From af35e28f0fea877832fa27802bc862b2a912f32a Mon Sep 17 00:00:00 2001 From: Hakan Jansson Date: Mon, 30 May 2022 17:02:18 +0200 Subject: Bluetooth: hci_bcm: Add support for FW loading in autobaud mode Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable startup in autobaud mode. If the property is present, the device is started in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the device. Also prevent the use of unsupported commands for devices started in autobaud mode. Only a limited subset of HCI commands are supported in autobaud mode. Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading. Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate in normal mode when first powered on. Signed-off-by: Hakan Jansson Signed-off-by: Marcel Holtmann --- drivers/bluetooth/hci_bcm.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) (limited to 'drivers/bluetooth/hci_bcm.c') diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c index 785f445dd60d..4309654f95a5 100644 --- a/drivers/bluetooth/hci_bcm.c +++ b/drivers/bluetooth/hci_bcm.c @@ -99,6 +99,7 @@ struct bcm_device_data { * @no_early_set_baudrate: don't set_baudrate before setup() * @drive_rts_on_open: drive RTS signal on ->open() when platform requires it * @pcm_int_params: keep the initial PCM configuration + * @use_autobaud_mode: start Bluetooth device in autobaud mode */ struct bcm_device { /* Must be the first member, hci_serdev.c expects this. */ @@ -136,6 +137,7 @@ struct bcm_device { #endif bool no_early_set_baudrate; bool drive_rts_on_open; + bool use_autobaud_mode; u8 pcm_int_params[5]; }; @@ -472,7 +474,9 @@ static int bcm_open(struct hci_uart *hu) out: if (bcm->dev) { - if (bcm->dev->drive_rts_on_open) + if (bcm->dev->use_autobaud_mode) + hci_uart_set_flow_control(hu, false); /* Assert BT_UART_CTS_N */ + else if (bcm->dev->drive_rts_on_open) hci_uart_set_flow_control(hu, true); hu->init_speed = bcm->dev->init_speed; @@ -564,6 +568,7 @@ static int bcm_setup(struct hci_uart *hu) { struct bcm_data *bcm = hu->priv; bool fw_load_done = false; + bool use_autobaud_mode = (bcm->dev ? bcm->dev->use_autobaud_mode : 0); unsigned int speed; int err; @@ -572,7 +577,7 @@ static int bcm_setup(struct hci_uart *hu) hu->hdev->set_diag = bcm_set_diag; hu->hdev->set_bdaddr = btbcm_set_bdaddr; - err = btbcm_initialize(hu->hdev, &fw_load_done); + err = btbcm_initialize(hu->hdev, &fw_load_done, use_autobaud_mode); if (err) return err; @@ -616,7 +621,7 @@ static int bcm_setup(struct hci_uart *hu) btbcm_write_pcm_int_params(hu->hdev, ¶ms); } - err = btbcm_finalize(hu->hdev, &fw_load_done); + err = btbcm_finalize(hu->hdev, &fw_load_done, use_autobaud_mode); if (err) return err; @@ -1197,6 +1202,11 @@ static int bcm_acpi_probe(struct bcm_device *dev) static int bcm_of_probe(struct bcm_device *bdev) { + bdev->use_autobaud_mode = device_property_read_bool(bdev->dev, + "brcm,requires-autobaud-mode"); + if (bdev->use_autobaud_mode) + bdev->no_early_set_baudrate = true; + device_property_read_u32(bdev->dev, "max-speed", &bdev->oper_speed); device_property_read_u8_array(bdev->dev, "brcm,bt-pcm-int-params", bdev->pcm_int_params, 5); -- cgit v1.2.3