1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
|
/*
* arch/arm/mach-lpc32xx/pm.c
*
* Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
* Modified by Kevin Wells <kevin.wells@nxp.com>
*
* 2005 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
/*
* LPC32XX CPU and system power management
*
* The LCP32XX has three CPU modes for controlling system power: run,
* direct-run, and halt modes. When switching between halt and run modes,
* the CPU transistions through direct-run mode. For Linux, direct-run
* mode is not used in normal operation. Halt mode is used when the
* system is fully suspended.
*
* Run mode:
* The ARM CPU clock (HCLK_PLL), HCLK bus clock, and PCLK bus clocks are
* derived from the HCLK PLL. The HCLK and PCLK bus rates are divided from
* the HCLK_PLL rate. Linux runs in this mode.
*
* Direct-run mode:
* The ARM CPU clock, HCLK bus clock, and PCLK bus clocks are driven from
* SYSCLK. SYSCLK is usually around 13MHz, but may vary based on SYSCLK
* source or the frequency of the main oscillator. In this mode, the
* HCLK_PLL can be safely enabled, changed, or disabled.
*
* Halt mode:
* SYSCLK is gated off and the CPU and system clocks are halted.
* Peripherals based on the 32KHz oscillator clock (ie, RTC, touch,
* key scanner, etc.) still operate if enabled. In this state, an enabled
* system event (ie, GPIO state change, RTC match, key press, etc.) will
* wake the system up back into direct-run mode.
*
* DRAM refresh
* DRAM clocking and refresh are slightly different for systems with DDR
* DRAM or regular SDRAM devices. If SDRAM is used in the system, the
* SDRAM will still be accessible in direct-run mode. In DDR based systems,
* a transistion to direct-run mode will stop all DDR accesses (no clocks).
* Because of this, the code to switch power modes and the code to enter
* and exit DRAM self-refresh modes must not be executed in DRAM. A small
* section of IRAM is used instead for this.
*
* Suspend is handled with the following logic:
* Backup a small area of IRAM used for the suspend code
* Copy suspend code to IRAM
* Transfer control to code in IRAM
* Places DRAMs in self-refresh mode
* Enter direct-run mode
* Save state of HCLK_PLL PLL
* Disable HCLK_PLL PLL
* Enter halt mode - CPU and buses will stop
* System enters direct-run mode when an enabled event occurs
* HCLK PLL state is restored
* Run mode is entered
* DRAMS are placed back into normal mode
* Code execution returns from IRAM
* IRAM code are used for suspend is restored
* Suspend mode is exited
*/
#include <linux/suspend.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <asm/cacheflush.h>
#include <mach/hardware.h>
#include <mach/platform.h>
#include "common.h"
#include "clock.h"
#define TEMP_IRAM_AREA IO_ADDRESS(LPC32XX_IRAM_BASE)
/*
* Both STANDBY and MEM suspend states are handled the same with no
* loss of CPU or memory state
*/
static int lpc32xx_pm_enter(suspend_state_t state)
{
int (*lpc32xx_suspend_ptr) (void);
void *iram_swap_area;
/* Allocate some space for temporary IRAM storage */
iram_swap_area = kmalloc(lpc32xx_sys_suspend_sz, GFP_KERNEL);
if (!iram_swap_area) {
printk(KERN_ERR
"PM Suspend: cannot allocate memory to save portion "
"of SRAM\n");
return -ENOMEM;
}
/* Backup a small area of IRAM used for the suspend code */
memcpy(iram_swap_area, (void *) TEMP_IRAM_AREA,
lpc32xx_sys_suspend_sz);
/*
* Copy code to suspend system into IRAM. The suspend code
* needs to run from IRAM as DRAM may no longer be available
* when the PLL is stopped.
*/
memcpy((void *) TEMP_IRAM_AREA, &lpc32xx_sys_suspend,
lpc32xx_sys_suspend_sz);
flush_icache_range((unsigned long)TEMP_IRAM_AREA,
(unsigned long)(TEMP_IRAM_AREA) + lpc32xx_sys_suspend_sz);
/* Transfer to suspend code in IRAM */
lpc32xx_suspend_ptr = (void *) TEMP_IRAM_AREA;
flush_cache_all();
(void) lpc32xx_suspend_ptr();
/* Restore original IRAM contents */
memcpy((void *) TEMP_IRAM_AREA, iram_swap_area,
lpc32xx_sys_suspend_sz);
kfree(iram_swap_area);
return 0;
}
static const struct platform_suspend_ops lpc32xx_pm_ops = {
.valid = suspend_valid_only_mem,
.enter = lpc32xx_pm_enter,
};
#define EMC_DYN_MEM_CTRL_OFS 0x20
#define EMC_SRMMC (1 << 3)
#define EMC_CTRL_REG io_p2v(LPC32XX_EMC_BASE + EMC_DYN_MEM_CTRL_OFS)
static int __init lpc32xx_pm_init(void)
{
/*
* Setup SDRAM self-refresh clock to automatically disable o
* start of self-refresh. This only needs to be done once.
*/
__raw_writel(__raw_readl(EMC_CTRL_REG) | EMC_SRMMC, EMC_CTRL_REG);
suspend_set_ops(&lpc32xx_pm_ops);
return 0;
}
arch_initcall(lpc32xx_pm_init);
|
