| Age | Commit message (Collapse) | Author |
|---|
|
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch prepares for changing the max14577 charger driver to allow
configuring battery-dependent settings from DTS.
The patch moves from regulator driver to MFD core driver and exports:
- function for calculating register value for charger's current;
- table of limits for chargers (MAX14577, MAX77836).
Previously they were used only by the max14577 regulator driver. In next
patch the charger driver will use them as well. Exporting them will
reduce unnecessary code duplication.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Remove not needed max14577-private.h header inclusion in the main driver
header. Remove obvious comment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds max14577 core/irq driver to support MUIC(Micro USB IC)
device and charger device and support irq domain method to control
internal interrupt of max14577 device. Also, this patch supports DT
binding with max14577_i2c_parse_dt().
The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery
Charger. It contains accessory and USB charger detection logic. It supports
USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector.
The battery charger is compliant with the USB Battery Charging Specification
Revision 1.1. It has also SFOUT LDO output for powering USB devices.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
