blob: 189bab09255a929089ffd031d10c71386964b69e (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
|
SD and MMC Block Device Attributes
==================================
These attributes are defined for the block devices associated with the
SD or MMC device.
The following attributes are read/write.
force_ro Enforce read-only access even if write protect switch is off.
SD and MMC Device Attributes
============================
All attributes are read-only.
cid Card Identifaction Register
csd Card Specific Data Register
scr SD Card Configuration Register (SD only)
date Manufacturing Date (from CID Register)
fwrev Firmware/Product Revision (from CID Register) (SD and MMCv1 only)
hwrev Hardware/Product Revision (from CID Register) (SD and MMCv1 only)
manfid Manufacturer ID (from CID Register)
name Product Name (from CID Register)
oemid OEM/Application ID (from CID Register)
prv Product Revision (from CID Register) (SD and MMCv4 only)
serial Product Serial Number (from CID Register)
erase_size Erase group size
preferred_erase_size Preferred erase size
raw_rpmb_size_mult RPMB partition size
rel_sectors Reliable write sector count
Note on Erase Size and Preferred Erase Size:
"erase_size" is the minimum size, in bytes, of an erase
operation. For MMC, "erase_size" is the erase group size
reported by the card. Note that "erase_size" does not apply
to trim or secure trim operations where the minimum size is
always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on
the card wait. This is not a problem if the whole card
is being erased, but erasing one partition will make
I/O for another partition on the same card wait for the
duration of the erase - which could be a several
minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very
useful. Because the erase timeout contains a margin
which is multiplied by the size of the erase area,
the value can end up being several minutes for large
areas.
"erase_size" is not the most efficient unit to erase
(especially for SD where it is just one sector),
hence "preferred_erase_size" provides a good chunk
size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity
erase size if a card specifies one, otherwise it is
based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit
size specified by the card.
"preferred_erase_size" is in bytes.
Note on raw_rpmb_size_mult:
"raw_rpmb_size_mult" is a mutliple of 128kB block.
RPMB size in byte is calculated by using the following equation:
RPMB partition size = 128kB x raw_rpmb_size_mult
SD/MMC/SDIO Clock Gating Attribute
==================================
Read and write access is provided to following attribute.
This attribute appears only if CONFIG_MMC_CLKGATE is enabled.
clkgate_delay Tune the clock gating delay with desired value in milliseconds.
echo <desired delay> > /sys/class/mmc_host/mmcX/clkgate_delay
|
