1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
/*---------------------------------------------------------------------------+
| fpu_system.h |
| |
| Copyright (C) 1992,1994,1997 |
| W. Metzenthen, 22 Parker St, Ormond, Vic 3163, |
| Australia. E-mail billm@suburbia.net |
| |
+---------------------------------------------------------------------------*/
#ifndef _FPU_SYSTEM_H
#define _FPU_SYSTEM_H
/* system dependent definitions */
#include <linux/sched.h>
#include <linux/kernel.h>
#include <linux/mm.h>
#include <asm/desc.h>
#include <asm/mmu_context.h>
static inline struct desc_struct FPU_get_ldt_descriptor(unsigned seg)
{
static struct desc_struct zero_desc;
struct desc_struct ret = zero_desc;
#ifdef CONFIG_MODIFY_LDT_SYSCALL
seg >>= 3;
mutex_lock(¤t->mm->context.lock);
if (current->mm->context.ldt && seg < current->mm->context.ldt->size)
ret = current->mm->context.ldt->entries[seg];
mutex_unlock(¤t->mm->context.lock);
#endif
return ret;
}
#define SEG_D_SIZE(x) ((x).b & (3 << 21))
#define SEG_G_BIT(x) ((x).b & (1 << 23))
#define SEG_GRANULARITY(x) (((x).b & (1 << 23)) ? 4096 : 1)
#define SEG_286_MODE(x) ((x).b & ( 0xff000000 | 0xf0000 | (1 << 23)))
#define SEG_BASE_ADDR(s) (((s).b & 0xff000000) \
| (((s).b & 0xff) << 16) | ((s).a >> 16))
#define SEG_LIMIT(s) (((s).b & 0xff0000) | ((s).a & 0xffff))
#define SEG_EXECUTE_ONLY(s) (((s).b & ((1 << 11) | (1 << 9))) == (1 << 11))
#define SEG_WRITE_PERM(s) (((s).b & ((1 << 11) | (1 << 9))) == (1 << 9))
#define SEG_EXPAND_DOWN(s) (((s).b & ((1 << 11) | (1 << 10))) \
== (1 << 10))
#define I387 (¤t->thread.fpu.state)
#define FPU_info (I387->soft.info)
#define FPU_CS (*(unsigned short *) &(FPU_info->regs->cs))
#define FPU_SS (*(unsigned short *) &(FPU_info->regs->ss))
#define FPU_DS (*(unsigned short *) &(FPU_info->regs->ds))
#define FPU_EAX (FPU_info->regs->ax)
#define FPU_EFLAGS (FPU_info->regs->flags)
#define FPU_EIP (FPU_info->regs->ip)
#define FPU_ORIG_EIP (FPU_info->___orig_eip)
#define FPU_lookahead (I387->soft.lookahead)
/* nz if ip_offset and cs_selector are not to be set for the current
instruction. */
#define no_ip_update (*(u_char *)&(I387->soft.no_update))
#define FPU_rm (*(u_char *)&(I387->soft.rm))
/* Number of bytes of data which can be legally accessed by the current
instruction. This only needs to hold a number <= 108, so a byte will do. */
#define access_limit (*(u_char *)&(I387->soft.alimit))
#define partial_status (I387->soft.swd)
#define control_word (I387->soft.cwd)
#define fpu_tag_word (I387->soft.twd)
#define registers (I387->soft.st_space)
#define top (I387->soft.ftop)
#define instruction_address (*(struct address *)&I387->soft.fip)
#define operand_address (*(struct address *)&I387->soft.foo)
#define FPU_access_ok(x,y,z) if ( !access_ok(x,y,z) ) \
math_abort(FPU_info,SIGSEGV)
#define FPU_abort math_abort(FPU_info, SIGSEGV)
#undef FPU_IGNORE_CODE_SEGV
#ifdef FPU_IGNORE_CODE_SEGV
/* access_ok() is very expensive, and causes the emulator to run
about 20% slower if applied to the code. Anyway, errors due to bad
code addresses should be much rarer than errors due to bad data
addresses. */
#define FPU_code_access_ok(z)
#else
/* A simpler test than access_ok() can probably be done for
FPU_code_access_ok() because the only possible error is to step
past the upper boundary of a legal code area. */
#define FPU_code_access_ok(z) FPU_access_ok(VERIFY_READ,(void __user *)FPU_EIP,z)
#endif
#define FPU_get_user(x,y) get_user((x),(y))
#define FPU_put_user(x,y) put_user((x),(y))
#endif
|
