1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
/*
* Setup code for AT91SAM Evaluation Kits with Device Tree support
*
* Covers: * AT91SAM9G45-EKES board
* * AT91SAM9M10-EKES board
* * AT91SAM9M10G45-EK board
*
* Copyright (C) 2011 Atmel,
* 2011 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/gpio.h>
#include <linux/irqdomain.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/system_rev.h>
#include <mach/at91sam9_smc.h>
#include <asm/setup.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include "sam9_smc.h"
#include "generic.h"
static void __init ek_init_early(void)
{
/* Initialize processor: 12.000 MHz crystal */
at91_initialize(12000000);
/* DGBU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
/* det_pin is not connected */
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.det_pin = -EINVAL,
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
};
static struct sam9_smc_config __initdata ek_nand_smc_config = {
.ncs_read_setup = 0,
.nrd_setup = 2,
.ncs_write_setup = 0,
.nwe_setup = 2,
.ncs_read_pulse = 4,
.nrd_pulse = 4,
.ncs_write_pulse = 4,
.nwe_pulse = 4,
.read_cycle = 7,
.write_cycle = 7,
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
.tdf_cycles = 3,
};
static void __init ek_add_device_nand(void)
{
ek_nand_data.bus_width_16 = board_have_nand_16bit();
/* setup bus-width (8 or 16) */
if (ek_nand_data.bus_width_16)
ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
else
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
sam9_smc_configure(0, 3, &ek_nand_smc_config);
at91_add_device_nand(&ek_nand_data);
}
static const struct of_device_id aic_of_match[] __initconst = {
{ .compatible = "atmel,at91rm9200-aic", },
{},
};
static void __init at91_dt_init_irq(void)
{
irq_domain_generate_simple(aic_of_match, 0xfffff000, 0);
at91_init_irq_default();
}
static void __init at91_dt_device_init(void)
{
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
/* NAND */
ek_add_device_nand();
}
static const char *at91_dt_board_compat[] __initdata = {
"atmel,at91sam9m10g45ek",
"calao,usb-a9g20",
NULL
};
DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)")
/* Maintainer: Atmel */
.timer = &at91sam926x_timer,
.map_io = at91_map_io,
.init_early = ek_init_early,
.init_irq = at91_dt_init_irq,
.init_machine = at91_dt_device_init,
.dt_compat = at91_dt_board_compat,
MACHINE_END
|
