blob: 8a5fd1611c6f2590194ff3d39a3c7b3846e15853 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
Documentation for CMI 8330 (SoundPRO)
-------------------------------------
Alessandro Zummo <azummo@ita.flashnet.it>
( Be sure to read Documentation/sound/oss/SoundPro too )
This adapter is now directly supported by the sb driver.
The only thing you have to do is to compile the kernel sound
support as a module and to enable kernel ISAPnP support,
as shown below.
CONFIG_SOUND=m
CONFIG_SOUND_SB=m
CONFIG_PNP=y
CONFIG_ISAPNP=y
and optionally:
CONFIG_SOUND_MPU401=m
for MPU401 support.
(I suggest you to use "make menuconfig" or "make xconfig"
for a more comfortable configuration editing)
Then you can do
modprobe sb
and everything will be (hopefully) configured.
You should get something similar in syslog:
sb: CMI8330 detected.
sb: CMI8330 sb base located at 0x220
sb: CMI8330 mpu base located at 0x330
sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it>
sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5
The old documentation file follows for reference
purposes.
How to enable CMI 8330 (SOUNDPRO) soundchip on Linux
------------------------------------------
Stefan Laudat <Stefan.Laudat@asit.ro>
[Note: The CMI 8338 is unrelated and is supported by cmpci.o]
In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but
you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/.
Of course you will have to compile kernel sound support as module, as shown below:
CONFIG_SOUND=m
CONFIG_SOUND_OSS=m
CONFIG_SOUND_SB=m
CONFIG_SOUND_ADLIB=m
CONFIG_SOUND_MPU401=m
# Mikro$chaft sound system (kinda useful here ;))
CONFIG_SOUND_MSS=m
The /etc/isapnp.conf file will be:
<snip below>
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
(VERIFYLD N)
# WSS
(CONFIGURE CMI0001/16777472 (LD 0
(IO 0 (SIZE 8) (BASE 0x0530))
(IO 1 (SIZE 8) (BASE 0x0388))
(INT 0 (IRQ 7 (MODE +E)))
(DMA 0 (CHANNEL 0))
(NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}")
(ACT Y)
))
# MPU
(CONFIGURE CMI0001/16777472 (LD 1
(IO 0 (SIZE 2) (BASE 0x0330))
(INT 0 (IRQ 11 (MODE +E)))
(NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}")
(ACT Y)
))
# Joystick
(CONFIGURE CMI0001/16777472 (LD 2
(IO 0 (SIZE 8) (BASE 0x0200))
(NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}")
(ACT Y)
))
# SoundBlaster
(CONFIGURE CMI0001/16777472 (LD 3
(IO 0 (SIZE 16) (BASE 0x0220))
(INT 0 (IRQ 5 (MODE +E)))
(DMA 0 (CHANNEL 1))
(DMA 1 (CHANNEL 5))
(NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}")
(ACT Y)
))
(WAITFORKEY)
<end of snip>
The module sequence is trivial:
/sbin/insmod soundcore
/sbin/insmod sound
/sbin/insmod uart401
# insert this first
/sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1
# The sb module is an alternative to the ad1848 (Microsoft Sound System)
# Anyhow, this is full duplex and has MIDI
/sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330
Alma Chao <elysian@ethereal.torsion.org> suggests the following in
a /etc/modprobe.d/*conf file:
alias sound ad1848
alias synth0 opl3
options ad1848 io=0x530 irq=7 dma=0 soundpro=1
options opl3 io=0x388
|
