| Age | Commit message (Collapse) | Author |
|---|
|
hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.
Fixes: 3c857757ef6e ("Bluetooth: Add directed advertising support through connect()")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When an Advertisement Monitor is configured with SamplingPeriod 0xFF,
the controller reports only one adv report along with the MSFT Monitor
Device event.
When an advertiser matches multiple monitors, some controllers send one
adv report for each matched monitor; whereas, some controllers send just
one adv report for all matched monitors.
In such a case, report Adv Monitor Device Found event for each matched
monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Clear already tracked devices on system resume. Once the monitors are
reregistered after resume, matched devices in range will be found again.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Callers pass msg->msg_flags as flags, which contains MSG_DONTWAIT
instead of O_NONBLOCK.
Signed-off-by: Gavin Li <gavin@matician.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
data.pid is set twice with the same value. Remove one of these redundant
calls.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This fixes the following trace caused by receiving
HCI_EV_DISCONN_PHY_LINK_COMPLETE which does call hci_conn_del without
first checking if conn->type is in fact AMP_LINK and in case it is
do properly cleanup upper layers with hci_disconn_cfm:
==================================================================
BUG: KASAN: use-after-free in hci_send_acl+0xaba/0xc50
Read of size 8 at addr ffff88800e404818 by task bluetoothd/142
CPU: 0 PID: 142 Comm: bluetoothd Not tainted
5.17.0-rc5-00006-gda4022eeac1a #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x1f/0x150
kasan_report.cold+0x7f/0x11b
hci_send_acl+0xaba/0xc50
l2cap_do_send+0x23f/0x3d0
l2cap_chan_send+0xc06/0x2cc0
l2cap_sock_sendmsg+0x201/0x2b0
sock_sendmsg+0xdc/0x110
sock_write_iter+0x20f/0x370
do_iter_readv_writev+0x343/0x690
do_iter_write+0x132/0x640
vfs_writev+0x198/0x570
do_writev+0x202/0x280
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RSP: 002b:00007ffce8a099b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3
0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 14 00 00 00 0f 05
<48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
RDX: 0000000000000001 RSI: 00007ffce8a099e0 RDI: 0000000000000015
RAX: ffffffffffffffda RBX: 00007ffce8a099e0 RCX: 00007f788fc3cf77
R10: 00007ffce8af7080 R11: 0000000000000246 R12: 000055e4ccf75580
RBP: 0000000000000015 R08: 0000000000000002 R09: 0000000000000001
</TASK>
R13: 000055e4ccf754a0 R14: 000055e4ccf75cd0 R15: 000055e4ccf4a6b0
Allocated by task 45:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
hci_chan_create+0x9a/0x2f0
l2cap_conn_add.part.0+0x1a/0xdc0
l2cap_connect_cfm+0x236/0x1000
le_conn_complete_evt+0x15a7/0x1db0
hci_le_conn_complete_evt+0x226/0x2c0
hci_le_meta_evt+0x247/0x450
hci_event_packet+0x61b/0xe90
hci_rx_work+0x4d5/0xc50
process_one_work+0x8fb/0x15a0
worker_thread+0x576/0x1240
kthread+0x29d/0x340
ret_from_fork+0x1f/0x30
Freed by task 45:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0xfb/0x130
kfree+0xac/0x350
hci_conn_cleanup+0x101/0x6a0
hci_conn_del+0x27e/0x6c0
hci_disconn_phylink_complete_evt+0xe0/0x120
hci_event_packet+0x812/0xe90
hci_rx_work+0x4d5/0xc50
process_one_work+0x8fb/0x15a0
worker_thread+0x576/0x1240
kthread+0x29d/0x340
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff88800c0f0500
The buggy address is located 24 bytes inside of
which belongs to the cache kmalloc-128 of size 128
The buggy address belongs to the page:
128-byte region [ffff88800c0f0500, ffff88800c0f0580)
flags: 0x100000000000200(slab|node=0|zone=1)
page:00000000fe45cd86 refcount:1 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0xc0f0
raw: 0000000000000000 0000000080100010 00000001ffffffff
0000000000000000
raw: 0100000000000200 ffffea00003a2c80 dead000000000004
ffff8880078418c0
page dumped because: kasan: bad access detected
ffff88800c0f0400: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
Memory state around the buggy address:
>ffff88800c0f0500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88800c0f0480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88800c0f0580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
==================================================================
ffff88800c0f0600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Reported-by: Sönke Huster <soenke.huster@eknoes.de>
Tested-by: Sönke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some controllers have problems with being sent a command to clear
all filtering. While the HCI code does not unconditionally
send a clear-all anymore at BR/EDR setup (after the state machine
refactor), there might be more ways of hitting these codepaths
in the future as the kernel develops.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Variable cur_len is being ininitialized with a value in the start of
a for-loop but this is never read, it is being re-assigned a new value
on the first statement in the for-loop. The initialization is redundant
and can be removed.
Cleans up clang scan build warning:
net/bluetooth/mgmt.c:7958:14: warning: Although the value stored to 'cur_len'
is used in the enclosing expression, the value is never actually read
from 'cur_len' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.18
Third set of patches for v5.18. Smaller set this time, support for
mt7921u and some work on MBSSID support. Also a workaround for rfkill
userspace event.
Major changes:
mac80211
* MBSSID beacon handling in AP mode
rfkill
* make new event layout opt-in to workaround buggy user space
rtlwifi
* support On Networks N150 device id
mt76
* mt7915: MBSSID and 6 GHz band support
* new driver mt7921u
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Again new complaints surfaced that we had broken the ABI here,
although previously all the userspace tools had agreed that it
was their mistake and fixed it. Yet now there are cases (e.g.
RHEL) that want to run old userspace with newer kernels, and
thus are broken.
Since this is a bit of a whack-a-mole thing, change the whole
extensibility scheme of rfkill to no longer just rely on the
message lengths, but instead require userspace to opt in via a
new ioctl to a given maximum event size that it is willing to
understand.
By default, set that to RFKILL_EVENT_SIZE_V1 (8), so that the
behaviour for userspace not calling the ioctl will look as if
it's just running on an older kernel.
Fixes: 14486c82612a ("rfkill: add a reason to the HW rfkill state")
Cc: stable@vger.kernel.org # 5.11+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316212749.16491491b270.Ifcb1950998330a596f29a2a162e00b7546a1d6d0@changeid
|
|
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for MST state changes.
When a state changes to disabled/blocking/listening, make sure to fast
age any dynamic entries in the affected VLANs (those controlled by the
MSTI in question).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the usual trampoline functionality from the generic DSA layer down
to the drivers for VLAN MSTI migrations.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When joining a bridge where MST is enabled, we validate that the
proper offloading support is in place, otherwise we fallback to
software bridging.
When then mode is changed on a bridge in which we are members, we
refuse the change if offloading is not supported.
At the moment we only check for configurable learning, but this will
be further restricted as we support more MST related switchdev events.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is useful for switchdev drivers who are offloading MST states
into hardware. As an example, a driver may wish to flush the FDB for a
port when it transitions from forwarding to blocking - which means
that the previous state must be discoverable.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is useful for switchdev drivers that might want to refuse to join
a bridge where MST is enabled, if the hardware can't support it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
br_mst_get_info answers the question: "On this bridge, which VIDs are
mapped to the given MSTI?"
This is useful in switchdev drivers, which might have to fan-out
operations, relating to an MSTI, per VLAN.
An example: When a port's MST state changes from forwarding to
blocking, a driver may choose to flush the dynamic FDB entries on that
port to get faster reconvergence of the network, but this should only
be done in the VLANs that are managed by the MSTI in question.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When compiling with -Wformat, clang emits the following warning:
net/8021q/vlanproc.c:284:22: warning: format specifies type 'unsigned
short' but the argument has type 'int' [-Wformat]
mp->priority, ((mp->vlan_qos >> 13) & 0x7));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <morbo@google.com>
Link: https://lore.kernel.org/r/20220316213125.2353370-1-morbo@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c2d ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a port joins a bridge that it can't offload, it will fallback to
standalone mode and software bridging. In this case, we never want to
offload any FDB entries to hardware either.
Previously, for host addresses, we would eventually end up in
dsa_port_bridge_host_fdb_add, which would unconditionally dereference
dp->bridge and cause a segfault.
Fixes: c26933639b54 ("net: dsa: request drivers to perform FDB isolation")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220315233033.1468071-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-03-16
the first 3 patches are by Oliver Hartkopp target the CAN ISOTP
protocol and fix a problem found by syzbot in isotp_bind(), return
-EADDRNOTAVAIL in unbound sockets in isotp_recvmsg() and add support
for MSG_TRUNC to isotp_recvmsg().
Amit Kumar Mahapatra converts the xilinx,can device tree bindings to
yaml.
The last patch is by Julia Lawall and fixes typos in the ucan driver.
* tag 'linux-can-next-for-5.18-20220316' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ucan: fix typos in comments
dt-bindings: can: xilinx_can: Convert Xilinx CAN binding to YAML
can: isotp: support MSG_TRUNC flag when reading from socket
can: isotp: return -EADDRNOTAVAIL when reading from unbound socket
can: isotp: sanitize CAN ID checks in isotp_bind()
====================
Link: https://lore.kernel.org/r/20220316204710.716341-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When providing the MSG_TRUNC flag via recvmsg() syscall the return value
provides the real length of the packet or datagram, even when it was longer
than the passed buffer.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://github.com/linux-can/can-utils/issues/347#issuecomment-1065932671
Link: https://lore.kernel.org/all/20220316164258.54155-3-socketcan@hartkopp.net
Suggested-by: Derek Will <derekrobertwill@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When reading from an unbound can-isotp socket the syscall blocked
indefinitely. As unbound sockets (without given CAN address information)
do not make sense anyway we directly return -EADDRNOTAVAIL on read()
analogue to the known behavior from sendmsg().
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://github.com/linux-can/can-utils/issues/349
Link: https://lore.kernel.org/all/20220316164258.54155-2-socketcan@hartkopp.net
Suggested-by: Derek Will <derekrobertwill@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Syzbot created an environment that lead to a state machine status that
can not be reached with a compliant CAN ID address configuration.
The provided address information consisted of CAN ID 0x6000001 and 0xC28001
which both boil down to 11 bit CAN IDs 0x001 in sending and receiving.
Sanitize the SFF/EFF CAN ID values before performing the address checks.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/20220316164258.54155-1-socketcan@hartkopp.net
Reported-by: syzbot+2339c27f5c66c652843e@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Now that devlink ports are protected by the instance lock
it seems natural to pass devlink_port as an argument to
the port_split / port_unsplit callbacks.
This should save the drivers from doing a lookup.
In theory drivers may have supported unsplitting ports
which were not registered prior to this change.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Let the core take the devlink instance lock around port splitting
and remove the now redundant locking in the drivers.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It should be familiar and beneficial to expose devlink instance
lock to the drivers. This way drivers can block devlink from
calling them during critical sections without breakneck locking.
Add port helpers, port splitting callbacks will be the first
target.
Use 'devl_' prefix for "explicitly locked" API. Initial RFC used
'__devlink' but that's too much typing.
devl_lock_is_held() is not defined without lockdep, which is
the same behavior as lockdep_is_held() itself.
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2022-03-16
1) Fix a kernel-info-leak in pfkey.
From Haimin Zhang.
2) Fix an incorrect check of the return value of ipv6_skip_exthdr.
From Sabrina Dubroca.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
esp6: fix check on ipv6_skip_exthdr's return value
af_key: add __GFP_ZERO flag for compose_sadb_supported in function pfkey_register
====================
Link: https://lore.kernel.org/r/20220316121142.3142336-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fundamental premise of VRF and l3mdev core code is binding a socket
to a device (l3mdev or netdev with an L3 domain) to indicate L3 scope.
Legacy code resets flowi_oif to the l3mdev losing any original port
device binding. Ben (among others) has demonstrated use cases where the
original port device binding is important and needs to be retained.
This patch handles that by adding a new entry to the common flow struct
that can indicate the l3mdev index for later rule and table matching
avoiding the need to reset flowi_oif.
In addition to allowing more use cases that require port device binds,
this patch brings a few datapath simplications:
1. l3mdev_fib_rule_match is only called when walking fib rules and
always after l3mdev_update_flow. That allows an optimization to bail
early for non-VRF type uses cases when flowi_l3mdev is not set. Also,
only that index needs to be checked for the FIB table id.
2. l3mdev_update_flow can be called with flowi_oif set to a l3mdev
(e.g., VRF) device. By resetting flowi_oif only for this case the
FLOWI_FLAG_SKIP_NH_OIF flag is not longer needed and can be removed,
removing several checks in the datapath. The flowi_iif path can be
simplified to only be called if the it is not loopback (loopback can
not be assigned to an L3 domain) and the l3mdev index is not already
set.
3. Avoid another device lookup in the output path when the fib lookup
returns a reject failure.
Note: 2 functional tests for local traffic with reject fib rules are
updated to reflect the new direct failure at FIB lookup time for ping
rather than the failure on packet path. The current code fails like this:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: Warning: source address might be selected on device other than: eth1
PING 172.16.3.1 (172.16.3.1) from 172.16.3.1 eth1: 56(84) bytes of data.
--- 172.16.3.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
where the test now directly fails:
HINT: Fails since address on vrf device is out of device scope
COMMAND: ip netns exec ns-A ping -c1 -w1 -I eth1 172.16.3.1
ping: connect: No route to host
Signed-off-by: David Ahern <dsahern@kernel.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220314204551.16369-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Revert CHECKSUM_UNNECESSARY for UDP packet from conntrack.
2) Reject unsupported families when creating tables, from Phil Sutter.
3) GRE support for the flowtable, from Toshiaki Makita.
4) Add GRE offload support for act_ct, also from Toshiaki.
5) Update mlx5 driver to support for GRE flowtable offload,
from Toshiaki Makita.
6) Oneliner to clean up incorrect indentation in nf_conntrack_bridge,
from Jiapeng Chong.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: bridge: clean up some inconsistent indenting
net/mlx5: Support GRE conntrack offload
act_ct: Support GRE offload
netfilter: flowtable: Support GRE
netfilter: nf_tables: Reject tables of unsupported family
Revert "netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY"
====================
Link: https://lore.kernel.org/r/20220315091513.66544-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update bssid_indicator in ieee80211_bss_conf according to the
number of bssid in the set.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/f92317e002fca9933f05a445fcefb4f53291d601.1645702516.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Trigger ieee80211_csa_finish() on the non-transmitting interfaces
when channel switch concludes on the transmitting interface.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/6fde4d7f9fa387494f46a7aa4a584478dcda06f1.1645702516.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add new fields in struct beacon_data to store all MBSSID elements.
Generate a beacon template which includes all MBSSID elements.
Move CSA offset to reflect the MBSSID element length.
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Money Wang <money.wang@mediatek.com>
Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org
[small cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When CONFIG_PM isn't defined we don't have the function
ieee80211_sta_restart() compiled in, but we always need
it now for firmware restart. Move it out of the ifdef.
Fixes: 7d352ccf1e99 ("mac80211: Add support to trigger sta disconnect on hardware restart")
Link: https://lore.kernel.org/r/20220312221957.1fa96c72db51.I8ecaa5f9402fede0272161e0531ab930b97fba3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
syzbot found that when an AF_PACKET socket is using PACKET_COPY_THRESH
and mmap operations, tpacket_rcv() is queueing skbs with
garbage in skb->cb[], triggering a too big copy [1]
Presumably, users of af_packet using mmap() already gets correct
metadata from the mapped buffer, we can simply make sure
to clear 12 bytes that might be copied to user space later.
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: stack-out-of-bounds in packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
Write of size 165 at addr ffffc9000385fb78 by task syz-executor233/3631
CPU: 0 PID: 3631 Comm: syz-executor233 Not tainted 5.17.0-rc7-syzkaller-02396-g0b3660695e80 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0xf/0x336 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0x13d/0x180 mm/kasan/generic.c:189
memcpy+0x39/0x60 mm/kasan/shadow.c:66
memcpy include/linux/fortify-string.h:225 [inline]
packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_recvmsg net/socket.c:962 [inline]
____sys_recvmsg+0x2c4/0x600 net/socket.c:2632
___sys_recvmsg+0x127/0x200 net/socket.c:2674
__sys_recvmsg+0xe2/0x1a0 net/socket.c:2704
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fdfd5954c29
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 41 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffcf8e71e48 EFLAGS: 00000246 ORIG_RAX: 000000000000002f
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fdfd5954c29
RDX: 0000000000000000 RSI: 0000000020000500 RDI: 0000000000000005
RBP: 0000000000000000 R08: 000000000000000d R09: 000000000000000d
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffcf8e71e60
R13: 00000000000f4240 R14: 000000000000c1ff R15: 00007ffcf8e71e54
</TASK>
addr ffffc9000385fb78 is located in stack of task syz-executor233/3631 at offset 32 in frame:
____sys_recvmsg+0x0/0x600 include/linux/uio.h:246
this frame has 1 object:
[32, 160) 'addr'
Memory state around the buggy address:
ffffc9000385fa80: 00 04 f3 f3 f3 f3 f3 00 00 00 00 00 00 00 00 00
ffffc9000385fb00: 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00
>ffffc9000385fb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f3
^
ffffc9000385fc00: f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 f1
ffffc9000385fc80: f1 f1 f1 00 f2 f2 f2 00 f2 f2 f2 00 00 00 00 00
==================================================================
Fixes: 0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220312232958.3535620-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net coming late
in the 5.17-rc process:
1) Revert port remap to mitigate shadowing service ports, this is causing
problems in existing setups and this mitigation can be achieved with
explicit ruleset, eg.
... tcp sport < 16386 tcp dport >= 32768 masquerade random
This patches provided a built-in policy similar to the one described above.
2) Disable register tracking infrastructure in nf_tables. Florian reported
two issues:
- Existing expressions with no implemented .reduce interface
that causes data-store on register should cancel the tracking.
- Register clobbering might be possible storing data on registers that
are larger than 32-bits.
This might lead to generating incorrect ruleset bytecode. These two
issues are scheduled to be addressed in the next release cycle.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable register tracking
Revert "netfilter: conntrack: tag conntracks picked up in local out hook"
Revert "netfilter: nat: force port remap to prevent shadowing well-known ports"
====================
Link: https://lore.kernel.org/r/20220312220315.64531-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr")
introduced an incorrect check, which leads to all ESP packets over
either TCPv6 or UDPv6 encapsulation being dropped. In this particular
case, offset is negative, since skb->data points to the ESP header in
the following chain of headers, while skb->network_header points to
the IPv6 header:
IPv6 | ext | ... | ext | UDP | ESP | ...
That doesn't seem to be a problem, especially considering that if we
reach esp6_input_done2, we're guaranteed to have a full set of headers
available (otherwise the packet would have been dropped earlier in the
stack). However, it means that the return value will (intentionally)
be negative. We can make the test more specific, as the expected
return value of ipv6_skip_exthdr will be the (negated) size of either
a UDP header, or a TCP header with possible options.
In the future, we should probably either make ipv6_skip_exthdr
explicitly accept negative offsets (and adjust its return value for
error cases), or make ipv6_skip_exthdr only take non-negative
offsets (and audit all callers).
Fixes: 5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the
Application Priority Table to define QoS classes (0 to 7) per IP DSCP
value (0 to 63).
In the absence of an app table entry for a packet with DSCP value X,
QoS classification for that packet falls back to other methods (VLAN PCP
or port-based default). The presence of an app table for DSCP value X
with priority Y makes the hardware classify the packet to QoS class Y.
As opposed to the default-prio where DSA exposes only a "set" in
dsa_switch_ops (because the port-based default is the fallback, it
always exists, either implicitly or explicitly), for DSCP priorities we
expose an "add" and a "del". The addition of a DSCP entry means trusting
that DSCP priority, the deletion means ignoring it.
Drivers that already trust (at least some) DSCP values can describe
their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is
called for each DSCP value from 0 to 63.
Again, there can be more than one dcbnl app table entry for the same
DSCP value, DSA chooses the one with the largest configured priority.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port-based default QoS class is assigned to packets that lack a
VLAN PCP (or the port is configured to not trust the VLAN PCP),
an IP DSCP (or the port is configured to not trust IP DSCP), and packets
on which no tc-skbedit action has matched.
Similar to other drivers, this can be exposed to user space using the
DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table
D-8 - Sel field values that when the Selector is 1, the Protocol ID
value of 0 denotes the "Default application priority. For use when
application priority is not otherwise specified."
The way in which the dcbnl integration in DSA has been designed has to
do with its requirements. Andrew Lunn explains that SOHO switches are
expected to come with some sort of pre-configured QoS profile, and that
it is desirable for this to come pre-loaded into the DSA slave interfaces'
DCB application priority table.
In the dcbnl design, this is possible because calls to dcb_ieee_setapp()
can be initiated by anyone including being self-initiated by this device
driver.
However, what makes this challenging to implement in DSA is that the DSA
core manages the net_devices (effectively hiding them from drivers),
while drivers manage the hardware. The DSA core has no knowledge of what
individual drivers' QoS policies are. DSA could export to drivers a
wrapper over dcb_ieee_setapp() and these could call that function to
pre-populate the app priority table, however drivers don't have a good
moment in time to do this. The dsa_switch_ops :: setup() method gets
called before the net_devices are created (dsa_slave_create), and so is
dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops ::
port_enable(), but this gets called upon each ndo_open. If we add app
table entries on every open, we'd need to remove them on close, to avoid
duplicate entry errors. But if we delete app priority entries on close,
what we delete may not be the initial, driver pre-populated entries, but
rather user-added entries.
So it is clear that letting drivers choose the timing of the
dcb_ieee_setapp() call is inappropriate. The alternative which was
chosen is to introduce hardware-specific ops in dsa_switch_ops, and
effectively hide dcbnl details from drivers as well. For pre-populating
the application table, dsa_slave_dcbnl_init() will call
ds->ops->port_get_default_prio() which is supposed to read from
hardware. If the operation succeeds, DSA creates a default-prio app
table entry. The method is called as soon as the slave_dev is
registered, but before we release the rtnl_mutex. This is done such that
user space sees the app table entries as soon as it sees the interface
being registered.
The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer
changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to
return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is
NULL. Because there are still dcbnl-unaware DSA drivers even if they
have dcbnl_ops populated, the way to restore the behavior is to make all
dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific
dsa_switch_ops method.
The dcbnl framework absurdly allows there to be more than one app table
entry for the same selector and protocol (in other words, more than one
port-based default priority). In the iproute2 dcb program, there is a
"replace" syntactical sugar command which performs an "add" and a "del"
to hide this away. But we choose the largest configured priority when we
call ds->ops->port_set_default_prio(), using __fls(). When there is no
default-prio app table entry left, the port-default priority is restored
to 0.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
____napi_schedule() needs to be invoked with disabled interrupts due to
__raise_softirq_irqoff (in order not to corrupt the per-CPU list).
____napi_schedule() needs also to be invoked from an interrupt context
so that the raised-softirq is processed while the interrupt context is
left.
Add lockdep asserts for both conditions.
While this is the second time the irq/softirq check is needed, provide a
generic lockdep_assert_softirq_will_run() which is used by both caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register tracking infrastructure is incomplete, it might lead to
generating incorrect ruleset bytecode, disable it by now given we are
late in the release process.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: GTP support in switchdev
Marcin Szycik says:
Add support for adding GTP-C and GTP-U filters in switchdev mode.
To create a filter for GTP, create a GTP-type netdev with ip tool, enable
hardware offload, add qdisc and add a filter in tc:
ip link add $GTP0 type gtp role <sgsn/ggsn> hsize <hsize>
ethtool -K $PF0 hw-tc-offload on
tc qdisc add dev $GTP0 ingress
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
action mirred egress redirect dev $VF1_PR
By default, a filter for GTP-U will be added. To add a filter for GTP-C,
specify enc_dst_port = 2123, e.g.:
tc filter add dev $GTP0 ingress prio 1 flower enc_key_id 1337 \
enc_dst_port 2123 action mirred egress redirect dev $VF1_PR
Note: outer IPv6 offload is not supported yet.
Note: GTP-U with no payload offload is not supported yet.
ICE COMMS package is required to create a filter as it contains GTP
profiles.
Changes in iproute2 [1] are required to be able to add GTP netdev and use
GTP-specific options (QFI and PDU type).
[1] https://lore.kernel.org/netdev/20220211182902.11542-1-wojciech.drewek@intel.com/T
---
v2: Add more CC
v3: Fix mail thread, sorry for spam
v4: Add GTP echo response in gtp module
v5: Change patch order
v6: Add GTP echo request in gtp module
v7: Fix kernel-docs in ice
v8: Remove handling of GTP Echo Response
v9: Add sending of multicast message on GTP Echo Response, fix GTP-C dummy
packet selection
v10: Rebase, fixed most 80 char line limits
v11: Rebase, collect Harald's Reviewed-by on patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
