From 7ec7e546c0f7facffd71bbacf6828a8d942c5f62 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Mon, 4 May 2015 22:08:47 +0200 Subject: ARM: dts: dove: Add internal i2c multiplexer node This adds a i2c-mux-pinctrl node to dove.dtsi for the internal i2c mux found on Dove SoCs. Up to now, we had no board using any of the two additional i2c busses, so make sure the change does not break any existing boards. Therefore, we rename the i2c-controller node label to "i2c" and enable it by default. Also, the dedicated sub-bus (now "i2c0") is enabled by default. The two optional sub-busses require additional external pin-muxing, so disable them by default. Signed-off-by: Sebastian Hesselbarth Acked-by: Gregory CLEMENT Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/dove.dtsi | 40 ++++++++++++++++++++++++++++++++++++++-- 1 file changed, 38 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 9ad829523a13..38b1f7e6004e 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -33,6 +33,42 @@ marvell,tauros2-cache-features = <0>; }; + i2c-mux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&i2c>; + + pinctrl-names = "i2c0", "i2c1", "i2c2"; + pinctrl-0 = <&pmx_i2cmux_0>; + pinctrl-1 = <&pmx_i2cmux_1>; + pinctrl-2 = <&pmx_i2cmux_2>; + + i2c0: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + }; + + i2c1: i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + /* Requires pmx_i2c1 on i2c controller node */ + status = "disabled"; + }; + + i2c2: i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + /* Requires pmx_i2c2 on i2c controller node */ + status = "disabled"; + }; + }; + mbus { compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus"; #address-cells = <2>; @@ -123,7 +159,7 @@ status = "disabled"; }; - i2c0: i2c-ctrl@11000 { + i2c: i2c-ctrl@11000 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11000 0x20>; #address-cells = <1>; @@ -132,7 +168,7 @@ clock-frequency = <400000>; timeout-ms = <1000>; clocks = <&core_clk 0>; - status = "disabled"; + status = "okay"; }; uart0: serial@12000 { -- cgit v1.2.3 From aa532007561e05b4dc3f60ad8eb29fa4850cab14 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Mon, 4 May 2015 22:08:48 +0200 Subject: ARM: dts: dove: Remove Compulab CM-A510 from Makefile Prior reworking Dove based Compulab CM-A510 device tree, remove it from the compiled device tree files. Signed-off-by: Sebastian Hesselbarth Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 86217db2937a..dc24597c4f2e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -649,7 +649,6 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-openblocks-ax3-4.dtb \ armada-xp-synology-ds414.dtb dtb-$(CONFIG_MACH_DOVE) += \ - dove-cm-a510.dtb \ dove-cubox.dtb \ dove-cubox-es.dtb \ dove-d2plug.dtb \ -- cgit v1.2.3 From 896dd2728ff2c85b7a1fb19b2d388deaf7e4ad0b Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Mon, 4 May 2015 22:08:49 +0200 Subject: ARM: dts: dove: Add proper support for Compulab CM-A510/SBC-A510 Existing dts file for Compulab CM-A510 was very limited due to missing hardware. Now that we actually found somebody with that board, properly rework it to provide a CoM/SoM include and a board file for Compulab's SBC-A510. Both the CM-A510 SoM and the SBC-A510 can be configured with different options, so we only enable a minimum set of options. The actual board configuration will have to be set by either the bootloader or user. Although functionally not required, repeat even disabled nodes again to increse their visibility in the dtsi/dts files. Signed-off-by: Sebastian Hesselbarth Tested-by: Gabriel Dobato Acked-by: Gregory CLEMENT Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/dove-cm-a510.dts | 38 ------- arch/arm/boot/dts/dove-cm-a510.dtsi | 195 ++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/dove-sbc-a510.dts | 182 +++++++++++++++++++++++++++++++++ 3 files changed, 377 insertions(+), 38 deletions(-) delete mode 100644 arch/arm/boot/dts/dove-cm-a510.dts create mode 100644 arch/arm/boot/dts/dove-cm-a510.dtsi create mode 100644 arch/arm/boot/dts/dove-sbc-a510.dts diff --git a/arch/arm/boot/dts/dove-cm-a510.dts b/arch/arm/boot/dts/dove-cm-a510.dts deleted file mode 100644 index 50c0d6904497..000000000000 --- a/arch/arm/boot/dts/dove-cm-a510.dts +++ /dev/null @@ -1,38 +0,0 @@ -/dts-v1/; - -#include "dove.dtsi" - -/ { - model = "Compulab CM-A510"; - compatible = "compulab,cm-a510", "marvell,dove"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x40000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - }; -}; - -&uart0 { status = "okay"; }; -&uart1 { status = "okay"; }; -&sdio0 { status = "okay"; }; -&sdio1 { status = "okay"; }; -&sata0 { status = "okay"; }; - -&spi0 { - status = "okay"; - - /* spi0.0: 4M Flash Winbond W25Q32BV */ - spi-flash@0 { - compatible = "st,w25q32"; - spi-max-frequency = <20000000>; - reg = <0>; - }; -}; - -&i2c0 { - status = "okay"; -}; diff --git a/arch/arm/boot/dts/dove-cm-a510.dtsi b/arch/arm/boot/dts/dove-cm-a510.dtsi new file mode 100644 index 000000000000..59b4056b478f --- /dev/null +++ b/arch/arm/boot/dts/dove-cm-a510.dtsi @@ -0,0 +1,195 @@ +/* + * Device Tree include for Compulab CM-A510 System-on-Module + * + * Copyright (C) 2015, Sebastian Hesselbarth + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * The CM-A510 comes with several optional components: + * + * Memory options: + * D512: 512M + * D1024: 1G + * + * NAND options: + * N512: 512M NAND + * + * Ethernet options: + * E1: PHY RTL8211D on internal GbE (SMI address 0x03) + * E2: Additional ethernet NIC RTL8111D on PCIe1 + * + * Audio options: + * A: TI TLV320AIC23b audio codec (I2C address 0x1a) + * + * Touchscreen options: + * I: TI TSC2046 touchscreen controller (on SPI1) + * + * USB options: + * U2: 2 dual-role USB2.0 ports + * U4: 2 additional USB2.0 host ports (via USB1) + * + * WiFi options: + * W: Broadcom BCM4319 802.11b/g/n (USI WM-N-BM-01 on SDIO1) + * + * GPIOs used on CM-A510: + * 1 GbE PHY reset (active low) + * 3 WakeUp + * 8 PowerOff (active low) + * 13 Touchscreen pen irq (active low) + * 65 System LED (active high) + * 69 USB Hub reset (active low) + * 70 WLAN reset (active low) + * 71 WLAN regulator (active high) + */ + +#include "dove.dtsi" + +/ { + model = "Compulab CM-A510"; + compatible = "compulab,cm-a510", "marvell,dove"; + + /* + * Set the minimum memory size here and let the + * bootloader set the real size. + */ + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + /* Set upper NAND data bit to GPO */ + pinctrl-0 = <&pmx_nand_gpo>; + pinctrl-names = "default"; + + system { + label = "cm-a510:system:green"; + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + wifi_power: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "WiFi Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +/* Optional RTL8211D GbE PHY on SMI address 0x03 */ +ðphy { + reg = <3>; + status = "disabled"; +}; + +&i2c0 { + /* Optional TI TLV320AIC23b audio codec */ + opt_audio: audio@1a { + compatible = "ti,tlv320aic23"; + reg = <0x1a>; + status = "disabled"; + }; +}; + +/* Optional RTL8111D GbE NIC on PCIe1 */ +&pcie { status = "disabled"; }; + +&pcie1 { + pinctrl-0 = <&pmx_pcie1_clkreq>; + pinctrl-names = "default"; + status = "disabled"; +}; + +&pinctrl { + pmx_uart2: pmx-uart2 { + marvell,pins = "mpp14", "mpp15"; + marvell,function = "uart2"; + }; +}; + +/* Optional Broadcom BCM4319 802.11b/g/n WiFi module */ +&sdio1 { + non-removable; + vmmc-supply = <&wifi_power>; + reset-gpio = <&gpio2 6 GPIO_ACTIVE_LOW>; + status = "disabled"; +}; + +&spi0 { + status = "okay"; + + /* 1M Flash Winbond W25Q80BL */ + flash@0 { + compatible = "winbond,w25q80"; + spi-max-frequency = <80000000>; + reg = <0>; + }; +}; + +&spi1 { + pinctrl-0 = <&pmx_spi1_20_23>; + pinctrl-names = "default"; + status = "disabled"; + + /* Optional TI TSC2046 touchscreen controller */ + opt_touch: touchscreen@0 { + compatible = "ti,tsc2046"; + spi-max-frequency = <2500000>; + reg = <0>; + pinctrl-0 = <&pmx_gpio_13>; + pinctrl-names = "default"; + interrupts-extended = <&gpio0 13 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&uart2 { + pinctrl-0 = <&pmx_uart2>; + pinctrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/dove-sbc-a510.dts b/arch/arm/boot/dts/dove-sbc-a510.dts new file mode 100644 index 000000000000..288e707dea99 --- /dev/null +++ b/arch/arm/boot/dts/dove-sbc-a510.dts @@ -0,0 +1,182 @@ +/* + * Device Tree file for Compulab SBC-A510 Single Board Computer + * + * Copyright (C) 2015, Sebastian Hesselbarth + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * SBC-A510 comprises a PCA9555 I2C GPIO expander its GPIO lines connected to + * + * 0.0 USB0 VBUS_EN (active high) + * 0.1 USB0 VBUS_GOOD + * 0.2 DVI transmitter TI TFP410 MSEN + * 0.3 DVI transmitter TI TFP410 PD# (active low power down) + * 0.4 LVDS transmitter DS90C365 PD# (active low power down) + * 0.5 LCD nRST (active low reset) + * 0.6 PCIe0 nRST (active low reset) + * 0.7 mini-PCIe slot W_DISABLE# + * + * 1.0 MMC WP + * 1.1 Camera Input FPC FLASH_STB and P21.5 + * 1.2 Camera Input FPC WE and P21.22 + * 1.3 MMC VCC_EN (active high) and P21.7 + * 1.4 Camera Input FPC AFTR_RST and P21.17 + * 1.5 Camera Input FPC OE and P21.19 + * 1.6 Camera Input FPC SNPSHT and P21.6 + * 1.7 Camera Input FPC SHTR and P21.10 + */ + +/dts-v1/; + +#include "dove-cm-a510.dtsi" + +/ { + model = "Compulab SBC-A510"; + compatible = "compulab,sbc-a510", "compulab,cm-a510", "marvell,dove"; + + chosen { + stdout-path = &uart0; + }; + + regulators { + usb0_power: regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>; + }; + + mmc_power: regulator@3 { + compatible = "regulator-fixed"; + regulator-name = "MMC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +/* Ethernet0 depends on CM-A510 option E1 */ +&mdio { status = "disabled"; }; +ð { status = "disabled"; }; +ðphy { status = "disabled"; }; + +/* + * USB port 0 can be powered and monitored by I2C GPIO expander: + * VBUS_ENABLE on GPIO0, VBUS_GOOD on GPIO1 + */ +&ehci0 { + status = "okay"; + vbus-supply = <&usb0_power>; +}; + +/* USB port 1 (and ports 2, 3 if CM-A510 has U4 option) */ +&ehci1 { status = "okay"; }; + +/* + * I2C bus layout: + * i2c0: + * - Audio Codec, 0x1a (option from CM-A510) + * - DVI transmitter TI TFP410, 0x39 + * - HDMI/DVI DDC channel + * i2c1: + * - GPIO expander, NXP PCA9555, 0x20 + * - VGA DDC channel + */ +&i2c { + pinctrl-0 = <&pmx_i2c1>; + pinctrl-names = "default"; +}; + +&i2c0 { + /* TI TFP410 DVI transmitter */ + dvi: video@39 { + compatible = "ti,tfp410"; + reg = <0x39>; + powerdown-gpio = <&gpio_ext 3 GPIO_ACTIVE_LOW>; + }; +}; + +&i2c1 { + status = "okay"; + + /* NXP PCA9555 GPIO expander */ + gpio_ext: gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + #gpio-cells = <2>; + }; +}; + +&pcie { status = "okay"; }; + +/* + * PCIe0 can be configured by Jumper E1 to be either connected to + * a mini-PCIe slot or a Pericom PI7C9X111 PCIe-to-PCI bridge. + */ +&pcie0 { + status = "okay"; + pinctrl-0 = <&pmx_pcie0_clkreq>; + pinctrl-names = "default"; + reset-gpios = <&gpio_ext 6 GPIO_ACTIVE_LOW>; +}; + +/* Ethernet1 depends on CM-A510 option E2 */ +&pcie1 { status = "disabled"; }; + +/* SATA connector */ +&sata0 { status = "okay"; }; + +/* + * SDIO0 is connected to a MMC/SD/SDIO socket, I2C GPIO expander has + * VCC_MMC_ENABLE on GPIO13, MMC_WP on GPIO10 + */ +&sdio0 { + vmmc-supply = <&mmc_power>; + wp-gpios = <&gpio_ext 10 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +/* UART0 on RS232 mini-connector */ +&uart0 { status = "okay"; }; +/* UART2 on pin headers */ +&uart2 { status = "okay"; }; -- cgit v1.2.3 From 1c1534d94288a51c47823bcd7e06f82fda521a97 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Mon, 4 May 2015 22:08:50 +0200 Subject: ARM: dts: dove: Add Compulab SBC-A510 to Makefile With reworked device tree files for Compulab CM-A510 SoM and SBC-A510 base board, now add the correspoding board file to Makefile again. Signed-off-by: Sebastian Hesselbarth Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index dc24597c4f2e..ba72134f1fd3 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -653,7 +653,8 @@ dtb-$(CONFIG_MACH_DOVE) += \ dove-cubox-es.dtb \ dove-d2plug.dtb \ dove-d3plug.dtb \ - dove-dove-db.dtb + dove-dove-db.dtb \ + dove-sbc-a510.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += \ mt6589-aquaris5.dtb \ mt6592-evb.dtb \ -- cgit v1.2.3 From 973ed08377f6d61dd4e9fd62207737c8ec0d49e9 Mon Sep 17 00:00:00 2001 From: Imre Kaloz Date: Wed, 6 May 2015 15:13:59 +0200 Subject: ARM: mvebu: add alias for mdio on Armada 38x This allows us to reference it later. Signed-off-by: Imre Kaloz --- arch/arm/boot/dts/armada-38x.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index ed2dd8ba4080..839e5bfc13c3 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -495,7 +495,7 @@ status = "disabled"; }; - mdio@72004 { + mdio: mdio@72004 { #address-cells = <1>; #size-cells = <0>; compatible = "marvell,orion-mdio"; -- cgit v1.2.3