| Age | Commit message (Collapse) | Author |
|---|
|
Function 'mctp_dev_get_rtnl' is declared twice, so remove the
repeated declaration.
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduced in commit 38b5beeae7a4 ("net: dsa: sja1105: prepare tagger
for handling DSA tags and VLAN simultaneously"), the sja1105_xmit_tpid
function solved quite a different problem than our needs are now.
Then, we used best-effort VLAN filtering and we were using the xmit_tpid
to tunnel packets coming from an 8021q upper through the TX VLAN allocated
by tag_8021q to that egress port. The need for a different VLAN protocol
depending on switch revision came from the fact that this in itself was
more of a hack to trick the hardware into accepting tunneled VLANs in
the first place.
Right now, we deny 8021q uppers (see sja1105_prechangeupper). Even if we
supported them again, we would not do that using the same method of
{tunneling the VLAN on egress, retagging the VLAN on ingress} that we
had in the best-effort VLAN filtering mode. It seems rather simpler that
we just allocate a VLAN in the VLAN table that is simply not used by the
bridge at all, or by any other port.
Anyway, I have 2 gripes with the current sja1105_xmit_tpid:
1. When sending packets on behalf of a VLAN-aware bridge (with the new
TX forwarding offload framework) plus untagged (with the tag_8021q
VLAN added by the tagger) packets, we can see that on SJA1105P/Q/R/S
and later (which have a qinq_tpid of ETH_P_8021AD), some packets sent
through the DSA master have a VLAN protocol of 0x8100 and others of
0x88a8. This is strange and there is no reason for it now. If we have
a bridge and are therefore forced to send using that bridge's TPID,
we can as well blend with that bridge's VLAN protocol for all packets.
2. The sja1105_xmit_tpid introduces a dependency on the sja1105 driver,
because it looks inside dp->priv. It is desirable to keep as much
separation between taggers and switch drivers as possible. Now it
doesn't do that anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105 driver is a bit special in its use of VLAN headers as DSA
tags. This is because in VLAN-aware mode, the VLAN headers use an actual
TPID of 0x8100, which is understood even by the DSA master as an actual
VLAN header.
Furthermore, control packets such as PTP and STP are transmitted with no
VLAN header as a DSA tag, because, depending on switch generation, there
are ways to steer these control packets towards a precise egress port
other than VLAN tags. Transmitting control packets as untagged means
leaving a door open for traffic in general to be transmitted as untagged
from the DSA master, and for it to traverse the switch and exit a random
switch port according to the FDB lookup.
This behavior is a bit out of line with other DSA drivers which have
native support for DSA tagging. There, it is to be expected that the
switch only accepts DSA-tagged packets on its CPU port, dropping
everything that does not match this pattern.
We perhaps rely a bit too much on the switches' hardware dropping on the
CPU port, and place no other restrictions in the kernel data path to
avoid that. For example, sja1105 is also a bit special in that STP/PTP
packets are transmitted using "management routes"
(sja1105_port_deferred_xmit): when sending a link-local packet from the
CPU, we must first write a SPI message to the switch to tell it to
expect a packet towards multicast MAC DA 01-80-c2-00-00-0e, and to route
it towards port 3 when it gets it. This entry expires as soon as it
matches a packet received by the switch, and it needs to be reinstalled
for the next packet etc. All in all quite a ghetto mechanism, but it is
all that the sja1105 switches offer for injecting a control packet.
The driver takes a mutex for serializing control packets and making the
pairs of SPI writes of a management route and its associated skb atomic,
but to be honest, a mutex is only relevant as long as all parties agree
to take it. With the DSA design, it is possible to open an AF_PACKET
socket on the DSA master net device, and blast packets towards
01-80-c2-00-00-0e, and whatever locking the DSA switch driver might use,
it all goes kaput because management routes installed by the driver will
match skbs sent by the DSA master, and not skbs generated by the driver
itself. So they will end up being routed on the wrong port.
So through the lens of that, maybe it would make sense to avoid that
from happening by doing something in the network stack, like: introduce
a new bit in struct sk_buff, like xmit_from_dsa. Then, somewhere around
dev_hard_start_xmit(), introduce the following check:
if (netdev_uses_dsa(dev) && !skb->xmit_from_dsa)
kfree_skb(skb);
Ok, maybe that is a bit drastic, but that would at least prevent a bunch
of problems. For example, right now, even though the majority of DSA
switches drop packets without DSA tags sent by the DSA master (and
therefore the majority of garbage that user space daemons like avahi and
udhcpcd and friends create), it is still conceivable that an aggressive
user space program can open an AF_PACKET socket and inject a spoofed DSA
tag directly on the DSA master. We have no protection against that; the
packet will be understood by the switch and be routed wherever user
space says. Furthermore: there are some DSA switches where we even have
register access over Ethernet, using DSA tags. So even user space
drivers are possible in this way. This is a huge hole.
However, the biggest thing that bothers me is that udhcpcd attempts to
ask for an IP address on all interfaces by default, and with sja1105, it
will attempt to get a valid IP address on both the DSA master as well as
on sja1105 switch ports themselves. So with IP addresses in the same
subnet on multiple interfaces, the routing table will be messed up and
the system will be unusable for traffic until it is configured manually
to not ask for an IP address on the DSA master itself.
It turns out that it is possible to avoid that in the sja1105 driver, at
least very superficially, by requesting the switch to drop VLAN-untagged
packets on the CPU port. With the exception of control packets, all
traffic originated from tag_sja1105.c is already VLAN-tagged, so only
STP and PTP packets need to be converted. For that, we need to uphold
the equivalence between an untagged and a pvid-tagged packet, and to
remember that the CPU port of sja1105 uses a pvid of 4095.
Now that we drop untagged traffic on the CPU port, non-aggressive user
space applications like udhcpcd stop bothering us, and sja1105 effectively
becomes just as vulnerable to the aggressive kind of user space programs
as other DSA switches are (ok, users can also create 8021q uppers on top
of the DSA master in the case of sja1105, but in future patches we can
easily deny that, but it still doesn't change the fact that VLAN-tagged
packets can still be injected over raw sockets).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added the MP_FAIL suboption sending support.
Add a new flag named send_mp_fail in struct mptcp_subflow_context. If
this flag is set, send out MP_FAIL suboption.
Add a new member fail_seq in struct mptcp_out_options to save the data
sequence number to put into the MP_FAIL suboption.
An MP_FAIL option could be included in a RST or on the subflow-level
ACK.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous patch we can alias with a union several
fields in mptcp_out_options. Such struct is stack allocated and
memset() for each plain TCP out packet. Every saved byted counts.
Before:
pahole -EC mptcp_out_options
# ...
/* size: 136, cachelines: 3, members: 17 */
After:
pahole -EC mptcp_out_options
# ...
/* size: 56, cachelines: 1, members: 9 */
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-08-24
Vinicius Costa Gomes says:
This adds support for PCIe PTM (Precision Time Measurement) to the igc
driver. PCIe PTM allows the NIC and Host clocks to be compared more
precisely, improving the clock synchronization accuracy.
Patch 1/4 reverts a commit that made pci_enable_ptm() private to the
PCI subsystem, reverting makes it possible for it to be called from
the drivers.
Patch 2/4 adds the pcie_ptm_enabled() helper.
Patch 3/4 calls pci_enable_ptm() from the igc driver.
Patch 4/4 implements the PCIe PTM support. Exposing it via the
.getcrosststamp() API implies that the time measurements are made
synchronously with the ioctl(). The hardware was implemented so the
most convenient way to retrieve that information would be
asynchronously. So, to follow the expectations of the ioctl() we have
to use less convenient ways, triggering an PCIe PTM dialog every time
a ioctl() is received.
Some questions are raised (also pointed out in the commit message):
1. Using convert_art_ns_to_tsc() is too x86 specific, there should be
a common way to create a 'system_counterval_t' from a timestamp.
2. convert_art_ns_to_tsc() says that it should only be used when
X86_FEATURE_TSC_KNOWN_FREQ is true, but during tests it works even
when it returns false. Should that check be done?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
performance of changing link state, attaching a VRF, changing an IPv6 address, etc. go down dramtically.
The source of most of the slow down is the `dev_addr_lists.c` module,
which mainatins a linked list of HW addresses.
When using IPv6, this list grows for each IPv6 address added on a
VLAN, since each IPv6 address has a multicast HW address associated with
it.
When performing any modification to the involved links, this list is
traversed many times, often for nothing, all while holding the RTNL
lock.
Instead, this patch adds an auxilliary rbtree which cuts down
traversal time significantly.
Performance can be seen with the following script:
#!/bin/bash
ip netns del test || true 2>/dev/null
ip netns add test
echo 1 | ip netns exec test tee /proc/sys/net/ipv6/conf/all/keep_addr_on_down > /dev/null
set -e
ip -n test link add foo type veth peer name bar
ip -n test link add b1 type bond
ip -n test link add florp type vrf table 10
ip -n test link set bar master b1
ip -n test link set foo up
ip -n test link set bar up
ip -n test link set b1 up
ip -n test link set florp up
VLAN_COUNT=1500
BASE_DEV=b1
echo Creating vlans
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link add link $BASE_DEV name foo.\$i type vlan id \$i; done"
echo Bringing them up
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link set foo.\$i up; done"
echo Assiging IPv6 Addresses
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test address add dev foo.\$i 2000::\$i/64; done"
echo Attaching to VRF
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link set foo.\$i master florp; done"
On an Intel(R) Xeon(R) CPU E5-2650 v3 @ 2.30GHz machine, the performance
before the patch is (truncated):
Creating vlans
real 108.35
Bringing them up
real 4.96
Assiging IPv6 Addresses
real 19.22
Attaching to VRF
real 458.84
After the patch:
Creating vlans
real 5.59
Bringing them up
real 5.07
Assiging IPv6 Addresses
real 5.64
Attaching to VRF
real 25.37
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lu Wei <luwei32@huawei.com>
Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a predicate that returns if PCIe PTM (Precision Time Measurement)
is enabled.
It will only return true if it's enabled in all the ports in the path
from the device to the root.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make pci_enable_ptm() accessible from the drivers.
Exposing this to the driver enables the driver to use the
'ptm_enabled' field of 'pci_dev' to check if PTM is enabled or not.
This reverts commit ac6c26da29c1 ("PCI: Make pci_enable_ptm() private").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both struct netdev_rx_queue and struct xdp_rxq_info are cacheline
aligned. This causes extra padding before and after the xdp_rxq
member. Move the member upfront, so that it's naturally aligned.
Before:
/* size: 256, cachelines: 4, members: 6 */
/* sum members: 160, holes: 1, sum holes: 40 */
/* padding: 56 */
/* paddings: 1, sum paddings: 36 */
/* forced alignments: 1, forced holes: 1, sum forced holes: 40 */
After:
/* size: 192, cachelines: 3, members: 6 */
/* padding: 32 */
/* paddings: 1, sum paddings: 36 */
/* forced alignments: 1 */
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20210823180135.1153608-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit e358bef7c392 ("net: dsa: Give drivers the chance
to veto certain upper devices"), the hellcreek driver uses some tricks
to comply with the network stack expectations: it enforces port
separation in standalone mode using VLANs. For untagged traffic,
bridging between ports is prevented by using different PVIDs, and for
VLAN-tagged traffic, it never accepts 8021q uppers with the same VID on
two ports, so packets with one VLAN cannot leak from one port to another.
That is almost fine*, and has worked because hellcreek relied on an
implicit behavior of the DSA core that was changed by the previous
patch: the standalone ports declare the 'rx-vlan-filter' feature as 'on
[fixed]'. Since most of the DSA drivers are actually VLAN-unaware in
standalone mode, that feature was actually incorrectly reflecting the
hardware/driver state, so there was a desire to fix it. This leaves the
hellcreek driver in a situation where it has to explicitly request this
behavior from the DSA framework.
We configure the ports as follows:
- Standalone: 'rx-vlan-filter' is on. An 8021q upper on top of a
standalone hellcreek port will go through dsa_slave_vlan_rx_add_vid
and will add a VLAN to the hardware tables, giving the driver the
opportunity to refuse it through .port_prechangeupper.
- Bridged with vlan_filtering=0: 'rx-vlan-filter' is off. An 8021q upper
on top of a bridged hellcreek port will not go through
dsa_slave_vlan_rx_add_vid, because there will not be any attempt to
offload this VLAN. The driver already disables VLAN awareness, so that
upper should receive the traffic it needs.
- Bridged with vlan_filtering=1: 'rx-vlan-filter' is on. An 8021q upper
on top of a bridged hellcreek port will call dsa_slave_vlan_rx_add_vid,
and can again be vetoed through .port_prechangeupper.
*It is not actually completely fine, because if I follow through
correctly, we can have the following situation:
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0 # lan0 now becomes VLAN-unaware
ip link set lan0 nomaster # lan0 fails to become VLAN-aware again, therefore breaking isolation
This patch fixes that corner case by extending the DSA core logic, based
on this requested attribute, to change the VLAN awareness state of the
switch (port) when it leaves the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.15
First set of patches for v5.15. This got delayed as I have been mostly
offline for the last few weeks. The biggest change is removal of
prism54 driver, otherwise just smaller changes.
Major changes:
ath5k, ath9k, ath10k, ath11k:
* switch from 'pci_' to 'dma_' API
brcmfmac
* allow per-board firmware binaries
* add support 43752 SDIO device
prism54
* remove the obsoleted driver, everyone should be using p54 driver instead
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right now, cross-tree bridging setups work somewhat by mistake.
In the case of cross-tree bridging with sja1105, all switch instances
need to agree upon a common VLAN ID for forwarding a packet that belongs
to a certain bridging domain.
With TX forwarding offload, the VLAN ID is the bridge VLAN for
VLAN-aware bridging, and the tag_8021q TX forwarding offload VID
(a VLAN which has non-zero VBID bits) for VLAN-unaware bridging.
The VBID for VLAN-unaware bridging is derived from the dp->bridge_num
value calculated by DSA independently for each switch tree.
If ports from one tree join one bridge, and ports from another tree join
another bridge, DSA will assign them the same bridge_num, even though
the bridges are different. If cross-tree bridging is supported, this
is an issue.
Modify DSA to calculate the bridge_num globally across all switch trees.
This has the implication for a driver that the dp->bridge_num value that
DSA will assign to its ports might not be contiguous, if there are
boards with multiple DSA drivers instantiated. Additionally, all
bridge_num values eat up towards each switch's
ds->num_fwd_offloading_bridges maximum, which is potentially unfortunate,
and can be seen as a limitation introduced by this patch. However, that
is the lesser evil for now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add HW and SDIO ids for use with the SparkLan AP6275S
Add the firmware mapping structures for the BRCM43752 chipset.
The 43752 needs some things setup similar to the 43012 chipset.
The WATERMARK shows better performance when initialized to the 4373 value.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812165218.2508258-2-angus@akkea.ca
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Minor updates:
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
* tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix BSS color notify trace enum confusion
mac80211: Fix insufficient headroom issue for AMSDU
mac80211: add support for BSS color change
nl80211: add support for BSS coloring
mac80211: Use flex-array for radiotap header bitmap
mac80211: radiotap: Use BIT() instead of shifts
mac80211: Remove unnecessary variable and label
mac80211: include <linux/rbtree.h>
mac80211: Fix monitor MTU limit so that A-MSDUs get through
mac80211: remove unnecessary NULL check in ieee80211_register_hw()
mac80211: Reject zero MAC address in sta_info_insert_check()
nl80211: vendor-cmd: add Intel vendor commands for iwlmei usage
====================
Link: https://lore.kernel.org/r/20210820105329.48674-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-08-19
This series introduces the support for two new mlx5 features:
1) Sample offload for tunneled traffic
2) devlink rate objects support
1) From Chris Mi: Sample offload for tunneled traffic
=====================================================
Background and solution
-----------------------
Currently the sample offload actions send the encapsulated packet
to software. This series de-capsulates the packet before performing
the sampling and set the tunnel properties on the skb metadata
fields to make the behavior consistent with OVS sFlow.
If de-capsulating first, we can't use the same match like before in
default table. So instantiate a post action instance to continue
processing the action list. If HW can preserve reg_c, also use the
post action instance.
Post action infrastructure
--------------------------
Some tc actions are modeled in hardware using multiple tables
causing a tc action list split. For example, CT action is modeled
by jumping to a ct table which is controlled by nf flow table.
sFlow jumps in hardware to a sample table, which continues to a
"default table" where it should continue processing the action list.
Multi table actions are modeled in hardware using a unique fte_id.
The fte_id is set before jumping to a table. Split actions continue
to a post-action table where the matched fte_id value continues the
execution the tc action list.
This series also introduces post action infrastructure. Both ct and
sample use it.
Sample for tunnel in TC SW
--------------------------
tc filter add dev vxlan1 protocol ip parent ffff: prio 3 \
flower src_mac 24:25:d0:e1:00:00 dst_mac 02:25:d0:13:01:02 \
enc_src_ip 192.168.1.14 enc_dst_ip 192.168.1.13 \
enc_dst_port 4789 enc_key_id 4 \
action sample rate 1 group 6 \
action tunnel_key unset \
action mirred egress redirect dev enp4s0f0_1
MLX5 sample HW offload
----------------------
For the following typical flow table:
+-------------------------------+
+ original flow table +
+-------------------------------+
+ original match +
+-------------------------------+
+ sample action + other actions +
+-------------------------------+
We translate the tc filter with sample action to the following HW model:
+---------------------+
+ original flow table +
+---------------------+
+ original match +
+---------------------+
| set fte_id (if reg_c preserve cap)
| do decap
v
+------------------------------------------------+
+ Flow Sampler Object +
+------------------------------------------------+
+ sample ratio +
+------------------------------------------------+
+ sample table id | default table id +
+------------------------------------------------+
| |
v v
+-----------------------------+ +-------------------+
+ sample table + + default table +
+-----------------------------+ +-------------------+
+ forward to management vport + |
+-----------------------------+ |
+-------+------+
| |reg_c preserve cap
| |or decap action
v v
+-----------------+ +-------------+
+ per vport table + + post action +
+-----------------+ +-------------+
+ original match +
+-----------------+
+ other actions +
+-----------------+
2) From Dmytro Linkin: devlink rate object support for mlx5_core driver
=======================================================================
HIGH-LEVEL OVERVIEW
Devlink leaf rate objects created per vport (VF/SF, and PF on BlueField)
in switchdev mode on devlink port registration.
Implement devlink ops callbacks to create/destroy rate groups, set TX
rate values of the vport/group, assign vport to the group.
Driver accepts TX rate values as fraction of 1Mbps.
Refactor existing eswitch QoS infrastructure to be accessible by legacy
NDO rate API and new devlink rate API. NDO rate API is not
removed/disabled in switchdev mode to not break existing users. Rate
values configured with NDO rate API are not visible for devlink
infrastructure, therefore APIs should not be used simultaneously.
IMPLEMENTATION DETAILS
Driver provide two level rate hierarchy to manage bandwidth - group
level and vport level. Initially each vport added to internal unlimited
group created by default. Each rate element (vport or group) receive
bandwidth relative to its parent element (for groups the parent is a
physical link itself) in a Round Robin manner, where element get
bandwidth value according to its weight. Example:
Created four rate groups with tx_share limits:
$ devlink port function rate add \
pci/0000:06:00.0/group_1 tx_share 30gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_2 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_3 tx_share 20gbit
$ devlink port function rate add \
pci/0000:06:00.0/group_4 tx_share 10gbit
Weights created in HW for each group are relative to the bigest tx_share
value, which is 30gbit:
<group_1> 1.0
<group_2> 0.67
<group_3> 0.67
<group_4> 0.33
Assuming link speed is 50 Gbit/sec and each group can sustain such
amount of traffic, maximum bandwidth is 50 / (1.0 + 0.67 + 0.67 + 0.33)
= ~18.75 Gbit/sec. Normilized bandwidth values for groups:
<group_1> 18.75 * 1.0 = 18.75 Gbit/sec
<group_2> 18.75 * 0.67 = 12.5 Gbit/sec
<group_3> 18.75 * 0.67 = 12.5 Gbit/sec
<group_4> 18.75 * 0.33 = 6.25 Gbit/sec
If in example above group_1 doesn't produce any traffic, then maximum
bandwidth becomes 50 / (0.67 + 0.67 + 0.33) = ~30.0 Gbit/sec. Normalized
values:
<group_2> 30.0 * 0.67 = 20.0 Gbit/sec
<group_3> 30.0 * 0.67 = 20.0 Gbit/sec
<group_4> 30.0 * 0.33 = 10.0 Gbit/sec
Same normalization applied to each vport in the group.
Normalized values are internal, therefore driver provides QoS
tracepoints for next events:
* vport rate element creation/deletion:
* vport rate element configuration;
* group rate element creation/deletion;
* group rate element configuration.
PATCHES OVERVIEW
1 - Moving and isolation of eswitch QoS logic in separate file;
2 - Implement devlink leaf rate object support for vports;
3 - Implement rate groups creation/deletion;
4 - Implement TX rate management for the groups;
5 - Implement parent set for vports;
6 - Eswitch QoS tracepoints.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend eswitch API with rate limiting groups:
- Define new struct mlx5_esw_rate_group that is used to hold all
internal group data.
- Implement functions that allow creation, destruction and cleanup of
groups.
- Assign all vports to internal unlimited zero group by default.
This commit lays the groundwork for group rate limiting by implementing
devlink_ops->rate_node_{new|del}() callbacks to support creating and
deleting groups through devlink rate node objects. APIs that allows
setting rates and adding/removing members are implemented in following
patches.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Huy Nguyen <huyn@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
drivers/ptp/Kconfig:
55c8fca1dae1 ("ptp_pch: Restore dependency on PCI")
e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from bpf, wireless and mac80211
trees.
Current release - regressions:
- tipc: call tipc_wait_for_connect only when dlen is not 0
- mac80211: fix locking in ieee80211_restart_work()
Current release - new code bugs:
- bpf: add rcu_read_lock in bpf_get_current_[ancestor_]cgroup_id()
- ethernet: ice: fix perout start time rounding
- wwan: iosm: prevent underflow in ipc_chnl_cfg_get()
Previous releases - regressions:
- bpf: clear zext_dst of dead insns
- sch_cake: fix srchost/dsthost hashing mode
- vrf: reset skb conntrack connection on VRF rcv
- net/rds: dma_map_sg is entitled to merge entries
Previous releases - always broken:
- ethernet: bnxt: fix Tx path locking and races, add Rx path
barriers"
* tag 'net-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
net: dpaa2-switch: disable the control interface on error path
Revert "flow_offload: action should not be NULL when it is referenced"
iavf: Fix ping is lost after untrusted VF had tried to change MAC
i40e: Fix ATR queue selection
r8152: fix the maximum number of PLA bp for RTL8153C
r8152: fix writing USB_BP2_EN
mptcp: full fully established support after ADD_ADDR
mptcp: fix memory leak on address flush
net/rds: dma_map_sg is entitled to merge entries
net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU port
net: asix: fix uninit value bugs
ovs: clear skb->tstamp in forwarding path
net: mdio-mux: Handle -EPROBE_DEFER correctly
net: mdio-mux: Don't ignore memory allocation errors
net: mdio-mux: Delete unnecessary devm_kfree
net: dsa: sja1105: fix use-after-free after calling of_find_compatible_node, or worse
sch_cake: fix srchost/dsthost hashing mode
ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error path
net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32
mac80211: fix locking in ieee80211_restart_work()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-5.15-20210819
The first patch is by me, for the mailmap file and maps the email
address of two former ESD employees to a newly created role account.
The next 3 patches are by Oleksij Rempel and add support for GPIO
based switchable CAN bus termination.
The next 3 patches are by Vincent Mailhol. The first one changes the
CAN netlink interface to not bail out if the user switched off
unsupported features. The next one adds Vincent as the maintainer of
the etas_es58x driver and the last one cleans up the documentation of
struct es58x_fd_tx_conf_msg.
The next patch is by me, for the mcp251xfd driver and marks some
instances of struct mcp251xfd_priv as const. Lad Prabhakar contributes
2 patches for the rcar_canfd driver, that add support for RZ/G2L
family.
The next 5 patches target the m_can/tcan45x5 driver. 2 are by me an
fix trivial checkpatch warnings. The remaining 3 patches are by Matt
Kline and improve the performance on the SPI based tcan4x5x chip by
batching FIFO reads and writes.
The last 7 patches are for the c_can driver. Dario Binacchi's patch
converts the DT bindings to yaml, 2 patches by me fix a typo and
rename a macro to properly represent the usage. The last 4 patches are
again by Dario Binacchi and provide a performance improvement for the
TX path by operating the TX mailboxes as a true FIFO.
* tag 'linux-can-next-for-5.15-20210819' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (22 commits)
can: c_can: cache frames to operate as a true FIFO
can: c_can: support tx ring algorithm
can: c_can: exit c_can_do_tx() early if no frames have been sent
can: c_can: remove struct c_can_priv::priv field
can: c_can: rename IF_RX -> IF_NAPI
can: c_can: c_can_do_tx(): fix typo in comment
dt-bindings: net: can: c_can: convert to json-schema
can: m_can: Batch FIFO writes during CAN transmit
can: m_can: Batch FIFO reads during CAN receive
can: m_can: Disable IRQs on FIFO bus errors
can: m_can: fix block comment style
can: tcan4x5x: cdev_to_priv(): remove stray empty line
can: rcar_canfd: Add support for RZ/G2L family
dt-bindings: net: can: renesas,rcar-canfd: Document RZ/G2L SoC
can: mcp251xfd: mark some instances of struct mcp251xfd_priv as const
can: etas_es58x: clean-up documentation of struct es58x_fd_tx_conf_msg
MAINTAINERS: add Vincent MAILHOL as maintainer for the ETAS ES58X CAN/USB driver
can: netlink: allow user to turn off unsupported features
can: dev: provide optional GPIO based termination support
dt-bindings: can: fsl,flexcan: enable termination-* bindings
...
====================
Link: https://lore.kernel.org/r/20210819133913.657715-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 9ea3e52c5bc8bb4a084938dc1e3160643438927a.
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com>
Fixes: 9ea3e52c5bc8 ("flow_offload: action should not be NULL when it is referenced")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.
This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.
Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mii_ethtool_gset() does not return any errors. Since there are no users
of this function that rely on its return value, it can be
made void.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88ca ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/
Fixes: 3a34b13a88ca ("pipe: make pipe writes always wake up readers")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Sandeep Patil <sspatil@android.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add gfp_t mask as an input parameter to mem_cgroup_charge_skmem(),
to give more control to the networking stack and enable it to change
memcg charging behavior. In the future, the networking stack may decide
to avoid oom-kills when fallbacks are more appropriate.
One behavior change in mem_cgroup_charge_skmem() by this patch is to
avoid force charging by default and let the caller decide when and if
force charging is needed through the presence or absence of
__GFP_NOFAIL.
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).
This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.
Some sane defaults must also take place when not running on sja1105
hardware. These are:
- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
depending on VLAN awareness and switch revision (when an encapsulated
VLAN must be sent). Default to 0x8100.
- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
metadata timestamp frames. When running on non-sja1105 hardware, don't
do that and accept all frames unmodified.
- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
which writes a management route over SPI. When not running on sja1105
hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added and managed a new per endpoint flag, named
MPTCP_PM_ADDR_FLAG_FULLMESH.
In mptcp_pm_create_subflow_or_signal_addr(), if such flag is set, instead
of:
remote_address((struct sock_common *)sk, &remote);
fill a temporary allocated array of all known remote address. After
releaseing the pm lock loop on such array and create a subflow for each
remote address from the given local.
Note that the we could still use an array even for non 'fullmesh'
endpoint: with a single entry corresponding to the primary MPC subflow
remote address.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds support for BSS color collisions to the wireless subsystem.
Add the required functionality to nl80211 that will notify about color
collisions, triggering the color change and notifying when it is completed.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/500b3582aec8fe2c42ef46f3117b148cb7cbceb5.1625247619.git.lorenzo@kernel.org
[remove unnecessary NULL initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST means the input
external clock signal for SerDes is too weak or lost.
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS means the received signal for
SerDes is too weak because analog loss of signal.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes in virtio, vhost, and vdpa drivers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix queue type selection logic
vdpa/mlx5: Avoid destroying MR on empty iotlb
tools/virtio: fix build
virtio_ring: pull in spinlock header
vringh: pull in spinlock header
virtio-blk: Add validation for block size in config space
vringh: Use wiov->used to check for read/write desc order
virtio_vdpa: reject invalid vq indices
vdpa: Add documentation for vdpa_alloc_device() macro
vDPA/ifcvf: Fix return value check for vdpa_alloc_device()
vp_vdpa: Fix return value check for vdpa_alloc_device()
vdpa_sim: Fix return value check for vdpa_alloc_device()
vhost: Fix the calculation in vhost_overflow()
vhost-vdpa: Fix integer overflow in vhost_vdpa_process_iotlb_update()
virtio_pci: Support surprise removal of virtio pci device
virtio: Protect vqs list access
virtio: Keep vring_del_virtqueue() mirror of VQ create
virtio: Improve vq->broken access to avoid any compiler optimization
|
|
This stores the advertising handle/instance into hci_conn so it is
accessible when re-enabling the advertising once disconnected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for PCI/MSI and x86 interrupt startup:
- Mask all MSI-X entries when enabling MSI-X otherwise stale unmasked
entries stay around e.g. when a crashkernel is booted.
- Enforce masking of a MSI-X table entry when updating it, which
mandatory according to speification
- Ensure that writes to MSI[-X} tables are flushed.
- Prevent invalid bits being set in the MSI mask register
- Properly serialize modifications to the mask cache and the mask
register for multi-MSI.
- Cure the violation of the affinity setting rules on X86 during
interrupt startup which can cause lost and stale interrupts. Move
the initial affinity setting ahead of actualy enabling the
interrupt.
- Ensure that MSI interrupts are completely torn down before freeing
them in the error handling case.
- Prevent an array out of bounds access in the irq timings code"
* tag 'irq-urgent-2021-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
driver core: Add missing kernel doc for device::msi_lock
genirq/msi: Ensure deactivation on teardown
genirq/timings: Prevent potential array overflow in __irq_timings_store()
x86/msi: Force affinity setup before startup
x86/ioapic: Force affinity setup before startup
genirq: Provide IRQCHIP_AFFINITY_PRE_STARTUP
PCI/MSI: Protect msi_desc::masked for multi-MSI
PCI/MSI: Use msi_mask_irq() in pci_msi_shutdown()
PCI/MSI: Correct misleading comments
PCI/MSI: Do not set invalid bits in MSI mask
PCI/MSI: Enforce MSI[X] entry updates to be visible
PCI/MSI: Enforce that MSI-X table entry is masked for update
PCI/MSI: Mask all unused MSI-X entries
PCI/MSI: Enable and mask MSI-X early
|
|
commit <47595e32869f> ("<MAINTAINERS: Mark some staging directories>")
indicated the ipx network layer as obsolete in Jan 2018,
updated in the MAINTAINERS file
now, after being exposed for 3 years to refactoring, so to
delete uapi/linux/ipx.h and net/ipx.h header files for good.
additionally, there is no module that depends on ipx.h except
a broken staging driver(r8188eu)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new mcast querier state dump infrastructure and export vlans'
mcast context querier state embedded in attribute
BRIDGE_VLANDB_GOPTS_MCAST_QUERIER_STATE.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for dumping global IPv6 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IPV6_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IPV6_PORT] - bridge port ifindex where the querier
was seen (set only if external querier)
`[BRIDGE_QUERIER_IPV6_OTHER_TIMER] - other querier timeout
IPv4 and IPv6 attributes are embedded at the same level of
IFLA_BR_MCAST_QUERIER_STATE. If we didn't dump anything we cancel the nest
and return.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for dumping global IPv4 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can use xarray instead of linearly organized linked lists for the
devlink instances. This will let us revise the locking scheme in favour
of internal xarray locking that protects database.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct devlink itself is protected by internal lock and doesn't
need global lock during operation. That global lock is used to protect
addition/removal new devlink instances from the global list in use by
all devlink consumers in the system.
The future conversion of linked list to be xarray will allow us to
actually delete that lock, but first we need to count all struct devlink
users.
The reference counting provides us a way to ensure that no new user
space commands success to grab devlink instance which is going to be
destroyed makes it is safe to access it without lock.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the obsolete and ambiguos macro in_irq() with new
macro in_hardirq().
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Link: https://lore.kernel.org/r/20210813145749.86512-1-changbin.du@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
