summaryrefslogtreecommitdiff
path: root/arch/arm/mach-ixp4xx/dsmg600-setup.c
blob: db488ecc98b54ea6f832bcba1b5e45d4edafd4f0 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
// SPDX-License-Identifier: GPL-2.0
/*
 * DSM-G600 board-setup
 *
 * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
 * Copyright (C) 2006 Tower Technologies
 *
 * based on ixdp425-setup.c:
 *      Copyright (C) 2003-2004 MontaVista Software, Inc.
 * based on nslu2-power.c:
 *	Copyright (C) 2005 Tower Technologies
 * based on nslu2-io.c:
 *	Copyright (C) 2004 Karen Spearel
 *
 * Author: Alessandro Zummo <a.zummo@towertech.it>
 * Author: Michael Westerhof <mwester@dls.net>
 * Author: Rod Whitby <rod@whitby.id.au>
 * Maintainers: http://www.nslu2-linux.org/
 */
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <linux/timer.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/leds.h>
#include <linux/reboot.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>

#include <mach/hardware.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>

#define DSMG600_SDA_PIN		5
#define DSMG600_SCL_PIN		4

/* DSM-G600 Timer Setting */
#define DSMG600_FREQ		66000000

/* Buttons */
#define DSMG600_PB_GPIO		15	/* power button */
#define DSMG600_RB_GPIO		3	/* reset button */

/* Power control */
#define DSMG600_PO_GPIO		2	/* power off */

/* LEDs */
#define DSMG600_LED_PWR_GPIO	0
#define DSMG600_LED_WLAN_GPIO	14

static struct flash_platform_data dsmg600_flash_data = {
	.map_name		= "cfi_probe",
	.width			= 2,
};

static struct resource dsmg600_flash_resource = {
	.flags			= IORESOURCE_MEM,
};

static struct platform_device dsmg600_flash = {
	.name			= "IXP4XX-Flash",
	.id			= 0,
	.dev.platform_data	= &dsmg600_flash_data,
	.num_resources		= 1,
	.resource		= &dsmg600_flash_resource,
};

static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
	.sda_pin		= DSMG600_SDA_PIN,
	.scl_pin		= DSMG600_SCL_PIN,
};

static struct platform_device dsmg600_i2c_gpio = {
	.name			= "i2c-gpio",
	.id			= 0,
	.dev	 = {
		.platform_data	= &dsmg600_i2c_gpio_data,
	},
};

static struct i2c_board_info __initdata dsmg600_i2c_board_info [] = {
	{
		I2C_BOARD_INFO("pcf8563", 0x51),
	},
};

static struct gpio_led dsmg600_led_pins[] = {
	{
		.name		= "dsmg600:green:power",
		.gpio		= DSMG600_LED_PWR_GPIO,
	},
	{
		.name		= "dsmg600:green:wlan",
		.gpio		= DSMG600_LED_WLAN_GPIO,
		.active_low	= true,
	},
};

static struct gpio_led_platform_data dsmg600_led_data = {
	.num_leds		= ARRAY_SIZE(dsmg600_led_pins),
	.leds			= dsmg600_led_pins,
};

static struct platform_device dsmg600_leds = {
	.name			= "leds-gpio",
	.id			= -1,
	.dev.platform_data	= &dsmg600_led_data,
};

static struct resource dsmg600_uart_resources[] = {
	{
		.start		= IXP4XX_UART1_BASE_PHYS,
		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
		.flags		= IORESOURCE_MEM,
	},
	{
		.start		= IXP4XX_UART2_BASE_PHYS,
		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
		.flags		= IORESOURCE_MEM,
	}
};

static struct plat_serial8250_port dsmg600_uart_data[] = {
	{
		.mapbase	= IXP4XX_UART1_BASE_PHYS,
		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
		.irq		= IRQ_IXP4XX_UART1,
		.flags		= UPF_BOOT_AUTOCONF,
		.iotype		= UPIO_MEM,
		.regshift	= 2,
		.uartclk	= IXP4XX_UART_XTAL,
	},
	{
		.mapbase	= IXP4XX_UART2_BASE_PHYS,
		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
		.irq		= IRQ_IXP4XX_UART2,
		.flags		= UPF_BOOT_AUTOCONF,
		.iotype		= UPIO_MEM,
		.regshift	= 2,
		.uartclk	= IXP4XX_UART_XTAL,
	},
	{ }
};

static struct platform_device dsmg600_uart = {
	.name			= "serial8250",
	.id			= PLAT8250_DEV_PLATFORM,
	.dev.platform_data	= dsmg600_uart_data,
	.num_resources		= ARRAY_SIZE(dsmg600_uart_resources),
	.resource		= dsmg600_uart_resources,
};

static struct platform_device *dsmg600_devices[] __initdata = {
	&dsmg600_i2c_gpio,
	&dsmg600_flash,
	&dsmg600_leds,
};

static void dsmg600_power_off(void)
{
	/* enable the pwr cntl and drive it high */
	gpio_direction_output(DSMG600_PO_GPIO, 1);
}

/* This is used to make sure the power-button pusher is serious.  The button
 * must be held until the value of this counter reaches zero.
 */
static int power_button_countdown;

/* Must hold the button down for at least this many counts to be processed */
#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */

static void dsmg600_power_handler(unsigned long data);
static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);

static void dsmg600_power_handler(unsigned long data)
{
	/* This routine is called twice per second to check the
	 * state of the power button.
	 */

	if (gpio_get_value(DSMG600_PB_GPIO)) {

		/* IO Pin is 1 (button pushed) */
		if (power_button_countdown > 0)
			power_button_countdown--;

	} else {

		/* Done on button release, to allow for auto-power-on mods. */
		if (power_button_countdown == 0) {
			/* Signal init to do the ctrlaltdel action,
			 * this will bypass init if it hasn't started
			 * and do a kernel_restart.
			 */
			ctrl_alt_del();

			/* Change the state of the power LED to "blink" */
			gpio_set_value(DSMG600_LED_PWR_GPIO, 0);
		} else {
			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
		}
	}

	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
}

static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
{
	/* This is the paper-clip reset, it shuts the machine down directly. */
	machine_power_off();

	return IRQ_HANDLED;
}

static void __init dsmg600_timer_init(void)
{
    /* The xtal on this machine is non-standard. */
    ixp4xx_timer_freq = DSMG600_FREQ;

    /* Call standard timer_init function. */
    ixp4xx_timer_init();
}

static int __init dsmg600_gpio_init(void)
{
	if (!machine_is_dsmg600())
		return 0;

	gpio_request(DSMG600_RB_GPIO, "reset button");
	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
		IRQF_TRIGGER_LOW, "DSM-G600 reset button", NULL) < 0) {

		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
			gpio_to_irq(DSMG600_RB_GPIO));
	}

	/*
	 * The power button on the D-Link DSM-G600 is on GPIO 15, but
	 * it cannot handle interrupts on that GPIO line.  So we'll
	 * have to poll it with a kernel timer.
	 */

	/* Make sure that the power button GPIO is set up as an input */
	gpio_request(DSMG600_PB_GPIO, "power button");
	gpio_direction_input(DSMG600_PB_GPIO);
	/* Request poweroff GPIO line */
	gpio_request(DSMG600_PO_GPIO, "power off button");

	/* Set the initial value for the power button IRQ handler */
	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;

	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
	return 0;
}
device_initcall(dsmg600_gpio_init);

static void __init dsmg600_init(void)
{
	ixp4xx_sys_init();

	/* Make sure that GPIO14 and GPIO15 are not used as clocks */
	*IXP4XX_GPIO_GPCLKR = 0;

	dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
	dsmg600_flash_resource.end =
		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;

	i2c_register_board_info(0, dsmg600_i2c_board_info,
				ARRAY_SIZE(dsmg600_i2c_board_info));

	/* The UART is required on the DSM-G600 (Redboot cannot use the
	 * NIC) -- do it here so that it does *not* get removed if
	 * platform_add_devices fails!
         */
        (void)platform_device_register(&dsmg600_uart);

	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));

	pm_power_off = dsmg600_power_off;
}

MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
	/* Maintainer: www.nslu2-linux.org */
	.atag_offset	= 0x100,
	.map_io		= ixp4xx_map_io,
	.init_early	= ixp4xx_init_early,
	.init_irq	= ixp4xx_init_irq,
	.init_time	= dsmg600_timer_init,
	.init_machine	= dsmg600_init,
#if defined(CONFIG_PCI)
	.dma_zone_size	= SZ_64M,
#endif
	.restart	= ixp4xx_restart,
MACHINE_END