From 00dddcaa51f997cdc6dbae3303a31024e29a0fc0 Mon Sep 17 00:00:00 2001 From: Lars Poeschel Date: Tue, 28 May 2013 10:24:57 +0200 Subject: ARM: dts: AM33xx: Fix properties on gpmc node The gpmc driver is actually looking for "gpmc,num-cs" and "gpmc,num-waitpins" properties in DT. The binding doc also states this. Correct the properties in the dts to provide the right values for the gpmc driver. Signed-off-by: Lars Poeschel Acked-by: Peter Korsgaard Acked-by: Pekon Gupta Signed-off-by: Benoit Cousson --- arch/arm/boot/dts/am33xx.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 1460d9b88adf..8e1248f01fab 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -409,8 +409,8 @@ ti,hwmods = "gpmc"; reg = <0x50000000 0x2000>; interrupts = <100>; - num-cs = <7>; - num-waitpins = <2>; + gpmc,num-cs = <7>; + gpmc,num-waitpins = <2>; #address-cells = <2>; #size-cells = <1>; status = "disabled"; -- cgit v1.2.3 From 1e68f43b7dcf0e5eee10baeb3cbe4e1ca59db9fd Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Fri, 24 May 2013 17:24:21 -0700 Subject: ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line Earlier commits ensured proper muxing of pins related to proper TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC). However these only fixed legacy boot and not DT boot. For DT boot, the default mux values need to be set properly in DT. Special thanks to Nishanth Menon for the review and catching some major flaws in earlier versions. Tested on OMAP4430/Panda and OMAP4460/Panda-ES. Cc: Nishanth Menon Cc: Tony Lindgren Signed-off-by: Kevin Hilman Acked-by: Grygorii Strashko [benoit.cousson@linaro.org: Slightly change the subject to align board name with file name] Signed-off-by: Benoit Cousson --- arch/arm/boot/dts/omap4-panda-common.dtsi | 20 ++++++++++++++++++++ arch/arm/boot/dts/omap4-sdp.dts | 20 ++++++++++++++++++++ 2 files changed, 40 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 03bd60deb52b..eeb734e25709 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -56,9 +56,23 @@ }; }; +&omap4_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &twl6030_wkup_pins + >; + + twl6030_wkup_pins: pinmux_twl6030_wkup_pins { + pinctrl-single,pins = < + 0x14 0x2 /* fref_clk0_out.sys_drm_msecure OUTPUT | MODE2 */ + >; + }; +}; + &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < + &twl6030_pins &twl6040_pins &mcpdm_pins &mcbsp1_pins @@ -66,6 +80,12 @@ &tpd12s015_pins >; + twl6030_pins: pinmux_twl6030_pins { + pinctrl-single,pins = < + 0x15e 0x4118 /* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */ + >; + }; + twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */ diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index a35d9cd58063..98505a2ef162 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -142,9 +142,23 @@ }; }; +&omap4_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &twl6030_wkup_pins + >; + + twl6030_wkup_pins: pinmux_twl6030_wkup_pins { + pinctrl-single,pins = < + 0x14 0x2 /* fref_clk0_out.sys_drm_msecure OUTPUT | MODE2 */ + >; + }; +}; + &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < + &twl6030_pins &twl6040_pins &mcpdm_pins &dmic_pins @@ -179,6 +193,12 @@ >; }; + twl6030_pins: pinmux_twl6030_pins { + pinctrl-single,pins = < + 0x15e 0x4118 /* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */ + >; + }; + twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */ -- cgit v1.2.3 From 8341613afbc8d65bca8c81158edfb49f36b7ad92 Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Wed, 17 Apr 2013 18:23:15 -0500 Subject: ARM: dts: OMAP5: Fix missing PWM capability to timer nodes OMAP5 has 6 timers (GPTimers 5, 6, 8 to 11) that are capable of PWM. The PWM capability property is missing from the node definitions of couple of timers. Add ti,timer-pwm attribute for timer 5, 6, 8 and 11. Signed-off-by: Suman Anna [benoit.cousson@linaro.org: Update changelog and subject to highlight the fix] Signed-off-by: Benoit Cousson --- arch/arm/boot/dts/omap5.dtsi | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 3dd7ff825828..635cae283011 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -538,6 +538,7 @@ interrupts = <0 41 0x4>; ti,hwmods = "timer5"; ti,timer-dsp; + ti,timer-pwm; }; timer6: timer@4013a000 { @@ -574,6 +575,7 @@ reg = <0x4803e000 0x80>; interrupts = <0 45 0x4>; ti,hwmods = "timer9"; + ti,timer-pwm; }; timer10: timer@48086000 { @@ -581,6 +583,7 @@ reg = <0x48086000 0x80>; interrupts = <0 46 0x4>; ti,hwmods = "timer10"; + ti,timer-pwm; }; timer11: timer@48088000 { -- cgit v1.2.3 From 275236797916924103e133e3d7a7ea777c951273 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Wed, 29 May 2013 16:57:30 +0100 Subject: ARM: 7737/1: fix kernel decompressor compilation error with CONFIG_DEBUG_SEMIHOSTING Selecting this option produces: AS arch/arm/boot/compressed/debug.o arch/arm/boot/compressed/debug.S:4:33: fatal error: mach/debug-macro.S: No such file or directory compilation terminated. make[3]: *** [arch/arm/boot/compressed/debug.o] Error 1 The semihosting support cannot be modelled into a senduart macro as it requires memory space for argument passing. So the CONFIG_DEBUG_LL_INCLUDE may not have any sensible value and the include directive should be omitted. While at it, let's add proper semihosting output support to the decompressor. Signed-off-by: Nicolas Pitre Acked-by: Shawn Guo Signed-off-by: Russell King --- arch/arm/boot/compressed/debug.S | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/compressed/debug.S b/arch/arm/boot/compressed/debug.S index 6e8382d5b7a4..5392ee63338f 100644 --- a/arch/arm/boot/compressed/debug.S +++ b/arch/arm/boot/compressed/debug.S @@ -1,6 +1,8 @@ #include #include +#ifndef CONFIG_DEBUG_SEMIHOSTING + #include CONFIG_DEBUG_LL_INCLUDE ENTRY(putc) @@ -10,3 +12,29 @@ ENTRY(putc) busyuart r3, r1 mov pc, lr ENDPROC(putc) + +#else + +ENTRY(putc) + adr r1, 1f + ldmia r1, {r2, r3} + add r2, r2, r1 + ldr r1, [r2, r3] + strb r0, [r1] + mov r0, #0x03 @ SYS_WRITEC + ARM( svc #0x123456 ) + THUMB( svc #0xab ) + mov pc, lr + .align 2 +1: .word _GLOBAL_OFFSET_TABLE_ - . + .word semi_writec_buf(GOT) +ENDPROC(putc) + + .bss + .global semi_writec_buf + .type semi_writec_buf, %object +semi_writec_buf: + .space 4 + .size semi_writec_buf, 4 + +#endif -- cgit v1.2.3 From da94a829305f1c217cfdf6771cb1faca0917e3b9 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 31 May 2013 22:50:47 +0100 Subject: ARM: 7743/1: compressed/head.S: work around new binutils warning In August 2012, Matthew Gretton-Dann checked a change into binutils labelled "Error on obsolete & warn on deprecated registers", apparently as part of ARMv8 support. Apparently, this was supposed to emit the message "Warning: This coprocessor register access is deprecated in ARMv8" when using certain mcr/mrc instructions and building for ARMv8. Unfortunately, the message that is actually emitted appears to be '(null)', which is less helpful in comparison. Even more unfortunately, this is biting us on every single kernel build with a new gas, because arch/arm/boot/compressed/head.S and some other files in that directory are built with -march=all since kernel commit 80cec14a8 "[ARM] Add -march=all to assembly file build in arch/arm/boot/compressed" back in v2.6.28. This patch reverts Russell's nice solution and instead marks the head.S file to be built for armv7-a, which fortunately lets us build all instructions in that file without warnings even on the broken binutils. Without this patch, building anything results in: arch/arm/boot/compressed/head.S: Assembler messages: arch/arm/boot/compressed/head.S:565: Warning: (null) arch/arm/boot/compressed/head.S:676: Warning: (null) arch/arm/boot/compressed/head.S:698: Warning: (null) arch/arm/boot/compressed/head.S:722: Warning: (null) arch/arm/boot/compressed/head.S:726: Warning: (null) arch/arm/boot/compressed/head.S:957: Warning: (null) arch/arm/boot/compressed/head.S:996: Warning: (null) arch/arm/boot/compressed/head.S:997: Warning: (null) arch/arm/boot/compressed/head.S:1027: Warning: (null) arch/arm/boot/compressed/head.S:1035: Warning: (null) arch/arm/boot/compressed/head.S:1046: Warning: (null) arch/arm/boot/compressed/head.S:1060: Warning: (null) arch/arm/boot/compressed/head.S:1092: Warning: (null) arch/arm/boot/compressed/head.S:1094: Warning: (null) arch/arm/boot/compressed/head.S:1095: Warning: (null) arch/arm/boot/compressed/head.S:1102: Warning: (null) arch/arm/boot/compressed/head.S:1134: Warning: (null) Signed-off-by: Arnd Bergmann Cc: stable@vger.kernel.org Cc: Matthew Gretton-Dann Signed-off-by: Russell King --- arch/arm/boot/compressed/Makefile | 2 +- arch/arm/boot/compressed/head-sa1100.S | 1 + arch/arm/boot/compressed/head-shark.S | 1 + arch/arm/boot/compressed/head.S | 1 + 4 files changed, 4 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index 3580d57ea218..79e9bdbfc491 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -124,7 +124,7 @@ KBUILD_CFLAGS = $(subst -pg, , $(ORIG_CFLAGS)) endif ccflags-y := -fpic -mno-single-pic-base -fno-builtin -I$(obj) -asflags-y := -Wa,-march=all -DZIMAGE +asflags-y := -DZIMAGE # Supply kernel BSS size to the decompressor via a linker symbol. KBSS_SZ = $(shell $(CROSS_COMPILE)size $(obj)/../../../../vmlinux | \ diff --git a/arch/arm/boot/compressed/head-sa1100.S b/arch/arm/boot/compressed/head-sa1100.S index 6179d94dd5c6..3115e313d9f6 100644 --- a/arch/arm/boot/compressed/head-sa1100.S +++ b/arch/arm/boot/compressed/head-sa1100.S @@ -11,6 +11,7 @@ #include .section ".start", "ax" + .arch armv4 __SA1100_start: diff --git a/arch/arm/boot/compressed/head-shark.S b/arch/arm/boot/compressed/head-shark.S index 089c560e07f1..92b56897ed64 100644 --- a/arch/arm/boot/compressed/head-shark.S +++ b/arch/arm/boot/compressed/head-shark.S @@ -18,6 +18,7 @@ .section ".start", "ax" + .arch armv4 b __beginning __ofw_data: .long 0 @ the number of memory blocks diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index fe4d9c3ad761..693855995407 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -11,6 +11,7 @@ #include #include + .arch armv7-a /* * Debugging stuff * -- cgit v1.2.3 From ced2a3b84965f1be8b6a142d6029faf241f109af Mon Sep 17 00:00:00 2001 From: Marc C Date: Wed, 5 Jun 2013 22:02:23 +0100 Subject: ARM: 7750/1: update legacy CPU ID in decompressor cache support jump table The previous mask values for the legacy ARM CPU IDs were conflicting with the CPU ID assignments for late-generation CPUs (like the Qualcomm MSM/QSD or Broadcom Brahma-15 processors). This change corrects the legacy ARM CPU ID value so that the jump table can fall-through to the appropriate cache maintenance / MMU functions. Signed-off-by: Marc C Signed-off-by: Russell King --- arch/arm/boot/compressed/head.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index 693855995407..032a8d987148 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -806,8 +806,8 @@ call_cache_fn: adr r12, proc_types .align 2 .type proc_types,#object proc_types: - .word 0x00000000 @ old ARM ID - .word 0x0000f000 + .word 0x41000000 @ old ARM ID + .word 0xff00f000 mov pc, lr THUMB( nop ) mov pc, lr -- cgit v1.2.3 From 5f1f3d5088316f827591764aa6a5e7161eb514bd Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Thu, 6 Jun 2013 11:21:23 +0200 Subject: arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range The ranges DT entry needed by the PCIe controller is defined at the SoC .dtsi level. However, some boards have a NOR flash, and to support it, they need to override the SoC-level ranges property to add an additional range. Since PCIe and NOR support came separately, some boards were not properly changed to include the PCIe range in their ranges property at the .dts level. This commit fixes those platforms. Signed-off-by: Thomas Petazzoni Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-xp-gp.dts | 5 +++-- arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 5 +++-- 2 files changed, 6 insertions(+), 4 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index 3ee63d128e27..76db557adbe7 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -39,8 +39,9 @@ }; soc { - ranges = <0 0 0xd0000000 0x100000 - 0xf0000000 0 0xf0000000 0x1000000>; + ranges = <0 0 0xd0000000 0x100000 /* Internal registers 1MiB */ + 0xe0000000 0 0xe0000000 0x8100000 /* PCIe */ + 0xf0000000 0 0xf0000000 0x1000000 /* Device Bus, NOR 16MiB */>; internal-regs { serial@12000 { diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index 46b785064dd8..fdea75c73411 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -27,8 +27,9 @@ }; soc { - ranges = <0 0 0xd0000000 0x100000 - 0xf0000000 0 0xf0000000 0x8000000>; + ranges = <0 0 0xd0000000 0x100000 /* Internal registers 1MiB */ + 0xe0000000 0 0xe0000000 0x8100000 /* PCIe */ + 0xf0000000 0 0xf0000000 0x8000000 /* Device Bus, NOR 128MiB */>; internal-regs { serial@12000 { -- cgit v1.2.3 From 115581cfc9dc868b5f2c230d0236976276bc9dbb Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 4 Jun 2013 10:18:44 -0300 Subject: ARM: dts: mx28: Adjust the digctl compatible string MX28 has the same DIGCTL block as MX23, so adjust the compatible string to reflect that. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 600f7cb51f3e..0a265f3da037 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -669,7 +669,7 @@ }; digctl@8001c000 { - compatible = "fsl,imx28-digctl"; + compatible = "fsl,imx28-digctl", "fsl,imx23-digctl"; reg = <0x8001c000 0x2000>; interrupts = <89>; status = "disabled"; -- cgit v1.2.3 From f8040cf59714f1342898b54be6300ed70e66aed1 Mon Sep 17 00:00:00 2001 From: Eric Bénard Date: Mon, 8 Apr 2013 14:57:31 +0200 Subject: ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add auart2 2 pins configuration on its main pads Signed-off-by: Eric Bénard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 0a265f3da037..c39abe3f388f 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -330,6 +330,17 @@ fsl,pull-up = <0>; }; + auart2_2pins_b: auart2-2pins@1 { + reg = <1>; + fsl,pinmux-ids = < + 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */ + 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + auart3_pins_a: auart3@0 { reg = <0>; fsl,pinmux-ids = < -- cgit v1.2.3 From 4812e74616c084543db4448da0942a5c3fde5f87 Mon Sep 17 00:00:00 2001 From: Eric Bénard Date: Mon, 8 Apr 2013 14:57:32 +0200 Subject: ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add auart3 2 pins configuration on its main pads Signed-off-by: Eric Bénard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index c39abe3f388f..2790063e294f 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -365,6 +365,17 @@ fsl,pull-up = <0>; }; + auart3_2pins_b: auart3-2pins@1 { + reg = <1>; + fsl,pinmux-ids = < + 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ + 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + mac0_pins_a: mac0@0 { reg = <0>; fsl,pinmux-ids = < -- cgit v1.2.3 From 33678d123050f1be3da6de8e3f1b5b391742560d Mon Sep 17 00:00:00 2001 From: Eric Bénard Date: Mon, 8 Apr 2013 14:57:33 +0200 Subject: ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add auart4 2 pins configuration on SSP3 pads Signed-off-by: Eric Bénard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 2790063e294f..5ec78c907223 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -376,6 +376,17 @@ fsl,pull-up = <0>; }; + auart4_2pins_a: auart4@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */ + 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + mac0_pins_a: mac0@0 { reg = <0>; fsl,pinmux-ids = < -- cgit v1.2.3 From b400932c2944d36025e9240e877499ac5f613680 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 22 Apr 2013 11:55:55 +0200 Subject: ARM: dts: cfa10036: Change the OLED display to SSD1306 The SSD1307 was used in an early prototype that will never get distributed. The final board now has a SSD1306 instead, that has its own power generation unit and thus doesn't need any PWM. The panel attached to it also changed. Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-cfa10036.dts | 14 +++++--------- arch/arm/boot/dts/imx28-cfa10049.dts | 4 ++-- 2 files changed, 7 insertions(+), 11 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index 1594694532b9..40488f5a8504 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -58,12 +58,6 @@ }; apbx@80040000 { - pwm: pwm@80064000 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm4_pins_a>; - status = "okay"; - }; - duart: serial@80074000 { pinctrl-names = "default"; pinctrl-0 = <&duart_pins_b>; @@ -75,11 +69,13 @@ pinctrl-0 = <&i2c0_pins_b>; status = "okay"; - ssd1307: oled@3c { - compatible = "solomon,ssd1307fb-i2c"; + ssd1306: oled@3c { + compatible = "solomon,ssd1306fb-i2c"; reg = <0x3c>; - pwms = <&pwm 4 3000>; reset-gpios = <&gpio2 7 0>; + solomon,height = <32>; + solomon,width = <128>; + solomon,page-offset = <0>; }; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index 063e62059890..dfdcd85c265c 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -166,8 +166,8 @@ apbx@80040000 { pwm: pwm@80064000 { - pinctrl-names = "default", "default"; - pinctrl-1 = <&pwm3_pins_b>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_b>; status = "okay"; }; -- cgit v1.2.3 From b55cb191b03b64e02ffc635423afc0385b37df27 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 22 Apr 2013 12:02:22 +0200 Subject: ARM: cfa10036: dt: Change i2c0 clock frequency The OLED display can work faster. Change the i2c controller clock frequency to remove the tearing effect that can be seen on the display. Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-cfa10036.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index 40488f5a8504..a524cafa3dba 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -67,6 +67,7 @@ i2c0: i2c@80058000 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_b>; + clock-frequency = <400000>; status = "okay"; ssd1306: oled@3c { -- cgit v1.2.3 From 56924ad2b8eff55c5b4d32c61107a9eb136d9470 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Fri, 10 May 2013 14:26:35 +0200 Subject: ARM: mxs: Fix UARTs on M28EVK Make use of RTS/CTS lines on AUART0 and register AUART1 and AUART2 which are routed onto a pin header. Signed-off-by: Marek Vasut Cc: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-m28evk.dts | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 5aa44e05c9f5..880df2f13be8 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -220,7 +220,19 @@ auart0: serial@8006a000 { pinctrl-names = "default"; - pinctrl-0 = <&auart0_2pins_a>; + pinctrl-0 = <&auart0_pins_a>; + status = "okay"; + }; + + auart1: serial@8006c000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart1_pins_a>; + status = "okay"; + }; + + auart2: serial@8006e000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart2_2pins_b>; status = "okay"; }; }; -- cgit v1.2.3 From 25a7376a4dc2947dc89e91185387926fc106f879 Mon Sep 17 00:00:00 2001 From: Gwenhael Goavec-Merou Date: Fri, 17 May 2013 07:13:41 +0200 Subject: ARM: dts: apf28dev: Add touchscreen support for APF28dev Signed-off-by: Gwenhael Goavec-Merou Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-apf28dev.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts index 3d905d16cbec..b602494c152b 100644 --- a/arch/arm/boot/dts/imx28-apf28dev.dts +++ b/arch/arm/boot/dts/imx28-apf28dev.dts @@ -103,6 +103,7 @@ apbx@80040000 { lradc@80050000 { + fsl,lradc-touchscreen-wires = <4>; status = "okay"; }; -- cgit v1.2.3 From 17a2163881aa7df9ae83d75cc0671a1013399185 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 13 Jun 2013 15:43:42 +0200 Subject: ARM: cfa10036: Add USB0 OTG port Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-cfa10036.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index a524cafa3dba..94c4476972c3 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -45,6 +45,17 @@ fsl,voltage = <1>; fsl,pull-up = <0>; }; + + usb0_otg_cfa10036: otg-10036@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; ssp0: ssp@80010000 { @@ -79,6 +90,18 @@ solomon,page-offset = <0>; }; }; + + usbphy0: usbphy@8007c000 { + status = "okay"; + }; + }; + }; + + ahb@80080000 { + usb0: usb@80080000 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_otg_cfa10036>; + status = "okay"; }; }; -- cgit v1.2.3 From 65bc642f1b76442e8242a79fa0e48d49fda98ba8 Mon Sep 17 00:00:00 2001 From: Brian Lilly Date: Thu, 13 Jun 2013 15:43:43 +0200 Subject: ARM: cfa10049: Switch the chip select pin of the LCD controller The early prototypes had the chip select pin for the LCD controller wired on the GPIO 3-23, while the production run of the CFA-10049 have this chip select on the GPIO 3-5. Signed-off-by: Brian Lilly Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-cfa10049.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index dfdcd85c265c..04b2f769ffbd 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -33,7 +33,7 @@ 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */ 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */ 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */ - 0x3173 /* MX28_PAD_LCD_RESET__GPIO_3_23 */ + 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -265,7 +265,7 @@ gpio-sck = <&gpio2 16 0>; gpio-mosi = <&gpio2 17 0>; gpio-miso = <&gpio2 18 0>; - cs-gpios = <&gpio3 23 0>; + cs-gpios = <&gpio3 5 0>; num-chipselects = <1>; #address-cells = <1>; #size-cells = <0>; -- cgit v1.2.3 From ed138c368d95095de522db98b8b6929874bed403 Mon Sep 17 00:00:00 2001 From: Brian Lilly Date: Thu, 13 Jun 2013 15:43:44 +0200 Subject: ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree The CFA-10055 is yet another breakout board for the CFA-10036, and is basically a CFA-10037, with the screen and LCD controller found on the CFA-10049. Signed-off-by: Brian Lilly Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx28-cfa10055.dts | 179 +++++++++++++++++++++++++++++++++++ arch/arm/mach-mxs/mach-mxs.c | 15 +-- 3 files changed, 185 insertions(+), 10 deletions(-) create mode 100644 arch/arm/boot/dts/imx28-cfa10055.dts (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f0895c581a89..c80151331f4f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-cfa10036.dtb \ imx28-cfa10037.dtb \ imx28-cfa10049.dtb \ + imx28-cfa10055.dtb \ imx28-evk.dtb \ imx28-m28evk.dtb \ imx28-sps1.dtb \ diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts new file mode 100644 index 000000000000..158111244122 --- /dev/null +++ b/arch/arm/boot/dts/imx28-cfa10055.dts @@ -0,0 +1,179 @@ +/* + * Copyright 2013 Crystalfontz America, Inc. + * Free Electrons + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/* + * The CFA-10055 is an expansion board for the CFA-10036 module and + * CFA-10037, thus we need to include the CFA-10037 DTS. + */ +/include/ "imx28-cfa10037.dts" + +/ { + model = "Crystalfontz CFA-10055 Board"; + compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28"; + + apb@80000000 { + apbh@80000000 { + pinctrl@80018000 { + pinctrl-names = "default", "default"; + pinctrl-1 = <&hog_pins_cfa10055 + &hog_pins_cfa10055_pullup>; + + hog_pins_cfa10055: hog-10055@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + hog_pins_cfa10055_pullup: hog-10055-pullup@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + + spi2_pins_cfa10055: spi2-cfa10055@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ + 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ + 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ + >; + fsl,drive-strength = <1>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + + lcdif_18bit_pins_cfa10055: lcdif-18bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ + 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ + 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ + 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ + 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ + 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ + 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ + 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ + 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ + 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ + 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ + 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ + 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ + 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ + 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ + 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ + 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ + 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_pins_cfa10055: lcdif-evk@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ + 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ + 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_18bit_pins_cfa10055 + &lcdif_pins_cfa10055>; + display = <&display>; + status = "okay"; + + display: display { + bits-per-pixel = <32>; + bus-width = <18>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9216000>; + hactive = <320>; + vactive = <480>; + hback-porch = <2>; + hfront-porch = <2>; + vback-porch = <2>; + vfront-porch = <2>; + hsync-len = <15>; + vsync-len = <15>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; + }; + }; + + apbx@80040000 { + lradc@80050000 { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; + }; + + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_b>; + status = "okay"; + }; + }; + }; + + spi2 { + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_cfa10055>; + status = "okay"; + gpio-sck = <&gpio2 16 0>; + gpio-mosi = <&gpio2 17 0>; + gpio-miso = <&gpio2 18 0>; + cs-gpios = <&gpio3 5 0>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + + hx8357: hx8357@0 { + compatible = "himax,hx8357b", "himax,hx8357"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + gpios-reset = <&gpio3 30 0>; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 3 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; +}; diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index f0bf6076fa32..f9fe0c539031 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -368,12 +368,7 @@ static void __init tx28_post_init(void) pinctrl_put(pctl); } -static void __init cfa10049_init(void) -{ - update_fec_mac_prop(OUI_CRYSTALFONTZ); -} - -static void __init cfa10037_init(void) +static void __init crystalfontz_init(void) { update_fec_mac_prop(OUI_CRYSTALFONTZ); } @@ -482,10 +477,10 @@ static void __init mxs_machine_init(void) imx28_evk_init(); else if (of_machine_is_compatible("bluegiga,apx4devkit")) apx4devkit_init(); - else if (of_machine_is_compatible("crystalfontz,cfa10037")) - cfa10037_init(); - else if (of_machine_is_compatible("crystalfontz,cfa10049")) - cfa10049_init(); + else if (of_machine_is_compatible("crystalfontz,cfa10037") || + of_machine_is_compatible("crystalfontz,cfa10049") || + of_machine_is_compatible("crystalfontz,cfa10055")) + crystalfontz_init(); of_platform_populate(NULL, of_default_bus_match_table, mxs_auxdata_lookup, parent); -- cgit v1.2.3 From d75f3d92e86e65b3cb9725e65f7278cc303511db Mon Sep 17 00:00:00 2001 From: Brian Lilly Date: Thu, 13 Jun 2013 15:43:45 +0200 Subject: ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree The CFA-10057 is a breakout board for the CFA-10036 that has Ethernet, USB and a 4.3" LCD screen on it. Signed-off-by: Brian Lilly Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx28-cfa10057.dts | 191 +++++++++++++++++++++++++++++++++++ arch/arm/mach-mxs/mach-mxs.c | 3 +- 3 files changed, 194 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx28-cfa10057.dts (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c80151331f4f..225d93964a4f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -131,6 +131,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-cfa10037.dtb \ imx28-cfa10049.dtb \ imx28-cfa10055.dtb \ + imx28-cfa10057.dtb \ imx28-evk.dtb \ imx28-m28evk.dtb \ imx28-sps1.dtb \ diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts new file mode 100644 index 000000000000..2da713cdb42a --- /dev/null +++ b/arch/arm/boot/dts/imx28-cfa10057.dts @@ -0,0 +1,191 @@ +/* + * Copyright 2013 Crystalfontz America, Inc. + * Copyright 2012 Free Electrons + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/* + * The CFA-10057 is an expansion board for the CFA-10036 module, thus we + * need to include the CFA-10036 DTS. + */ +/include/ "imx28-cfa10036.dts" + +/ { + model = "Crystalfontz CFA-10057 Board"; + compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28"; + + apb@80000000 { + apbh@80000000 { + pinctrl@80018000 { + pinctrl-names = "default", "default"; + pinctrl-1 = <&hog_pins_cfa10057 + &hog_pins_cfa10057_pullup>; + + hog_pins_cfa10057: hog-10057@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + hog_pins_cfa10057_pullup: hog-10057-pullup@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */ + 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */ + 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */ + 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */ + 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + + lcdif_18bit_pins_cfa10057: lcdif-18bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ + 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ + 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ + 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ + 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ + 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ + 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ + 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ + 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ + 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ + 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ + 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ + 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ + 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ + 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ + 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ + 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ + 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_pins_cfa10057: lcdif-evk@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ + 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ + 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_18bit_pins_cfa10057 + &lcdif_pins_cfa10057>; + display = <&display>; + status = "okay"; + + display: display { + bits-per-pixel = <32>; + bus-width = <18>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <30000000>; + hactive = <480>; + vactive = <800>; + hfront-porch = <12>; + hback-porch = <2>; + vfront-porch = <5>; + vback-porch = <3>; + hsync-len = <2>; + vsync-len = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; + }; + }; + + apbx@80040000 { + lradc@80050000 { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; + }; + + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_b>; + status = "okay"; + }; + + i2c1: i2c@8005a000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + }; + + usbphy1: usbphy@8007e000 { + status = "okay"; + }; + }; + }; + + ahb@80080000 { + usb1: usb@80090000 { + vbus-supply = <®_usb1_vbus>; + pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_usb1_vbus: usb1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio0 7 1>; + }; + }; + + ahb@80080000 { + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-reset-gpios = <&gpio2 21 0>; + phy-reset-duration = <100>; + status = "okay"; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 3 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + }; +}; diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index f9fe0c539031..ba227cb2c93b 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -479,7 +479,8 @@ static void __init mxs_machine_init(void) apx4devkit_init(); else if (of_machine_is_compatible("crystalfontz,cfa10037") || of_machine_is_compatible("crystalfontz,cfa10049") || - of_machine_is_compatible("crystalfontz,cfa10055")) + of_machine_is_compatible("crystalfontz,cfa10055") || + of_machine_is_compatible("crystalfontz,cfa10057")) crystalfontz_init(); of_platform_populate(NULL, of_default_bus_match_table, -- cgit v1.2.3