diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/max77693.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/max77693.txt | 194 |
1 files changed, 0 insertions, 194 deletions
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt deleted file mode 100644 index 1032df14498b..000000000000 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ /dev/null @@ -1,194 +0,0 @@ -Maxim MAX77693 multi-function device - -MAX77693 is a Multifunction device with the following submodules: -- PMIC, -- CHARGER, -- LED, -- MUIC, -- HAPTIC - -It is interfaced to host controller using i2c. -This document describes the bindings for the mfd device. - -Required properties: -- compatible : Must be "maxim,max77693". -- reg : Specifies the i2c slave address of PMIC block. -- interrupts : This i2c device has an IRQ line connected to the main SoC. - -Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnode - named "regulators" using the following format. - - regulators { - regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constraints[*]. - }; - - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - -- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide - users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the appropriate level of feedback. - - Required properties: - - compatible : Must be "maxim,max77693-haptic" - - haptic-supply : power supply for the haptic motor - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - - pwms : phandle to the physical PWM(Pulse Width Modulation) device. - PWM properties should be named "pwms". And number of cell is different - for each pwm device. - To get more information, please refer to documentation. - [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - -- charger : Node configuring the charger driver. - If present, required properties: - - compatible : Must be "maxim,max77693-charger". - - Optional properties (if not set, defaults will be used): - - maxim,constant-microvolt : Battery constant voltage in uV. The charger - will operate in fast charge constant current mode till battery voltage - reaches this level. Then the charger will switch to fast charge constant - voltage mode. Also vsys (system voltage) will be set to this value when - DC power is supplied but charger is not enabled. - Valid values: 3650000 - 4400000, step by 25000 (rounded down) - Default: 4200000 - - - maxim,min-system-microvolt : Minimal system voltage in uV. - Valid values: 3000000 - 3700000, step by 100000 (rounded down) - Default: 3600000 - - - maxim,thermal-regulation-celsius : Temperature in Celsius for entering - high temperature charging mode. If die temperature exceeds this value - the charging current will be reduced by 105 mA/Celsius. - Valid values: 70, 85, 100, 115 - Default: 100 - - - maxim,battery-overcurrent-microamp : Overcurrent protection threshold - in uA (current from battery to system). - Valid values: 2000000 - 3500000, step by 250000 (rounded down) - Default: 3500000 - - - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for - triggering input voltage regulation loop. If input voltage decreases - below this value, the input current will be reduced to reach the - threshold voltage. - Valid values: 4300000, 4700000, 4800000, 4900000 - Default: 4300000 - -- led : the LED submodule device node - -There are two LED outputs available - FLED1 and FLED2. Each of them can -control a separate LED or they can be connected together to double -the maximum current for a single connected LED. One LED is represented -by one child node. - -Required properties: -- compatible : Must be "maxim,max77693-led". - -Optional properties: -- maxim,boost-mode : - In boost mode the device can produce up to 1.2A of total current - on both outputs. The maximum current on each output is reduced - to 625mA then. If not enabled explicitly, boost setting defaults to - LEDS_BOOST_FIXED in case both current sources are used. - Possible values: - LEDS_BOOST_OFF (0) - no boost, - LEDS_BOOST_ADAPTIVE (1) - adaptive mode, - LEDS_BOOST_FIXED (2) - fixed mode. -- maxim,boost-mvout : Output voltage of the boost module in millivolts. - Valid values: 3300 - 5500, step by 25 (rounded down) - Default: 3300 -- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired - if chip estimates that system voltage could drop below this level due - to flash power consumption. - Valid values: 2400 - 3400, step by 33 (rounded down) - Default: 2400 - -Required properties for the LED child node: -- led-sources : see Documentation/devicetree/bindings/leds/common.txt; - device current output identifiers: 0 - FLED1, 1 - FLED2 -- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt - Valid values for a LED connected to one FLED output: - 15625 - 250000, step by 15625 (rounded down) - Valid values for a LED connected to both FLED outputs: - 15625 - 500000, step by 15625 (rounded down) -- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt - Valid values for a single LED connected to one FLED output - (boost mode must be turned off): - 15625 - 1000000, step by 15625 (rounded down) - Valid values for a single LED connected to both FLED outputs: - 15625 - 1250000, step by 15625 (rounded down) - Valid values for two LEDs case: - 15625 - 625000, step by 15625 (rounded down) -- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt - Valid values: 62500 - 1000000, step by 62500 (rounded down) - -Optional properties for the LED child node: -- label : see Documentation/devicetree/bindings/leds/common.txt - -Optional nodes: -- max77693-muic : - Node used only by extcon consumers. - Required properties: - - compatible : "maxim,max77693-muic" - -Example: -#include <dt-bindings/leds/common.h> - - max77693@66 { - compatible = "maxim,max77693"; - reg = <0x66>; - interrupt-parent = <&gpx1>; - interrupts = <5 IRQ_TYPE_LEVEL_LOW>; - - regulators { - esafeout@1 { - regulator-compatible = "ESAFEOUT1"; - regulator-name = "ESAFEOUT1"; - regulator-boot-on; - }; - esafeout@2 { - regulator-compatible = "ESAFEOUT2"; - regulator-name = "ESAFEOUT2"; - }; - charger@0 { - regulator-compatible = "CHARGER"; - regulator-name = "CHARGER"; - regulator-min-microamp = <60000>; - regulator-max-microamp = <2580000>; - regulator-boot-on; - }; - }; - - haptic { - compatible = "maxim,max77693-haptic"; - haptic-supply = <&haptic_supply>; - pwms = <&pwm 0 40000 0>; - pwm-names = "haptic"; - }; - - charger { - compatible = "maxim,max77693-charger"; - - maxim,constant-microvolt = <4200000>; - maxim,min-system-microvolt = <3600000>; - maxim,thermal-regulation-celsius = <75>; - maxim,battery-overcurrent-microamp = <3000000>; - maxim,charge-input-threshold-microvolt = <4300000>; - }; - - led { - compatible = "maxim,max77693-led"; - maxim,boost-mode = <LEDS_BOOST_FIXED>; - maxim,boost-mvout = <5000>; - maxim,mvsys-min = <2400>; - - camera_flash: flash-led { - label = "max77693-flash"; - led-sources = <0>, <1>; - led-max-microamp = <500000>; - flash-max-microamp = <1250000>; - flash-max-timeout-us = <1000000>; - }; - }; - }; |