf: + - $ref: /schemas/sound/dai-common.yaml# + +properties: + compatible: + enum: + - rockchip,rk3588-dw-hdmi-qp + + reg: + maxItems: 1 + + clocks: + items: + - description: Peripheral/APB bus clock + - description: EARC RX biphase clock + - description: Reference clock + - description: Audio interface clock + - description: TMDS/FRL link clock + - description: Video datapath clock + + clock-names: + items: + - const: pclk + - const: earc + - const: ref + - const: aud + - const: hdp + - const: hclk_vo1 + + interrupts: + items: + - description: AVP Unit interrupt + - description: CEC interrupt + - description: eARC RX interrupt + - description: Main Unit interrupt + - description: HPD interrupt + + interrupt-names: + items: + - const: avp + - const: cec + - const: earc + - const: main + - const: hpd + + phys: + maxItems: 1 + description: The HDMI/eDP PHY + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Video port for RGB/YUV input. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Video port for HDMI/eDP output. + + required: + - port@0 + - port@1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: ref + - const: hdp + + "#sound-dai-cells": + const: 0 + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some HDMI QP related data is accessed through SYS GRF regs. + + rockchip,vo-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Additional HDMI QP related data is accessed through VO GRF regs. + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - interrupt-names + - phys + - ports + - resets + - reset-names + - rockchip,grf + - rockchip,vo-grf + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/rockchip,rk3588-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/rk3588-power.h> + #include <dt-bindings/reset/rockchip,rk3588-cru.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + hdmi@fde80000 { + compatible = "rockchip,rk3588-dw-hdmi-qp"; + reg = <0x0 0xfde80000 0x0 0x20000>; + clocks = <&cru PCLK_HDMITX0>, + <&cru CLK_HDMITX0_EARC>, + <&cru CLK_HDMITX0_REF>, + <&cru MCLK_I2S5_8CH_TX>, + <&cru CLK_HDMIHDP0>, + <&cru HCLK_VO1>; + clock-names = "pclk", "earc", "ref", "aud", "hdp", "hclk_vo1"; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "avp", "cec", "earc", "main", "hpd"; + phys = <&hdptxphy_hdmi0>; + power-domains = <&power RK3588_PD_VO1>; + resets = <&cru SRST_HDMITX0_REF>, <&cru SRST_HDMIHDP0>; + reset-names = "ref", "hdp"; + rockchip,grf = <&sys_grf>; + rockchip,vo-grf = <&vo1_grf>; + #sound-dai-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in_vp0: endpoint { + remote-endpoint = <&vp0_out_hdmi0>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out_con0: endpoint { + remote-endpoint = <&hdmi_con0_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/samsung/samsung,exynos7-decon.yaml b/Documentation/devicetree/bindings/display/samsung/samsung,exynos7-decon.yaml index 992c23ca7a4e..53916e4c95d8 100644 --- a/Documentation/devicetree/bindings/display/samsung/samsung,exynos7-decon.yaml +++ b/Documentation/devicetree/bindings/display/samsung/samsung,exynos7-decon.yaml @@ -19,7 +19,9 @@ description: | properties: compatible: - const: samsung,exynos7-decon + enum: + - samsung,exynos7-decon + - samsung,exynos7870-decon clocks: maxItems: 4 diff --git a/Documentation/devicetree/bindings/display/sharp,ls010b7dh04.yaml b/Documentation/devicetree/bindings/display/sharp,ls010b7dh04.yaml new file mode 100644 index 000000000000..8097f091c2a5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sharp,ls010b7dh04.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/sharp,ls010b7dh04.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sharp Memory LCD panels + +maintainers: + - Alex Lanzano <lanzano.alex@gmail.com> + +description: + Sharp Memory LCDs are a series of monochrome displays that operate over + a SPI bus. The displays require a signal (VCOM) to be generated to prevent + DC bias build up resulting in pixels being unable to change. Three modes + can be used to provide the VCOM signal ("software", "external", "pwm"). + +properties: + compatible: + enum: + - sharp,ls010b7dh04 + - sharp,ls011b7dh03 + - sharp,ls012b7dd01 + - sharp,ls013b7dh03 + - sharp,ls013b7dh05 + - sharp,ls018b7dh02 + - sharp,ls027b7dh01 + - sharp,ls027b7dh01a + - sharp,ls032b7dd02 + - sharp,ls044q7dh01 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 2000000 + + sharp,vcom-mode: + $ref: /schemas/types.yaml#/definitions/string + description: | + software - This mode relies on a software operation to send a + "maintain display" message to the display, toggling the vcom + bit on and off with each message + + external - This mode relies on an external clock to generate + the signal on the EXTCOMM pin + + pwm - This mode relies on a pwm device to generate the signal + on the EXTCOMM pin + + enum: [software, external, pwm] + + enable-gpios: true + + pwms: + maxItems: 1 + description: External VCOM signal + +required: + - compatible + - reg + - sharp,vcom-mode + +allOf: + - $ref: panel/panel-common.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + + - if: + properties: + sharp,vcom-mode: + const: pwm + then: + required: + - pwms + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + display@0 { + compatible = "sharp,ls013b7dh03"; + reg = <0>; + spi-cs-high; + spi-max-frequency = <1000000>; + sharp,vcom-mode = "software"; + }; + }; +... diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml index 278399adc550..735c7f06c24e 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml +++ b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml @@ -26,6 +26,7 @@ properties: - renesas,r9a07g054-mali - rockchip,px30-mali - rockchip,rk3568-mali + - rockchip,rk3576-mali - const: arm,mali-bifrost # Mali Bifrost GPU model/revision is fully discoverable - items: - enum: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index b0531b935b3e..715663b450f8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -756,6 +756,8 @@ patternProperties: description: Japan Display Inc. "^jedec,.*": description: JEDEC Solid State Technology Association + "^jenson,.*": + description: Jenson Display Co. Ltd. "^jesurun,.*": description: Shenzhen Jesurun Electronics Business Dept. "^jethome,.*": |