path: root/drivers/parport/parport_ip32.c

// SPDX-License-Identifier: GPL-2.0-or-later
/* Low-level parallel port routines for built-in port on SGI IP32
 *
 * Author: Arnaud Giersch <arnaud.giersch@free.fr>
 *
 * Based on parport_pc.c by
 *	Phil Blundell, Tim Waugh, Jose Renau, David Campbell,
 *	Andrea Arcangeli, et al.
 *
 * Thanks to Ilya A. Volynets-Evenbakh for his help.
 *
 * Copyright (C) 2005, 2006 Arnaud Giersch.
 */

/* Current status:
 *
 *	Basic SPP and PS2 modes are supported.
 *	Support for parallel port IRQ is present.
 *	Hardware SPP (a.k.a. compatibility), EPP, and ECP modes are
 *	supported.
 *	SPP/ECP FIFO can be driven in PIO or DMA mode.  PIO mode can work with
 *	or without interrupt support.
 *
 *	Hardware ECP mode is not fully implemented (ecp_read_data and
 *	ecp_write_addr are actually missing).
 *
 * To do:
 *
 *	Fully implement ECP mode.
 *	EPP and ECP mode need to be tested.  I currently do not own any
 *	peripheral supporting these extended mode, and cannot test them.
 *	If DMA mode works well, decide if support for PIO FIFO modes should be
 *	dropped.
 *	Use the io{read,write} family functions when they become available in
 *	the linux-mips.org tree.  Note: the MIPS specific functions readsb()
 *	and writesb() are to be translated by ioread8_rep() and iowrite8_rep()
 *	respectively.
 */

/* The built-in parallel port on the SGI 02 workstation (a.k.a. IP32) is an
 * IEEE 1284 parallel port driven by a Texas Instrument TL16PIR552PH chip[1].
 * This chip supports SPP, bidirectional, EPP and ECP modes.  It has a 16 byte
 * FIFO buffer and supports DMA transfers.
 *
 * [1] http://focus.ti.com/docs/prod/folders/print/tl16pir552.html
 *
 * Theoretically, we could simply use the parport_pc module.  It is however
 * not so simple.  The parport_pc code assumes that the parallel port
 * registers are port-mapped.  On the O2, they are memory-mapped.
 * Furthermore, each register is replicated on 256 consecutive addresses (as
 * it is for the built-in serial ports on the same chip).
 */

/*--- Some configuration defines ---------------------------------------*/

/* DEBUG_PARPORT_IP32
 *	0	disable debug
 *	1	standard level: pr_debug1 is enabled
 *	2	parport_ip32_dump_state is enabled
 *	>=3	verbose level: pr_debug is enabled
 */
#if !defined(DEBUG_PARPORT_IP32)
#	define DEBUG_PARPORT_IP32  0	/* 0 (disabled) for production */
#endif

/*----------------------------------------------------------------------*/

/* Setup DEBUG macros.  This is done before any includes, just in case we
 * activate pr_debug() with DEBUG_PARPORT_IP32 >= 3.
 */
#if DEBUG_PARPORT_IP32 == 1
#	warning DEBUG_PARPORT_IP32 == 1
#elif DEBUG_PARPORT_IP32 == 2
#	warning DEBUG_PARPORT_IP32 == 2
#elif DEBUG_PARPORT_IP32 >= 3
#	warning DEBUG_PARPORT_IP32 >= 3
#	if !defined(DEBUG)
#		define DEBUG /* enable pr_debug() in kernel.h */
#	endif
#endif

#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/parport.h>
#include <linux/sched/signal.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/stddef.h>
#include <linux/types.h>
#include <asm/io.h>
#include <asm/ip32/ip32_ints.h>
#include <asm/ip32/mace.h>

/*--- Global variables -------------------------------------------------*/

/* Verbose probing on by default for debugging. */
#if DEBUG_PARPORT_IP32 >= 1
#	define DEFAULT_VERBOSE_PROBING	1
#else
#	define DEFAULT_VERBOSE_PROBING	0
#endif

/* Default prefix for printk */
#define PPIP32 "parport_ip32: "

/*
 * These are the module parameters:
 * @features:		bit mask of features to enable/disable
 *			(all enabled by default)
 * @verbose_probing:	log chit-chat during initialization
 */
#define PARPORT_IP32_ENABLE_IRQ	(1U << 0)
#define PARPORT_IP32_ENABLE_DMA	(1U << 1)
#define PARPORT_IP32_ENABLE_SPP	(1U << 2)
#define PARPORT_IP32_ENABLE_EPP	(1U << 3)
#define PARPORT_IP32_ENABLE_ECP	(1U << 4)
static unsigned int features =	~0U;
static bool verbose_probing =	DEFAULT_VERBOSE_PROBING;

/* We do not support more than one port. */
static struct parport *this_port;

/* Timing constants for FIFO modes.  */
#define FIFO_NFAULT_TIMEOUT	100	/* milliseconds */
#define FIFO_POLLING_INTERVAL	50	/* microseconds */

/*--- I/O register definitions -----------------------------------------*/

/**
 * struct parport_ip32_regs - virtual addresses of parallel port registers
 * @data:	Data Register
 * @dsr:	Device Status Register
 * @dcr:	Device Control Register
 * @eppAddr:	EPP Address Register
 * @eppData0:	EPP Data Register 0
 * @eppData1:	EPP Data Register 1
 * @eppData2:	EPP Data Register 2
 * @eppData3:	EPP Data Register 3
 * @ecpAFifo:	ECP Address FIFO
 * @fifo:	General FIFO register.  The same address is used for:
 *		- cFifo, the Parallel Port DATA FIFO
 *		- ecpDFifo, the ECP Data FIFO
 *		- tFifo, the ECP Test FIFO
 * @cnfgA:	Configuration Register A
 * @cnfgB:	Configuration Register B
 * @ecr:	Extended Control Register
 */
struct parport_ip32_regs {
	void __iomem *data;
	void __iomem *dsr;
	void __iomem *dcr;
	void __iomem *eppAddr;
	void __iomem *eppData0;
	void __iomem *eppData1;
	void __iomem *eppData2;
	void __iomem *eppData3;
	void __iomem *ecpAFifo;
	void __iomem *fifo;
	void __iomem *cnfgA;
	void __iomem *cnfgB;
	void __iomem *ecr;
};

/* Device Status Register */
#define DSR_nBUSY		(1U << 7)	/* PARPORT_STATUS_BUSY */
#define DSR_nACK		(1U << 6)	/* PARPORT_STATUS_ACK */
#define DSR_PERROR		(1U << 5)	/* PARPORT_STATUS_PAPEROUT */
#define DSR_SELECT		(1U << 4)	/* PARPORT_STATUS_SELECT */
#define DSR_nFAULT		(1U << 3)	/* PARPORT_STATUS_ERROR */
#define DSR_nPRINT		(1U << 2)	/* specific to TL16PIR552 */
/* #define DSR_reserved		(1U << 1) */
#define DSR_TIMEOUT		(1U << 0)	/* EPP timeout */

/* Device Control Register */
/* #define DCR_reserved		(1U << 7) | (1U <<  6) */
#define DCR_DIR			(1U << 5)	/* direction */
#define DCR_IRQ			(1U << 4)	/* interrupt on nAck */
#define DCR_SELECT		(1U << 3)	/* PARPORT_CONTROL_SELECT */
#define DCR_nINIT		(1U << 2)	/* PARPORT_CONTROL_INIT */
#define DCR_AUTOFD		(1U << 1)	/* PARPORT_CONTROL_AUTOFD */
#define DCR_STROBE		(1U << 0)	/* PARPORT_CONTROL_STROBE */

/* ECP Configuration Register A */
#define CNFGA_IRQ		(1U << 7)
#define CNFGA_ID_MASK		((1U << 6) | (1U << 5) | (1U << 4))
#define CNFGA_ID_SHIFT		4
#define CNFGA_ID_16		(00U << CNFGA_ID_SHIFT)
#define CNFGA_ID_8		(01U << CNFGA_ID_SHIFT)
#define CNFGA_ID_32		(02U << CNFGA_ID_SHIFT)
/* #define CNFGA_reserved	(1U << 3) */
#define CNFGA_nBYTEINTRANS	(1U << 2)
#define CNFGA_PWORDLEFT		((1U << 1) | (1U << 0))

/* ECP Configuration Register B */
#define CNFGB_COMPRESS		(1U << 7)
#define CNFGB_INTRVAL		(1U << 6)
#define CNFGB_IRQ_MASK		((1U << 5) | (1U << 4) | (1U << 3))
#define CNFGB_IRQ_SHIFT		3
#define CNFGB_DMA_MASK		((1U << 2) | (1U << 1) | (1U << 0))
#define CNFGB_DMA_SHIFT		0

/* Extended Control Register */
#define ECR_MODE_MASK		((1U << 7) | (1U << 6) | (1U << 5))
#define ECR_MODE_SHIFT		5
#define ECR_MODE_SPP		(00U << ECR_MODE_SHIFT)
#define ECR_MODE_PS2		(01U << ECR_MODE_SHIFT)
#define ECR_MODE_PPF		(02U << ECR_MODE_SHIFT)
#define ECR_MODE_ECP		(03U << ECR_MODE_SHIFT)
#define ECR_MODE_EPP		(04U << ECR_MODE_SHIFT)
/* #define ECR_MODE_reserved	(05U << ECR_MODE_SHIFT) */
#define ECR_MODE_TST		(06U << ECR_MODE_SHIFT)
#define ECR_MODE_CFG		(07U << ECR_MODE_SHIFT)
#define ECR_nERRINTR		(1U << 4)
#define ECR_DMAEN		(1U << 3)
#define ECR_SERVINTR		(1U << 2)
#define ECR_F_FULL		(1U << 1)
#define ECR_F_EMPTY		(1U << 0)

/*--- Private data -----------------------------------------------------*/

/**
 * enum parport_ip32_irq_mode - operation mode of interrupt handler
 * @PARPORT_IP32_IRQ_FWD:	forward interrupt to the upper parport layer
 * @PARPORT_IP32_IRQ_HERE:	interrupt is handled locally
 */
enum parport_ip32_irq_mode { PARPORT_IP32_IRQ_FWD, PARPORT_IP32_IRQ_HERE };

/**
 * struct parport_ip32_private - private stuff for &struct parport
 * @regs:		register addresses
 * @dcr_cache:		cached contents of DCR
 * @dcr_writable:	bit mask of writable DCR bits
 * @pword:		number of bytes per PWord
 * @fifo_depth:		number of PWords that FIFO will hold
 * @readIntrThreshold:	minimum number of PWords we can read
 *			if we get an interrupt
 * @writeIntrThreshold:	minimum number of PWords we can write
 *			if we get an interrupt
 * @irq_mode:		operation mode of interrupt handler for this port
 * @irq_complete:	mutex used to wait for an interrupt to occur
 */
struct parport_ip32_private {
	struct parport_ip32_regs	regs;
	unsigned int			dcr_cache;
	unsigned int			dcr_writable;
	unsigned int			pword;
	unsigned int			fifo_depth;
	unsigned int			readIntrThreshold;
	unsigned int			writeIntrThreshold;
	enum parport_ip32_irq_mode	irq_mode;
	struct completion		irq_complete;
};

/*--- Debug code -------------------------------------------------------*/

/*
 * pr_debug1 - print debug messages
 *
 * This is like pr_debug(), but is defined for %DEBUG_PARPORT_IP32 >= 1
 */
#if DEBUG_PARPORT_IP32 >= 1
#	define pr_debug1(...)	printk(KERN_DEBUG __VA_ARGS__)
#else /* DEBUG_PARPORT_IP32 < 1 */
#	define pr_debug1(...)	do { } while (0)
#endif

/*
 * pr_trace, pr_trace1 - trace function calls
 * @p:		pointer to &struct parport
 * @fmt:	printk format string
 * @...:	parameters for format string
 *
 * Macros used to trace function calls.  The given string is formatted after
 * function name.  pr_trace() uses pr_debug(), and pr_trace1() uses
 * pr_debug1().  __pr_trace() is the low-level macro and is not to be used
 * directly.
 */
#define __pr_trace(pr, p, fmt, ...)					\
	pr("%s: %s" fmt "\n",						\
	   ({ const struct parport *__p = (p);				\
		   __p ? __p->name : "parport_ip32"; }),		\
	   __func__ , ##__VA_ARGS__)
#define pr_trace(p, fmt, ...)	__pr_trace(pr_debug, p, fmt , ##__VA_ARGS__)
#define pr_trace1(p, fmt, ...)	__pr_trace(pr_debug1, p, fmt , ##__VA_ARGS__)

/*
 * __pr_probe, pr_probe - print message if @verbose_probing is true
 * @p:		pointer to &struct parport
 * @fmt:	printk format string
 * @...:	parameters for format string
 *
 * For new lines, use pr_probe().  Use __pr_probe() for continued lines.
 */
#define __pr_probe(...)							\
	do { if (verbose_probing) printk(__VA_ARGS__); } while (0)
#define pr_probe(p, fmt, ...)						\
	__pr_probe(KERN_INFO PPIP32 "0x%lx: " fmt, (p)->base , ##__VA_ARGS__)

/*
 * parport_ip32_dump_state - print register status of parport
 * @p:		pointer to &struct parport
 * @str:	string to add in message
 * @show_ecp_config:	shall we dump ECP configuration registers too?
 *
 * This function is only here for debugging purpose, and should be used with
 * care.  Reading the parallel port registers may have undesired side effects.
 * Especially if @show_ecp_config is true, the parallel port is resetted.
 * This function is only defined if %DEBUG_PARPORT_IP32 >= 2.
 */
#if DEBUG_PARPORT_IP32 >= 2
static void parport_ip32_dump_state(struct parport *p, char *str,
				    unsigned int show_ecp_config)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	unsigned int i;

	printk(KERN_DEBUG PPIP32 "%s: state (%s):\n", p->name, str);
	{
		static const char ecr_modes[8][4] = {"SPP", "PS2", "PPF",
						     "ECP", "EPP", "???",
						     "TST", "CFG"};
		unsigned int ecr = readb(priv->regs.ecr);
		printk(KERN_DEBUG PPIP32 "    ecr=0x%02x", ecr);
		pr_cont(" %s",
			ecr_modes[(ecr & ECR_MODE_MASK) >> ECR_MODE_SHIFT]);
		if (ecr & ECR_nERRINTR)
			pr_cont(",nErrIntrEn");
		if (ecr & ECR_DMAEN)
			pr_cont(",dmaEn");
		if (ecr & ECR_SERVINTR)
			pr_cont(",serviceIntr");
		if (ecr & ECR_F_FULL)
			pr_cont(",f_full");
		if (ecr & ECR_F_EMPTY)
			pr_cont(",f_empty");
		pr_cont("\n");
	}
	if (show_ecp_config) {
		unsigned int oecr, cnfgA, cnfgB;
		oecr = readb(priv->regs.ecr);
		writeb(ECR_MODE_PS2, priv->regs.ecr);
		writeb(ECR_MODE_CFG, priv->regs.ecr);
		cnfgA = readb(priv->regs.cnfgA);
		cnfgB = readb(priv->regs.cnfgB);
		writeb(ECR_MODE_PS2, priv->regs.ecr);
		writeb(oecr, priv->regs.ecr);
		printk(KERN_DEBUG PPIP32 "    cnfgA=0x%02x", cnfgA);
		pr_cont(" ISA-%s", (cnfgA & CNFGA_IRQ) ? "Level" : "Pulses");
		switch (cnfgA & CNFGA_ID_MASK) {
		case CNFGA_ID_8:
			pr_cont(",8 bits");
			break;
		case CNFGA_ID_16:
			pr_cont(",16 bits");
			break;
		case CNFGA_ID_32:
			pr_cont(",32 bits");
			break;
		default:
			pr_cont(",unknown ID");
			break;
		}
		if (!(cnfgA & CNFGA_nBYTEINTRANS))
			pr_cont(",ByteInTrans");
		if ((cnfgA & CNFGA_ID_MASK) != CNFGA_ID_8)
			pr_cont(",%d byte%s left",
				cnfgA & CNFGA_PWORDLEFT,
				((cnfgA & CNFGA_PWORDLEFT) > 1) ? "s" : "");
		pr_cont("\n");
		printk(KERN_DEBUG PPIP32 "    cnfgB=0x%02x", cnfgB);
		pr_cont(" irq=%u,dma=%u",
			(cnfgB & CNFGB_IRQ_MASK) >> CNFGB_IRQ_SHIFT,
			(cnfgB & CNFGB_DMA_MASK) >> CNFGB_DMA_SHIFT);
		pr_cont(",intrValue=%d", !!(cnfgB & CNFGB_INTRVAL));
		if (cnfgB & CNFGB_COMPRESS)
			pr_cont(",compress");
		pr_cont("\n");
	}
	for (i = 0; i < 2; i++) {
		unsigned int dcr = i ? priv->dcr_cache : readb(priv->regs.dcr);
		printk(KERN_DEBUG PPIP32 "    dcr(%s)=0x%02x",
		       i ? "soft" : "hard", dcr);
		pr_cont(" %s", (dcr & DCR_DIR) ? "rev" : "fwd");
		if (dcr & DCR_IRQ)
			pr_cont(",ackIntEn");
		if (!(dcr & DCR_SELECT))
			pr_cont(",nSelectIn");
		if (dcr & DCR_nINIT)
			pr_cont(",nInit");
		if (!(dcr & DCR_AUTOFD))
			pr_cont(",nAutoFD");
		if (!(dcr & DCR_STROBE))
			pr_cont(",nStrobe");
		pr_cont("\n");
	}
#define sep (f++ ? ',' : ' ')
	{
		unsigned int f = 0;
		unsigned int dsr = readb(priv->regs.dsr);
		printk(KERN_DEBUG PPIP32 "    dsr=0x%02x", dsr);
		if (!(dsr & DSR_nBUSY))
			pr_cont("%cBusy", sep);
		if (dsr & DSR_nACK)
			pr_cont("%cnAck", sep);
		if (dsr & DSR_PERROR)
			pr_cont("%cPError", sep);
		if (dsr & DSR_SELECT)
			pr_cont("%cSelect", sep);
		if (dsr & DSR_nFAULT)
			pr_cont("%cnFault", sep);
		if (!(dsr & DSR_nPRINT))
			pr_cont("%c(Print)", sep);
		if (dsr & DSR_TIMEOUT)
			pr_cont("%cTimeout", sep);
		pr_cont("\n");
	}
#undef sep
}
#else /* DEBUG_PARPORT_IP32 < 2 */
#define parport_ip32_dump_state(...)	do { } while (0)
#endif

/*
 * CHECK_EXTRA_BITS - track and log extra bits
 * @p:		pointer to &struct parport
 * @b:		byte to inspect
 * @m:		bit mask of authorized bits
 *
 * This is used to track and log extra bits that should not be there in
 * parport_ip32_write_control() and parport_ip32_frob_control().  It is only
 * defined if %DEBUG_PARPORT_IP32 >= 1.
 */
#if DEBUG_PARPORT_IP32 >= 1
#define CHECK_EXTRA_BITS(p, b, m)					\
	do {								\
		unsigned int __b = (b), __m = (m);			\
		if (__b & ~__m)						\
			pr_debug1(PPIP32 "%s: extra bits in %s(%s): "	\
				  "0x%02x/0x%02x\n",			\
				  (p)->name, __func__, #b, __b, __m);	\
	} while (0)
#else /* DEBUG_PARPORT_IP32 < 1 */
#define CHECK_EXTRA_BITS(...)	do { } while (0)
#endif

/*--- IP32 parallel port DMA operations --------------------------------*/

/**
 * struct parport_ip32_dma_data - private data needed for DMA operation
 * @dir:	DMA direction (from or to device)
 * @buf:	buffer physical address
 * @len:	buffer length
 * @next:	address of next bytes to DMA transfer
 * @left:	number of bytes remaining
 * @ctx:	next context to write (0: context_a; 1: context_b)
 * @irq_on:	are the DMA IRQs currently enabled?
 * @lock:	spinlock to protect access to the structure
 */
struct parport_ip32_dma_data {
	enum dma_data_direction		dir;
	dma_addr_t			buf;
	dma_addr_t			next;
	size_t				len;
	size_t				left;
	unsigned int			ctx;
	unsigned int			irq_on;
	spinlock_t			lock;
};
static struct parport_ip32_dma_data parport_ip32_dma;

/**
 * parport_ip32_dma_setup_context - setup next DMA context
 * @limit:	maximum data size for the context
 *
 * The alignment constraints must be verified in caller function, and the
 * parameter @limit must be set accordingly.
 */
static void parport_ip32_dma_setup_context(unsigned int limit)
{
	unsigned long flags;

	spin_lock_irqsave(&parport_ip32_dma.lock, flags);
	if (parport_ip32_dma.left > 0) {
		/* Note: ctxreg is "volatile" here only because
		 * mace->perif.ctrl.parport.context_a and context_b are
		 * "volatile".  */
		volatile u64 __iomem *ctxreg = (parport_ip32_dma.ctx == 0) ?
			&mace->perif.ctrl.parport.context_a :
			&mace->perif.ctrl.parport.context_b;
		u64 count;
		u64 ctxval;
		if (parport_ip32_dma.left <= limit) {
			count = parport_ip32_dma.left;
			ctxval = MACEPAR_CONTEXT_LASTFLAG;
		} else {
			count = limit;
			ctxval = 0;
		}

		pr_trace(NULL,
			 "(%u): 0x%04x:0x%04x, %u -> %u%s",
			 limit,
			 (unsigned int)parport_ip32_dma.buf,
			 (unsigned int)parport_ip32_dma.next,
			 (unsigned int)count,
			 parport_ip32_dma.ctx, ctxval ? "*" : "");

		ctxval |= parport_ip32_dma.next &
			MACEPAR_CONTEXT_BASEADDR_MASK;
		ctxval |= ((count - 1) << MACEPAR_CONTEXT_DATALEN_SHIFT) &
			MACEPAR_CONTEXT_DATALEN_MASK;
		writeq(ctxval, ctxreg);
		parport_ip32_dma.next += count;
		parport_ip32_dma.left -= count;
		parport_ip32_dma.ctx ^= 1U;
	}
	/* If there is nothing more to send, disable IRQs to avoid to
	 * face an IRQ storm which can lock the machine.  Disable them
	 * only once. */
	if (parport_ip32_dma.left == 0 && parport_ip32_dma.irq_on) {
		pr_debug(PPIP32 "IRQ off (ctx)\n");
		disable_irq_nosync(MACEISA_PAR_CTXA_IRQ);
		disable_irq_nosync(MACEISA_PAR_CTXB_IRQ);
		parport_ip32_dma.irq_on = 0;
	}
	spin_unlock_irqrestore(&parport_ip32_dma.lock, flags);
}

/**
 * parport_ip32_dma_interrupt - DMA interrupt handler
 * @irq:	interrupt number
 * @dev_id:	unused
 */
static irqreturn_t parport_ip32_dma_interrupt(int irq, void *dev_id)
{
	if (parport_ip32_dma.left)
		pr_trace(NULL, "(%d): ctx=%d", irq, parport_ip32_dma.ctx);
	parport_ip32_dma_setup_context(MACEPAR_CONTEXT_DATA_BOUND);
	return IRQ_HANDLED;
}

#if DEBUG_PARPORT_IP32
static irqreturn_t parport_ip32_merr_interrupt(int irq, void *dev_id)
{
	pr_trace1(NULL, "(%d)", irq);
	return IRQ_HANDLED;
}
#endif

/**
 * parport_ip32_dma_start - begins a DMA transfer
 * @p:		partport to work on
 * @dir:	DMA direction: DMA_TO_DEVICE or DMA_FROM_DEVICE
 * @addr:	pointer to data buffer
 * @count:	buffer size
 *
 * Calls to parport_ip32_dma_start() and parport_ip32_dma_stop() must be
 * correctly balanced.
 */
static int parport_ip32_dma_start(struct parport *p,
		enum dma_data_direction dir, void *addr, size_t count)
{
	unsigned int limit;
	u64 ctrl;

	pr_trace(NULL, "(%d, %lu)", dir, (unsigned long)count);

	/* FIXME - add support for DMA_FROM_DEVICE.  In this case, buffer must
	 * be 64 bytes aligned. */
	BUG_ON(dir != DMA_TO_DEVICE);

	/* Reset DMA controller */
	ctrl = MACEPAR_CTLSTAT_RESET;
	writeq(ctrl, &mace->perif.ctrl.parport.cntlstat);

	/* DMA IRQs should normally be enabled */
	if (!parport_ip32_dma.irq_on) {
		WARN_ON(1);
		enable_irq(MACEISA_PAR_CTXA_IRQ);
		enable_irq(MACEISA_PAR_CTXB_IRQ);
		parport_ip32_dma.irq_on = 1;
	}

	/* Prepare DMA pointers */
	parport_ip32_dma.dir = dir;
	parport_ip32_dma.buf = dma_map_single(&p->bus_dev, addr, count, dir);
	parport_ip32_dma.len = count;
	parport_ip32_dma.next = parport_ip32_dma.buf;
	parport_ip32_dma.left = parport_ip32_dma.len;
	parport_ip32_dma.ctx = 0;

	/* Setup DMA direction and first two contexts */
	ctrl = (dir == DMA_TO_DEVICE) ? 0 : MACEPAR_CTLSTAT_DIRECTION;
	writeq(ctrl, &mace->perif.ctrl.parport.cntlstat);
	/* Single transfer should not cross a 4K page boundary */
	limit = MACEPAR_CONTEXT_DATA_BOUND -
		(parport_ip32_dma.next & (MACEPAR_CONTEXT_DATA_BOUND - 1));
	parport_ip32_dma_setup_context(limit);
	parport_ip32_dma_setup_context(MACEPAR_CONTEXT_DATA_BOUND);

	/* Real start of DMA transfer */
	ctrl |= MACEPAR_CTLSTAT_ENABLE;
	writeq(ctrl, &mace->perif.ctrl.parport.cntlstat);

	return 0;
}

/**
 * parport_ip32_dma_stop - ends a running DMA transfer
 * @p:		partport to work on
 *
 * Calls to parport_ip32_dma_start() and parport_ip32_dma_stop() must be
 * correctly balanced.
 */
static void parport_ip32_dma_stop(struct parport *p)
{
	u64 ctx_a;
	u64 ctx_b;
	u64 ctrl;
	u64 diag;
	size_t res[2];	/* {[0] = res_a, [1] = res_b} */

	pr_trace(NULL, "()");

	/* Disable IRQs */
	spin_lock_irq(&parport_ip32_dma.lock);
	if (parport_ip32_dma.irq_on) {
		pr_debug(PPIP32 "IRQ off (stop)\n");
		disable_irq_nosync(MACEISA_PAR_CTXA_IRQ);
		disable_irq_nosync(MACEISA_PAR_CTXB_IRQ);
		parport_ip32_dma.irq_on = 0;
	}
	spin_unlock_irq(&parport_ip32_dma.lock);
	/* Force IRQ synchronization, even if the IRQs were disabled
	 * elsewhere. */
	synchronize_irq(MACEISA_PAR_CTXA_IRQ);
	synchronize_irq(MACEISA_PAR_CTXB_IRQ);

	/* Stop DMA transfer */
	ctrl = readq(&mace->perif.ctrl.parport.cntlstat);
	ctrl &= ~MACEPAR_CTLSTAT_ENABLE;
	writeq(ctrl, &mace->perif.ctrl.parport.cntlstat);

	/* Adjust residue (parport_ip32_dma.left) */
	ctx_a = readq(&mace->perif.ctrl.parport.context_a);
	ctx_b = readq(&mace->perif.ctrl.parport.context_b);
	ctrl = readq(&mace->perif.ctrl.parport.cntlstat);
	diag = readq(&mace->perif.ctrl.parport.diagnostic);
	res[0] = (ctrl & MACEPAR_CTLSTAT_CTXA_VALID) ?
		1 + ((ctx_a & MACEPAR_CONTEXT_DATALEN_MASK) >>
		     MACEPAR_CONTEXT_DATALEN_SHIFT) :
		0;
	res[1] = (ctrl & MACEPAR_CTLSTAT_CTXB_VALID) ?
		1 + ((ctx_b & MACEPAR_CONTEXT_DATALEN_MASK) >>
		     MACEPAR_CONTEXT_DATALEN_SHIFT) :
		0;
	if (diag & MACEPAR_DIAG_DMACTIVE)
		res[(diag & MACEPAR_DIAG_CTXINUSE) != 0] =
			1 + ((diag & MACEPAR_DIAG_CTRMASK) >>
			     MACEPAR_DIAG_CTRSHIFT);
	parport_ip32_dma.left += res[0] + res[1];

	/* Reset DMA controller, and re-enable IRQs */
	ctrl = MACEPAR_CTLSTAT_RESET;
	writeq(ctrl, &mace->perif.ctrl.parport.cntlstat);
	pr_debug(PPIP32 "IRQ on (stop)\n");
	enable_irq(MACEISA_PAR_CTXA_IRQ);
	enable_irq(MACEISA_PAR_CTXB_IRQ);
	parport_ip32_dma.irq_on = 1;

	dma_unmap_single(&p->bus_dev, parport_ip32_dma.buf,
			 parport_ip32_dma.len, parport_ip32_dma.dir);
}

/**
 * parport_ip32_dma_get_residue - get residue from last DMA transfer
 *
 * Returns the number of bytes remaining from last DMA transfer.
 */
static inline size_t parport_ip32_dma_get_residue(void)
{
	return parport_ip32_dma.left;
}

/**
 * parport_ip32_dma_register - initialize DMA engine
 *
 * Returns zero for success.
 */
static int parport_ip32_dma_register(void)
{
	int err;

	spin_lock_init(&parport_ip32_dma.lock);
	parport_ip32_dma.irq_on = 1;

	/* Reset DMA controller */
	writeq(MACEPAR_CTLSTAT_RESET, &mace->perif.ctrl.parport.cntlstat);

	/* Request IRQs */
	err = request_irq(MACEISA_PAR_CTXA_IRQ, parport_ip32_dma_interrupt,
			  0, "parport_ip32", NULL);
	if (err)
		goto fail_a;
	err = request_irq(MACEISA_PAR_CTXB_IRQ, parport_ip32_dma_interrupt,
			  0, "parport_ip32", NULL);
	if (err)
		goto fail_b;
#if DEBUG_PARPORT_IP32
	/* FIXME - what is this IRQ for? */
	err = request_irq(MACEISA_PAR_MERR_IRQ, parport_ip32_merr_interrupt,
			  0, "parport_ip32", NULL);
	if (err)
		goto fail_merr;
#endif
	return 0;

#if DEBUG_PARPORT_IP32
fail_merr:
	free_irq(MACEISA_PAR_CTXB_IRQ, NULL);
#endif
fail_b:
	free_irq(MACEISA_PAR_CTXA_IRQ, NULL);
fail_a:
	return err;
}

/**
 * parport_ip32_dma_unregister - release and free resources for DMA engine
 */
static void parport_ip32_dma_unregister(void)
{
#if DEBUG_PARPORT_IP32
	free_irq(MACEISA_PAR_MERR_IRQ, NULL);
#endif
	free_irq(MACEISA_PAR_CTXB_IRQ, NULL);
	free_irq(MACEISA_PAR_CTXA_IRQ, NULL);
}

/*--- Interrupt handlers and associates --------------------------------*/

/**
 * parport_ip32_wakeup - wakes up code waiting for an interrupt
 * @p:		pointer to &struct parport
 */
static inline void parport_ip32_wakeup(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	complete(&priv->irq_complete);
}

/**
 * parport_ip32_interrupt - interrupt handler
 * @irq:	interrupt number
 * @dev_id:	pointer to &struct parport
 *
 * Caught interrupts are forwarded to the upper parport layer if IRQ_mode is
 * %PARPORT_IP32_IRQ_FWD.
 */
static irqreturn_t parport_ip32_interrupt(int irq, void *dev_id)
{
	struct parport * const p = dev_id;
	struct parport_ip32_private * const priv = p->physport->private_data;
	enum parport_ip32_irq_mode irq_mode = priv->irq_mode;

	switch (irq_mode) {
	case PARPORT_IP32_IRQ_FWD:
		return parport_irq_handler(irq, dev_id);

	case PARPORT_IP32_IRQ_HERE:
		parport_ip32_wakeup(p);
		break;
	}

	return IRQ_HANDLED;
}

/*--- Some utility function to manipulate ECR register -----------------*/

/**
 * parport_ip32_read_econtrol - read contents of the ECR register
 * @p:		pointer to &struct parport
 */
static inline unsigned int parport_ip32_read_econtrol(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return readb(priv->regs.ecr);
}

/**
 * parport_ip32_write_econtrol - write new contents to the ECR register
 * @p:		pointer to &struct parport
 * @c:		new value to write
 */
static inline void parport_ip32_write_econtrol(struct parport *p,
					       unsigned int c)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	writeb(c, priv->regs.ecr);
}

/**
 * parport_ip32_frob_econtrol - change bits from the ECR register
 * @p:		pointer to &struct parport
 * @mask:	bit mask of bits to change
 * @val:	new value for changed bits
 *
 * Read from the ECR, mask out the bits in @mask, exclusive-or with the bits
 * in @val, and write the result to the ECR.
 */
static inline void parport_ip32_frob_econtrol(struct parport *p,
					      unsigned int mask,
					      unsigned int val)
{
	unsigned int c;
	c = (parport_ip32_read_econtrol(p) & ~mask) ^ val;
	parport_ip32_write_econtrol(p, c);
}

/**
 * parport_ip32_set_mode - change mode of ECP port
 * @p:		pointer to &struct parport
 * @mode:	new mode to write in ECR
 *
 * ECR is reset in a sane state (interrupts and DMA disabled), and placed in
 * mode @mode.  Go through PS2 mode if needed.
 */
static void parport_ip32_set_mode(struct parport *p, unsigned int mode)
{
	unsigned int omode;

	mode &= ECR_MODE_MASK;
	omode = parport_ip32_read_econtrol(p) & ECR_MODE_MASK;

	if (!(mode == ECR_MODE_SPP || mode == ECR_MODE_PS2
	      || omode == ECR_MODE_SPP || omode == ECR_MODE_PS2)) {
		/* We have to go through PS2 mode */
		unsigned int ecr = ECR_MODE_PS2 | ECR_nERRINTR | ECR_SERVINTR;
		parport_ip32_write_econtrol(p, ecr);
	}
	parport_ip32_write_econtrol(p, mode | ECR_nERRINTR | ECR_SERVINTR);
}

/*--- Basic functions needed for parport -------------------------------*/

/**
 * parport_ip32_read_data - return current contents of the DATA register
 * @p:		pointer to &struct parport
 */
static inline unsigned char parport_ip32_read_data(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return readb(priv->regs.data);
}

/**
 * parport_ip32_write_data - set new contents for the DATA register
 * @p:		pointer to &struct parport
 * @d:		new value to write
 */
static inline void parport_ip32_write_data(struct parport *p, unsigned char d)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	writeb(d, priv->regs.data);
}

/**
 * parport_ip32_read_status - return current contents of the DSR register
 * @p:		pointer to &struct parport
 */
static inline unsigned char parport_ip32_read_status(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return readb(priv->regs.dsr);
}

/**
 * __parport_ip32_read_control - return cached contents of the DCR register
 * @p:		pointer to &struct parport
 */
static inline unsigned int __parport_ip32_read_control(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return priv->dcr_cache; /* use soft copy */
}

/**
 * __parport_ip32_write_control - set new contents for the DCR register
 * @p:		pointer to &struct parport
 * @c:		new value to write
 */
static inline void __parport_ip32_write_control(struct parport *p,
						unsigned int c)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	CHECK_EXTRA_BITS(p, c, priv->dcr_writable);
	c &= priv->dcr_writable; /* only writable bits */
	writeb(c, priv->regs.dcr);
	priv->dcr_cache = c;		/* update soft copy */
}

/**
 * __parport_ip32_frob_control - change bits from the DCR register
 * @p:		pointer to &struct parport
 * @mask:	bit mask of bits to change
 * @val:	new value for changed bits
 *
 * This is equivalent to read from the DCR, mask out the bits in @mask,
 * exclusive-or with the bits in @val, and write the result to the DCR.
 * Actually, the cached contents of the DCR is used.
 */
static inline void __parport_ip32_frob_control(struct parport *p,
					       unsigned int mask,
					       unsigned int val)
{
	unsigned int c;
	c = (__parport_ip32_read_control(p) & ~mask) ^ val;
	__parport_ip32_write_control(p, c);
}

/**
 * parport_ip32_read_control - return cached contents of the DCR register
 * @p:		pointer to &struct parport
 *
 * The return value is masked so as to only return the value of %DCR_STROBE,
 * %DCR_AUTOFD, %DCR_nINIT, and %DCR_SELECT.
 */
static inline unsigned char parport_ip32_read_control(struct parport *p)
{
	const unsigned int rm =
		DCR_STROBE | DCR_AUTOFD | DCR_nINIT | DCR_SELECT;
	return __parport_ip32_read_control(p) & rm;
}

/**
 * parport_ip32_write_control - set new contents for the DCR register
 * @p:		pointer to &struct parport
 * @c:		new value to write
 *
 * The value is masked so as to only change the value of %DCR_STROBE,
 * %DCR_AUTOFD, %DCR_nINIT, and %DCR_SELECT.
 */
static inline void parport_ip32_write_control(struct parport *p,
					      unsigned char c)
{
	const unsigned int wm =
		DCR_STROBE | DCR_AUTOFD | DCR_nINIT | DCR_SELECT;
	CHECK_EXTRA_BITS(p, c, wm);
	__parport_ip32_frob_control(p, wm, c & wm);
}

/**
 * parport_ip32_frob_control - change bits from the DCR register
 * @p:		pointer to &struct parport
 * @mask:	bit mask of bits to change
 * @val:	new value for changed bits
 *
 * This differs from __parport_ip32_frob_control() in that it only allows to
 * change the value of %DCR_STROBE, %DCR_AUTOFD, %DCR_nINIT, and %DCR_SELECT.
 */
static inline unsigned char parport_ip32_frob_control(struct parport *p,
						      unsigned char mask,
						      unsigned char val)
{
	const unsigned int wm =
		DCR_STROBE | DCR_AUTOFD | DCR_nINIT | DCR_SELECT;
	CHECK_EXTRA_BITS(p, mask, wm);
	CHECK_EXTRA_BITS(p, val, wm);
	__parport_ip32_frob_control(p, mask & wm, val & wm);
	return parport_ip32_read_control(p);
}

/**
 * parport_ip32_disable_irq - disable interrupts on the rising edge of nACK
 * @p:		pointer to &struct parport
 */
static inline void parport_ip32_disable_irq(struct parport *p)
{
	__parport_ip32_frob_control(p, DCR_IRQ, 0);
}

/**
 * parport_ip32_enable_irq - enable interrupts on the rising edge of nACK
 * @p:		pointer to &struct parport
 */
static inline void parport_ip32_enable_irq(struct parport *p)
{
	__parport_ip32_frob_control(p, DCR_IRQ, DCR_IRQ);
}

/**
 * parport_ip32_data_forward - enable host-to-peripheral communications
 * @p:		pointer to &struct parport
 *
 * Enable the data line drivers, for 8-bit host-to-peripheral communications.
 */
static inline void parport_ip32_data_forward(struct parport *p)
{
	__parport_ip32_frob_control(p, DCR_DIR, 0);
}

/**
 * parport_ip32_data_reverse - enable peripheral-to-host communications
 * @p:		pointer to &struct parport
 *
 * Place the data bus in a high impedance state, if @p->modes has the
 * PARPORT_MODE_TRISTATE bit set.
 */
static inline void parport_ip32_data_reverse(struct parport *p)
{
	__parport_ip32_frob_control(p, DCR_DIR, DCR_DIR);
}

/**
 * parport_ip32_init_state - for core parport code
 * @dev:	pointer to &struct pardevice
 * @s:		pointer to &struct parport_state to initialize
 */
static void parport_ip32_init_state(struct pardevice *dev,
				    struct parport_state *s)
{
	s->u.ip32.dcr = DCR_SELECT | DCR_nINIT;
	s->u.ip32.ecr = ECR_MODE_PS2 | ECR_nERRINTR | ECR_SERVINTR;
}

/**
 * parport_ip32_save_state - for core parport code
 * @p:		pointer to &struct parport
 * @s:		pointer to &struct parport_state to save state to
 */
static void parport_ip32_save_state(struct parport *p,
				    struct parport_state *s)
{
	s->u.ip32.dcr = __parport_ip32_read_control(p);
	s->u.ip32.ecr = parport_ip32_read_econtrol(p);
}

/**
 * parport_ip32_restore_state - for core parport code
 * @p:		pointer to &struct parport
 * @s:		pointer to &struct parport_state to restore state from
 */
static void parport_ip32_restore_state(struct parport *p,
				       struct parport_state *s)
{
	parport_ip32_set_mode(p, s->u.ip32.ecr & ECR_MODE_MASK);
	parport_ip32_write_econtrol(p, s->u.ip32.ecr);
	__parport_ip32_write_control(p, s->u.ip32.dcr);
}

/*--- EPP mode functions -----------------------------------------------*/

/**
 * parport_ip32_clear_epp_timeout - clear Timeout bit in EPP mode
 * @p:		pointer to &struct parport
 *
 * Returns 1 if the Timeout bit is clear, and 0 otherwise.
 */
static unsigned int parport_ip32_clear_epp_timeout(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	unsigned int cleared;

	if (!(parport_ip32_read_status(p) & DSR_TIMEOUT))
		cleared = 1;
	else {
		unsigned int r;
		/* To clear timeout some chips require double read */
		parport_ip32_read_status(p);
		r = parport_ip32_read_status(p);
		/* Some reset by writing 1 */
		writeb(r | DSR_TIMEOUT, priv->regs.dsr);
		/* Others by writing 0 */
		writeb(r & ~DSR_TIMEOUT, priv->regs.dsr);

		r = parport_ip32_read_status(p);
		cleared = !(r & DSR_TIMEOUT);
	}

	pr_trace(p, "(): %s", cleared ? "cleared" : "failed");
	return cleared;
}

/**
 * parport_ip32_epp_read - generic EPP read function
 * @eppreg:	I/O register to read from
 * @p:		pointer to &struct parport
 * @buf:	buffer to store read data
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_read(void __iomem *eppreg,
				    struct parport *p, void *buf,
				    size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	size_t got;
	parport_ip32_set_mode(p, ECR_MODE_EPP);
	parport_ip32_data_reverse(p);
	parport_ip32_write_control(p, DCR_nINIT);
	if ((flags & PARPORT_EPP_FAST) && (len > 1)) {
		readsb(eppreg, buf, len);
		if (readb(priv->regs.dsr) & DSR_TIMEOUT) {
			parport_ip32_clear_epp_timeout(p);
			return -EIO;
		}
		got = len;
	} else {
		u8 *bufp = buf;
		for (got = 0; got < len; got++) {
			*bufp++ = readb(eppreg);
			if (readb(priv->regs.dsr) & DSR_TIMEOUT) {
				parport_ip32_clear_epp_timeout(p);
				break;
			}
		}
	}
	parport_ip32_data_forward(p);
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	return got;
}

/**
 * parport_ip32_epp_write - generic EPP write function
 * @eppreg:	I/O register to write to
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_write(void __iomem *eppreg,
				     struct parport *p, const void *buf,
				     size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	size_t written;
	parport_ip32_set_mode(p, ECR_MODE_EPP);
	parport_ip32_data_forward(p);
	parport_ip32_write_control(p, DCR_nINIT);
	if ((flags & PARPORT_EPP_FAST) && (len > 1)) {
		writesb(eppreg, buf, len);
		if (readb(priv->regs.dsr) & DSR_TIMEOUT) {
			parport_ip32_clear_epp_timeout(p);
			return -EIO;
		}
		written = len;
	} else {
		const u8 *bufp = buf;
		for (written = 0; written < len; written++) {
			writeb(*bufp++, eppreg);
			if (readb(priv->regs.dsr) & DSR_TIMEOUT) {
				parport_ip32_clear_epp_timeout(p);
				break;
			}
		}
	}
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	return written;
}

/**
 * parport_ip32_epp_read_data - read a block of data in EPP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer to store read data
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_read_data(struct parport *p, void *buf,
					 size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return parport_ip32_epp_read(priv->regs.eppData0, p, buf, len, flags);
}

/**
 * parport_ip32_epp_write_data - write a block of data in EPP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_write_data(struct parport *p, const void *buf,
					  size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return parport_ip32_epp_write(priv->regs.eppData0, p, buf, len, flags);
}

/**
 * parport_ip32_epp_read_addr - read a block of addresses in EPP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer to store read data
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_read_addr(struct parport *p, void *buf,
					 size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return parport_ip32_epp_read(priv->regs.eppAddr, p, buf, len, flags);
}

/**
 * parport_ip32_epp_write_addr - write a block of addresses in EPP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 * @flags:	may be PARPORT_EPP_FAST
 */
static size_t parport_ip32_epp_write_addr(struct parport *p, const void *buf,
					  size_t len, int flags)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	return parport_ip32_epp_write(priv->regs.eppAddr, p, buf, len, flags);
}

/*--- ECP mode functions (FIFO) ----------------------------------------*/

/**
 * parport_ip32_fifo_wait_break - check if the waiting function should return
 * @p:		pointer to &struct parport
 * @expire:	timeout expiring date, in jiffies
 *
 * parport_ip32_fifo_wait_break() checks if the waiting function should return
 * immediately or not.  The break conditions are:
 *	- expired timeout;
 *	- a pending signal;
 *	- nFault asserted low.
 * This function also calls cond_resched().
 */
static unsigned int parport_ip32_fifo_wait_break(struct parport *p,
						 unsigned long expire)
{
	cond_resched();
	if (time_after(jiffies, expire)) {
		pr_debug1(PPIP32 "%s: FIFO write timed out\n", p->name);
		return 1;
	}
	if (signal_pending(current)) {
		pr_debug1(PPIP32 "%s: Signal pending\n", p->name);
		return 1;
	}
	if (!(parport_ip32_read_status(p) & DSR_nFAULT)) {
		pr_debug1(PPIP32 "%s: nFault asserted low\n", p->name);
		return 1;
	}
	return 0;
}

/**
 * parport_ip32_fwp_wait_polling - wait for FIFO to empty (polling)
 * @p:		pointer to &struct parport
 *
 * Returns the number of bytes that can safely be written in the FIFO.  A
 * return value of zero means that the calling function should terminate as
 * fast as possible.
 */
static unsigned int parport_ip32_fwp_wait_polling(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport * const physport = p->physport;
	unsigned long expire;
	unsigned int count;
	unsigned int ecr;

	expire = jiffies + physport->cad->timeout;
	count = 0;
	while (1) {
		if (parport_ip32_fifo_wait_break(p, expire))
			break;

		/* Check FIFO state.  We do nothing when the FIFO is nor full,
		 * nor empty.  It appears that the FIFO full bit is not always
		 * reliable, the FIFO state is sometimes wrongly reported, and
		 * the chip gets confused if we give it another byte. */
		ecr = parport_ip32_read_econtrol(p);
		if (ecr & ECR_F_EMPTY) {
			/* FIFO is empty, fill it up */
			count = priv->fifo_depth;
			break;
		}

		/* Wait a moment... */
		udelay(FIFO_POLLING_INTERVAL);
	} /* while (1) */

	return count;
}

/**
 * parport_ip32_fwp_wait_interrupt - wait for FIFO to empty (interrupt-driven)
 * @p:		pointer to &struct parport
 *
 * Returns the number of bytes that can safely be written in the FIFO.  A
 * return value of zero means that the calling function should terminate as
 * fast as possible.
 */
static unsigned int parport_ip32_fwp_wait_interrupt(struct parport *p)
{
	static unsigned int lost_interrupt = 0;
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport * const physport = p->physport;
	unsigned long nfault_timeout;
	unsigned long expire;
	unsigned int count;
	unsigned int ecr;

	nfault_timeout = min((unsigned long)physport->cad->timeout,
			     msecs_to_jiffies(FIFO_NFAULT_TIMEOUT));
	expire = jiffies + physport->cad->timeout;
	count = 0;
	while (1) {
		if (parport_ip32_fifo_wait_break(p, expire))
			break;

		/* Initialize mutex used to take interrupts into account */
		reinit_completion(&priv->irq_complete);

		/* Enable serviceIntr */
		parport_ip32_frob_econtrol(p, ECR_SERVINTR, 0);

		/* Enabling serviceIntr while the FIFO is empty does not
		 * always generate an interrupt, so check for emptiness
		 * now. */
		ecr = parport_ip32_read_econtrol(p);
		if (!(ecr & ECR_F_EMPTY)) {
			/* FIFO is not empty: wait for an interrupt or a
			 * timeout to occur */
			wait_for_completion_interruptible_timeout(
				&priv->irq_complete, nfault_timeout);
			ecr = parport_ip32_read_econtrol(p);
			if ((ecr & ECR_F_EMPTY) && !(ecr & ECR_SERVINTR)
			    && !lost_interrupt) {
				pr_warn(PPIP32 "%s: lost interrupt in %s\n",
					p->name, __func__);
				lost_interrupt = 1;
			}
		}

		/* Disable serviceIntr */
		parport_ip32_frob_econtrol(p, ECR_SERVINTR, ECR_SERVINTR);

		/* Check FIFO state */
		if (ecr & ECR_F_EMPTY) {
			/* FIFO is empty, fill it up */
			count = priv->fifo_depth;
			break;
		} else if (ecr & ECR_SERVINTR) {
			/* FIFO is not empty, but we know that can safely push
			 * writeIntrThreshold bytes into it */
			count = priv->writeIntrThreshold;
			break;
		}
		/* FIFO is not empty, and we did not get any interrupt.
		 * Either it's time to check for nFault, or a signal is
		 * pending.  This is verified in
		 * parport_ip32_fifo_wait_break(), so we continue the loop. */
	} /* while (1) */

	return count;
}

/**
 * parport_ip32_fifo_write_block_pio - write a block of data (PIO mode)
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 *
 * Uses PIO to write the contents of the buffer @buf into the parallel port
 * FIFO.  Returns the number of bytes that were actually written.  It can work
 * with or without the help of interrupts.  The parallel port must be
 * correctly initialized before calling parport_ip32_fifo_write_block_pio().
 */
static size_t parport_ip32_fifo_write_block_pio(struct parport *p,
						const void *buf, size_t len)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	const u8 *bufp = buf;
	size_t left = len;

	priv->irq_mode = PARPORT_IP32_IRQ_HERE;

	while (left > 0) {
		unsigned int count;

		count = (p->irq == PARPORT_IRQ_NONE) ?
			parport_ip32_fwp_wait_polling(p) :
			parport_ip32_fwp_wait_interrupt(p);
		if (count == 0)
			break;	/* Transmission should be stopped */
		if (count > left)
			count = left;
		if (count == 1) {
			writeb(*bufp, priv->regs.fifo);
			bufp++, left--;
		} else {
			writesb(priv->regs.fifo, bufp, count);
			bufp += count, left -= count;
		}
	}

	priv->irq_mode = PARPORT_IP32_IRQ_FWD;

	return len - left;
}

/**
 * parport_ip32_fifo_write_block_dma - write a block of data (DMA mode)
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 *
 * Uses DMA to write the contents of the buffer @buf into the parallel port
 * FIFO.  Returns the number of bytes that were actually written.  The
 * parallel port must be correctly initialized before calling
 * parport_ip32_fifo_write_block_dma().
 */
static size_t parport_ip32_fifo_write_block_dma(struct parport *p,
						const void *buf, size_t len)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport * const physport = p->physport;
	unsigned long nfault_timeout;
	unsigned long expire;
	size_t written;
	unsigned int ecr;

	priv->irq_mode = PARPORT_IP32_IRQ_HERE;

	parport_ip32_dma_start(p, DMA_TO_DEVICE, (void *)buf, len);
	reinit_completion(&priv->irq_complete);
	parport_ip32_frob_econtrol(p, ECR_DMAEN | ECR_SERVINTR, ECR_DMAEN);

	nfault_timeout = min((unsigned long)physport->cad->timeout,
			     msecs_to_jiffies(FIFO_NFAULT_TIMEOUT));
	expire = jiffies + physport->cad->timeout;
	while (1) {
		if (parport_ip32_fifo_wait_break(p, expire))
			break;
		wait_for_completion_interruptible_timeout(&priv->irq_complete,
							  nfault_timeout);
		ecr = parport_ip32_read_econtrol(p);
		if (ecr & ECR_SERVINTR)
			break;	/* DMA transfer just finished */
	}
	parport_ip32_dma_stop(p);
	written = len - parport_ip32_dma_get_residue();

	priv->irq_mode = PARPORT_IP32_IRQ_FWD;

	return written;
}

/**
 * parport_ip32_fifo_write_block - write a block of data
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 *
 * Uses PIO or DMA to write the contents of the buffer @buf into the parallel
 * p FIFO.  Returns the number of bytes that were actually written.
 */
static size_t parport_ip32_fifo_write_block(struct parport *p,
					    const void *buf, size_t len)
{
	size_t written = 0;
	if (len)
		/* FIXME - Maybe some threshold value should be set for @len
		 * under which we revert to PIO mode? */
		written = (p->modes & PARPORT_MODE_DMA) ?
			parport_ip32_fifo_write_block_dma(p, buf, len) :
			parport_ip32_fifo_write_block_pio(p, buf, len);
	return written;
}

/**
 * parport_ip32_drain_fifo - wait for FIFO to empty
 * @p:		pointer to &struct parport
 * @timeout:	timeout, in jiffies
 *
 * This function waits for FIFO to empty.  It returns 1 when FIFO is empty, or
 * 0 if the timeout @timeout is reached before, or if a signal is pending.
 */
static unsigned int parport_ip32_drain_fifo(struct parport *p,
					    unsigned long timeout)
{
	unsigned long expire = jiffies + timeout;
	unsigned int polling_interval;
	unsigned int counter;

	/* Busy wait for approx. 200us */
	for (counter = 0; counter < 40; counter++) {
		if (parport_ip32_read_econtrol(p) & ECR_F_EMPTY)
			break;
		if (time_after(jiffies, expire))
			break;
		if (signal_pending(current))
			break;
		udelay(5);
	}
	/* Poll slowly.  Polling interval starts with 1 millisecond, and is
	 * increased exponentially until 128.  */
	polling_interval = 1; /* msecs */
	while (!(parport_ip32_read_econtrol(p) & ECR_F_EMPTY)) {
		if (time_after_eq(jiffies, expire))
			break;
		msleep_interruptible(polling_interval);
		if (signal_pending(current))
			break;
		if (polling_interval < 128)
			polling_interval *= 2;
	}

	return !!(parport_ip32_read_econtrol(p) & ECR_F_EMPTY);
}

/**
 * parport_ip32_get_fifo_residue - reset FIFO
 * @p:		pointer to &struct parport
 * @mode:	current operation mode (ECR_MODE_PPF or ECR_MODE_ECP)
 *
 * This function resets FIFO, and returns the number of bytes remaining in it.
 */
static unsigned int parport_ip32_get_fifo_residue(struct parport *p,
						  unsigned int mode)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	unsigned int residue;
	unsigned int cnfga;

	/* FIXME - We are missing one byte if the printer is off-line.  I
	 * don't know how to detect this.  It looks that the full bit is not
	 * always reliable.  For the moment, the problem is avoided in most
	 * cases by testing for BUSY in parport_ip32_compat_write_data().
	 */
	if (parport_ip32_read_econtrol(p) & ECR_F_EMPTY)
		residue = 0;
	else {
		pr_debug1(PPIP32 "%s: FIFO is stuck\n", p->name);

		/* Stop all transfers.
		 *
		 * Microsoft's document instructs to drive DCR_STROBE to 0,
		 * but it doesn't work (at least in Compatibility mode, not
		 * tested in ECP mode).  Switching directly to Test mode (as
		 * in parport_pc) is not an option: it does confuse the port,
		 * ECP service interrupts are no more working after that.  A
		 * hard reset is then needed to revert to a sane state.
		 *
		 * Let's hope that the FIFO is really stuck and that the
		 * peripheral doesn't wake up now.
		 */
		parport_ip32_frob_control(p, DCR_STROBE, 0);

		/* Fill up FIFO */
		for (residue = priv->fifo_depth; residue > 0; residue--) {
			if (parport_ip32_read_econtrol(p) & ECR_F_FULL)
				break;
			writeb(0x00, priv->regs.fifo);
		}
	}
	if (residue)
		pr_debug1(PPIP32 "%s: %d PWord%s left in FIFO\n",
			  p->name, residue,
			  (residue == 1) ? " was" : "s were");

	/* Now reset the FIFO */
	parport_ip32_set_mode(p, ECR_MODE_PS2);

	/* Host recovery for ECP mode */
	if (mode == ECR_MODE_ECP) {
		parport_ip32_data_reverse(p);
		parport_ip32_frob_control(p, DCR_nINIT, 0);
		if (parport_wait_peripheral(p, DSR_PERROR, 0))
			pr_debug1(PPIP32 "%s: PEerror timeout 1 in %s\n",
				  p->name, __func__);
		parport_ip32_frob_control(p, DCR_STROBE, DCR_STROBE);
		parport_ip32_frob_control(p, DCR_nINIT, DCR_nINIT);
		if (parport_wait_peripheral(p, DSR_PERROR, DSR_PERROR))
			pr_debug1(PPIP32 "%s: PEerror timeout 2 in %s\n",
				  p->name, __func__);
	}

	/* Adjust residue if needed */
	parport_ip32_set_mode(p, ECR_MODE_CFG);
	cnfga = readb(priv->regs.cnfgA);
	if (!(cnfga & CNFGA_nBYTEINTRANS)) {
		pr_debug1(PPIP32 "%s: cnfgA contains 0x%02x\n",
			  p->name, cnfga);
		pr_debug1(PPIP32 "%s: Accounting for extra byte\n",
			  p->name);
		residue++;
	}

	/* Don't care about partial PWords since we do not support
	 * PWord != 1 byte. */

	/* Back to forward PS2 mode. */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	parport_ip32_data_forward(p);

	return residue;
}

/**
 * parport_ip32_compat_write_data - write a block of data in SPP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 * @flags:	ignored
 */
static size_t parport_ip32_compat_write_data(struct parport *p,
					     const void *buf, size_t len,
					     int flags)
{
	static unsigned int ready_before = 1;
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport * const physport = p->physport;
	size_t written = 0;

	/* Special case: a timeout of zero means we cannot call schedule().
	 * Also if O_NONBLOCK is set then use the default implementation. */
	if (physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
		return parport_ieee1284_write_compat(p, buf, len, flags);

	/* Reset FIFO, go in forward mode, and disable ackIntEn */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	parport_ip32_write_control(p, DCR_SELECT | DCR_nINIT);
	parport_ip32_data_forward(p);
	parport_ip32_disable_irq(p);
	parport_ip32_set_mode(p, ECR_MODE_PPF);
	physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;

	/* Wait for peripheral to become ready */
	if (parport_wait_peripheral(p, DSR_nBUSY | DSR_nFAULT,
				       DSR_nBUSY | DSR_nFAULT)) {
		/* Avoid to flood the logs */
		if (ready_before)
			pr_info(PPIP32 "%s: not ready in %s\n",
				p->name, __func__);
		ready_before = 0;
		goto stop;
	}
	ready_before = 1;

	written = parport_ip32_fifo_write_block(p, buf, len);

	/* Wait FIFO to empty.  Timeout is proportional to FIFO_depth.  */
	parport_ip32_drain_fifo(p, physport->cad->timeout * priv->fifo_depth);

	/* Check for a potential residue */
	written -= parport_ip32_get_fifo_residue(p, ECR_MODE_PPF);

	/* Then, wait for BUSY to get low. */
	if (parport_wait_peripheral(p, DSR_nBUSY, DSR_nBUSY))
		printk(KERN_DEBUG PPIP32 "%s: BUSY timeout in %s\n",
		       p->name, __func__);

stop:
	/* Reset FIFO */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;

	return written;
}

/*
 * FIXME - Insert here parport_ip32_ecp_read_data().
 */

/**
 * parport_ip32_ecp_write_data - write a block of data in ECP mode
 * @p:		pointer to &struct parport
 * @buf:	buffer of data to write
 * @len:	length of buffer @buf
 * @flags:	ignored
 */
static size_t parport_ip32_ecp_write_data(struct parport *p,
					  const void *buf, size_t len,
					  int flags)
{
	static unsigned int ready_before = 1;
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport * const physport = p->physport;
	size_t written = 0;

	/* Special case: a timeout of zero means we cannot call schedule().
	 * Also if O_NONBLOCK is set then use the default implementation. */
	if (physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
		return parport_ieee1284_ecp_write_data(p, buf, len, flags);

	/* Negotiate to forward mode if necessary. */
	if (physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
		/* Event 47: Set nInit high. */
		parport_ip32_frob_control(p, DCR_nINIT | DCR_AUTOFD,
					     DCR_nINIT | DCR_AUTOFD);

		/* Event 49: PError goes high. */
		if (parport_wait_peripheral(p, DSR_PERROR, DSR_PERROR)) {
			printk(KERN_DEBUG PPIP32 "%s: PError timeout in %s\n",
			       p->name, __func__);
			physport->ieee1284.phase = IEEE1284_PH_ECP_DIR_UNKNOWN;
			return 0;
		}
	}

	/* Reset FIFO, go in forward mode, and disable ackIntEn */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	parport_ip32_write_control(p, DCR_SELECT | DCR_nINIT);
	parport_ip32_data_forward(p);
	parport_ip32_disable_irq(p);
	parport_ip32_set_mode(p, ECR_MODE_ECP);
	physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;

	/* Wait for peripheral to become ready */
	if (parport_wait_peripheral(p, DSR_nBUSY | DSR_nFAULT,
				       DSR_nBUSY | DSR_nFAULT)) {
		/* Avoid to flood the logs */
		if (ready_before)
			pr_info(PPIP32 "%s: not ready in %s\n",
				p->name, __func__);
		ready_before = 0;
		goto stop;
	}
	ready_before = 1;

	written = parport_ip32_fifo_write_block(p, buf, len);

	/* Wait FIFO to empty.  Timeout is proportional to FIFO_depth.  */
	parport_ip32_drain_fifo(p, physport->cad->timeout * priv->fifo_depth);

	/* Check for a potential residue */
	written -= parport_ip32_get_fifo_residue(p, ECR_MODE_ECP);

	/* Then, wait for BUSY to get low. */
	if (parport_wait_peripheral(p, DSR_nBUSY, DSR_nBUSY))
		printk(KERN_DEBUG PPIP32 "%s: BUSY timeout in %s\n",
		       p->name, __func__);

stop:
	/* Reset FIFO */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;

	return written;
}

/*
 * FIXME - Insert here parport_ip32_ecp_write_addr().
 */

/*--- Default parport operations ---------------------------------------*/

static const struct parport_operations parport_ip32_ops __initconst = {
	.write_data		= parport_ip32_write_data,
	.read_data		= parport_ip32_read_data,

	.write_control		= parport_ip32_write_control,
	.read_control		= parport_ip32_read_control,
	.frob_control		= parport_ip32_frob_control,

	.read_status		= parport_ip32_read_status,

	.enable_irq		= parport_ip32_enable_irq,
	.disable_irq		= parport_ip32_disable_irq,

	.data_forward		= parport_ip32_data_forward,
	.data_reverse		= parport_ip32_data_reverse,

	.init_state		= parport_ip32_init_state,
	.save_state		= parport_ip32_save_state,
	.restore_state		= parport_ip32_restore_state,

	.epp_write_data		= parport_ieee1284_epp_write_data,
	.epp_read_data		= parport_ieee1284_epp_read_data,
	.epp_write_addr		= parport_ieee1284_epp_write_addr,
	.epp_read_addr		= parport_ieee1284_epp_read_addr,

	.ecp_write_data		= parport_ieee1284_ecp_write_data,
	.ecp_read_data		= parport_ieee1284_ecp_read_data,
	.ecp_write_addr		= parport_ieee1284_ecp_write_addr,

	.compat_write_data	= parport_ieee1284_write_compat,
	.nibble_read_data	= parport_ieee1284_read_nibble,
	.byte_read_data		= parport_ieee1284_read_byte,

	.owner			= THIS_MODULE,
};

/*--- Device detection -------------------------------------------------*/

/**
 * parport_ip32_ecp_supported - check for an ECP port
 * @p:		pointer to the &parport structure
 *
 * Returns 1 if an ECP port is found, and 0 otherwise.  This function actually
 * checks if an Extended Control Register seems to be present.  On successful
 * return, the port is placed in SPP mode.
 */
static __init unsigned int parport_ip32_ecp_supported(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	unsigned int ecr;

	ecr = ECR_MODE_PS2 | ECR_nERRINTR | ECR_SERVINTR;
	writeb(ecr, priv->regs.ecr);
	if (readb(priv->regs.ecr) != (ecr | ECR_F_EMPTY))
		goto fail;

	pr_probe(p, "Found working ECR register\n");
	parport_ip32_set_mode(p, ECR_MODE_SPP);
	parport_ip32_write_control(p, DCR_SELECT | DCR_nINIT);
	return 1;

fail:
	pr_probe(p, "ECR register not found\n");
	return 0;
}

/**
 * parport_ip32_fifo_supported - check for FIFO parameters
 * @p:		pointer to the &parport structure
 *
 * Check for FIFO parameters of an Extended Capabilities Port.  Returns 1 on
 * success, and 0 otherwise.  Adjust FIFO parameters in the parport structure.
 * On return, the port is placed in SPP mode.
 */
static __init unsigned int parport_ip32_fifo_supported(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	unsigned int configa, configb;
	unsigned int pword;
	unsigned int i;

	/* Configuration mode */
	parport_ip32_set_mode(p, ECR_MODE_CFG);
	configa = readb(priv->regs.cnfgA);
	configb = readb(priv->regs.cnfgB);

	/* Find out PWord size */
	switch (configa & CNFGA_ID_MASK) {
	case CNFGA_ID_8:
		pword = 1;
		break;
	case CNFGA_ID_16:
		pword = 2;
		break;
	case CNFGA_ID_32:
		pword = 4;
		break;
	default:
		pr_probe(p, "Unknown implementation ID: 0x%0x\n",
			 (configa & CNFGA_ID_MASK) >> CNFGA_ID_SHIFT);
		goto fail;
		break;
	}
	if (pword != 1) {
		pr_probe(p, "Unsupported PWord size: %u\n", pword);
		goto fail;
	}
	priv->pword = pword;
	pr_probe(p, "PWord is %u bits\n", 8 * priv->pword);

	/* Check for compression support */
	writeb(configb | CNFGB_COMPRESS, priv->regs.cnfgB);
	if (readb(priv->regs.cnfgB) & CNFGB_COMPRESS)
		pr_probe(p, "Hardware compression detected (unsupported)\n");
	writeb(configb & ~CNFGB_COMPRESS, priv->regs.cnfgB);

	/* Reset FIFO and go in test mode (no interrupt, no DMA) */
	parport_ip32_set_mode(p, ECR_MODE_TST);

	/* FIFO must be empty now */
	if (!(readb(priv->regs.ecr) & ECR_F_EMPTY)) {
		pr_probe(p, "FIFO not reset\n");
		goto fail;
	}

	/* Find out FIFO depth. */
	priv->fifo_depth = 0;
	for (i = 0; i < 1024; i++) {
		if (readb(priv->regs.ecr) & ECR_F_FULL) {
			/* FIFO full */
			priv->fifo_depth = i;
			break;
		}
		writeb((u8)i, priv->regs.fifo);
	}
	if (i >= 1024) {
		pr_probe(p, "Can't fill FIFO\n");
		goto fail;
	}
	if (!priv->fifo_depth) {
		pr_probe(p, "Can't get FIFO depth\n");
		goto fail;
	}
	pr_probe(p, "FIFO is %u PWords deep\n", priv->fifo_depth);

	/* Enable interrupts */
	parport_ip32_frob_econtrol(p, ECR_SERVINTR, 0);

	/* Find out writeIntrThreshold: number of PWords we know we can write
	 * if we get an interrupt. */
	priv->writeIntrThreshold = 0;
	for (i = 0; i < priv->fifo_depth; i++) {
		if (readb(priv->regs.fifo) != (u8)i) {
			pr_probe(p, "Invalid data in FIFO\n");
			goto fail;
		}
		if (!priv->writeIntrThreshold
		    && readb(priv->regs.ecr) & ECR_SERVINTR)
			/* writeIntrThreshold reached */
			priv->writeIntrThreshold = i + 1;
		if (i + 1 < priv->fifo_depth
		    && readb(priv->regs.ecr) & ECR_F_EMPTY) {
			/* FIFO empty before the last byte? */
			pr_probe(p, "Data lost in FIFO\n");
			goto fail;
		}
	}
	if (!priv->writeIntrThreshold) {
		pr_probe(p, "Can't get writeIntrThreshold\n");
		goto fail;
	}
	pr_probe(p, "writeIntrThreshold is %u\n", priv->writeIntrThreshold);

	/* FIFO must be empty now */
	if (!(readb(priv->regs.ecr) & ECR_F_EMPTY)) {
		pr_probe(p, "Can't empty FIFO\n");
		goto fail;
	}

	/* Reset FIFO */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	/* Set reverse direction (must be in PS2 mode) */
	parport_ip32_data_reverse(p);
	/* Test FIFO, no interrupt, no DMA */
	parport_ip32_set_mode(p, ECR_MODE_TST);
	/* Enable interrupts */
	parport_ip32_frob_econtrol(p, ECR_SERVINTR, 0);

	/* Find out readIntrThreshold: number of PWords we can read if we get
	 * an interrupt. */
	priv->readIntrThreshold = 0;
	for (i = 0; i < priv->fifo_depth; i++) {
		writeb(0xaa, priv->regs.fifo);
		if (readb(priv->regs.ecr) & ECR_SERVINTR) {
			/* readIntrThreshold reached */
			priv->readIntrThreshold = i + 1;
			break;
		}
	}
	if (!priv->readIntrThreshold) {
		pr_probe(p, "Can't get readIntrThreshold\n");
		goto fail;
	}
	pr_probe(p, "readIntrThreshold is %u\n", priv->readIntrThreshold);

	/* Reset ECR */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	parport_ip32_data_forward(p);
	parport_ip32_set_mode(p, ECR_MODE_SPP);
	return 1;

fail:
	priv->fifo_depth = 0;
	parport_ip32_set_mode(p, ECR_MODE_SPP);
	return 0;
}

/*--- Initialization code ----------------------------------------------*/

/**
 * parport_ip32_make_isa_registers - compute (ISA) register addresses
 * @regs:	pointer to &struct parport_ip32_regs to fill
 * @base:	base address of standard and EPP registers
 * @base_hi:	base address of ECP registers
 * @regshift:	how much to shift register offset by
 *
 * Compute register addresses, according to the ISA standard.  The addresses
 * of the standard and EPP registers are computed from address @base.  The
 * addresses of the ECP registers are computed from address @base_hi.
 */
static void __init
parport_ip32_make_isa_registers(struct parport_ip32_regs *regs,
				void __iomem *base, void __iomem *base_hi,
				unsigned int regshift)
{
#define r_base(offset)    ((u8 __iomem *)base    + ((offset) << regshift))
#define r_base_hi(offset) ((u8 __iomem *)base_hi + ((offset) << regshift))
	*regs = (struct parport_ip32_regs){
		.data		= r_base(0),
		.dsr		= r_base(1),
		.dcr		= r_base(2),
		.eppAddr	= r_base(3),
		.eppData0	= r_base(4),
		.eppData1	= r_base(5),
		.eppData2	= r_base(6),
		.eppData3	= r_base(7),
		.ecpAFifo	= r_base(0),
		.fifo		= r_base_hi(0),
		.cnfgA		= r_base_hi(0),
		.cnfgB		= r_base_hi(1),
		.ecr		= r_base_hi(2)
	};
#undef r_base_hi
#undef r_base
}

/**
 * parport_ip32_probe_port - probe and register IP32 built-in parallel port
 *
 * Returns the new allocated &parport structure.  On error, an error code is
 * encoded in return value with the ERR_PTR function.
 */
static __init struct parport *parport_ip32_probe_port(void)
{
	struct parport_ip32_regs regs;
	struct parport_ip32_private *priv = NULL;
	struct parport_operations *ops = NULL;
	struct parport *p = NULL;
	int err;

	parport_ip32_make_isa_registers(&regs, &mace->isa.parallel,
					&mace->isa.ecp1284, 8 /* regshift */);

	ops = kmalloc(sizeof(struct parport_operations), GFP_KERNEL);
	priv = kmalloc(sizeof(struct parport_ip32_private), GFP_KERNEL);
	p = parport_register_port(0, PARPORT_IRQ_NONE, PARPORT_DMA_NONE, ops);
	if (ops == NULL || priv == NULL || p == NULL) {
		err = -ENOMEM;
		goto fail;
	}
	p->base = MACE_BASE + offsetof(struct sgi_mace, isa.parallel);
	p->base_hi = MACE_BASE + offsetof(struct sgi_mace, isa.ecp1284);
	p->private_data = priv;

	*ops = parport_ip32_ops;
	*priv = (struct parport_ip32_private){
		.regs			= regs,
		.dcr_writable		= DCR_DIR | DCR_SELECT | DCR_nINIT |
					  DCR_AUTOFD | DCR_STROBE,
		.irq_mode		= PARPORT_IP32_IRQ_FWD,
	};
	init_completion(&priv->irq_complete);

	/* Probe port. */
	if (!parport_ip32_ecp_supported(p)) {
		err = -ENODEV;
		goto fail;
	}
	parport_ip32_dump_state(p, "begin init", 0);

	/* We found what looks like a working ECR register.  Simply assume
	 * that all modes are correctly supported.  Enable basic modes. */
	p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
	p->modes |= PARPORT_MODE_TRISTATE;

	if (!parport_ip32_fifo_supported(p)) {
		pr_warn(PPIP32 "%s: error: FIFO disabled\n", p->name);
		/* Disable hardware modes depending on a working FIFO. */
		features &= ~PARPORT_IP32_ENABLE_SPP;
		features &= ~PARPORT_IP32_ENABLE_ECP;
		/* DMA is not needed if FIFO is not supported.  */
		features &= ~PARPORT_IP32_ENABLE_DMA;
	}

	/* Request IRQ */
	if (features & PARPORT_IP32_ENABLE_IRQ) {
		int irq = MACEISA_PARALLEL_IRQ;
		if (request_irq(irq, parport_ip32_interrupt, 0, p->name, p)) {
			pr_warn(PPIP32 "%s: error: IRQ disabled\n", p->name);
			/* DMA cannot work without interrupts. */
			features &= ~PARPORT_IP32_ENABLE_DMA;
		} else {
			pr_probe(p, "Interrupt support enabled\n");
			p->irq = irq;
			priv->dcr_writable |= DCR_IRQ;
		}
	}

	/* Allocate DMA resources */
	if (features & PARPORT_IP32_ENABLE_DMA) {
		if (parport_ip32_dma_register())
			pr_warn(PPIP32 "%s: error: DMA disabled\n", p->name);
		else {
			pr_probe(p, "DMA support enabled\n");
			p->dma = 0; /* arbitrary value != PARPORT_DMA_NONE */
			p->modes |= PARPORT_MODE_DMA;
		}
	}

	if (features & PARPORT_IP32_ENABLE_SPP) {
		/* Enable compatibility FIFO mode */
		p->ops->compat_write_data = parport_ip32_compat_write_data;
		p->modes |= PARPORT_MODE_COMPAT;
		pr_probe(p, "Hardware support for SPP mode enabled\n");
	}
	if (features & PARPORT_IP32_ENABLE_EPP) {
		/* Set up access functions to use EPP hardware. */
		p->ops->epp_read_data = parport_ip32_epp_read_data;
		p->ops->epp_write_data = parport_ip32_epp_write_data;
		p->ops->epp_read_addr = parport_ip32_epp_read_addr;
		p->ops->epp_write_addr = parport_ip32_epp_write_addr;
		p->modes |= PARPORT_MODE_EPP;
		pr_probe(p, "Hardware support for EPP mode enabled\n");
	}
	if (features & PARPORT_IP32_ENABLE_ECP) {
		/* Enable ECP FIFO mode */
		p->ops->ecp_write_data = parport_ip32_ecp_write_data;
		/* FIXME - not implemented */
/*		p->ops->ecp_read_data  = parport_ip32_ecp_read_data; */
/*		p->ops->ecp_write_addr = parport_ip32_ecp_write_addr; */
		p->modes |= PARPORT_MODE_ECP;
		pr_probe(p, "Hardware support for ECP mode enabled\n");
	}

	/* Initialize the port with sensible values */
	parport_ip32_set_mode(p, ECR_MODE_PS2);
	parport_ip32_write_control(p, DCR_SELECT | DCR_nINIT);
	parport_ip32_data_forward(p);
	parport_ip32_disable_irq(p);
	parport_ip32_write_data(p, 0x00);
	parport_ip32_dump_state(p, "end init", 0);

	/* Print out what we found */
	pr_info("%s: SGI IP32 at 0x%lx (0x%lx)", p->name, p->base, p->base_hi);
	if (p->irq != PARPORT_IRQ_NONE)
		pr_cont(", irq %d", p->irq);
	pr_cont(" [");
#define printmode(x)							\
do {									\
	if (p->modes & PARPORT_MODE_##x)				\
		pr_cont("%s%s", f++ ? "," : "", #x);			\
} while (0)
	{
		unsigned int f = 0;
		printmode(PCSPP);
		printmode(TRISTATE);
		printmode(COMPAT);
		printmode(EPP);
		printmode(ECP);
		printmode(DMA);
	}
#undef printmode
	pr_cont("]\n");

	parport_announce_port(p);
	return p;

fail:
	if (p)
		parport_put_port(p);
	kfree(priv);
	kfree(ops);
	return ERR_PTR(err);
}

/**
 * parport_ip32_unregister_port - unregister a parallel port
 * @p:		pointer to the &struct parport
 *
 * Unregisters a parallel port and free previously allocated resources
 * (memory, IRQ, ...).
 */
static __exit void parport_ip32_unregister_port(struct parport *p)
{
	struct parport_ip32_private * const priv = p->physport->private_data;
	struct parport_operations *ops = p->ops;

	parport_remove_port(p);
	if (p->modes & PARPORT_MODE_DMA)
		parport_ip32_dma_unregister();
	if (p->irq != PARPORT_IRQ_NONE)
		free_irq(p->irq, p);
	parport_put_port(p);
	kfree(priv);
	kfree(ops);
}

/**
 * parport_ip32_init - module initialization function
 */
static int __init parport_ip32_init(void)
{
	pr_info(PPIP32 "SGI IP32 built-in parallel port driver v0.6\n");
	this_port = parport_ip32_probe_port();
	return PTR_ERR_OR_ZERO(this_port);
}

/**
 * parport_ip32_exit - module termination function
 */
static void __exit parport_ip32_exit(void)
{
	parport_ip32_unregister_port(this_port);
}

/*--- Module stuff -----------------------------------------------------*/

MODULE_AUTHOR("Arnaud Giersch <arnaud.giersch@free.fr>");
MODULE_DESCRIPTION("SGI IP32 built-in parallel port driver");
MODULE_LICENSE("GPL");
MODULE_VERSION("0.6");		/* update in parport_ip32_init() too */

module_init(parport_ip32_init);
module_exit(parport_ip32_exit);

module_param(verbose_probing, bool, S_IRUGO);
MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialization");

module_param(features, uint, S_IRUGO);
MODULE_PARM_DESC(features,
		 "Bit mask of features to enable"
		 ", bit 0: IRQ support"
		 ", bit 1: DMA support"
		 ", bit 2: hardware SPP mode"
		 ", bit 3: hardware EPP mode"
		 ", bit 4: hardware ECP mode");