1 files changed, 0 insertions, 86 deletions
diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt
deleted file mode 100644
index bd863bd69501..000000000000
--- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt
+++ /dev/null
@@ -1,86 +0,0 @@
-Texas Instruments McASP controller
-
-Required properties:
-- compatible :
-	"ti,dm646x-mcasp-audio"	: for DM646x platforms
-	"ti,da830-mcasp-audio"	: for both DA830 & DA850 platforms
-	"ti,am33xx-mcasp-audio"	: for AM33xx platforms (AM33xx, AM43xx, TI81xx)
-	"ti,dra7-mcasp-audio"	: for DRA7xx platforms
-	"ti,omap4-mcasp-audio"	: for OMAP4
-
-- reg : Should contain reg specifiers for the entries in the reg-names property.
-- reg-names : Should contain:
-         * "mpu" for the main registers (required). For compatibility with
-           existing software, it is recommended this is the first entry.
-         * "dat" for separate data port register access (optional).
-- op-mode : I2S/DIT ops mode. 0 for I2S mode. 1 for DIT mode used for S/PDIF,
-  	    IEC60958-1, and AES-3 formats.
-- tdm-slots : Slots for TDM operation. Indicates number of channels transmitted
-  	      or received over one serializer.
-- serial-dir : A list of serializer configuration. Each entry is a number
-               indication for serializer pin direction.
-               (0 - INACTIVE, 1 - TX, 2 - RX)
-- dmas: two element list of DMA controller phandles and DMA request line
-        ordered pairs.
-- dma-names: identifier string for each DMA request line in the dmas property.
-	     These strings correspond 1:1 with the ordered pairs in dmas. The dma
-	     identifiers must be "rx" and "tx".
-
-Optional properties:
-
-- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0
-- tx-num-evt : FIFO levels.
-- rx-num-evt : FIFO levels.
-- dismod : Specify the drive on TX pin during inactive slots
-	0 : 3-state
-	2 : logic low
-	3 : logic high
-	Defaults to 'logic low' when the property is not present
-- sram-size-playback : size of sram to be allocated during playback
-- sram-size-capture  : size of sram to be allocated during capture
-- interrupts : Interrupt numbers for McASP
-- interrupt-names : Known interrupt names are "tx" and "rx"
-- pinctrl-0: Should specify pin control group used for this controller.
-- pinctrl-names: Should contain only one value - "default", for more details
-  		 please refer to pinctrl-bindings.txt
-- fck_parent : Should contain a valid clock name which will be used as parent
-	       for the McASP fck
-- auxclk-fs-ratio: When McASP is bus master indicates the ratio between AUCLK
-		   and FS rate if applicable:
-		   AUCLK rate = auxclk-fs-ratio * FS rate
-
-Optional GPIO support:
-If any McASP pin need to be used as GPIO then the McASP node must have:
-...
-  gpio-controller
-  #gpio-cells = <2>;
-...
-
-When requesting a GPIO, the first parameter is the PIN index in McASP_P*
-registers.
-For example to request the AXR2 pin of mcasp8:
-function-gpios = <&mcasp8 2 0>;
-
-Or to request the ACLKR pin of mcasp8:
-function-gpios = <&mcasp8 29 0>;
-
-For generic gpio information, please refer to bindings/gpio/gpio.txt
-
-Example:
-
-mcasp0: mcasp0@1d00000 {
-	compatible = "ti,da830-mcasp-audio";
-	reg = <0x100000 0x3000>;
-	reg-names "mpu";
-	interrupts = <82>, <83>;
-	interrupt-names = "tx", "rx";
-	op-mode = <0>;		/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	serial-dir = <
-			0 0 0 0	/* 0: INACTIVE, 1: TX, 2: RX */
-			0 0 0 0
-			0 0 0 1
-			2 0 0 0 >;
-	tx-num-evt = <1>;
-	rx-num-evt = <1>;
-};