1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
|
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Netgear WG302v2 based on IXP422BB
* Derived from boardfiles written by Imre Kaloz
*/
/dts-v1/;
#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Netgear WG302 v1";
compatible = "netgear,wg302v1", "intel,ixp42x";
#address-cells = <1>;
#size-cells = <1>;
memory@0 {
/* 32 MB SDRAM according to boot arguments */
device_type = "memory";
reg = <0x00000000 0x02000000>;
};
chosen {
/* The RedBoot comes up in 9600 baud so let's keep this */
bootargs = "console=ttyS0,9600n8";
stdout-path = "uart1:9600n8";
};
aliases {
/* These are switched around */
serial0 = &uart1;
};
soc {
bus@c4000000 {
flash@0,0 {
compatible = "intel,ixp4xx-flash", "cfi-flash";
bank-width = <2>;
/*
* 8 MB of Flash in 64 0x20000 sized blocks
* mapped in at CS0.
*/
reg = <0 0x00000000 0x800000>;
/* Configure expansion bus to allow writes */
intel,ixp4xx-eb-write-enable = <1>;
partitions {
compatible = "redboot-fis";
fis-index-block = <0x3f>;
};
};
};
pci@c0000000 {
status = "okay";
/*
* Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
* We have slots (IDSEL) 1 and 2 with one assigned IRQ
* each handling all IRQs.
*/
#interrupt-cells = <1>;
interrupt-map-mask = <0xf800 0 0 7>;
interrupt-map =
/* IDSEL 1 */
<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
/* IDSEL 2 */
<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
};
ethernet@c8009000 {
status = "okay";
queue-rx = <&qmgr 3>;
queue-txready = <&qmgr 20>;
phy-mode = "rgmii";
phy-handle = <&phy30>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy30: ethernet-phy@30 {
reg = <30>;
};
};
};
};
};
|
