From cc904c7188c29847817f35e6966fec3014c7479b Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 14 Mar 2013 08:35:06 +0200 Subject: iwlwifi: fix length check in multi-TB HCMD As reported by Ben Hutchings, there was a harmless issue in the checks being done on the lengths of the TBs while building the TFD for a multi-TB host command. Cc: stable@vger@kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/tx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/tx.c b/drivers/net/wireless/iwlwifi/pcie/tx.c index 8595c16f74de..cb5c6792e3a8 100644 --- a/drivers/net/wireless/iwlwifi/pcie/tx.c +++ b/drivers/net/wireless/iwlwifi/pcie/tx.c @@ -1264,7 +1264,7 @@ static int iwl_pcie_enqueue_hcmd(struct iwl_trans *trans, for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { int copy = 0; - if (!cmd->len) + if (!cmd->len[i]) continue; /* need at least IWL_HCMD_SCRATCHBUF_SIZE copied */ -- cgit v1.2.3 From 4620020b5d7ca34d1c03fa98b0ca457320cb7d71 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Wed, 13 Mar 2013 16:38:32 +0200 Subject: iwlwifi: set rfkill in internal state of the transport We didn't update the internal of the PCIe transport when we read the RFkill state directly. Fix that. Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/trans.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c index 17bedc50e753..12c4f31ca8fb 100644 --- a/drivers/net/wireless/iwlwifi/pcie/trans.c +++ b/drivers/net/wireless/iwlwifi/pcie/trans.c @@ -475,6 +475,10 @@ static int iwl_trans_pcie_start_fw(struct iwl_trans *trans, /* If platform's RF_KILL switch is NOT set to KILL */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); if (hw_rfkill && !run_in_rfkill) return -ERFKILL; @@ -641,6 +645,7 @@ static int iwl_trans_pcie_d3_resume(struct iwl_trans *trans, static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) { + struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); bool hw_rfkill; int err; @@ -656,6 +661,10 @@ static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) iwl_enable_rfkill_int(trans); hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); return 0; @@ -694,6 +703,10 @@ static void iwl_trans_pcie_stop_hw(struct iwl_trans *trans, * op_mode. */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); } } -- cgit v1.2.3 From 2d5d50ee596361566f7f84300117cba7d7672bc5 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 31 Jan 2013 15:03:55 +0200 Subject: iwlwifi: dvm: don't send HCMD in restart flow There is a race between the restart flow and the workers. The workers are cancelled after the fw is already killed and might send HCMD when there is fw to handle them. Simply check that there is a fw to which the HCMD can be sent before actually sending it. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/dvm/lib.c | 9 +++++++++ drivers/net/wireless/iwlwifi/dvm/ucode.c | 4 ++-- 2 files changed, 11 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/dvm/lib.c b/drivers/net/wireless/iwlwifi/dvm/lib.c index 86ea5f4c3939..44ca0e57f9f7 100644 --- a/drivers/net/wireless/iwlwifi/dvm/lib.c +++ b/drivers/net/wireless/iwlwifi/dvm/lib.c @@ -1261,6 +1261,15 @@ int iwl_dvm_send_cmd(struct iwl_priv *priv, struct iwl_host_cmd *cmd) return -EIO; } + /* + * This can happen upon FW ASSERT: we clear the STATUS_FW_ERROR flag + * in iwl_down but cancel the workers only later. + */ + if (!priv->ucode_loaded) { + IWL_ERR(priv, "Fw not loaded - dropping CMD: %x\n", cmd->id); + return -EIO; + } + /* * Synchronous commands from this op-mode must hold * the mutex, this ensures we don't try to send two diff --git a/drivers/net/wireless/iwlwifi/dvm/ucode.c b/drivers/net/wireless/iwlwifi/dvm/ucode.c index 736fe9bb140e..1a4ac9236a44 100644 --- a/drivers/net/wireless/iwlwifi/dvm/ucode.c +++ b/drivers/net/wireless/iwlwifi/dvm/ucode.c @@ -367,6 +367,8 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return -EIO; } + priv->ucode_loaded = true; + if (ucode_type != IWL_UCODE_WOWLAN) { /* delay a bit to give rfkill time to run */ msleep(5); @@ -380,8 +382,6 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return ret; } - priv->ucode_loaded = true; - return 0; } -- cgit v1.2.3 From 0f49d64c95944f5701216e900b89aab749edcda2 Mon Sep 17 00:00:00 2001 From: Avinash Patil Date: Wed, 20 Mar 2013 17:56:23 -0700 Subject: mwifiex: reset skb->data after processing PCIe sleep confirm cmd respose This patch is a bug fix for an issue wherein power save was not working for PCIe. This happens because for processing power save sleep confirm command we pull skb so that skb->data points ahead of interface header. We use same skb to get other cmda responses as well. So if we don't push skb after processing cmd response, it results into reduction in skb->len and finally skb->len reaches zero. This causes failure in processing sleep command response. Fix this by pushing skb by INTF_HEADER_LEN at the end of command response processing. Signed-off-by: Avinash Patil Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/pcie.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/pcie.c b/drivers/net/wireless/mwifiex/pcie.c index 5c395e2e6a2b..feb204613397 100644 --- a/drivers/net/wireless/mwifiex/pcie.c +++ b/drivers/net/wireless/mwifiex/pcie.c @@ -1508,6 +1508,7 @@ static int mwifiex_pcie_process_cmd_complete(struct mwifiex_adapter *adapter) } memcpy(adapter->upld_buf, skb->data, min_t(u32, MWIFIEX_SIZE_OF_CMD_BUFFER, skb->len)); + skb_push(skb, INTF_HEADER_LEN); if (mwifiex_map_pci_memory(adapter, skb, MWIFIEX_UPLD_SIZE, PCI_DMA_FROMDEVICE)) return -1; -- cgit v1.2.3 From d6b057b5dbba97e6ba13aace5270babd7c8b658c Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:35 +0000 Subject: e1000: ethtool: Add missing dma_mapping_error-call in e1000_setup_desc_rings After dma_map_single, dma_mapping_error must be called. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c index 43462d596a4e..ffd287196bf8 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c +++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c @@ -1053,6 +1053,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) txdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE); + if (dma_mapping_error(&pdev->dev, txdr->buffer_info[i].dma)) { + ret_val = 4; + goto err_nomem; + } tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma); tx_desc->lower.data = cpu_to_le32(skb->len); tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP | @@ -1069,7 +1073,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info = kcalloc(rxdr->count, sizeof(struct e1000_buffer), GFP_KERNEL); if (!rxdr->buffer_info) { - ret_val = 4; + ret_val = 5; goto err_nomem; } @@ -1077,7 +1081,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->desc = dma_alloc_coherent(&pdev->dev, rxdr->size, &rxdr->dma, GFP_KERNEL); if (!rxdr->desc) { - ret_val = 5; + ret_val = 6; goto err_nomem; } memset(rxdr->desc, 0, rxdr->size); @@ -1101,7 +1105,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, GFP_KERNEL); if (!skb) { - ret_val = 6; + ret_val = 7; goto err_nomem; } skb_reserve(skb, NET_IP_ALIGN); @@ -1110,6 +1114,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, E1000_RXBUFFER_2048, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, rxdr->buffer_info[i].dma)) { + ret_val = 8; + goto err_nomem; + } rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma); memset(skb->data, 0x00, skb->len); } -- cgit v1.2.3 From 065946c65a61943b4c609a0a1b1bac6742b3b593 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:41 +0000 Subject: ixgb: Add missing dma_mapping_error-call in ixgb_alloc_rx_buffers After dma_map_single, dma_mapping_error must be called. It seems safe to not free the skb allocated in this function, as the skb can be reused later. Additionally this patch fixes one coding-style error. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgb/ixgb_main.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgb/ixgb_main.c b/drivers/net/ethernet/intel/ixgb/ixgb_main.c index ea4808373435..b5f94abe3cff 100644 --- a/drivers/net/ethernet/intel/ixgb/ixgb_main.c +++ b/drivers/net/ethernet/intel/ixgb/ixgb_main.c @@ -2159,6 +2159,10 @@ map_skb: skb->data, adapter->rx_buffer_len, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } rx_desc = IXGB_RX_DESC(*rx_ring, i); rx_desc->buff_addr = cpu_to_le64(buffer_info->dma); @@ -2168,7 +2172,8 @@ map_skb: rx_desc->status = 0; - if (++i == rx_ring->count) i = 0; + if (++i == rx_ring->count) + i = 0; buffer_info = &rx_ring->buffer_info[i]; } -- cgit v1.2.3 From 37287fae7e4506fb0822523587c769783164cdd6 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:46 +0000 Subject: e1000e: Add missing dma_mapping_error-call in e1000_alloc_jumbo_rx_buffers After dma_map_page, dma_mapping_error must be called. It seems safe to not free the skb/page allocated in this function, as the skb/page can be reused later. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/netdev.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 948b86ffa4f0..7e615e2bf7e6 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -848,11 +848,16 @@ check_page: } } - if (!buffer_info->dma) + if (!buffer_info->dma) { buffer_info->dma = dma_map_page(&pdev->dev, buffer_info->page, 0, PAGE_SIZE, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } + } rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); -- cgit v1.2.3 From f901b6bc404b67d96eca739857c097e022727b71 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 11:36:42 +0100 Subject: can: sja1000: fix define conflict on SH Thias patch fixes a define conflict between the SH architecture and the sja1000 driver: drivers/net/can/sja1000/sja1000.h:59:0: warning: "REG_SR" redefined [enabled by default] arch/sh/include/asm/ptrace_32.h:25:0: note: this is the location of the previous definition A SJA1000_ prefix is added to the offending sja1000 define only, to make a minimal patch suited for stable. A later patch will add a SJA1000_ prefix to all defines in sja1000.h. Cc: linux-stable Reported-by: Fengguang Wu Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/plx_pci.c | 4 ++-- drivers/net/can/sja1000/sja1000.c | 6 +++--- drivers/net/can/sja1000/sja1000.h | 2 +- 3 files changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c index a042cdc260dc..3c18d7d000ed 100644 --- a/drivers/net/can/sja1000/plx_pci.c +++ b/drivers/net/can/sja1000/plx_pci.c @@ -348,7 +348,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) */ if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) == REG_CR_BASICCAN_INITIAL && - (priv->read_reg(priv, REG_SR) == REG_SR_BASICCAN_INITIAL) && + (priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_BASICCAN_INITIAL) && (priv->read_reg(priv, REG_IR) == REG_IR_BASICCAN_INITIAL)) flag = 1; @@ -360,7 +360,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) * See states on p. 23 of the Datasheet. */ if (priv->read_reg(priv, REG_MOD) == REG_MOD_PELICAN_INITIAL && - priv->read_reg(priv, REG_SR) == REG_SR_PELICAN_INITIAL && + priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_PELICAN_INITIAL && priv->read_reg(priv, REG_IR) == REG_IR_PELICAN_INITIAL) return flag; diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index daf4013a8fc7..e4df307eaa90 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -92,7 +92,7 @@ static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) */ spin_lock_irqsave(&priv->cmdreg_lock, flags); priv->write_reg(priv, REG_CMR, val); - priv->read_reg(priv, REG_SR); + priv->read_reg(priv, SJA1000_REG_SR); spin_unlock_irqrestore(&priv->cmdreg_lock, flags); } @@ -502,7 +502,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) while ((isrc = priv->read_reg(priv, REG_IR)) && (n < SJA1000_MAX_IRQ)) { n++; - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller due to hw unplug */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; @@ -530,7 +530,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) /* receive interrupt */ while (status & SR_RBS) { sja1000_rx(dev); - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; diff --git a/drivers/net/can/sja1000/sja1000.h b/drivers/net/can/sja1000/sja1000.h index afa99847a510..aa48e053da27 100644 --- a/drivers/net/can/sja1000/sja1000.h +++ b/drivers/net/can/sja1000/sja1000.h @@ -56,7 +56,7 @@ /* SJA1000 registers - manual section 6.4 (Pelican Mode) */ #define REG_MOD 0x00 #define REG_CMR 0x01 -#define REG_SR 0x02 +#define SJA1000_REG_SR 0x02 #define REG_IR 0x03 #define REG_IER 0x04 #define REG_ALC 0x0B -- cgit v1.2.3 From 3fd33497f80aa528ded0db2851b48638635d5caa Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 12:47:13 +0100 Subject: can: sja1000: limit PEAK PCAN-PC Card to HAS_IOPORT This patch limits the PEAK PCAN-PC Card driver to systems with ioports. Fixes a compile time breakage on SH: drivers/net/can/sja1000/peak_pcmcia.c:626:2: error: implicit declaration of function 'ioport_unmap' Reported-by: Fengguang Wu Cc: Paul Mundt Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig index b39ca5b3ea7f..ff2ba86cd4a4 100644 --- a/drivers/net/can/sja1000/Kconfig +++ b/drivers/net/can/sja1000/Kconfig @@ -46,6 +46,7 @@ config CAN_EMS_PCI config CAN_PEAK_PCMCIA tristate "PEAK PCAN-PC Card" depends on PCMCIA + depends on HAS_IOPORT ---help--- This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels) from PEAK-System (http://www.peak-system.com). To compile this -- cgit v1.2.3 From 54683441a92ebe20c5282465ea6f21e5e74d2974 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Wed, 27 Mar 2013 10:52:11 -0400 Subject: Revert "brcmsmac: support 4313iPA" This reverts commit b6fc28a158076ca2764edc9a6d1e1402f56e1c0c. This commit is reported to cause a regression in the support for some revisions of 4313 ePA devices. http://marc.info/?l=linux-wireless&m=136360340200943&w=2 Conflicts: drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c Reported-by: David Herrmann Signed-off-by: John W. Linville --- .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 369 ++++++++------------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 64 ++-- 2 files changed, 162 insertions(+), 271 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c index 21a824232478..18d37645e2cd 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c @@ -1137,9 +1137,8 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, gain0_15 = ((biq1 & 0xf) << 12) | ((tia & 0xf) << 8) | ((lna2 & 0x3) << 6) | - ((lna2 & 0x3) << 4) | - ((lna1 & 0x3) << 2) | - ((lna1 & 0x3) << 0); + ((lna2 & + 0x3) << 4) | ((lna1 & 0x3) << 2) | ((lna1 & 0x3) << 0); mod_phy_reg(pi, 0x4b6, (0xffff << 0), gain0_15 << 0); mod_phy_reg(pi, 0x4b7, (0xf << 0), gain16_19 << 0); @@ -1157,8 +1156,6 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, } mod_phy_reg(pi, 0x44d, (0x1 << 0), (!trsw) << 0); - mod_phy_reg(pi, 0x4b1, (0x3 << 11), lna1 << 11); - mod_phy_reg(pi, 0x4e6, (0x3 << 3), lna1 << 3); } @@ -1331,43 +1328,6 @@ static u32 wlc_lcnphy_measure_digital_power(struct brcms_phy *pi, u16 nsamples) return (iq_est.i_pwr + iq_est.q_pwr) / nsamples; } -static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain, - u16 tia_gain, u16 lna2_gain) -{ - u32 i_thresh_l, q_thresh_l; - u32 i_thresh_h, q_thresh_h; - struct lcnphy_iq_est iq_est_h, iq_est_l; - - wlc_lcnphy_set_rx_gain_by_distribution(pi, 0, 0, 0, biq1_gain, tia_gain, - lna2_gain, 0); - - wlc_lcnphy_rx_gain_override_enable(pi, true); - wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l)) - return false; - - wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h)) - return false; - - i_thresh_l = (iq_est_l.i_pwr << 1); - i_thresh_h = (iq_est_l.i_pwr << 2) + iq_est_l.i_pwr; - - q_thresh_l = (iq_est_l.q_pwr << 1); - q_thresh_h = (iq_est_l.q_pwr << 2) + iq_est_l.q_pwr; - if ((iq_est_h.i_pwr > i_thresh_l) && - (iq_est_h.i_pwr < i_thresh_h) && - (iq_est_h.q_pwr > q_thresh_l) && - (iq_est_h.q_pwr < q_thresh_h)) - return true; - - return false; -} - static bool wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, const struct lcnphy_rx_iqcomp *iqcomp, @@ -1382,8 +1342,8 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, RFOverrideVal0_old, rfoverride2_old, rfoverride2val_old, rfoverride3_old, rfoverride3val_old, rfoverride4_old, rfoverride4val_old, afectrlovr_old, afectrlovrval_old; - int tia_gain, lna2_gain, biq1_gain; - bool set_gain; + int tia_gain; + u32 received_power, rx_pwr_threshold; u16 old_sslpnCalibClkEnCtrl, old_sslpnRxFeClkEnCtrl; u16 values_to_save[11]; s16 *ptr; @@ -1408,134 +1368,126 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, goto cal_done; } - WARN_ON(module != 1); - tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - - for (i = 0; i < 11; i++) - values_to_save[i] = - read_radio_reg(pi, rxiq_cal_rf_reg[i]); - Core1TxControl_old = read_phy_reg(pi, 0x631); - - or_phy_reg(pi, 0x631, 0x0015); - - RFOverride0_old = read_phy_reg(pi, 0x44c); - RFOverrideVal0_old = read_phy_reg(pi, 0x44d); - rfoverride2_old = read_phy_reg(pi, 0x4b0); - rfoverride2val_old = read_phy_reg(pi, 0x4b1); - rfoverride3_old = read_phy_reg(pi, 0x4f9); - rfoverride3val_old = read_phy_reg(pi, 0x4fa); - rfoverride4_old = read_phy_reg(pi, 0x938); - rfoverride4val_old = read_phy_reg(pi, 0x939); - afectrlovr_old = read_phy_reg(pi, 0x43b); - afectrlovrval_old = read_phy_reg(pi, 0x43c); - old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); - old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); - - tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); - if (tx_gain_override_old) { - wlc_lcnphy_get_tx_gain(pi, &old_gains); - tx_gain_index_old = pi_lcn->lcnphy_current_index; - } - - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); + if (module == 1) { - mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); + tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); + wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); + for (i = 0; i < 11; i++) + values_to_save[i] = + read_radio_reg(pi, rxiq_cal_rf_reg[i]); + Core1TxControl_old = read_phy_reg(pi, 0x631); + + or_phy_reg(pi, 0x631, 0x0015); + + RFOverride0_old = read_phy_reg(pi, 0x44c); + RFOverrideVal0_old = read_phy_reg(pi, 0x44d); + rfoverride2_old = read_phy_reg(pi, 0x4b0); + rfoverride2val_old = read_phy_reg(pi, 0x4b1); + rfoverride3_old = read_phy_reg(pi, 0x4f9); + rfoverride3val_old = read_phy_reg(pi, 0x4fa); + rfoverride4_old = read_phy_reg(pi, 0x938); + rfoverride4val_old = read_phy_reg(pi, 0x939); + afectrlovr_old = read_phy_reg(pi, 0x43b); + afectrlovrval_old = read_phy_reg(pi, 0x43c); + old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); + old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); + + tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); + if (tx_gain_override_old) { + wlc_lcnphy_get_tx_gain(pi, &old_gains); + tx_gain_index_old = pi_lcn->lcnphy_current_index; + } - write_radio_reg(pi, RADIO_2064_REG116, 0x06); - write_radio_reg(pi, RADIO_2064_REG12C, 0x07); - write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); - write_radio_reg(pi, RADIO_2064_REG098, 0x03); - write_radio_reg(pi, RADIO_2064_REG00B, 0x7); - mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); - write_radio_reg(pi, RADIO_2064_REG01D, 0x01); - write_radio_reg(pi, RADIO_2064_REG114, 0x01); - write_radio_reg(pi, RADIO_2064_REG02E, 0x10); - write_radio_reg(pi, RADIO_2064_REG12A, 0x08); - - mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); - mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); - mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); - mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); - write_phy_reg(pi, 0x6da, 0xffff); - or_phy_reg(pi, 0x6db, 0x3); + mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); - wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); - set_gain = false; - - lna2_gain = 3; - while ((lna2_gain >= 0) && !set_gain) { - tia_gain = 4; - - while ((tia_gain >= 0) && !set_gain) { - biq1_gain = 6; - - while ((biq1_gain >= 0) && !set_gain) { - set_gain = wlc_lcnphy_rx_iq_cal_gain(pi, - (u16) - biq1_gain, - (u16) - tia_gain, - (u16) - lna2_gain); - biq1_gain -= 1; - } + write_radio_reg(pi, RADIO_2064_REG116, 0x06); + write_radio_reg(pi, RADIO_2064_REG12C, 0x07); + write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); + write_radio_reg(pi, RADIO_2064_REG098, 0x03); + write_radio_reg(pi, RADIO_2064_REG00B, 0x7); + mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); + write_radio_reg(pi, RADIO_2064_REG01D, 0x01); + write_radio_reg(pi, RADIO_2064_REG114, 0x01); + write_radio_reg(pi, RADIO_2064_REG02E, 0x10); + write_radio_reg(pi, RADIO_2064_REG12A, 0x08); + + mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); + mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + + mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + + wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0); + write_phy_reg(pi, 0x6da, 0xffff); + or_phy_reg(pi, 0x6db, 0x3); + wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); + wlc_lcnphy_rx_gain_override_enable(pi, true); + + tia_gain = 8; + rx_pwr_threshold = 950; + while (tia_gain > 0) { tia_gain -= 1; + wlc_lcnphy_set_rx_gain_by_distribution(pi, + 0, 0, 2, 2, + (u16) + tia_gain, 1, 0); + udelay(500); + + received_power = + wlc_lcnphy_measure_digital_power(pi, 2000); + if (received_power < rx_pwr_threshold) + break; } - lna2_gain -= 1; - } + result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff); - if (set_gain) - result = wlc_lcnphy_calc_rx_iq_comp(pi, 1024); - else - result = false; + wlc_lcnphy_stop_tx_tone(pi); - wlc_lcnphy_stop_tx_tone(pi); + write_phy_reg(pi, 0x631, Core1TxControl_old); - write_phy_reg(pi, 0x631, Core1TxControl_old); - - write_phy_reg(pi, 0x44c, RFOverrideVal0_old); - write_phy_reg(pi, 0x44d, RFOverrideVal0_old); - write_phy_reg(pi, 0x4b0, rfoverride2_old); - write_phy_reg(pi, 0x4b1, rfoverride2val_old); - write_phy_reg(pi, 0x4f9, rfoverride3_old); - write_phy_reg(pi, 0x4fa, rfoverride3val_old); - write_phy_reg(pi, 0x938, rfoverride4_old); - write_phy_reg(pi, 0x939, rfoverride4val_old); - write_phy_reg(pi, 0x43b, afectrlovr_old); - write_phy_reg(pi, 0x43c, afectrlovrval_old); - write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); - write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); + write_phy_reg(pi, 0x44c, RFOverrideVal0_old); + write_phy_reg(pi, 0x44d, RFOverrideVal0_old); + write_phy_reg(pi, 0x4b0, rfoverride2_old); + write_phy_reg(pi, 0x4b1, rfoverride2val_old); + write_phy_reg(pi, 0x4f9, rfoverride3_old); + write_phy_reg(pi, 0x4fa, rfoverride3val_old); + write_phy_reg(pi, 0x938, rfoverride4_old); + write_phy_reg(pi, 0x939, rfoverride4val_old); + write_phy_reg(pi, 0x43b, afectrlovr_old); + write_phy_reg(pi, 0x43c, afectrlovrval_old); + write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); + write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); - wlc_lcnphy_clear_trsw_override(pi); + wlc_lcnphy_clear_trsw_override(pi); - mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); + mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); - for (i = 0; i < 11; i++) - write_radio_reg(pi, rxiq_cal_rf_reg[i], - values_to_save[i]); + for (i = 0; i < 11; i++) + write_radio_reg(pi, rxiq_cal_rf_reg[i], + values_to_save[i]); - if (tx_gain_override_old) - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); - else - wlc_lcnphy_disable_tx_gain_override(pi); + if (tx_gain_override_old) + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); + else + wlc_lcnphy_disable_tx_gain_override(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); - wlc_lcnphy_rx_gain_override_enable(pi, false); + wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); + wlc_lcnphy_rx_gain_override_enable(pi, false); + } cal_done: kfree(ptr); @@ -1829,17 +1781,6 @@ wlc_lcnphy_radio_2064_channel_tune_4313(struct brcms_phy *pi, u8 channel) write_radio_reg(pi, RADIO_2064_REG038, 3); write_radio_reg(pi, RADIO_2064_REG091, 7); } - - if (!(pi->sh->boardflags & BFL_FEM)) { - u8 reg038[14] = {0xd, 0xe, 0xd, 0xd, 0xd, 0xc, - 0xa, 0xb, 0xb, 0x3, 0x3, 0x2, 0x0, 0x0}; - - write_radio_reg(pi, RADIO_2064_REG02A, 0xf); - write_radio_reg(pi, RADIO_2064_REG091, 0x3); - write_radio_reg(pi, RADIO_2064_REG038, 0x3); - - write_radio_reg(pi, RADIO_2064_REG038, reg038[channel - 1]); - } } static int @@ -2034,16 +1975,6 @@ wlc_lcnphy_set_tssi_mux(struct brcms_phy *pi, enum lcnphy_tssi_mode pos) } else { mod_radio_reg(pi, RADIO_2064_REG03A, 1, 0x1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x4, 1<<2); - mod_radio_reg(pi, RADIO_2064_REG036, 0x10, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x10, 1<<4); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x77); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, 0xe<<1); - mod_radio_reg(pi, RADIO_2064_REG112, 0x80, 1<<7); - mod_radio_reg(pi, RADIO_2064_REG005, 0x7, 1<<1); - mod_radio_reg(pi, RADIO_2064_REG029, 0xf0, 0<<4); } } else { mod_phy_reg(pi, 0x4d9, (0x1 << 2), (0x1) << 2); @@ -2130,14 +2061,12 @@ static void wlc_lcnphy_pwrctrl_rssiparams(struct brcms_phy *pi) (auxpga_vmid_temp << 0) | (auxpga_gain_temp << 12)); mod_radio_reg(pi, RADIO_2064_REG082, (1 << 5), (1 << 5)); - mod_radio_reg(pi, RADIO_2064_REG07C, (1 << 0), (1 << 0)); } static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) { struct phytbl_info tab; u32 rfseq, ind; - u8 tssi_sel; tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; @@ -2159,13 +2088,7 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x503, (0x1 << 4), (1) << 4); - if (pi->sh->boardflags & BFL_FEM) { - tssi_sel = 0x1; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); - } else { - tssi_sel = 0xe; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_POST_PA); - } + wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); mod_phy_reg(pi, 0x4a4, (0x1 << 14), (0) << 14); mod_phy_reg(pi, 0x4a4, (0x1 << 15), (1) << 15); @@ -2201,10 +2124,9 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x49a, (0x1ff << 0), (0xff) << 0); if (LCNREV_IS(pi->pubpi.phy_rev, 2)) { - mod_radio_reg(pi, RADIO_2064_REG028, 0xf, tssi_sel); + mod_radio_reg(pi, RADIO_2064_REG028, 0xf, 0xe); mod_radio_reg(pi, RADIO_2064_REG086, 0x4, 0x4); } else { - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, tssi_sel << 1); mod_radio_reg(pi, RADIO_2064_REG03A, 0x1, 1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 1 << 3); } @@ -2251,10 +2173,6 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x4d7, (0xf << 8), (0) << 8); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x0); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - wlc_lcnphy_pwrctrl_rssiparams(pi); } @@ -2873,8 +2791,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) read_radio_reg(pi, RADIO_2064_REG007) & 1; u16 SAVE_jtag_auxpga = read_radio_reg(pi, RADIO_2064_REG0FF) & 0x10; u16 SAVE_iqadc_aux_en = read_radio_reg(pi, RADIO_2064_REG11F) & 4; - u8 SAVE_bbmult = wlc_lcnphy_get_bbmult(pi); - idleTssi = read_phy_reg(pi, 0x4ab); suspend = (0 == (bcma_read32(pi->d11core, D11REGOFFS(maccontrol)) & MCTL_EN_MAC)); @@ -2892,12 +2808,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_radio_reg(pi, RADIO_2064_REG0FF, 0x10, 1 << 4); mod_radio_reg(pi, RADIO_2064_REG11F, 0x4, 1 << 2); wlc_lcnphy_tssi_setup(pi); - - mod_phy_reg(pi, 0x4d7, (0x1 << 0), (1 << 0)); - mod_phy_reg(pi, 0x4d7, (0x1 << 6), (1 << 6)); - - wlc_lcnphy_set_bbmult(pi, 0x0); - wlc_phy_do_dummy_tx(pi, true, OFF); idleTssi = ((read_phy_reg(pi, 0x4ab) & (0x1ff << 0)) >> 0); @@ -2919,7 +2829,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_phy_reg(pi, 0x44c, (0x1 << 12), (0) << 12); - wlc_lcnphy_set_bbmult(pi, SAVE_bbmult); wlc_lcnphy_set_tx_gain_override(pi, tx_gain_override_old); wlc_lcnphy_set_tx_gain(pi, &old_gains); wlc_lcnphy_set_tx_pwr_ctrl(pi, SAVE_txpwrctrl); @@ -3133,11 +3042,6 @@ static void wlc_lcnphy_tx_pwr_ctrl_init(struct brcms_phy_pub *ppi) wlc_lcnphy_write_table(pi, &tab); tab.tbl_offset++; } - mod_phy_reg(pi, 0x4d0, (0x1 << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 8), (0) << 8); - mod_phy_reg(pi, 0x4d0, (0x1 << 4), (0) << 4); - mod_phy_reg(pi, 0x4d0, (0x1 << 2), (0) << 2); mod_phy_reg(pi, 0x410, (0x1 << 7), (0) << 7); @@ -3939,6 +3843,7 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) target_gains.pad_gain = 21; target_gains.dac_gain = 0; wlc_lcnphy_set_tx_gain(pi, &target_gains); + wlc_lcnphy_set_tx_pwr_by_index(pi, 16); if (LCNREV_IS(pi->pubpi.phy_rev, 1) || pi_lcn->lcnphy_hw_iqcal_en) { @@ -3949,7 +3854,6 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) lcnphy_recal ? LCNPHY_CAL_RECAL : LCNPHY_CAL_FULL), false); } else { - wlc_lcnphy_set_tx_pwr_by_index(pi, 16); wlc_lcnphy_tx_iqlo_soft_cal_full(pi); } @@ -4374,22 +4278,17 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi, if (CHSPEC_IS5G(pi->radio_chanspec)) pa_gain = 0x70; else - pa_gain = 0x60; + pa_gain = 0x70; if (pi->sh->boardflags & BFL_FEM) pa_gain = 0x10; - tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; tab.tbl_len = 1; tab.tbl_ptr = &val; for (j = 0; j < 128; j++) { - if (pi->sh->boardflags & BFL_FEM) - gm_gain = gain_table[j].gm; - else - gm_gain = 15; - + gm_gain = gain_table[j].gm; val = (((u32) pa_gain << 24) | (gain_table[j].pad << 16) | (gain_table[j].pga << 8) | gm_gain); @@ -4600,10 +4499,7 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) write_phy_reg(pi, 0x4ea, 0x4688); - if (pi->sh->boardflags & BFL_FEM) - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); - else - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 3 << 0); + mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); mod_phy_reg(pi, 0x4eb, (0x7 << 6), 0 << 6); @@ -4614,13 +4510,6 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) wlc_lcnphy_rcal(pi); wlc_lcnphy_rc_cal(pi); - - if (!(pi->sh->boardflags & BFL_FEM)) { - write_radio_reg(pi, RADIO_2064_REG032, 0x6f); - write_radio_reg(pi, RADIO_2064_REG033, 0x19); - write_radio_reg(pi, RADIO_2064_REG039, 0xe); - } - } static void wlc_lcnphy_radio_init(struct brcms_phy *pi) @@ -4650,20 +4539,22 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi) wlc_lcnphy_write_table(pi, &tab); } - if (!(pi->sh->boardflags & BFL_FEM)) { - tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; - tab.tbl_width = 16; - tab.tbl_ptr = &val; - tab.tbl_len = 1; + tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; + tab.tbl_width = 16; + tab.tbl_ptr = &val; + tab.tbl_len = 1; - val = 150; - tab.tbl_offset = 0; - wlc_lcnphy_write_table(pi, &tab); + val = 114; + tab.tbl_offset = 0; + wlc_lcnphy_write_table(pi, &tab); - val = 220; - tab.tbl_offset = 1; - wlc_lcnphy_write_table(pi, &tab); - } + val = 130; + tab.tbl_offset = 1; + wlc_lcnphy_write_table(pi, &tab); + + val = 6; + tab.tbl_offset = 8; + wlc_lcnphy_write_table(pi, &tab); if (CHSPEC_IS2G(pi->radio_chanspec)) { if (pi->sh->boardflags & BFL_FEM) @@ -5055,7 +4946,6 @@ void wlc_phy_chanspec_set_lcnphy(struct brcms_phy *pi, u16 chanspec) wlc_lcnphy_load_tx_iir_filter(pi, true, 3); mod_phy_reg(pi, 0x4eb, (0x7 << 3), (1) << 3); - wlc_lcnphy_tssi_setup(pi); } void wlc_phy_detach_lcnphy(struct brcms_phy *pi) @@ -5094,7 +4984,8 @@ bool wlc_phy_attach_lcnphy(struct brcms_phy *pi) if (!wlc_phy_txpwr_srom_read_lcnphy(pi)) return false; - if (LCNREV_IS(pi->pubpi.phy_rev, 1)) { + if ((pi->sh->boardflags & BFL_FEM) && + (LCNREV_IS(pi->pubpi.phy_rev, 1))) { if (pi_lcn->lcnphy_tempsense_option == 3) { pi->hwpwrctrl = true; pi->hwpwrctrl_capable = true; diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c index b7e95acc2084..622c01ca72c5 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c @@ -1992,70 +1992,70 @@ static const u16 dot11lcn_sw_ctrl_tbl_4313_epa_rev0[] = { }; static const u16 dot11lcn_sw_ctrl_tbl_4313_rev0[] = { - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, }; static const u16 dot11lcn_sw_ctrl_tbl_rev0[] = { -- cgit v1.2.3 From e67dd874e60529dbd2e8232babb1e23479ba2ffa Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Tue, 19 Mar 2013 07:52:48 +0100 Subject: b43: N-PHY: increase initial value of "mind" in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit We're using "mind" variable to find the VCM that got the best polling results. For each VCM we calculte "currd" which is compared to the "mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a value smaller than 40 makes no sense, so increase the initial value. This fixes a regression introduced in 3.4 by commit: e0c9a0219a8f542e3946fe972a68aacf8c3f906c (my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s) Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index 3c35382ee6c2..e014a7a8154d 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1615,7 +1615,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) } for (i = 0; i < 4; i += 2) { s32 curr; - s32 mind = 40; + s32 mind = 0x100000; s32 minpoll = 249; u8 minvcm = 0; if (2 * core != i) @@ -1799,7 +1799,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) } for (i = 0; i < 4; i++) { - s32 mind = 40; + s32 mind = 0x100000; u8 minvcm = 0; s32 minpoll = 249; s32 curr; -- cgit v1.2.3 From b251412db99ccd4495ce372fec7daee27bf06923 Mon Sep 17 00:00:00 2001 From: "Iestyn C. Elfick" Date: Wed, 20 Mar 2013 14:02:31 -0500 Subject: b43: A fix for DMA transmission sequence errors Intermittently, b43 will report "Out of order TX status report on DMA ring". When this happens, the driver must be reset before communication can resume. The cause of the problem is believed to be an error in the closed-source firmware; however, all versions of the firmware are affected. This change uses the observation that the expected status is always 2 less than the observed value, and supplies a fake status report to skip one header/data pair. Not all devices suffer from this problem, but it can occur several times per second under heavy load. As each occurence kills the unmodified driver, this patch makes if possible for the affected devices to function. The patch logs only the first instance of the reset operation to prevent spamming the logs. Tested-by: Chris Vine Signed-off-by: Larry Finger Cc: Stable Signed-off-by: John W. Linville --- drivers/net/wireless/b43/dma.c | 65 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 53 insertions(+), 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c index 38bc5a7997ff..122146943bf2 100644 --- a/drivers/net/wireless/b43/dma.c +++ b/drivers/net/wireless/b43/dma.c @@ -1487,8 +1487,12 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, const struct b43_dma_ops *ops; struct b43_dmaring *ring; struct b43_dmadesc_meta *meta; + static const struct b43_txstatus fake; /* filled with 0 */ + const struct b43_txstatus *txstat; int slot, firstused; bool frame_succeed; + int skip; + static u8 err_out1, err_out2; ring = parse_cookie(dev, status->cookie, &slot); if (unlikely(!ring)) @@ -1501,13 +1505,36 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, firstused = ring->current_slot - ring->used_slots + 1; if (firstused < 0) firstused = ring->nr_slots + firstused; + + skip = 0; if (unlikely(slot != firstused)) { /* This possibly is a firmware bug and will result in - * malfunction, memory leaks and/or stall of DMA functionality. */ - b43dbg(dev->wl, "Out of order TX status report on DMA ring %d. " - "Expected %d, but got %d\n", - ring->index, firstused, slot); - return; + * malfunction, memory leaks and/or stall of DMA functionality. + */ + if (slot == next_slot(ring, next_slot(ring, firstused))) { + /* If a single header/data pair was missed, skip over + * the first two slots in an attempt to recover. + */ + slot = firstused; + skip = 2; + if (!err_out1) { + /* Report the error once. */ + b43dbg(dev->wl, + "Skip on DMA ring %d slot %d.\n", + ring->index, slot); + err_out1 = 1; + } + } else { + /* More than a single header/data pair were missed. + * Report this error once. + */ + if (!err_out2) + b43dbg(dev->wl, + "Out of order TX status report on DMA ring %d. Expected %d, but got %d\n", + ring->index, firstused, slot); + err_out2 = 1; + return; + } } ops = ring->ops; @@ -1522,11 +1549,13 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, slot, firstused, ring->index); break; } + if (meta->skb) { struct b43_private_tx_info *priv_info = - b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); + b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); - unmap_descbuffer(ring, meta->dmaaddr, meta->skb->len, 1); + unmap_descbuffer(ring, meta->dmaaddr, + meta->skb->len, 1); kfree(priv_info->bouncebuffer); priv_info->bouncebuffer = NULL; } else { @@ -1538,8 +1567,9 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, struct ieee80211_tx_info *info; if (unlikely(!meta->skb)) { - /* This is a scatter-gather fragment of a frame, so - * the skb pointer must not be NULL. */ + /* This is a scatter-gather fragment of a frame, + * so the skb pointer must not be NULL. + */ b43dbg(dev->wl, "TX status unexpected NULL skb " "at slot %d (first=%d) on ring %d\n", slot, firstused, ring->index); @@ -1550,9 +1580,18 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* * Call back to inform the ieee80211 subsystem about - * the status of the transmission. + * the status of the transmission. When skipping over + * a missed TX status report, use a status structure + * filled with zeros to indicate that the frame was not + * sent (frame_count 0) and not acknowledged */ - frame_succeed = b43_fill_txstatus_report(dev, info, status); + if (unlikely(skip)) + txstat = &fake; + else + txstat = status; + + frame_succeed = b43_fill_txstatus_report(dev, info, + txstat); #ifdef CONFIG_B43_DEBUG if (frame_succeed) ring->nr_succeed_tx_packets++; @@ -1580,12 +1619,14 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* Everything unmapped and free'd. So it's not used anymore. */ ring->used_slots--; - if (meta->is_last_fragment) { + if (meta->is_last_fragment && !skip) { /* This is the last scatter-gather * fragment of the frame. We are done. */ break; } slot = next_slot(ring, slot); + if (skip > 0) + --skip; } if (ring->stopped) { B43_WARN_ON(free_slots(ring) < TX_SLOTS_PER_FRAME); -- cgit v1.2.3 From 7fc0357479eeff4ca808c4d8c09bc7631f576b8d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 25 Mar 2013 11:27:46 -0700 Subject: ath9k: avoid queueing hw check work when suspended The following issue was reported. WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]() Hardware name: iMac12,1 queueing ieee80211 work while going to suspend Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1 Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] [] warn_slowpath_common+0x7f/0xc0 [] ? ath_start_rx_poll+0x70/0x70 [ath9k] ] warn_slowpath_fmt+0x46/0x50 [] ieee80211_can_queue_work.isra.7+0x32/0x40 Fix this by avoiding to queue the work if our device has already been marked as suspended or stopped. Reported-by: Parag Warudkar Tested-by: Parag Warudkar Cc: stable@vger.kernel.org Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/link.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/link.c b/drivers/net/wireless/ath/ath9k/link.c index 39c84ecf6a42..7fdac6c7b3ea 100644 --- a/drivers/net/wireless/ath/ath9k/link.c +++ b/drivers/net/wireless/ath/ath9k/link.c @@ -170,7 +170,8 @@ void ath_rx_poll(unsigned long data) { struct ath_softc *sc = (struct ath_softc *)data; - ieee80211_queue_work(sc->hw, &sc->hw_check_work); + if (!test_bit(SC_OP_INVALID, &sc->sc_flags)) + ieee80211_queue_work(sc->hw, &sc->hw_check_work); } /* -- cgit v1.2.3 From ace5af39866da7d45f43774150dace19a73716d6 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Tue, 26 Mar 2013 17:35:23 +0000 Subject: iwlegacy: 4965-rs: avoid null pointer dereference error il4965_rs_initialize_lq checks to see if sta is null, however, before that check il4965_rs_use_green dereferences sta when intializing use_green. Avoid a potential null pointer dereference error by only calling il4965_rs_use_green after we are sure sta is not null. Smatch analysis: drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn: variable dereferenced before check 'sta' (see line 2155) Signed-off-by: Colin Ian King Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/4965-rs.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlegacy/4965-rs.c b/drivers/net/wireless/iwlegacy/4965-rs.c index e8324b5e5bfe..6c7493c2d698 100644 --- a/drivers/net/wireless/iwlegacy/4965-rs.c +++ b/drivers/net/wireless/iwlegacy/4965-rs.c @@ -2152,7 +2152,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, int rate_idx; int i; u32 rate; - u8 use_green = il4965_rs_use_green(il, sta); + u8 use_green; u8 active_tbl = 0; u8 valid_tx_ant; struct il_station_priv *sta_priv; @@ -2160,6 +2160,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, if (!sta || !lq_sta) return; + use_green = il4965_rs_use_green(il, sta); sta_priv = (void *)sta->drv_priv; i = lq_sta->last_txrate_idx; -- cgit v1.2.3 From 2e1253d640eb7f8707d2591c93097c1e9f9c71d5 Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Wed, 27 Mar 2013 08:37:08 +0100 Subject: b43: N-PHY: use more bits for offset in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When calculating "offset" for final RSSI calibration we're using numbers bigger than s8 can hold. We have for example: offset[j] = 232 - poll_results[j]; formula. If poll_results[j] is small enough (it usually is) we treat number's bit as a sign bit. For example 232 - 1 becomes: 0xE8 - 0x1 = 0xE7, which is not 231 but -25. This code was introduced in e0c9a0219a8f542e3946fe972a68aacf8c3f906c and caused stability regression on some cards, for ex. BCM4322. Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index e014a7a8154d..e8486c1e091a 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1564,7 +1564,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) u16 clip_off[2] = { 0xFFFF, 0xFFFF }; u8 vcm_final = 0; - s8 offset[4]; + s32 offset[4]; s32 results[8][4] = { }; s32 results_min[4] = { }; s32 poll_results[4] = { }; @@ -1732,7 +1732,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) u8 regs_save_radio[2]; u16 regs_save_phy[2]; - s8 offset[4]; + s32 offset[4]; u8 core; u8 rail; -- cgit v1.2.3 From 14109a59caf93e6eae726a34bf2f0897508ec8c1 Mon Sep 17 00:00:00 2001 From: Frank Li Date: Tue, 26 Mar 2013 16:12:03 +0000 Subject: enet: fec: fix fail resume from suspend state Without this patch 1. boot with nfs (no_console_suspend) 2. echo mem >/sys/power/state 3. wakeup by wakesource 4. print "eth0: tx queue full" This fix above problem by reinit bd queue at restart function Signed-off-by: Frank Li Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec.c | 82 ++++++++++++++++++++++-------------- 1 file changed, 50 insertions(+), 32 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/freescale/fec.c b/drivers/net/ethernet/freescale/fec.c index 911d0253dbb2..f292c3aa423f 100644 --- a/drivers/net/ethernet/freescale/fec.c +++ b/drivers/net/ethernet/freescale/fec.c @@ -345,6 +345,53 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) return NETDEV_TX_OK; } +/* Init RX & TX buffer descriptors + */ +static void fec_enet_bd_init(struct net_device *dev) +{ + struct fec_enet_private *fep = netdev_priv(dev); + struct bufdesc *bdp; + unsigned int i; + + /* Initialize the receive buffer descriptors. */ + bdp = fep->rx_bd_base; + for (i = 0; i < RX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + if (bdp->cbd_bufaddr) + bdp->cbd_sc = BD_ENET_RX_EMPTY; + else + bdp->cbd_sc = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + + fep->cur_rx = fep->rx_bd_base; + + /* ...and the same for transmit */ + bdp = fep->tx_bd_base; + fep->cur_tx = bdp; + for (i = 0; i < TX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + bdp->cbd_sc = 0; + if (bdp->cbd_bufaddr && fep->tx_skbuff[i]) { + dev_kfree_skb_any(fep->tx_skbuff[i]); + fep->tx_skbuff[i] = NULL; + } + bdp->cbd_bufaddr = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + fep->dirty_tx = bdp; +} + /* This function is called to start or restart the FEC during a link * change. This only happens when switching between half and full * duplex. @@ -388,6 +435,8 @@ fec_restart(struct net_device *ndev, int duplex) /* Set maximum receive buffer size. */ writel(PKT_MAXBLR_SIZE, fep->hwp + FEC_R_BUFF_SIZE); + fec_enet_bd_init(ndev); + /* Set receive and transmit descriptor base. */ writel(fep->bd_dma, fep->hwp + FEC_R_DES_START); if (fep->bufdesc_ex) @@ -397,7 +446,6 @@ fec_restart(struct net_device *ndev, int duplex) writel((unsigned long)fep->bd_dma + sizeof(struct bufdesc) * RX_RING_SIZE, fep->hwp + FEC_X_DES_START); - fep->cur_rx = fep->rx_bd_base; for (i = 0; i <= TX_RING_MOD_MASK; i++) { if (fep->tx_skbuff[i]) { @@ -1597,8 +1645,6 @@ static int fec_enet_init(struct net_device *ndev) { struct fec_enet_private *fep = netdev_priv(ndev); struct bufdesc *cbd_base; - struct bufdesc *bdp; - unsigned int i; /* Allocate memory for buffer descriptors. */ cbd_base = dma_alloc_coherent(NULL, PAGE_SIZE, &fep->bd_dma, @@ -1608,6 +1654,7 @@ static int fec_enet_init(struct net_device *ndev) return -ENOMEM; } + memset(cbd_base, 0, PAGE_SIZE); spin_lock_init(&fep->hw_lock); fep->netdev = ndev; @@ -1631,35 +1678,6 @@ static int fec_enet_init(struct net_device *ndev) writel(FEC_RX_DISABLED_IMASK, fep->hwp + FEC_IMASK); netif_napi_add(ndev, &fep->napi, fec_enet_rx_napi, FEC_NAPI_WEIGHT); - /* Initialize the receive buffer descriptors. */ - bdp = fep->rx_bd_base; - for (i = 0; i < RX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - - /* ...and the same for transmit */ - bdp = fep->tx_bd_base; - fep->cur_tx = bdp; - for (i = 0; i < TX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp->cbd_bufaddr = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - fep->dirty_tx = bdp; - fec_restart(ndev, 0); return 0; -- cgit v1.2.3 From b56d6b3fca6d1214dbc9c5655f26e5d4ec04afc8 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:41:59 +0000 Subject: drivers: net: ethernet: cpsw: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index df32a090d08e..80cad06e5eb2 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -436,7 +436,7 @@ void cpsw_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); cpts_tx_timestamp(priv->cpts, skb); priv->stats.tx_packets++; priv->stats.tx_bytes += len; -- cgit v1.2.3 From 7e51cde276ca820d526c6c21cf8147df595a36bf Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:42:00 +0000 Subject: drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/davinci_emac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c index ae1b77aa199f..72300bc9e378 100644 --- a/drivers/net/ethernet/ti/davinci_emac.c +++ b/drivers/net/ethernet/ti/davinci_emac.c @@ -1053,7 +1053,7 @@ static void emac_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); ndev->stats.tx_packets++; ndev->stats.tx_bytes += len; dev_kfree_skb_any(skb); -- cgit v1.2.3 From 715230a44310a8cf66fbfb5a46f9a62a9b2de424 Mon Sep 17 00:00:00 2001 From: Kees Cook Date: Wed, 27 Mar 2013 06:40:50 +0000 Subject: tg3: fix length overflow in VPD firmware parsing Commit 184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version when present") introduced VPD parsing that contained a potential length overflow. Limit the hardware's reported firmware string length (max 255 bytes) to stay inside the driver's firmware string length (32 bytes). On overflow, truncate the formatted firmware string instead of potentially overwriting portions of the tg3 struct. http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf Signed-off-by: Kees Cook Reported-by: Oded Horovitz Reported-by: Brad Spengler Cc: stable@vger.kernel.org Cc: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 67d2663b3974..17a972734ba7 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -14604,8 +14604,11 @@ static void tg3_read_vpd(struct tg3 *tp) if (j + len > block_end) goto partno; - memcpy(tp->fw_ver, &vpd_data[j], len); - strncat(tp->fw_ver, " bc ", vpdlen - len - 1); + if (len >= sizeof(tp->fw_ver)) + len = sizeof(tp->fw_ver) - 1; + memset(tp->fw_ver, 0, sizeof(tp->fw_ver)); + snprintf(tp->fw_ver, sizeof(tp->fw_ver), "%.*s bc ", len, + &vpd_data[j]); } partno: -- cgit v1.2.3 From b8730b403aee94db4631bfefb546a6ce8c287dc2 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 27 Mar 2013 20:49:58 +0100 Subject: iwlwifi: dvm: fix the passive-no-RX workaround Alex Romosan reported that since the mac80211 changes in "mac80211: start auth/assoc timeout on frame status" and the subsequent fixes in "mac80211: fix auth/assoc timeout handling" (commits 1672c0e31917 and 89afe614c0c) there's sometimes an issue connecting to a 5 GHz network with the iwlwifi DVM driver. The reason appears to be that since these commits any bad TX status makes mac80211 immediately try again, causing all of the authentication attempts to be quickly rejected by the firmware as it hasn't heard a beacon yet. Before, it would wait for the timeout regardless of status. To fix this, invoke the passive-no-RX workaround when not associated yet as well. This will cause the first frame to get lost, but then the driver will stop the queues and the second attempt will only be transmitted after hearing a beacon, thus delaying it appropriately to not make the firmware reject it again. Reported-by: Alex Romosan Tested-by: Alex Romosan Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/dvm/rxon.c | 18 ++++++++---------- drivers/net/wireless/iwlwifi/dvm/tx.c | 2 +- 2 files changed, 9 insertions(+), 11 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/dvm/rxon.c b/drivers/net/wireless/iwlwifi/dvm/rxon.c index 23be948cf162..a82b6b39d4ff 100644 --- a/drivers/net/wireless/iwlwifi/dvm/rxon.c +++ b/drivers/net/wireless/iwlwifi/dvm/rxon.c @@ -1419,6 +1419,14 @@ void iwlagn_bss_info_changed(struct ieee80211_hw *hw, mutex_lock(&priv->mutex); + if (changes & BSS_CHANGED_IDLE && bss_conf->idle) { + /* + * If we go idle, then clearly no "passive-no-rx" + * workaround is needed any more, this is a reset. + */ + iwlagn_lift_passive_no_rx(priv); + } + if (unlikely(!iwl_is_ready(priv))) { IWL_DEBUG_MAC80211(priv, "leave - not ready\n"); mutex_unlock(&priv->mutex); @@ -1450,16 +1458,6 @@ void iwlagn_bss_info_changed(struct ieee80211_hw *hw, priv->timestamp = bss_conf->sync_tsf; ctx->staging.filter_flags |= RXON_FILTER_ASSOC_MSK; } else { - /* - * If we disassociate while there are pending - * frames, just wake up the queues and let the - * frames "escape" ... This shouldn't really - * be happening to start with, but we should - * not get stuck in this case either since it - * can happen if userspace gets confused. - */ - iwlagn_lift_passive_no_rx(priv); - ctx->staging.filter_flags &= ~RXON_FILTER_ASSOC_MSK; if (ctx->ctxid == IWL_RXON_CTX_BSS) diff --git a/drivers/net/wireless/iwlwifi/dvm/tx.c b/drivers/net/wireless/iwlwifi/dvm/tx.c index 6aec2df3bb27..d1a670d7b10c 100644 --- a/drivers/net/wireless/iwlwifi/dvm/tx.c +++ b/drivers/net/wireless/iwlwifi/dvm/tx.c @@ -1192,7 +1192,7 @@ int iwlagn_rx_reply_tx(struct iwl_priv *priv, struct iwl_rx_cmd_buffer *rxb, memset(&info->status, 0, sizeof(info->status)); if (status == TX_STATUS_FAIL_PASSIVE_NO_RX && - iwl_is_associated_ctx(ctx) && ctx->vif && + ctx->vif && ctx->vif->type == NL80211_IFTYPE_STATION) { /* block and stop all queues */ priv->passive_no_rx = true; -- cgit v1.2.3 From 9cfe8b156c21cf340b3a10ecb3022fbbc1c39185 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:35 +0000 Subject: sky2: Receive Overflows not counted The sky2 driver doesn't count the Receive Overflows because the MAC interrupt for this event is not set in the MAC's interrupt mask. The MAC's interrupt mask is set only for Transmit FIFO Underruns. Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) Otherwise the Receive Overflow event will not generate any interrupt. The Receive Overflow interrupt is handled correctly Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.h b/drivers/net/ethernet/marvell/sky2.h index 615ac63ea860..ec6dcd80152b 100644 --- a/drivers/net/ethernet/marvell/sky2.h +++ b/drivers/net/ethernet/marvell/sky2.h @@ -2074,7 +2074,7 @@ enum { GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ -#define GMAC_DEF_MSK GM_IS_TX_FF_UR +#define GMAC_DEF_MSK (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) }; /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ -- cgit v1.2.3 From 74f9f42c1c1650e74fb464f76644c9041f996851 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:42 +0000 Subject: sky2: Threshold for Pause Packet is set wrong The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a wrong value which leads to only 2kB of RAM remaining space. This can lead to Rx overflow errors even with activated flow-control. Fix: We should increase the value to 8192/8 Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c index fc07ca35721b..6a0e671fcecd 100644 --- a/drivers/net/ethernet/marvell/sky2.c +++ b/drivers/net/ethernet/marvell/sky2.c @@ -1067,7 +1067,7 @@ static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); - tp = space - 2048/8; + tp = space - 8192/8; sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); } else { -- cgit v1.2.3 From 1bc7db16782c2a581fb4d53ca853631050f31611 Mon Sep 17 00:00:00 2001 From: "nikolay@redhat.com" Date: Wed, 27 Mar 2013 03:32:41 +0000 Subject: bonding: fix disabling of arp_interval and miimon Currently if either arp_interval or miimon is disabled, they both get disabled, and upon disabling they get executed once more which is not the proper behaviour. Also when doing a no-op and disabling an already disabled one, the other again gets disabled. Also fix the error messages with the proper valid ranges, and a small typo fix in the up delay error message (outputting "down delay", instead of "up delay"). Signed-off-by: Nikolay Aleksandrov Signed-off-by: David S. Miller --- drivers/net/bonding/bond_sysfs.c | 92 +++++++++++++++++++++------------------- 1 file changed, 48 insertions(+), 44 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index db103e03ba05..ea7a388f4843 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -527,7 +527,7 @@ static ssize_t bonding_store_arp_interval(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid arp_interval value %d not in range 1-%d; rejected.\n", + pr_err("%s: Invalid arp_interval value %d not in range 0-%d; rejected.\n", bond->dev->name, new_value, INT_MAX); ret = -EINVAL; goto out; @@ -542,14 +542,15 @@ static ssize_t bonding_store_arp_interval(struct device *d, pr_info("%s: Setting ARP monitoring interval to %d.\n", bond->dev->name, new_value); bond->params.arp_interval = new_value; - if (bond->params.miimon) { - pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", - bond->dev->name, bond->dev->name); - bond->params.miimon = 0; - } - if (!bond->params.arp_targets[0]) { - pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", - bond->dev->name); + if (new_value) { + if (bond->params.miimon) { + pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", + bond->dev->name, bond->dev->name); + bond->params.miimon = 0; + } + if (!bond->params.arp_targets[0]) + pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", + bond->dev->name); } if (bond->dev->flags & IFF_UP) { /* If the interface is up, we may need to fire off @@ -557,10 +558,13 @@ static ssize_t bonding_store_arp_interval(struct device *d, * timer will get fired off when the open function * is called. */ - cancel_delayed_work_sync(&bond->mii_work); - queue_delayed_work(bond->wq, &bond->arp_work, 0); + if (!new_value) { + cancel_delayed_work_sync(&bond->arp_work); + } else { + cancel_delayed_work_sync(&bond->mii_work); + queue_delayed_work(bond->wq, &bond->arp_work, 0); + } } - out: rtnl_unlock(); return ret; @@ -702,7 +706,7 @@ static ssize_t bonding_store_downdelay(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -757,8 +761,8 @@ static ssize_t bonding_store_updelay(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + pr_err("%s: Invalid up delay value %d not in range %d-%d; rejected.\n", + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -968,37 +972,37 @@ static ssize_t bonding_store_miimon(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid miimon value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; - } else { - pr_info("%s: Setting MII monitoring interval to %d.\n", - bond->dev->name, new_value); - bond->params.miimon = new_value; - if (bond->params.updelay) - pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.updelay * bond->params.miimon); - if (bond->params.downdelay) - pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.downdelay * bond->params.miimon); - if (bond->params.arp_interval) { - pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", - bond->dev->name); - bond->params.arp_interval = 0; - if (bond->params.arp_validate) { - bond->params.arp_validate = - BOND_ARP_VALIDATE_NONE; - } - } - - if (bond->dev->flags & IFF_UP) { - /* If the interface is up, we may need to fire off - * the MII timer. If the interface is down, the - * timer will get fired off when the open function - * is called. - */ + } + pr_info("%s: Setting MII monitoring interval to %d.\n", + bond->dev->name, new_value); + bond->params.miimon = new_value; + if (bond->params.updelay) + pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.updelay * bond->params.miimon); + if (bond->params.downdelay) + pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.downdelay * bond->params.miimon); + if (new_value && bond->params.arp_interval) { + pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", + bond->dev->name); + bond->params.arp_interval = 0; + if (bond->params.arp_validate) + bond->params.arp_validate = BOND_ARP_VALIDATE_NONE; + } + if (bond->dev->flags & IFF_UP) { + /* If the interface is up, we may need to fire off + * the MII timer. If the interface is down, the + * timer will get fired off when the open function + * is called. + */ + if (!new_value) { + cancel_delayed_work_sync(&bond->mii_work); + } else { cancel_delayed_work_sync(&bond->arp_work); queue_delayed_work(bond->wq, &bond->mii_work, 0); } -- cgit v1.2.3 From 4c51e53689569398d656e631c17308d9b8e84650 Mon Sep 17 00:00:00 2001 From: Steve Glendinning Date: Thu, 28 Mar 2013 02:34:41 +0000 Subject: smsc75xx: fix jumbo frame support This patch enables RX of jumbo frames for LAN7500. Previously the driver would transmit jumbo frames succesfully but would drop received jumbo frames (incrementing the interface errors count). With this patch applied the device can succesfully receive jumbo frames up to MTU 9000 (9014 bytes on the wire including ethernet header). Signed-off-by: Steve Glendinning Signed-off-by: David S. Miller --- drivers/net/usb/smsc75xx.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/usb/smsc75xx.c b/drivers/net/usb/smsc75xx.c index 9abe51710f22..1a15ec14c386 100644 --- a/drivers/net/usb/smsc75xx.c +++ b/drivers/net/usb/smsc75xx.c @@ -914,8 +914,12 @@ static int smsc75xx_set_rx_max_frame_length(struct usbnet *dev, int size) static int smsc75xx_change_mtu(struct net_device *netdev, int new_mtu) { struct usbnet *dev = netdev_priv(netdev); + int ret; + + if (new_mtu > MAX_SINGLE_PACKET_SIZE) + return -EINVAL; - int ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu); + ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set mac rx frame length\n"); return ret; @@ -1324,7 +1328,7 @@ static int smsc75xx_reset(struct usbnet *dev) netif_dbg(dev, ifup, dev->net, "FCT_TX_CTL set to 0x%08x\n", buf); - ret = smsc75xx_set_rx_max_frame_length(dev, 1514); + ret = smsc75xx_set_rx_max_frame_length(dev, dev->net->mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set max rx frame length\n"); return ret; @@ -2134,8 +2138,8 @@ static int smsc75xx_rx_fixup(struct usbnet *dev, struct sk_buff *skb) else if (rx_cmd_a & (RX_CMD_A_LONG | RX_CMD_A_RUNT)) dev->net->stats.rx_frame_errors++; } else { - /* ETH_FRAME_LEN + 4(CRC) + 2(COE) + 4(Vlan) */ - if (unlikely(size > (ETH_FRAME_LEN + 12))) { + /* MAX_SINGLE_PACKET_SIZE + 4(CRC) + 2(COE) + 4(Vlan) */ + if (unlikely(size > (MAX_SINGLE_PACKET_SIZE + ETH_HLEN + 12))) { netif_dbg(dev, rx_err, dev->net, "size err rx_cmd_a=0x%08x\n", rx_cmd_a); -- cgit v1.2.3 From dc574f1d52d893f516f3786ff7635450bac00eef Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:44 +0000 Subject: net: calxedaxgmac: fix rx ring handling when OOM If skb allocation for the rx ring fails repeatedly, we can reach a point were the ring is empty. In this condition, the driver is out of sync with the h/w. While this has always been possible, the removal of the skb recycling seems to have made triggering this problem easier. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index a170065b5973..bb1e80bfa78a 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -1141,6 +1141,9 @@ static int xgmac_rx(struct xgmac_priv *priv, int limit) struct sk_buff *skb; int frame_len; + if (!dma_ring_cnt(priv->rx_head, priv->rx_tail, DMA_RX_RING_SZ)) + break; + entry = priv->rx_tail; p = priv->dma_rx + entry; if (desc_get_owner(p)) -- cgit v1.2.3 From e6c3827dcfe53dd78b824d2ee4007a216ada739e Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:45 +0000 Subject: net: calxedaxgmac: Wake-on-LAN fixes WOL is broken because the magic packet status bit is getting set rather than the enable bit. The PMT interrupt is not getting serviced because the PMT interrupt is also enabled on the global interrupt, but not cleared by the global interrupt and the global interrupt is higher priority. This fixes both of these issues to get WOL working. There's still a problem with receive after resume, but at least now we can wake-up. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index bb1e80bfa78a..b0ebc9f6d55e 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -163,6 +163,7 @@ #define XGMAC_FLOW_CTRL_FCB_BPA 0x00000001 /* Flow Control Busy ... */ /* XGMAC_INT_STAT reg */ +#define XGMAC_INT_STAT_PMTIM 0x00800000 /* PMT Interrupt Mask */ #define XGMAC_INT_STAT_PMT 0x0080 /* PMT Interrupt Status */ #define XGMAC_INT_STAT_LPI 0x0040 /* LPI Interrupt Status */ @@ -960,6 +961,9 @@ static int xgmac_hw_init(struct net_device *dev) writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_STATUS); writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_INTR_ENA); + /* Mask power mgt interrupt */ + writel(XGMAC_INT_STAT_PMTIM, ioaddr + XGMAC_INT_STAT); + /* XGMAC requires AXI bus init. This is a 'magic number' for now */ writel(0x0077000E, ioaddr + XGMAC_DMA_AXI_BUS); @@ -1828,7 +1832,7 @@ static void xgmac_pmt(void __iomem *ioaddr, unsigned long mode) unsigned int pmt = 0; if (mode & WAKE_MAGIC) - pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT; + pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT_EN; if (mode & WAKE_UCAST) pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_GLBL_UNICAST; -- cgit v1.2.3 From 188ab1b105c96656f6bcfb49d0d8bb1b1936b632 Mon Sep 17 00:00:00 2001 From: Hannes Frederic Sowa Date: Thu, 28 Mar 2013 18:10:50 +0000 Subject: atl1e: drop pci-msi support because of packet corruption MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Usage of pci-msi results in corrupted dma packet transfers to the host. Reported-by: rebelyouth Cc: Huang, Xiong Tested-by: Christian Sünkenberg Signed-off-by: Hannes Frederic Sowa Signed-off-by: David S. Miller --- drivers/net/ethernet/atheros/atl1e/atl1e.h | 1 - drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 19 ++----------------- 2 files changed, 2 insertions(+), 18 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e.h b/drivers/net/ethernet/atheros/atl1e/atl1e.h index 829b5ad71d0d..edfdf6b950e7 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e.h +++ b/drivers/net/ethernet/atheros/atl1e/atl1e.h @@ -438,7 +438,6 @@ struct atl1e_adapter { struct atl1e_hw hw; struct atl1e_hw_stats hw_stats; - bool have_msi; u32 wol; u16 link_speed; u16 link_duplex; diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c index 92f4734f860d..f73d5609439a 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c +++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c @@ -1849,34 +1849,19 @@ static void atl1e_free_irq(struct atl1e_adapter *adapter) struct net_device *netdev = adapter->netdev; free_irq(adapter->pdev->irq, netdev); - - if (adapter->have_msi) - pci_disable_msi(adapter->pdev); } static int atl1e_request_irq(struct atl1e_adapter *adapter) { struct pci_dev *pdev = adapter->pdev; struct net_device *netdev = adapter->netdev; - int flags = 0; int err = 0; - adapter->have_msi = true; - err = pci_enable_msi(pdev); - if (err) { - netdev_dbg(netdev, - "Unable to allocate MSI interrupt Error: %d\n", err); - adapter->have_msi = false; - } - - if (!adapter->have_msi) - flags |= IRQF_SHARED; - err = request_irq(pdev->irq, atl1e_intr, flags, netdev->name, netdev); + err = request_irq(pdev->irq, atl1e_intr, IRQF_SHARED, netdev->name, + netdev); if (err) { netdev_dbg(adapter->netdev, "Unable to allocate interrupt Error: %d\n", err); - if (adapter->have_msi) - pci_disable_msi(pdev); return err; } netdev_dbg(netdev, "atl1e_request_irq OK\n"); -- cgit v1.2.3 From 14bc435ea54cb888409efb54fc6b76c13ef530e9 Mon Sep 17 00:00:00 2001 From: "Max.Nekludov@us.elster.com" Date: Fri, 29 Mar 2013 05:27:36 +0000 Subject: ks8851: Fix interpretation of rxlen field. According to the Datasheet (page 52): 15-12 Reserved 11-0 RXBC Receive Byte Count This field indicates the present received frame byte size. The code has a bug: rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied Signed-off-by: Max Nekludov Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ks8851.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c index 33bcb63d56a2..8fb481252e2c 100644 --- a/drivers/net/ethernet/micrel/ks8851.c +++ b/drivers/net/ethernet/micrel/ks8851.c @@ -528,7 +528,7 @@ static void ks8851_rx_pkts(struct ks8851_net *ks) for (; rxfc != 0; rxfc--) { rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; - rxlen = rxh >> 16; + rxlen = (rxh >> 16) & 0xfff; netif_dbg(ks, rx_status, ks->netdev, "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen); -- cgit v1.2.3 From 1e1b812bbe1069fc8e2e372dca7d5f541c7a8ceb Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:50:07 +0000 Subject: sh_eth: fix handling of no LINK signal The code handling the absent LINK signal (or the absent PSR register -- which reflects the state of this signal) is quite naive and has probably never really worked. It's probably enough to say that this code is executed only on the LINK change interrupt (sic!) but even if we actually have the signal and choose to ignore it (it might be connected to PHY's link/activity LED output as on the Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update 'mdp->link' gets executed later than the LINK change interrupt where it is checked, and so RX/TX never get enabled via ECMR register. So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen not to be used) or PSR register is absent, and enable/disable RX/TX directly in sh_eth_adjust_link() in this case. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index bf5e3cf97c4d..1ca8b2b10adc 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1216,10 +1216,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) if (felic_stat & ECSR_LCHNG) { /* Link Changed */ if (mdp->cd->no_psr || mdp->no_ether_link) { - if (mdp->link == PHY_DOWN) - link_stat = 0; - else - link_stat = PHY_ST_LINK; + goto ignore_link; } else { link_stat = (sh_eth_read(ndev, PSR)); if (mdp->ether_link_active_low) @@ -1242,6 +1239,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) } } +ignore_link: if (intr_status & EESR_TWB) { /* Write buck end. unused write back interrupt */ if (intr_status & EESR_TABT) /* Transmit Abort int */ @@ -1392,12 +1390,16 @@ static void sh_eth_adjust_link(struct net_device *ndev) (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; mdp->link = phydev->link; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_enable(ndev); } } else if (mdp->link) { new_state = 1; mdp->link = PHY_DOWN; mdp->speed = 0; mdp->duplex = -1; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_disable(ndev); } if (new_state && netif_msg_link(mdp)) -- cgit v1.2.3 From 3893b27345ac0ff13c1b9ec20ad50966b810997e Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:54:20 +0000 Subject: sh_eth: workaround for spurious ECI interrupt At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its mask in EESIPR register. I can 100% reproduce it with the following scenario: target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device but doesn't get a proper reply and then succeeds with on-board SMC chip; then I login and try to bring up the SoC Ether device with 'ifconfig', and I get an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt mask in EESIPR register is all 0), if that interrupt is accompanied by a pending EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx() because sh_eth_ring_init() hasn't been called yet! The solution I worked out is the following: in sh_eth_interrupt(), mask the interrupt status from EESR register with the interrupt mask from EESIPR register in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit in this mask set because we always need to fully handle EESR.ECI interrupt in sh_eth_error() in order to quench it (as it doesn't get cleared by just writing 1 to the this bit as all the other interrupts). While at it, remove unneeded initializer for 'intr_status' variable and give it *unsigned long* type, matching the type of sh_eth_read()'s result; fix comment. Signed-off-by: Sergei Shtylyov Reviewed-by: Max Filippov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 1ca8b2b10adc..44f7904e5054 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1324,12 +1324,18 @@ static irqreturn_t sh_eth_interrupt(int irq, void *netdev) struct sh_eth_private *mdp = netdev_priv(ndev); struct sh_eth_cpu_data *cd = mdp->cd; irqreturn_t ret = IRQ_NONE; - u32 intr_status = 0; + unsigned long intr_status; spin_lock(&mdp->lock); - /* Get interrpt stat */ + /* Get interrupt status */ intr_status = sh_eth_read(ndev, EESR); + /* Mask it with the interrupt mask, forcing ECI interrupt to be always + * enabled since it's the one that comes thru regardless of the mask, + * and we need to fully handle it in sh_eth_error() in order to quench + * it as it doesn't get cleared by just writing 1 to the ECI bit... + */ + intr_status &= sh_eth_read(ndev, EESIPR) | DMAC_M_ECI; /* Clear interrupt */ if (intr_status & (EESR_FRC | EESR_RMAF | EESR_RRF | EESR_RTLF | EESR_RTSF | EESR_PRE | EESR_CERF | -- cgit v1.2.3 From 3340d2aae3433ad9147f6bf0adc452b324e31591 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 10:11:04 +0000 Subject: sh_eth: make 'link' field of 'struct sh_eth_private' *int* The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the 'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and the former field gets assigned from the latter. Make the field match, getting rid of incorrectly used PHY_DOWN value in assignments/comparisons. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 8 ++++---- drivers/net/ethernet/renesas/sh_eth.h | 2 +- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 44f7904e5054..6ed333fe5c04 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1377,7 +1377,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) struct phy_device *phydev = mdp->phydev; int new_state = 0; - if (phydev->link != PHY_DOWN) { + if (phydev->link) { if (phydev->duplex != mdp->duplex) { new_state = 1; mdp->duplex = phydev->duplex; @@ -1391,7 +1391,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) if (mdp->cd->set_rate) mdp->cd->set_rate(ndev); } - if (mdp->link == PHY_DOWN) { + if (!mdp->link) { sh_eth_write(ndev, (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; @@ -1401,7 +1401,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) } } else if (mdp->link) { new_state = 1; - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; if (mdp->cd->no_psr || mdp->no_ether_link) @@ -1422,7 +1422,7 @@ static int sh_eth_phy_init(struct net_device *ndev) snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, mdp->mii_bus->id , mdp->phy_id); - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index e6655678458e..828be4515008 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -723,7 +723,7 @@ struct sh_eth_private { u32 phy_id; /* PHY ID */ struct mii_bus *mii_bus; /* MDIO bus control */ struct phy_device *phydev; /* PHY device control */ - enum phy_state link; + int link; phy_interface_t phy_interface; int msg_enable; int speed; -- cgit v1.2.3 From 6741f40d198c6a5feb23653a1efd4ca47f93d83d Mon Sep 17 00:00:00 2001 From: Joseph CHANG Date: Thu, 28 Mar 2013 23:13:42 +0000 Subject: DM9000B: driver initialization upgrade Fix bug for DM9000 revision B which contain a DSP PHY DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY, So need extra change in initialization, For explicity PHY Reset and PHY init parameter, and first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe(). Following DM9000_NCR reset cause by dm9000_open() clear the NCR_MAC_LBK bit. Without this fix, Power-up FIFO pointers error happen around 2% rate among Davicom's customers' boards. With this fix, All above cases can be solved. Signed-off-by: Joseph CHANG Signed-off-by: David S. Miller --- drivers/net/ethernet/davicom/dm9000.c | 214 +++++++++++++++++----------------- drivers/net/ethernet/davicom/dm9000.h | 11 +- 2 files changed, 120 insertions(+), 105 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index 8cdf02503d13..9eada8e86078 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -257,6 +257,107 @@ static void dm9000_dumpblk_32bit(void __iomem *reg, int count) tmp = readl(reg); } +/* + * Sleep, either by using msleep() or if we are suspending, then + * use mdelay() to sleep. + */ +static void dm9000_msleep(board_info_t *db, unsigned int ms) +{ + if (db->in_suspend) + mdelay(ms); + else + msleep(ms); +} + +/* Read a word from phyxcer */ +static int +dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned int reg_save; + int ret; + + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Issue phyxcer read command */ + iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait read complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ + + /* The read data keeps on REG_0D & REG_0E */ + ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + mutex_unlock(&db->addr_lock); + + dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); + return ret; +} + +/* Write a word to phyxcer */ +static void +dm9000_phy_write(struct net_device *dev, + int phyaddr_unused, int reg, int value) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned long reg_save; + + dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Fill the written data into REG_0D & REG_0E */ + iow(db, DM9000_EPDRL, value); + iow(db, DM9000_EPDRH, value >> 8); + + /* Issue phyxcer write command */ + iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait write complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + + spin_unlock_irqrestore(&db->lock, flags); + mutex_unlock(&db->addr_lock); +} + /* dm9000_set_io * * select the specified set of io routines to use with the @@ -795,6 +896,9 @@ dm9000_init_dm9000(struct net_device *dev) iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */ + dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */ + dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); /* Init */ + ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; /* if wol is needed, then always set NCR_WAKEEN otherwise we end @@ -1201,109 +1305,6 @@ dm9000_open(struct net_device *dev) return 0; } -/* - * Sleep, either by using msleep() or if we are suspending, then - * use mdelay() to sleep. - */ -static void dm9000_msleep(board_info_t *db, unsigned int ms) -{ - if (db->in_suspend) - mdelay(ms); - else - msleep(ms); -} - -/* - * Read a word from phyxcer - */ -static int -dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned int reg_save; - int ret; - - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); /* Issue phyxcer read command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - dm9000_msleep(db, 1); /* Wait read complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ - - /* The read data keeps on REG_0D & REG_0E */ - ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - mutex_unlock(&db->addr_lock); - - dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); - return ret; -} - -/* - * Write a word to phyxcer - */ -static void -dm9000_phy_write(struct net_device *dev, - int phyaddr_unused, int reg, int value) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned long reg_save; - - dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - /* Fill the written data into REG_0D & REG_0E */ - iow(db, DM9000_EPDRL, value); - iow(db, DM9000_EPDRH, value >> 8); - - iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); /* Issue phyxcer write command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock, flags); - - dm9000_msleep(db, 1); /* Wait write complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - - spin_unlock_irqrestore(&db->lock, flags); - mutex_unlock(&db->addr_lock); -} - static void dm9000_shutdown(struct net_device *dev) { @@ -1502,7 +1503,12 @@ dm9000_probe(struct platform_device *pdev) db->flags |= DM9000_PLATF_SIMPLE_PHY; #endif - dm9000_reset(db); + /* Fixing bug on dm9000_probe, takeover dm9000_reset(db), + * Need 'NCR_MAC_LBK' bit to indeed stable our DM9000 fifo + * while probe stage. + */ + + iow(db, DM9000_NCR, NCR_MAC_LBK | NCR_RST); /* try multiple times, DM9000 sometimes gets the read wrong */ for (i = 0; i < 8; i++) { diff --git a/drivers/net/ethernet/davicom/dm9000.h b/drivers/net/ethernet/davicom/dm9000.h index 55688bd1a3ef..9ce058adabab 100644 --- a/drivers/net/ethernet/davicom/dm9000.h +++ b/drivers/net/ethernet/davicom/dm9000.h @@ -69,7 +69,9 @@ #define NCR_WAKEEN (1<<6) #define NCR_FCOL (1<<4) #define NCR_FDX (1<<3) -#define NCR_LBK (3<<1) + +#define NCR_RESERVED (3<<1) +#define NCR_MAC_LBK (1<<1) #define NCR_RST (1<<0) #define NSR_SPEED (1<<7) @@ -167,5 +169,12 @@ #define ISR_LNKCHNG (1<<5) #define ISR_UNDERRUN (1<<4) +/* Davicom MII registers. + */ + +#define MII_DM_DSPCR 0x1b /* DSP Control Register */ + +#define DSPCR_INIT_PARAM 0xE100 /* DSP init parameter */ + #endif /* _DM9000X_H_ */ -- cgit v1.2.3 From 901ceba4e81e9dd6b4a3c4c37ee22000a6c5c65f Mon Sep 17 00:00:00 2001 From: Stone Piao Date: Fri, 29 Mar 2013 19:21:21 -0700 Subject: mwifiex: limit channel number not to overflow memory Limit the channel number in scan request, or the driver scan config structure memory will be overflowed. Cc: # 3.5+ Signed-off-by: Stone Piao Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/cfg80211.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/cfg80211.c b/drivers/net/wireless/mwifiex/cfg80211.c index a44023a7bd57..8aaf56ade4d9 100644 --- a/drivers/net/wireless/mwifiex/cfg80211.c +++ b/drivers/net/wireless/mwifiex/cfg80211.c @@ -1892,7 +1892,8 @@ mwifiex_cfg80211_scan(struct wiphy *wiphy, } } - for (i = 0; i < request->n_channels; i++) { + for (i = 0; i < min_t(u32, request->n_channels, + MWIFIEX_USER_SCAN_CHAN_MAX); i++) { chan = request->channels[i]; priv->user_scan_cfg->chan_list[i].chan_number = chan->hw_value; priv->user_scan_cfg->chan_list[i].radio_type = chan->band; -- cgit v1.2.3 From fcd99434fb5c137274d2e15dd2a6a7455f0f29ff Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Tue, 2 Apr 2013 05:15:16 +0000 Subject: bonding: get netdev_rx_handler_unregister out of locks Now that netdev_rx_handler_unregister contains synchronize_net(), we need to call it outside of bond->lock, cause it might sleep. Also, remove the already unneded synchronize_net(). Signed-off-by: Veaceslav Falico Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 6bbd90e1123c..a51241b2e621 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1976,12 +1976,11 @@ static int __bond_release_one(struct net_device *bond_dev, return -EINVAL; } + write_unlock_bh(&bond->lock); /* unregister rx_handler early so bond_handle_frame wouldn't be called * for this slave anymore. */ netdev_rx_handler_unregister(slave_dev); - write_unlock_bh(&bond->lock); - synchronize_net(); write_lock_bh(&bond->lock); if (!all && !bond->params.fail_over_mac) { -- cgit v1.2.3 From bab6a9eac05360db25c81b0090f6b1195dd986cc Mon Sep 17 00:00:00 2001 From: Yan Burman Date: Tue, 2 Apr 2013 16:49:45 +0300 Subject: net/mlx4_en: Fix setting initial MAC address Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression under which the MAC address read from the card was not converted correctly (the most significant byte was not handled), fix that. Reviewed-by: Or Gerlitz Signed-off-by: Yan Burman Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index f278b10ef714..30d78f806dc3 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -411,8 +411,8 @@ static int mlx4_en_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid) static void mlx4_en_u64_to_mac(unsigned char dst_mac[ETH_ALEN + 2], u64 src_mac) { - unsigned int i; - for (i = ETH_ALEN - 1; i; --i) { + int i; + for (i = ETH_ALEN - 1; i >= 0; --i) { dst_mac[i] = src_mac & 0xff; src_mac >>= 8; } -- cgit v1.2.3 From 21de979ecfc7b7f9442f8aea9a54b3ab670d0151 Mon Sep 17 00:00:00 2001 From: Bing Zhao Date: Mon, 1 Apr 2013 12:44:45 -0700 Subject: mwifiex: complete last internal scan We are waiting on first scan command of internal scan request before association, so we should complete on last internal scan command response. Cc: # 3.8 Tested-by: Daniel Drake Tested-by: Marco Cesarano Signed-off-by: Bing Zhao Signed-off-by: Amitkumar Karwar Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/scan.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/scan.c b/drivers/net/wireless/mwifiex/scan.c index d215b4d3c51b..e7f6deaf715e 100644 --- a/drivers/net/wireless/mwifiex/scan.c +++ b/drivers/net/wireless/mwifiex/scan.c @@ -1393,8 +1393,10 @@ int mwifiex_scan_networks(struct mwifiex_private *priv, queue_work(adapter->workqueue, &adapter->main_work); /* Perform internal scan synchronously */ - if (!priv->scan_request) + if (!priv->scan_request) { + dev_dbg(adapter->dev, "wait internal scan\n"); mwifiex_wait_queue_complete(adapter, cmd_node); + } } else { spin_unlock_irqrestore(&adapter->scan_pending_q_lock, flags); @@ -1793,7 +1795,12 @@ check_next_scan: /* Need to indicate IOCTL complete */ if (adapter->curr_cmd->wait_q_enabled) { adapter->cmd_wait_q.status = 0; - mwifiex_complete_cmd(adapter, adapter->curr_cmd); + if (!priv->scan_request) { + dev_dbg(adapter->dev, + "complete internal scan\n"); + mwifiex_complete_cmd(adapter, + adapter->curr_cmd); + } } if (priv->report_scan_result) priv->report_scan_result = false; -- cgit v1.2.3 From 992f6068f09b3d711ffe247701287a2ee87842cb Mon Sep 17 00:00:00 2001 From: Hante Meuleman Date: Tue, 2 Apr 2013 21:06:17 +0200 Subject: brcmfmac: fix tkip mic tx/rx ap swap bug. tx and rx michael tkip keys are always swapped in case being configured per mac. This is wrong for AP. The swap should only be done for STA mode. Reviewed-by: Arend Van Spriel Reviewed-by: Pieter-Paul Giesberts Reviewed-by: Piotr Haber Signed-off-by: Hante Meuleman Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c index 2af9c0f0798d..3bc47eaf167a 100644 --- a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +++ b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c @@ -1891,8 +1891,10 @@ static s32 brcmf_add_keyext(struct wiphy *wiphy, struct net_device *ndev, u8 key_idx, const u8 *mac_addr, struct key_params *params) { + struct brcmf_if *ifp = netdev_priv(ndev); struct brcmf_wsec_key key; s32 err = 0; + u8 keybuf[8]; memset(&key, 0, sizeof(key)); key.index = (u32) key_idx; @@ -1916,8 +1918,9 @@ brcmf_add_keyext(struct wiphy *wiphy, struct net_device *ndev, brcmf_dbg(CONN, "Setting the key index %d\n", key.index); memcpy(key.data, params->key, key.len); - if (params->cipher == WLAN_CIPHER_SUITE_TKIP) { - u8 keybuf[8]; + if ((ifp->vif->mode != WL_MODE_AP) && + (params->cipher == WLAN_CIPHER_SUITE_TKIP)) { + brcmf_dbg(CONN, "Swapping RX/TX MIC key\n"); memcpy(keybuf, &key.data[24], sizeof(keybuf)); memcpy(&key.data[24], &key.data[16], sizeof(keybuf)); memcpy(&key.data[16], keybuf, sizeof(keybuf)); @@ -2013,7 +2016,7 @@ brcmf_cfg80211_add_key(struct wiphy *wiphy, struct net_device *ndev, break; case WLAN_CIPHER_SUITE_TKIP: if (ifp->vif->mode != WL_MODE_AP) { - brcmf_dbg(CONN, "Swapping key\n"); + brcmf_dbg(CONN, "Swapping RX/TX MIC key\n"); memcpy(keybuf, &key.data[24], sizeof(keybuf)); memcpy(&key.data[24], &key.data[16], sizeof(keybuf)); memcpy(&key.data[16], keybuf, sizeof(keybuf)); -- cgit v1.2.3 From 5c33a9420499e384a5b7c2262b17fd608ec76472 Mon Sep 17 00:00:00 2001 From: Hante Meuleman Date: Tue, 2 Apr 2013 21:06:18 +0200 Subject: brcmfmac: fix stopping AP. on stop_ap the dongle was not properly shutdown. As a result it was not possible to restart AP or STA after AP operation without restarting the device. This patch will fix that. Reviewed-by: Arend Van Spriel Reviewed-by: Pieter-Paul Giesberts Reviewed-by: Piotr Haber Signed-off-by: Hante Meuleman Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 25 +++++++++++++--------- 1 file changed, 15 insertions(+), 10 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c index 3bc47eaf167a..b9dbf2c0f63c 100644 --- a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +++ b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c @@ -3827,8 +3827,9 @@ exit: static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) { struct brcmf_if *ifp = netdev_priv(ndev); - s32 err = -EPERM; + s32 err; struct brcmf_fil_bss_enable_le bss_enable; + struct brcmf_join_params join_params; brcmf_dbg(TRACE, "Enter\n"); @@ -3836,16 +3837,21 @@ static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) /* Due to most likely deauths outstanding we sleep */ /* first to make sure they get processed by fw. */ msleep(400); - err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_AP, 0); - if (err < 0) { - brcmf_err("setting AP mode failed %d\n", err); - goto exit; - } + + memset(&join_params, 0, sizeof(join_params)); + err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SET_SSID, + &join_params, sizeof(join_params)); + if (err < 0) + brcmf_err("SET SSID error (%d)\n", err); err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_UP, 0); - if (err < 0) { + if (err < 0) brcmf_err("BRCMF_C_UP error %d\n", err); - goto exit; - } + err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_AP, 0); + if (err < 0) + brcmf_err("setting AP mode failed %d\n", err); + err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_INFRA, 0); + if (err < 0) + brcmf_err("setting INFRA mode failed %d\n", err); } else { bss_enable.bsscfg_idx = cpu_to_le32(ifp->bssidx); bss_enable.enable = cpu_to_le32(0); @@ -3858,7 +3864,6 @@ static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) set_bit(BRCMF_VIF_STATUS_AP_CREATING, &ifp->vif->sme_state); clear_bit(BRCMF_VIF_STATUS_AP_CREATED, &ifp->vif->sme_state); -exit: return err; } -- cgit v1.2.3 From c5bf53a826d22c284e6e1d309d32c388684e26a7 Mon Sep 17 00:00:00 2001 From: Hante Meuleman Date: Tue, 2 Apr 2013 21:06:19 +0200 Subject: brcmfmac: fix returning cipher_suite for get_key operation. When multiple cipher suites have been programmed then the lowest suite is to be retured. This fixes issue when AP mode is using CCMP and TKIP WPA combination where rekeying will fail. Reviewed-by: Arend Van Spriel Reviewed-by: Pieter-Paul Giesberts Reviewed-by: Piotr Haber Signed-off-by: Hante Meuleman Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c index b9dbf2c0f63c..ec46ffff5409 100644 --- a/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +++ b/drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c @@ -2121,8 +2121,7 @@ brcmf_cfg80211_get_key(struct wiphy *wiphy, struct net_device *ndev, err = -EAGAIN; goto done; } - switch (wsec & ~SES_OW_ENABLED) { - case WEP_ENABLED: + if (wsec & WEP_ENABLED) { sec = &profile->sec; if (sec->cipher_pairwise & WLAN_CIPHER_SUITE_WEP40) { params.cipher = WLAN_CIPHER_SUITE_WEP40; @@ -2131,16 +2130,13 @@ brcmf_cfg80211_get_key(struct wiphy *wiphy, struct net_device *ndev, params.cipher = WLAN_CIPHER_SUITE_WEP104; brcmf_dbg(CONN, "WLAN_CIPHER_SUITE_WEP104\n"); } - break; - case TKIP_ENABLED: + } else if (wsec & TKIP_ENABLED) { params.cipher = WLAN_CIPHER_SUITE_TKIP; brcmf_dbg(CONN, "WLAN_CIPHER_SUITE_TKIP\n"); - break; - case AES_ENABLED: + } else if (wsec & AES_ENABLED) { params.cipher = WLAN_CIPHER_SUITE_AES_CMAC; brcmf_dbg(CONN, "WLAN_CIPHER_SUITE_AES_CMAC\n"); - break; - default: + } else { brcmf_err("Invalid algo (0x%x)\n", wsec); err = -EINVAL; goto done; -- cgit v1.2.3 From 3eaa956c5b18b9c955ae5a4e6e6909cae23f38e0 Mon Sep 17 00:00:00 2001 From: Franky Lin Date: Tue, 2 Apr 2013 21:06:20 +0200 Subject: brcmfmac: do not proceed if fail to download nvram to dongle Nvram contains critical initialization parameter for firmware to run. Host driver should not proceed if nvram fails to be downloaded to dongle. Reviewed-by: Piotr Haber Reviewed-by: Arend van Spriel Reviewed-by: Pieter-Paul Giesberts Signed-off-by: Franky Lin Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c index 4469321c0eb3..35fc68be158d 100644 --- a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c @@ -3317,15 +3317,15 @@ static int _brcmf_sdbrcm_download_firmware(struct brcmf_sdio *bus) goto err; } - /* External image takes precedence if specified */ if (brcmf_sdbrcm_download_code_file(bus)) { brcmf_err("dongle image file download failed\n"); goto err; } - /* External nvram takes precedence if specified */ - if (brcmf_sdbrcm_download_nvram(bus)) + if (brcmf_sdbrcm_download_nvram(bus)) { brcmf_err("dongle nvram file download failed\n"); + goto err; + } /* Take arm out of reset */ if (brcmf_sdbrcm_download_state(bus, false)) { -- cgit v1.2.3 From f50b1cd37446ad32c432f0f73bbed67a1c076eae Mon Sep 17 00:00:00 2001 From: Robert Shade Date: Tue, 2 Apr 2013 19:52:45 -0400 Subject: ath9k: Re-enable interrupts after a channel change failure ath_complete_reset will not be called if ath9k_hw_reset is unsuccessful, so we need to re-enable intertupts to balence the previous ath_prepare_reset call. Also schedule a reset as a best effort method to recover the chip from whatever state caused the channel change failure. Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771 Signed-off-by: Robert Shade Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 6e66f9c6782b..988372d218a4 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -280,6 +280,10 @@ static int ath_reset_internal(struct ath_softc *sc, struct ath9k_channel *hchan) if (r) { ath_err(common, "Unable to reset channel, reset status %d\n", r); + + ath9k_hw_enable_interrupts(ah); + ath9k_queue_reset(sc, RESET_TYPE_BB_HANG); + goto out; } -- cgit v1.2.3 From 83589b30f1e1dc9898986293c9336b8ce1705dec Mon Sep 17 00:00:00 2001 From: Tim Gardner Date: Mon, 18 Feb 2013 12:56:28 -0700 Subject: rt2x00: rt2x00pci_regbusy_read() - only print register access failure once BugLink: http://bugs.launchpad.net/bugs/1128840 It appears that when this register read fails it never recovers, so I think there is no need to repeat the same error message ad infinitum. Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: "John W. Linville" Cc: linux-wireless@vger.kernel.org Cc: users@rt2x00.serialmonkey.com Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Tim Gardner Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2x00pci.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/rt2x00/rt2x00pci.c b/drivers/net/wireless/rt2x00/rt2x00pci.c index a0c8caef3b0a..b1c673ecada1 100644 --- a/drivers/net/wireless/rt2x00/rt2x00pci.c +++ b/drivers/net/wireless/rt2x00/rt2x00pci.c @@ -52,8 +52,8 @@ int rt2x00pci_regbusy_read(struct rt2x00_dev *rt2x00dev, udelay(REGISTER_BUSY_DELAY); } - ERROR(rt2x00dev, "Indirect register access failed: " - "offset=0x%.08x, value=0x%.08x\n", offset, *reg); + printk_once(KERN_ERR "%s() Indirect register access failed: " + "offset=0x%.08x, value=0x%.08x\n", __func__, offset, *reg); *reg = ~0; return 0; -- cgit v1.2.3 From 69a2bac8984c4e6dba78b330ed183fd580c65e99 Mon Sep 17 00:00:00 2001 From: Gabor Juhos Date: Fri, 29 Mar 2013 15:52:27 +0100 Subject: rt2x00: rt2x00pci: fix build error on Ralink RT3x5x SoCs The rt2800pci driver supports the built-in wireless MAC of the Ralink RT3x5x SoCs. However building the driver for these SoCs leads to the following error: LD init/built-in.o drivers/built-in.o: In function `rt2800pci_rxdone_tasklet': <...>/drivers/net/wireless/rt2x00/rt2800pci.c:1012: undefined reference to `rt2x00pci_rxdone' drivers/built-in.o:(.rodata+0x4780): undefined reference to `rt2x00pci_initialize' drivers/built-in.o:(.rodata+0x4784): undefined reference to `rt2x00pci_uninitialize' drivers/built-in.o:(.rodata+0x47bc): undefined reference to `rt2x00pci_flush_queue' drivers/built-in.o:(.rodata+0x4818): undefined reference to `rt2x00pci_regbusy_read' make[5]: *** [vmlinux] Error 1 The missing functions are provided by the rt2x00pci module. This module is only selected by the rt2800pci driver if PCI support is enabled in the kernel, because some parts of the rt2x00pci code depends on PCI support. PCI support is not available on the RT3x5x SoCs because those have no PCI host controller at all. Move the non PCI specific code from rt2x00pci into a separate module. This makes it possible to use that code even if PCI support is disabled. The affected functions are used by all of the rt2x00 PCI drivers so select the new module for those drivers. Signed-off-by: Gabor Juhos Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/Kconfig | 7 + drivers/net/wireless/rt2x00/Makefile | 1 + drivers/net/wireless/rt2x00/rt2400pci.c | 1 + drivers/net/wireless/rt2x00/rt2500pci.c | 1 + drivers/net/wireless/rt2x00/rt2800pci.c | 1 + drivers/net/wireless/rt2x00/rt2x00mmio.c | 216 +++++++++++++++++++++++++++++++ drivers/net/wireless/rt2x00/rt2x00mmio.h | 119 +++++++++++++++++ drivers/net/wireless/rt2x00/rt2x00pci.c | 176 ------------------------- drivers/net/wireless/rt2x00/rt2x00pci.h | 88 ------------- drivers/net/wireless/rt2x00/rt61pci.c | 1 + 10 files changed, 347 insertions(+), 264 deletions(-) create mode 100644 drivers/net/wireless/rt2x00/rt2x00mmio.c create mode 100644 drivers/net/wireless/rt2x00/rt2x00mmio.h (limited to 'drivers/net') diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig index 2bf4efa33186..76cd47eb901e 100644 --- a/drivers/net/wireless/rt2x00/Kconfig +++ b/drivers/net/wireless/rt2x00/Kconfig @@ -20,6 +20,7 @@ if RT2X00 config RT2400PCI tristate "Ralink rt2400 (PCI/PCMCIA) support" depends on PCI + select RT2X00_LIB_MMIO select RT2X00_LIB_PCI select EEPROM_93CX6 ---help--- @@ -31,6 +32,7 @@ config RT2400PCI config RT2500PCI tristate "Ralink rt2500 (PCI/PCMCIA) support" depends on PCI + select RT2X00_LIB_MMIO select RT2X00_LIB_PCI select EEPROM_93CX6 ---help--- @@ -43,6 +45,7 @@ config RT61PCI tristate "Ralink rt2501/rt61 (PCI/PCMCIA) support" depends on PCI select RT2X00_LIB_PCI + select RT2X00_LIB_MMIO select RT2X00_LIB_FIRMWARE select RT2X00_LIB_CRYPTO select CRC_ITU_T @@ -57,6 +60,7 @@ config RT2800PCI tristate "Ralink rt27xx/rt28xx/rt30xx (PCI/PCIe/PCMCIA) support" depends on PCI || SOC_RT288X || SOC_RT305X select RT2800_LIB + select RT2X00_LIB_MMIO select RT2X00_LIB_PCI if PCI select RT2X00_LIB_SOC if SOC_RT288X || SOC_RT305X select RT2X00_LIB_FIRMWARE @@ -185,6 +189,9 @@ endif config RT2800_LIB tristate +config RT2X00_LIB_MMIO + tristate + config RT2X00_LIB_PCI tristate select RT2X00_LIB diff --git a/drivers/net/wireless/rt2x00/Makefile b/drivers/net/wireless/rt2x00/Makefile index 349d5b8284a4..f069d8bc5b67 100644 --- a/drivers/net/wireless/rt2x00/Makefile +++ b/drivers/net/wireless/rt2x00/Makefile @@ -9,6 +9,7 @@ rt2x00lib-$(CONFIG_RT2X00_LIB_FIRMWARE) += rt2x00firmware.o rt2x00lib-$(CONFIG_RT2X00_LIB_LEDS) += rt2x00leds.o obj-$(CONFIG_RT2X00_LIB) += rt2x00lib.o +obj-$(CONFIG_RT2X00_LIB_MMIO) += rt2x00mmio.o obj-$(CONFIG_RT2X00_LIB_PCI) += rt2x00pci.o obj-$(CONFIG_RT2X00_LIB_SOC) += rt2x00soc.o obj-$(CONFIG_RT2X00_LIB_USB) += rt2x00usb.o diff --git a/drivers/net/wireless/rt2x00/rt2400pci.c b/drivers/net/wireless/rt2x00/rt2400pci.c index 221beaaa83f1..dcfb54e0c516 100644 --- a/drivers/net/wireless/rt2x00/rt2400pci.c +++ b/drivers/net/wireless/rt2x00/rt2400pci.c @@ -34,6 +34,7 @@ #include #include "rt2x00.h" +#include "rt2x00mmio.h" #include "rt2x00pci.h" #include "rt2400pci.h" diff --git a/drivers/net/wireless/rt2x00/rt2500pci.c b/drivers/net/wireless/rt2x00/rt2500pci.c index 39edc59e8d03..e1d2dc9ed28a 100644 --- a/drivers/net/wireless/rt2x00/rt2500pci.c +++ b/drivers/net/wireless/rt2x00/rt2500pci.c @@ -34,6 +34,7 @@ #include #include "rt2x00.h" +#include "rt2x00mmio.h" #include "rt2x00pci.h" #include "rt2500pci.h" diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c index ded73da4de0b..ba5a05625aaa 100644 --- a/drivers/net/wireless/rt2x00/rt2800pci.c +++ b/drivers/net/wireless/rt2x00/rt2800pci.c @@ -41,6 +41,7 @@ #include #include "rt2x00.h" +#include "rt2x00mmio.h" #include "rt2x00pci.h" #include "rt2x00soc.h" #include "rt2800lib.h" diff --git a/drivers/net/wireless/rt2x00/rt2x00mmio.c b/drivers/net/wireless/rt2x00/rt2x00mmio.c new file mode 100644 index 000000000000..d84a680ba0c9 --- /dev/null +++ b/drivers/net/wireless/rt2x00/rt2x00mmio.c @@ -0,0 +1,216 @@ +/* + Copyright (C) 2004 - 2009 Ivo van Doorn + + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +/* + Module: rt2x00mmio + Abstract: rt2x00 generic mmio device routines. + */ + +#include +#include +#include +#include + +#include "rt2x00.h" +#include "rt2x00mmio.h" + +/* + * Register access. + */ +int rt2x00pci_regbusy_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const struct rt2x00_field32 field, + u32 *reg) +{ + unsigned int i; + + if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) + return 0; + + for (i = 0; i < REGISTER_BUSY_COUNT; i++) { + rt2x00pci_register_read(rt2x00dev, offset, reg); + if (!rt2x00_get_field32(*reg, field)) + return 1; + udelay(REGISTER_BUSY_DELAY); + } + + printk_once(KERN_ERR "%s() Indirect register access failed: " + "offset=0x%.08x, value=0x%.08x\n", __func__, offset, *reg); + *reg = ~0; + + return 0; +} +EXPORT_SYMBOL_GPL(rt2x00pci_regbusy_read); + +bool rt2x00pci_rxdone(struct rt2x00_dev *rt2x00dev) +{ + struct data_queue *queue = rt2x00dev->rx; + struct queue_entry *entry; + struct queue_entry_priv_pci *entry_priv; + struct skb_frame_desc *skbdesc; + int max_rx = 16; + + while (--max_rx) { + entry = rt2x00queue_get_entry(queue, Q_INDEX); + entry_priv = entry->priv_data; + + if (rt2x00dev->ops->lib->get_entry_state(entry)) + break; + + /* + * Fill in desc fields of the skb descriptor + */ + skbdesc = get_skb_frame_desc(entry->skb); + skbdesc->desc = entry_priv->desc; + skbdesc->desc_len = entry->queue->desc_size; + + /* + * DMA is already done, notify rt2x00lib that + * it finished successfully. + */ + rt2x00lib_dmastart(entry); + rt2x00lib_dmadone(entry); + + /* + * Send the frame to rt2x00lib for further processing. + */ + rt2x00lib_rxdone(entry, GFP_ATOMIC); + } + + return !max_rx; +} +EXPORT_SYMBOL_GPL(rt2x00pci_rxdone); + +void rt2x00pci_flush_queue(struct data_queue *queue, bool drop) +{ + unsigned int i; + + for (i = 0; !rt2x00queue_empty(queue) && i < 10; i++) + msleep(10); +} +EXPORT_SYMBOL_GPL(rt2x00pci_flush_queue); + +/* + * Device initialization handlers. + */ +static int rt2x00pci_alloc_queue_dma(struct rt2x00_dev *rt2x00dev, + struct data_queue *queue) +{ + struct queue_entry_priv_pci *entry_priv; + void *addr; + dma_addr_t dma; + unsigned int i; + + /* + * Allocate DMA memory for descriptor and buffer. + */ + addr = dma_alloc_coherent(rt2x00dev->dev, + queue->limit * queue->desc_size, + &dma, GFP_KERNEL); + if (!addr) + return -ENOMEM; + + memset(addr, 0, queue->limit * queue->desc_size); + + /* + * Initialize all queue entries to contain valid addresses. + */ + for (i = 0; i < queue->limit; i++) { + entry_priv = queue->entries[i].priv_data; + entry_priv->desc = addr + i * queue->desc_size; + entry_priv->desc_dma = dma + i * queue->desc_size; + } + + return 0; +} + +static void rt2x00pci_free_queue_dma(struct rt2x00_dev *rt2x00dev, + struct data_queue *queue) +{ + struct queue_entry_priv_pci *entry_priv = + queue->entries[0].priv_data; + + if (entry_priv->desc) + dma_free_coherent(rt2x00dev->dev, + queue->limit * queue->desc_size, + entry_priv->desc, entry_priv->desc_dma); + entry_priv->desc = NULL; +} + +int rt2x00pci_initialize(struct rt2x00_dev *rt2x00dev) +{ + struct data_queue *queue; + int status; + + /* + * Allocate DMA + */ + queue_for_each(rt2x00dev, queue) { + status = rt2x00pci_alloc_queue_dma(rt2x00dev, queue); + if (status) + goto exit; + } + + /* + * Register interrupt handler. + */ + status = request_irq(rt2x00dev->irq, + rt2x00dev->ops->lib->irq_handler, + IRQF_SHARED, rt2x00dev->name, rt2x00dev); + if (status) { + ERROR(rt2x00dev, "IRQ %d allocation failed (error %d).\n", + rt2x00dev->irq, status); + goto exit; + } + + return 0; + +exit: + queue_for_each(rt2x00dev, queue) + rt2x00pci_free_queue_dma(rt2x00dev, queue); + + return status; +} +EXPORT_SYMBOL_GPL(rt2x00pci_initialize); + +void rt2x00pci_uninitialize(struct rt2x00_dev *rt2x00dev) +{ + struct data_queue *queue; + + /* + * Free irq line. + */ + free_irq(rt2x00dev->irq, rt2x00dev); + + /* + * Free DMA + */ + queue_for_each(rt2x00dev, queue) + rt2x00pci_free_queue_dma(rt2x00dev, queue); +} +EXPORT_SYMBOL_GPL(rt2x00pci_uninitialize); + +/* + * rt2x00mmio module information. + */ +MODULE_AUTHOR(DRV_PROJECT); +MODULE_VERSION(DRV_VERSION); +MODULE_DESCRIPTION("rt2x00 mmio library"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/wireless/rt2x00/rt2x00mmio.h b/drivers/net/wireless/rt2x00/rt2x00mmio.h new file mode 100644 index 000000000000..4ecaf60175bf --- /dev/null +++ b/drivers/net/wireless/rt2x00/rt2x00mmio.h @@ -0,0 +1,119 @@ +/* + Copyright (C) 2004 - 2009 Ivo van Doorn + + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the + Free Software Foundation, Inc., + 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +/* + Module: rt2x00mmio + Abstract: Data structures for the rt2x00mmio module. + */ + +#ifndef RT2X00MMIO_H +#define RT2X00MMIO_H + +#include + +/* + * Register access. + */ +static inline void rt2x00pci_register_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 *value) +{ + *value = readl(rt2x00dev->csr.base + offset); +} + +static inline void rt2x00pci_register_multiread(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + void *value, const u32 length) +{ + memcpy_fromio(value, rt2x00dev->csr.base + offset, length); +} + +static inline void rt2x00pci_register_write(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 value) +{ + writel(value, rt2x00dev->csr.base + offset); +} + +static inline void rt2x00pci_register_multiwrite(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const void *value, + const u32 length) +{ + __iowrite32_copy(rt2x00dev->csr.base + offset, value, length >> 2); +} + +/** + * rt2x00pci_regbusy_read - Read from register with busy check + * @rt2x00dev: Device pointer, see &struct rt2x00_dev. + * @offset: Register offset + * @field: Field to check if register is busy + * @reg: Pointer to where register contents should be stored + * + * This function will read the given register, and checks if the + * register is busy. If it is, it will sleep for a couple of + * microseconds before reading the register again. If the register + * is not read after a certain timeout, this function will return + * FALSE. + */ +int rt2x00pci_regbusy_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + const struct rt2x00_field32 field, + u32 *reg); + +/** + * struct queue_entry_priv_pci: Per entry PCI specific information + * + * @desc: Pointer to device descriptor + * @desc_dma: DMA pointer to &desc. + * @data: Pointer to device's entry memory. + * @data_dma: DMA pointer to &data. + */ +struct queue_entry_priv_pci { + __le32 *desc; + dma_addr_t desc_dma; +}; + +/** + * rt2x00pci_rxdone - Handle RX done events + * @rt2x00dev: Device pointer, see &struct rt2x00_dev. + * + * Returns true if there are still rx frames pending and false if all + * pending rx frames were processed. + */ +bool rt2x00pci_rxdone(struct rt2x00_dev *rt2x00dev); + +/** + * rt2x00pci_flush_queue - Flush data queue + * @queue: Data queue to stop + * @drop: True to drop all pending frames. + * + * This will wait for a maximum of 100ms, waiting for the queues + * to become empty. + */ +void rt2x00pci_flush_queue(struct data_queue *queue, bool drop); + +/* + * Device initialization handlers. + */ +int rt2x00pci_initialize(struct rt2x00_dev *rt2x00dev); +void rt2x00pci_uninitialize(struct rt2x00_dev *rt2x00dev); + +#endif /* RT2X00MMIO_H */ diff --git a/drivers/net/wireless/rt2x00/rt2x00pci.c b/drivers/net/wireless/rt2x00/rt2x00pci.c index b1c673ecada1..e87865e33113 100644 --- a/drivers/net/wireless/rt2x00/rt2x00pci.c +++ b/drivers/net/wireless/rt2x00/rt2x00pci.c @@ -32,182 +32,6 @@ #include "rt2x00.h" #include "rt2x00pci.h" -/* - * Register access. - */ -int rt2x00pci_regbusy_read(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - const struct rt2x00_field32 field, - u32 *reg) -{ - unsigned int i; - - if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) - return 0; - - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2x00pci_register_read(rt2x00dev, offset, reg); - if (!rt2x00_get_field32(*reg, field)) - return 1; - udelay(REGISTER_BUSY_DELAY); - } - - printk_once(KERN_ERR "%s() Indirect register access failed: " - "offset=0x%.08x, value=0x%.08x\n", __func__, offset, *reg); - *reg = ~0; - - return 0; -} -EXPORT_SYMBOL_GPL(rt2x00pci_regbusy_read); - -bool rt2x00pci_rxdone(struct rt2x00_dev *rt2x00dev) -{ - struct data_queue *queue = rt2x00dev->rx; - struct queue_entry *entry; - struct queue_entry_priv_pci *entry_priv; - struct skb_frame_desc *skbdesc; - int max_rx = 16; - - while (--max_rx) { - entry = rt2x00queue_get_entry(queue, Q_INDEX); - entry_priv = entry->priv_data; - - if (rt2x00dev->ops->lib->get_entry_state(entry)) - break; - - /* - * Fill in desc fields of the skb descriptor - */ - skbdesc = get_skb_frame_desc(entry->skb); - skbdesc->desc = entry_priv->desc; - skbdesc->desc_len = entry->queue->desc_size; - - /* - * DMA is already done, notify rt2x00lib that - * it finished successfully. - */ - rt2x00lib_dmastart(entry); - rt2x00lib_dmadone(entry); - - /* - * Send the frame to rt2x00lib for further processing. - */ - rt2x00lib_rxdone(entry, GFP_ATOMIC); - } - - return !max_rx; -} -EXPORT_SYMBOL_GPL(rt2x00pci_rxdone); - -void rt2x00pci_flush_queue(struct data_queue *queue, bool drop) -{ - unsigned int i; - - for (i = 0; !rt2x00queue_empty(queue) && i < 10; i++) - msleep(10); -} -EXPORT_SYMBOL_GPL(rt2x00pci_flush_queue); - -/* - * Device initialization handlers. - */ -static int rt2x00pci_alloc_queue_dma(struct rt2x00_dev *rt2x00dev, - struct data_queue *queue) -{ - struct queue_entry_priv_pci *entry_priv; - void *addr; - dma_addr_t dma; - unsigned int i; - - /* - * Allocate DMA memory for descriptor and buffer. - */ - addr = dma_alloc_coherent(rt2x00dev->dev, - queue->limit * queue->desc_size, - &dma, GFP_KERNEL); - if (!addr) - return -ENOMEM; - - memset(addr, 0, queue->limit * queue->desc_size); - - /* - * Initialize all queue entries to contain valid addresses. - */ - for (i = 0; i < queue->limit; i++) { - entry_priv = queue->entries[i].priv_data; - entry_priv->desc = addr + i * queue->desc_size; - entry_priv->desc_dma = dma + i * queue->desc_size; - } - - return 0; -} - -static void rt2x00pci_free_queue_dma(struct rt2x00_dev *rt2x00dev, - struct data_queue *queue) -{ - struct queue_entry_priv_pci *entry_priv = - queue->entries[0].priv_data; - - if (entry_priv->desc) - dma_free_coherent(rt2x00dev->dev, - queue->limit * queue->desc_size, - entry_priv->desc, entry_priv->desc_dma); - entry_priv->desc = NULL; -} - -int rt2x00pci_initialize(struct rt2x00_dev *rt2x00dev) -{ - struct data_queue *queue; - int status; - - /* - * Allocate DMA - */ - queue_for_each(rt2x00dev, queue) { - status = rt2x00pci_alloc_queue_dma(rt2x00dev, queue); - if (status) - goto exit; - } - - /* - * Register interrupt handler. - */ - status = request_irq(rt2x00dev->irq, - rt2x00dev->ops->lib->irq_handler, - IRQF_SHARED, rt2x00dev->name, rt2x00dev); - if (status) { - ERROR(rt2x00dev, "IRQ %d allocation failed (error %d).\n", - rt2x00dev->irq, status); - goto exit; - } - - return 0; - -exit: - queue_for_each(rt2x00dev, queue) - rt2x00pci_free_queue_dma(rt2x00dev, queue); - - return status; -} -EXPORT_SYMBOL_GPL(rt2x00pci_initialize); - -void rt2x00pci_uninitialize(struct rt2x00_dev *rt2x00dev) -{ - struct data_queue *queue; - - /* - * Free irq line. - */ - free_irq(rt2x00dev->irq, rt2x00dev); - - /* - * Free DMA - */ - queue_for_each(rt2x00dev, queue) - rt2x00pci_free_queue_dma(rt2x00dev, queue); -} -EXPORT_SYMBOL_GPL(rt2x00pci_uninitialize); - /* * PCI driver handlers. */ diff --git a/drivers/net/wireless/rt2x00/rt2x00pci.h b/drivers/net/wireless/rt2x00/rt2x00pci.h index e2c99f2b9a14..60d90b20f8b9 100644 --- a/drivers/net/wireless/rt2x00/rt2x00pci.h +++ b/drivers/net/wireless/rt2x00/rt2x00pci.h @@ -35,94 +35,6 @@ */ #define PCI_DEVICE_DATA(__ops) .driver_data = (kernel_ulong_t)(__ops) -/* - * Register access. - */ -static inline void rt2x00pci_register_read(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - u32 *value) -{ - *value = readl(rt2x00dev->csr.base + offset); -} - -static inline void rt2x00pci_register_multiread(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - void *value, const u32 length) -{ - memcpy_fromio(value, rt2x00dev->csr.base + offset, length); -} - -static inline void rt2x00pci_register_write(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - u32 value) -{ - writel(value, rt2x00dev->csr.base + offset); -} - -static inline void rt2x00pci_register_multiwrite(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - const void *value, - const u32 length) -{ - __iowrite32_copy(rt2x00dev->csr.base + offset, value, length >> 2); -} - -/** - * rt2x00pci_regbusy_read - Read from register with busy check - * @rt2x00dev: Device pointer, see &struct rt2x00_dev. - * @offset: Register offset - * @field: Field to check if register is busy - * @reg: Pointer to where register contents should be stored - * - * This function will read the given register, and checks if the - * register is busy. If it is, it will sleep for a couple of - * microseconds before reading the register again. If the register - * is not read after a certain timeout, this function will return - * FALSE. - */ -int rt2x00pci_regbusy_read(struct rt2x00_dev *rt2x00dev, - const unsigned int offset, - const struct rt2x00_field32 field, - u32 *reg); - -/** - * struct queue_entry_priv_pci: Per entry PCI specific information - * - * @desc: Pointer to device descriptor - * @desc_dma: DMA pointer to &desc. - * @data: Pointer to device's entry memory. - * @data_dma: DMA pointer to &data. - */ -struct queue_entry_priv_pci { - __le32 *desc; - dma_addr_t desc_dma; -}; - -/** - * rt2x00pci_rxdone - Handle RX done events - * @rt2x00dev: Device pointer, see &struct rt2x00_dev. - * - * Returns true if there are still rx frames pending and false if all - * pending rx frames were processed. - */ -bool rt2x00pci_rxdone(struct rt2x00_dev *rt2x00dev); - -/** - * rt2x00pci_flush_queue - Flush data queue - * @queue: Data queue to stop - * @drop: True to drop all pending frames. - * - * This will wait for a maximum of 100ms, waiting for the queues - * to become empty. - */ -void rt2x00pci_flush_queue(struct data_queue *queue, bool drop); - -/* - * Device initialization handlers. - */ -int rt2x00pci_initialize(struct rt2x00_dev *rt2x00dev); -void rt2x00pci_uninitialize(struct rt2x00_dev *rt2x00dev); - /* * PCI driver handlers. */ diff --git a/drivers/net/wireless/rt2x00/rt61pci.c b/drivers/net/wireless/rt2x00/rt61pci.c index f95792cfcf89..9e3c8ff53e3f 100644 --- a/drivers/net/wireless/rt2x00/rt61pci.c +++ b/drivers/net/wireless/rt2x00/rt61pci.c @@ -35,6 +35,7 @@ #include #include "rt2x00.h" +#include "rt2x00mmio.h" #include "rt2x00pci.h" #include "rt61pci.h" -- cgit v1.2.3 From e2409d83434d77874b461b78af6a19cd6e6a1280 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Sun, 31 Mar 2013 17:02:04 +0000 Subject: r8169: fix auto speed down issue It would cause no link after suspending or shutdowning when the nic changes the speed to 10M and connects to a link partner which forces the speed to 100M. Check the link partner ability to determine which speed to set. Signed-off-by: Hayes Wang Acked-by: Francois Romieu Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 28 +++++++++++++++++++++++++--- 1 file changed, 25 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 28fb50a1e9c3..4ecbe64a758d 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -3818,6 +3818,30 @@ static void rtl_init_mdio_ops(struct rtl8169_private *tp) } } +static void rtl_speed_down(struct rtl8169_private *tp) +{ + u32 adv; + int lpa; + + rtl_writephy(tp, 0x1f, 0x0000); + lpa = rtl_readphy(tp, MII_LPA); + + if (lpa & (LPA_10HALF | LPA_10FULL)) + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full; + else if (lpa & (LPA_100HALF | LPA_100FULL)) + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full; + else + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full | + (tp->mii.supports_gmii ? + ADVERTISED_1000baseT_Half | + ADVERTISED_1000baseT_Full : 0); + + rtl8169_set_speed(tp->dev, AUTONEG_ENABLE, SPEED_1000, DUPLEX_FULL, + adv); +} + static void rtl_wol_suspend_quirk(struct rtl8169_private *tp) { void __iomem *ioaddr = tp->mmio_addr; @@ -3848,9 +3872,7 @@ static bool rtl_wol_pll_power_down(struct rtl8169_private *tp) if (!(__rtl8169_get_wol(tp) & WAKE_ANY)) return false; - rtl_writephy(tp, 0x1f, 0x0000); - rtl_writephy(tp, MII_BMCR, 0x0000); - + rtl_speed_down(tp); rtl_wol_suspend_quirk(tp); return true; -- cgit v1.2.3 From 31d1670e73f4911fe401273a8f576edc9c2b5fea Mon Sep 17 00:00:00 2001 From: Hannes Frederic Sowa Date: Tue, 2 Apr 2013 14:36:46 +0000 Subject: atl1e: limit gso segment size to prevent generation of wrong ip length fields The limit of 0x3c00 is taken from the windows driver. Suggested-by: Huang, Xiong Cc: Huang, Xiong Cc: Eric Dumazet Signed-off-by: Hannes Frederic Sowa Signed-off-by: David S. Miller --- drivers/net/ethernet/atheros/atl1e/atl1e.h | 2 +- drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e.h b/drivers/net/ethernet/atheros/atl1e/atl1e.h index edfdf6b950e7..b5fd934585e9 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e.h +++ b/drivers/net/ethernet/atheros/atl1e/atl1e.h @@ -186,7 +186,7 @@ struct atl1e_tpd_desc { /* how about 0x2000 */ #define MAX_TX_BUF_LEN 0x2000 #define MAX_TX_BUF_SHIFT 13 -/*#define MAX_TX_BUF_LEN 0x3000 */ +#define MAX_TSO_SEG_SIZE 0x3c00 /* rrs word 1 bit 0:31 */ #define RRS_RX_CSUM_MASK 0xFFFF diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c index f73d5609439a..ac25f05ff68f 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c +++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c @@ -2329,6 +2329,7 @@ static int atl1e_probe(struct pci_dev *pdev, const struct pci_device_id *ent) INIT_WORK(&adapter->reset_task, atl1e_reset_task); INIT_WORK(&adapter->link_chg_task, atl1e_link_chg_task); + netif_set_gso_max_size(netdev, MAX_TSO_SEG_SIZE); err = register_netdev(netdev); if (err) { netdev_err(netdev, "register netdevice failed\n"); -- cgit v1.2.3 From 4de79c737b200492195ebc54a887075327e1ec1d Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Wed, 3 Apr 2013 05:46:33 +0000 Subject: bonding: remove sysfs before removing devices We have a race condition if we try to rmmod bonding and simultaneously add a bond master through sysfs. In bonding_exit() we first remove the devices (through rtnl_link_unregister() ) and only after that we remove the sysfs. If we manage to add a device through sysfs after that the devices were removed - we'll end up with that device/sysfs structure and with the module unloaded. Fix this by first removing the sysfs and only after that calling rtnl_link_unregister(). Signed-off-by: Veaceslav Falico Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index a51241b2e621..171b10f167a5 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -4902,8 +4902,8 @@ static void __exit bonding_exit(void) bond_destroy_debugfs(); - rtnl_link_unregister(&bond_link_ops); unregister_pernet_subsys(&bond_net_ops); + rtnl_link_unregister(&bond_link_ops); #ifdef CONFIG_NET_POLL_CONTROLLER /* -- cgit v1.2.3 From f01fc1a82c2ee68726b400fadb156bd623b5f2f1 Mon Sep 17 00:00:00 2001 From: Jakub Kicinski Date: Wed, 3 Apr 2013 16:50:54 +0000 Subject: ixgbe: fix registration order of driver and DCA nofitication ixgbe_notify_dca cannot be called before driver registration because it expects driver's klist_devices to be allocated and initialized. While on it make sure debugfs files are removed when registration fails. Cc: stable Signed-off-by: Jakub Kicinski Tested-by: Phil Schmitt Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index db5611ae407e..79f4a26ea6cc 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -7922,12 +7922,19 @@ static int __init ixgbe_init_module(void) ixgbe_dbg_init(); #endif /* CONFIG_DEBUG_FS */ + ret = pci_register_driver(&ixgbe_driver); + if (ret) { +#ifdef CONFIG_DEBUG_FS + ixgbe_dbg_exit(); +#endif /* CONFIG_DEBUG_FS */ + return ret; + } + #ifdef CONFIG_IXGBE_DCA dca_register_notify(&dca_notifier); #endif - ret = pci_register_driver(&ixgbe_driver); - return ret; + return 0; } module_init(ixgbe_init_module); -- cgit v1.2.3 From cb28ea3b13b86fb23448525f34720e659bda7aa8 Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Sun, 7 Apr 2013 05:36:23 +0000 Subject: bnx2x: Fix KR2 rapid link flap Check KR2 recovery time at the beginning of the work-around function. Signed-off-by: Yaniv Rosner Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index 77ebae0ac64a..0283f343b0d1 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -13437,13 +13437,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, { struct bnx2x *bp = params->bp; u16 base_page, next_page, not_kr2_device, lane; - int sigdet = bnx2x_warpcore_get_sigdet(phy, params); - - if (!sigdet) { - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) - bnx2x_kr2_recovery(params, vars, phy); - return; - } + int sigdet; /* Once KR2 was disabled, wait 5 seconds before checking KR2 recovery * since some switches tend to reinit the AN process and clear the @@ -13454,6 +13448,16 @@ static void bnx2x_check_kr2_wa(struct link_params *params, vars->check_kr2_recovery_cnt--; return; } + + sigdet = bnx2x_warpcore_get_sigdet(phy, params); + if (!sigdet) { + if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + bnx2x_kr2_recovery(params, vars, phy); + DP(NETIF_MSG_LINK, "No sigdet\n"); + } + return; + } + lane = bnx2x_get_warpcore_lane(phy, params); CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, MDIO_AER_BLOCK_AER_REG, lane); -- cgit v1.2.3 From fd5c07a8d6a10c7112b19f3b0d428627c62b06ab Mon Sep 17 00:00:00 2001 From: Haiyang Zhang Date: Fri, 5 Apr 2013 11:44:39 +0000 Subject: hyperv: Fix a kernel warning from netvsc_linkstatus_callback() The warning about local_bh_enable inside IRQ happens when disconnecting a virtual NIC. The reason for the warning is -- netif_tx_disable() is called when the NIC is disconnected. And it's called within irq context. netif_tx_disable() calls local_bh_enable() which displays warning if in irq. The fix is to remove the unnecessary netif_tx_disable & wake_queue() in the netvsc_linkstatus_callback(). Reported-by: Richard Genoud Tested-by: Long Li Tested-by: Richard Genoud Signed-off-by: Haiyang Zhang Reviewed-by: K. Y. Srinivasan Signed-off-by: David S. Miller --- drivers/net/hyperv/netvsc_drv.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/hyperv/netvsc_drv.c b/drivers/net/hyperv/netvsc_drv.c index 5f85205cd12b..8341b62e5521 100644 --- a/drivers/net/hyperv/netvsc_drv.c +++ b/drivers/net/hyperv/netvsc_drv.c @@ -241,13 +241,11 @@ void netvsc_linkstatus_callback(struct hv_device *device_obj, if (status == 1) { netif_carrier_on(net); - netif_wake_queue(net); ndev_ctx = netdev_priv(net); schedule_delayed_work(&ndev_ctx->dwork, 0); schedule_delayed_work(&ndev_ctx->dwork, msecs_to_jiffies(20)); } else { netif_carrier_off(net); - netif_tx_disable(net); } } -- cgit v1.2.3 From f1ea3cd70110d482ef1ce6ef158df113aa366f43 Mon Sep 17 00:00:00 2001 From: Haiyang Zhang Date: Fri, 5 Apr 2013 11:44:40 +0000 Subject: hyperv: Fix RNDIS send_completion code path In some cases, the VM_PKT_COMP message can arrive later than RNDIS completion message, which will free the packet memory. This may cause panic due to access to freed memory in netvsc_send_completion(). This patch fixes this problem by removing rndis_filter_send_request_completion() from the code path. The function was a no-op. Reported-by: Long Li Tested-by: Long Li Signed-off-by: Haiyang Zhang Reviewed-by: K. Y. Srinivasan Signed-off-by: David S. Miller --- drivers/net/hyperv/netvsc.c | 17 ++++++++++++----- drivers/net/hyperv/rndis_filter.c | 14 +------------- 2 files changed, 13 insertions(+), 18 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/hyperv/netvsc.c b/drivers/net/hyperv/netvsc.c index 1cd77483da50..f5f0f09e4cc5 100644 --- a/drivers/net/hyperv/netvsc.c +++ b/drivers/net/hyperv/netvsc.c @@ -470,8 +470,10 @@ static void netvsc_send_completion(struct hv_device *device, packet->trans_id; /* Notify the layer above us */ - nvsc_packet->completion.send.send_completion( - nvsc_packet->completion.send.send_completion_ctx); + if (nvsc_packet) + nvsc_packet->completion.send.send_completion( + nvsc_packet->completion.send. + send_completion_ctx); num_outstanding_sends = atomic_dec_return(&net_device->num_outstanding_sends); @@ -498,6 +500,7 @@ int netvsc_send(struct hv_device *device, int ret = 0; struct nvsp_message sendMessage; struct net_device *ndev; + u64 req_id; net_device = get_outbound_net_device(device); if (!net_device) @@ -518,20 +521,24 @@ int netvsc_send(struct hv_device *device, 0xFFFFFFFF; sendMessage.msg.v1_msg.send_rndis_pkt.send_buf_section_size = 0; + if (packet->completion.send.send_completion) + req_id = (u64)packet; + else + req_id = 0; + if (packet->page_buf_cnt) { ret = vmbus_sendpacket_pagebuffer(device->channel, packet->page_buf, packet->page_buf_cnt, &sendMessage, sizeof(struct nvsp_message), - (unsigned long)packet); + req_id); } else { ret = vmbus_sendpacket(device->channel, &sendMessage, sizeof(struct nvsp_message), - (unsigned long)packet, + req_id, VM_PKT_DATA_INBAND, VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED); - } if (ret == 0) { diff --git a/drivers/net/hyperv/rndis_filter.c b/drivers/net/hyperv/rndis_filter.c index 2b657d4d63a8..0775f0aefd1e 100644 --- a/drivers/net/hyperv/rndis_filter.c +++ b/drivers/net/hyperv/rndis_filter.c @@ -61,9 +61,6 @@ struct rndis_request { static void rndis_filter_send_completion(void *ctx); -static void rndis_filter_send_request_completion(void *ctx); - - static struct rndis_device *get_rndis_device(void) { @@ -241,10 +238,7 @@ static int rndis_filter_send_request(struct rndis_device *dev, packet->page_buf[0].len; } - packet->completion.send.send_completion_ctx = req;/* packet; */ - packet->completion.send.send_completion = - rndis_filter_send_request_completion; - packet->completion.send.send_completion_tid = (unsigned long)dev; + packet->completion.send.send_completion = NULL; ret = netvsc_send(dev->net_dev->dev, packet); return ret; @@ -999,9 +993,3 @@ static void rndis_filter_send_completion(void *ctx) /* Pass it back to the original handler */ filter_pkt->completion(filter_pkt->completion_ctx); } - - -static void rndis_filter_send_request_completion(void *ctx) -{ - /* Noop */ -} -- cgit v1.2.3 From b50b72de2f2feed4adfbd8e18610a393b5a04cc7 Mon Sep 17 00:00:00 2001 From: willy tarreau Date: Sat, 6 Apr 2013 08:47:01 +0000 Subject: net: mvneta: enable features before registering the driver It seems that the reason why the dev features were ignored was because they were enabled after registeration. Signed-off-by: Willy Tarreau Acked-by: Thomas Petazzoni Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/mvneta.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c index cd345b8969bc..1e628ce57201 100644 --- a/drivers/net/ethernet/marvell/mvneta.c +++ b/drivers/net/ethernet/marvell/mvneta.c @@ -2771,16 +2771,17 @@ static int mvneta_probe(struct platform_device *pdev) netif_napi_add(dev, &pp->napi, mvneta_poll, pp->weight); + dev->features = NETIF_F_SG | NETIF_F_IP_CSUM; + dev->hw_features |= NETIF_F_SG | NETIF_F_IP_CSUM; + dev->vlan_features |= NETIF_F_SG | NETIF_F_IP_CSUM; + dev->priv_flags |= IFF_UNICAST_FLT; + err = register_netdev(dev); if (err < 0) { dev_err(&pdev->dev, "failed to register\n"); goto err_deinit; } - dev->features = NETIF_F_SG | NETIF_F_IP_CSUM; - dev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM; - dev->priv_flags |= IFF_UNICAST_FLT; - netdev_info(dev, "mac: %pM\n", dev->dev_addr); platform_set_drvdata(pdev, pp->dev); -- cgit v1.2.3 From ffcdedb667b6db8ee31c7efa76a3ec59d9c3b0fc Mon Sep 17 00:00:00 2001 From: "nikolay@redhat.com" Date: Sat, 6 Apr 2013 00:54:37 +0000 Subject: Revert "bonding: remove sysfs before removing devices" This reverts commit 4de79c737b200492195ebc54a887075327e1ec1d. This patch introduces a new bug which causes access to freed memory. In bond_uninit: list_del(&bond->bond_list); bond_list is linked in bond_net's dev_list which is freed by unregister_pernet_subsys. Signed-off-by: Nikolay Aleksandrov Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 171b10f167a5..a51241b2e621 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -4902,8 +4902,8 @@ static void __exit bonding_exit(void) bond_destroy_debugfs(); - unregister_pernet_subsys(&bond_net_ops); rtnl_link_unregister(&bond_link_ops); + unregister_pernet_subsys(&bond_net_ops); #ifdef CONFIG_NET_POLL_CONTROLLER /* -- cgit v1.2.3 From 69b0216ac255f523556fa3d4ff030d857eaaa37f Mon Sep 17 00:00:00 2001 From: "nikolay@redhat.com" Date: Sat, 6 Apr 2013 00:54:38 +0000 Subject: bonding: fix bonding_masters race condition in bond unloading While the bonding module is unloading, it is considered that after rtnl_link_unregister all bond devices are destroyed but since no synchronization mechanism exists, a new bond device can be created via bonding_masters before unregister_pernet_subsys which would lead to multiple problems (e.g. NULL pointer dereference, wrong RIP, list corruption). This patch fixes the issue by removing any bond devices left in the netns after bonding_masters is removed from sysfs. Signed-off-by: Nikolay Aleksandrov Acked-by: Veaceslav Falico Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index a51241b2e621..07401a3e256b 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -4846,9 +4846,18 @@ static int __net_init bond_net_init(struct net *net) static void __net_exit bond_net_exit(struct net *net) { struct bond_net *bn = net_generic(net, bond_net_id); + struct bonding *bond, *tmp_bond; + LIST_HEAD(list); bond_destroy_sysfs(bn); bond_destroy_proc_dir(bn); + + /* Kill off any bonds created after unregistering bond rtnl ops */ + rtnl_lock(); + list_for_each_entry_safe(bond, tmp_bond, &bn->dev_list, bond_list) + unregister_netdevice_queue(bond->dev, &list); + unregister_netdevice_many(&list); + rtnl_unlock(); } static struct pernet_operations bond_net_ops = { -- cgit v1.2.3 From 61a0f6efc8932e9914e1782ff3a027e23c687fc6 Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Tue, 9 Apr 2013 23:19:00 +0000 Subject: e100: Add dma mapping error check e100 uses pci_map_single, but fails to check for a dma mapping error after its use, resulting in a stack trace: [ 46.656594] ------------[ cut here ]------------ [ 46.657004] WARNING: at lib/dma-debug.c:933 check_unmap+0x47b/0x950() [ 46.657004] Hardware name: To Be Filled By O.E.M. [ 46.657004] e100 0000:00:0e.0: DMA-API: device driver failed to check map error[device address=0x000000007a4540fa] [size=90 bytes] [mapped as single] [ 46.657004] Modules linked in: [ 46.657004] w83627hf hwmon_vid snd_via82xx ppdev snd_ac97_codec ac97_bus snd_seq snd_pcm snd_mpu401 snd_mpu401_uart ns558 snd_rawmidi gameport parport_pc e100 snd_seq_device parport snd_page_alloc snd_timer snd soundcore skge shpchp k8temp mii edac_core i2c_viapro edac_mce_amd nfsd auth_rpcgss nfs_acl lockd sunrpc binfmt_misc uinput ata_generic pata_acpi radeon i2c_algo_bit drm_kms_helper ttm firewire_ohci drm firewire_core pata_via sata_via i2c_core sata_promise crc_itu_t [ 46.657004] Pid: 792, comm: ip Not tainted 3.8.0-0.rc6.git0.1.fc19.x86_64 #1 [ 46.657004] Call Trace: [ 46.657004] [] warn_slowpath_common+0x70/0xa0 [ 46.657004] [] warn_slowpath_fmt+0x4c/0x50 [ 46.657004] [] check_unmap+0x47b/0x950 [ 46.657004] [] debug_dma_unmap_page+0x5f/0x70 [ 46.657004] [] ? e100_tx_clean+0x30/0x210 [e100] [ 46.657004] [] e100_tx_clean+0xe8/0x210 [e100] [ 46.657004] [] e100_poll+0x56f/0x6c0 [e100] [ 46.657004] [] ? net_rx_action+0xa1/0x370 [ 46.657004] [] net_rx_action+0x172/0x370 [ 46.657004] [] __do_softirq+0xef/0x3d0 [ 46.657004] [] call_softirq+0x1c/0x30 [ 46.657004] [] do_softirq+0x85/0xc0 [ 46.657004] [] irq_exit+0xd5/0xe0 [ 46.657004] [] do_IRQ+0x56/0xc0 [ 46.657004] [] common_interrupt+0x72/0x72 [ 46.657004] [] ? _raw_spin_unlock_irqrestore+0x3b/0x70 [ 46.657004] [] __slab_free+0x58/0x38b [ 46.657004] [] ? fsnotify_clear_marks_by_inode+0x34/0x120 [ 46.657004] [] ? kmem_cache_free+0x97/0x320 [ 46.657004] [] ? sock_destroy_inode+0x34/0x40 [ 46.657004] [] ? sock_destroy_inode+0x34/0x40 [ 46.657004] [] kmem_cache_free+0x312/0x320 [ 46.657004] [] sock_destroy_inode+0x34/0x40 [ 46.657004] [] destroy_inode+0x38/0x60 [ 46.657004] [] evict+0x10e/0x1a0 [ 46.657004] [] iput+0xf5/0x180 [ 46.657004] [] dput+0x248/0x310 [ 46.657004] [] __fput+0x171/0x240 [ 46.657004] [] ____fput+0xe/0x10 [ 46.657004] [] task_work_run+0xac/0xe0 [ 46.657004] [] do_exit+0x26d/0xc30 [ 46.657004] [] ? finish_task_switch+0x7c/0x120 [ 46.657004] [] ? retint_swapgs+0x13/0x1b [ 46.657004] [] do_group_exit+0x49/0xc0 [ 46.657004] [] sys_exit_group+0x14/0x20 [ 46.657004] [] system_call_fastpath+0x16/0x1b [ 46.657004] ---[ end trace 4468c44e2156e7d1 ]--- [ 46.657004] Mapped at: [ 46.657004] [] debug_dma_map_page+0x91/0x140 [ 46.657004] [] e100_xmit_prepare+0x12b/0x1c0 [e100] [ 46.657004] [] e100_exec_cb+0x84/0x140 [e100] [ 46.657004] [] e100_xmit_frame+0x3a/0x190 [e100] [ 46.657004] [] dev_hard_start_xmit+0x259/0x6c0 Easy fix, modify the cb paramter to e100_exec_cb to return an error, and do the dma_mapping_error check in the obvious place This was reported previously here: http://article.gmane.org/gmane.linux.network/257893 But nobody stepped up and fixed it. CC: Josh Boyer CC: e1000-devel@lists.sourceforge.net Signed-off-by: Neil Horman Reported-by: Michal Jaegermann Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/e100.c | 36 +++++++++++++++++++++++++----------- 1 file changed, 25 insertions(+), 11 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e100.c b/drivers/net/ethernet/intel/e100.c index ec800b093e7e..d2bea3f07c73 100644 --- a/drivers/net/ethernet/intel/e100.c +++ b/drivers/net/ethernet/intel/e100.c @@ -870,7 +870,7 @@ err_unlock: } static int e100_exec_cb(struct nic *nic, struct sk_buff *skb, - void (*cb_prepare)(struct nic *, struct cb *, struct sk_buff *)) + int (*cb_prepare)(struct nic *, struct cb *, struct sk_buff *)) { struct cb *cb; unsigned long flags; @@ -888,10 +888,13 @@ static int e100_exec_cb(struct nic *nic, struct sk_buff *skb, nic->cbs_avail--; cb->skb = skb; + err = cb_prepare(nic, cb, skb); + if (err) + goto err_unlock; + if (unlikely(!nic->cbs_avail)) err = -ENOSPC; - cb_prepare(nic, cb, skb); /* Order is important otherwise we'll be in a race with h/w: * set S-bit in current first, then clear S-bit in previous. */ @@ -1091,7 +1094,7 @@ static void e100_get_defaults(struct nic *nic) nic->mii.mdio_write = mdio_write; } -static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb) +static int e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb) { struct config *config = &cb->u.config; u8 *c = (u8 *)config; @@ -1181,6 +1184,7 @@ static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb) netif_printk(nic, hw, KERN_DEBUG, nic->netdev, "[16-23]=%02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n", c[16], c[17], c[18], c[19], c[20], c[21], c[22], c[23]); + return 0; } /************************************************************************* @@ -1331,7 +1335,7 @@ static const struct firmware *e100_request_firmware(struct nic *nic) return fw; } -static void e100_setup_ucode(struct nic *nic, struct cb *cb, +static int e100_setup_ucode(struct nic *nic, struct cb *cb, struct sk_buff *skb) { const struct firmware *fw = (void *)skb; @@ -1358,6 +1362,7 @@ static void e100_setup_ucode(struct nic *nic, struct cb *cb, cb->u.ucode[min_size] |= cpu_to_le32((BUNDLESMALL) ? 0xFFFF : 0xFF80); cb->command = cpu_to_le16(cb_ucode | cb_el); + return 0; } static inline int e100_load_ucode_wait(struct nic *nic) @@ -1400,18 +1405,20 @@ static inline int e100_load_ucode_wait(struct nic *nic) return err; } -static void e100_setup_iaaddr(struct nic *nic, struct cb *cb, +static int e100_setup_iaaddr(struct nic *nic, struct cb *cb, struct sk_buff *skb) { cb->command = cpu_to_le16(cb_iaaddr); memcpy(cb->u.iaaddr, nic->netdev->dev_addr, ETH_ALEN); + return 0; } -static void e100_dump(struct nic *nic, struct cb *cb, struct sk_buff *skb) +static int e100_dump(struct nic *nic, struct cb *cb, struct sk_buff *skb) { cb->command = cpu_to_le16(cb_dump); cb->u.dump_buffer_addr = cpu_to_le32(nic->dma_addr + offsetof(struct mem, dump_buf)); + return 0; } static int e100_phy_check_without_mii(struct nic *nic) @@ -1581,7 +1588,7 @@ static int e100_hw_init(struct nic *nic) return 0; } -static void e100_multi(struct nic *nic, struct cb *cb, struct sk_buff *skb) +static int e100_multi(struct nic *nic, struct cb *cb, struct sk_buff *skb) { struct net_device *netdev = nic->netdev; struct netdev_hw_addr *ha; @@ -1596,6 +1603,7 @@ static void e100_multi(struct nic *nic, struct cb *cb, struct sk_buff *skb) memcpy(&cb->u.multi.addr[i++ * ETH_ALEN], &ha->addr, ETH_ALEN); } + return 0; } static void e100_set_multicast_list(struct net_device *netdev) @@ -1756,11 +1764,18 @@ static void e100_watchdog(unsigned long data) round_jiffies(jiffies + E100_WATCHDOG_PERIOD)); } -static void e100_xmit_prepare(struct nic *nic, struct cb *cb, +static int e100_xmit_prepare(struct nic *nic, struct cb *cb, struct sk_buff *skb) { + dma_addr_t dma_addr; cb->command = nic->tx_command; + dma_addr = pci_map_single(nic->pdev, + skb->data, skb->len, PCI_DMA_TODEVICE); + /* If we can't map the skb, have the upper layer try later */ + if (pci_dma_mapping_error(nic->pdev, dma_addr)) + return -ENOMEM; + /* * Use the last 4 bytes of the SKB payload packet as the CRC, used for * testing, ie sending frames with bad CRC. @@ -1777,11 +1792,10 @@ static void e100_xmit_prepare(struct nic *nic, struct cb *cb, cb->u.tcb.tcb_byte_count = 0; cb->u.tcb.threshold = nic->tx_threshold; cb->u.tcb.tbd_count = 1; - cb->u.tcb.tbd.buf_addr = cpu_to_le32(pci_map_single(nic->pdev, - skb->data, skb->len, PCI_DMA_TODEVICE)); - /* check for mapping failure? */ + cb->u.tcb.tbd.buf_addr = cpu_to_le32(dma_addr); cb->u.tcb.tbd.size = cpu_to_le16(skb->len); skb_tx_timestamp(skb); + return 0; } static netdev_tx_t e100_xmit_frame(struct sk_buff *skb, -- cgit v1.2.3 From fea75645342c7ad574214497a78e562db12dfd7b Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Wed, 10 Apr 2013 13:34:39 +0300 Subject: bnx2x: Prevent null pointer dereference in AFEX mode The cnic module is responsible for initializing various bnx2x structs via callbacks provided by the bnx2x module. One such struct is the queue object for the FCoE queue. If a device is working in AFEX mode and its configuration allows FCoE yet the cnic module is not loaded, it's very likely a null pointer dereference will occur, as the bnx2x will erroneously access the FCoE's queue object. Prevent said access until cnic properly registers itself. Signed-off-by: Yuval Mintz Signed-off-by: Ariel Elior Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c index e81a747ea8ce..8e58da909f5c 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c @@ -4947,7 +4947,7 @@ static void bnx2x_after_function_update(struct bnx2x *bp) q); } - if (!NO_FCOE(bp)) { + if (!NO_FCOE(bp) && CNIC_ENABLED(bp)) { fp = &bp->fp[FCOE_IDX(bp)]; queue_params.q_obj = &bnx2x_sp_obj(bp, fp).q_obj; @@ -13354,6 +13354,7 @@ static int bnx2x_unregister_cnic(struct net_device *dev) RCU_INIT_POINTER(bp->cnic_ops, NULL); mutex_unlock(&bp->cnic_mutex); synchronize_rcu(); + bp->cnic_enabled = false; kfree(bp->cnic_kwq); bp->cnic_kwq = NULL; -- cgit v1.2.3