1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
|
* Freescale (Enhanced) Configurable Serial Peripheral Interface
(CSPI/eCSPI) for i.MX
Required properties:
- compatible :
- "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1
- "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21
- "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27
- "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31
- "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35
- "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
- "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
- "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8MQ
- "fsl,imx8mm-ecspi" for SPI compatible with the one integrated on i.MX8MM
- "fsl,imx8mn-ecspi" for SPI compatible with the one integrated on i.MX8MN
- "fsl,imx8mp-ecspi" for SPI compatible with the one integrated on i.MX8MP
- reg : Offset and length of the register set for the device
- interrupts : Should contain CSPI/eCSPI interrupt
- clocks : Clock specifiers for both ipg and per clocks.
- clock-names : Clock names should include both "ipg" and "per"
See the clock consumer binding,
Documentation/devicetree/bindings/clock/clock-bindings.txt
Recommended properties:
- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip
select lines can be used, they appear to always generate a pulse between each
word of a transfer. Most use cases will require GPIO based chip selects to
generate a valid transaction.
Optional properties:
- num-cs : Number of total chip selects, see spi-bus.txt.
- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
Documentation/devicetree/bindings/dma/dma.txt.
- dma-names: DMA request names, if present, should include "tx" and "rx".
- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register
controlling the SPI_READY handling. Note that to enable the DRCTL consideration,
the SPI_READY mode-flag needs to be set too.
Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst).
Obsolete properties:
- fsl,spi-num-chipselects : Contains the number of the chipselect
Example:
ecspi@70010000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx51-ecspi";
reg = <0x70010000 0x4000>;
interrupts = <36>;
cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
<&gpio3 25 0>; /* GPIO3_25 */
dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
dma-names = "rx", "tx";
fsl,spi-rdy-drctl = <1>;
};
|
