| Age | Commit message (Collapse) | Author |
|---|
|
The netvsc VF skb handler should make sure that skb is not
shared. Similar logic already exists in bonding and team device
drivers.
This is not an issue in practice because the VF devicex
does not send up shared skb's. But the netvsc driver
should do the right thing if it did.
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phy state machine calls _config_init just after
reset.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure only the portals for the online CPUs are used.
Without this change, there are issues when someone boots with
maxcpus=n, with n < actual number of cores available as frames
either received or corresponding to the transmit confirmation
path would be offered for dequeue to the offline CPU portals,
getting lost.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix below issues in err code path of probe:
1. we don't need to unregister_netdev() because the netdev isn't
registered.
2. when register_netdev() fails, we also need to destroy bm pool for
HWBM case.
Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the subdriver defers probe, do not show an error message. It's
perfectly fine for this error to occur since the driver will get another
chance to probe after some time and will usually succeed after all of
the resources that it requires have been registered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thats a known quirk in windows tcp stack it can produce 0xffff checksum.
Thats incorrect but it is.
Atlantic HW with LRO enabled handles that incorrectly and changes csum to
0xfffe - but indicates that csum is invalid. This causes driver to pass
packet to linux networking stack with CSUM_NONE, stack eventually drops
the packet.
There is a quirk in atlantic HW to enable correct processing of
0xffff incorrect csum. Enable it.
The visible bug is that windows link partner with software generated csums
caused TCP connection to be unstable since all packets that csum value
are dropped.
Reported-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver stops producing skbs on ring if a packet with FCS error
was coalesced into LRO session. Ring gets hang forever.
Thats a logical error in driver processing descriptors:
When rx_stat indicates MAC Error, next pointer and eop flags
are not filled. This confuses driver so it waits for descriptor 0
to be filled by HW.
Solution is fill next pointer and eop flag even for packets with FCS error.
Fixes: bab6de8fd180b ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Atlantic hardware does not aggregate nor breaks LRO sessions
with bad csum packets. This means driver should take care of that.
If in LRO session there is a non-first descriptor with invalid
checksum (L2/L3/L4), the driver must account this information
in csum application logic.
Fixes: 018423e90bee8 ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case no other traffic happening on the ring, full tx cleanup
may not be completed. That may cause socket buffer to overflow
and tx traffic to stuck until next activity on the ring happens.
This is due to logic error in budget variable decrementor.
Variable is compared with zero, and then post decremented,
causing it to become MAX_INT. Solution is remove decrementor
from the `for` statement and rewrite it in a clear way.
Fixes: b647d3980948e ("net: aquantia: Add tx clean budget and valid budget handling logic")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building with Clang reports the redundant use of MODULE_DEVICE_TABLE():
drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table'
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:90:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:85:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
This drops the one further from the table definition to match the common
use of MODULE_DEVICE_TABLE().
Fixes: 07563c711fbc ("EISA bus MODALIAS attributes support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function dpaa2_eth_cls_key_size() expects a 64bit argument,
but DPAA2_ETH_DIST_ALL is defined as UINT_MAX. Fix this.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PTR_ERR_OR_ZERO instead of PTR_ERR in cases where
zero is a valid input. Reported by smatch.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch reports a potential spectre vulnerability in the dpaa2-eth
driver, where the value of rxnfc->fs.location (which is provided
from user-space) is used as index in an array.
Add a call to array_index_nospec() to sanitize the access.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once in a while, with just the right timing, 802.3ad slaves will fail to
properly initialize, winding up in a weird state, with a partner system
mac address of 00:00:00:00:00:00. This started happening after a fix to
properly track link_failure_count tracking, where an 802.3ad slave that
reported itself as link up in the miimon code, but wasn't able to get a
valid speed/duplex, started getting set to BOND_LINK_FAIL instead of
BOND_LINK_DOWN. That was the proper thing to do for the general "my link
went down" case, but has created a link initialization race that can put
the interface in this odd state.
The simple fix is to instead set the slave link to BOND_LINK_DOWN again,
if the link has never been up (last_link_up == 0), so the link state
doesn't bounce from BOND_LINK_DOWN to BOND_LINK_FAIL -- it hasn't failed
in this case, it simply hasn't been up yet, and this prevents the
unnecessary state change from DOWN to FAIL and getting stuck in an init
failure w/o a partner mac.
Fixes: ea53abfab960 ("bonding/802.3ad: fix link_failure_count tracking")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Tested-by: Heesoon Kim <Heesoon.Kim@stratus.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. the frequency of csr clock is 66.5MHz, so the csr_clk value should
be 0 other than 5.
2. the csr_clk can be got from device tree, so remove initialization here.
Fixes: 9992f37e346b ("stmmac: dwmac-mediatek: add support for mt2712")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specific clk_csr value can be zero, and
stmmac_clk is necessary for MDC clock which can be set dynamically.
So, change the condition from plat->clk_csr to plat->stmmac_clk to
fix clk_csr can't be zero issue.
Fixes: cd7201f477b9 ("stmmac: MDC clock dynamically based on the csr clock input")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.
Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 2391b0030e241386d710df10e53e2cfc3c5d4fc1 which has
introduced regression. Now SGE's BAR2 Doorbell/GTS Page Size is
interpreted correctly in the firmware itself by using actual host
page size. Hence previous commit needs to be reverted.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN flows never get offloaded unless ivlan_vld is set in filter spec.
It's not compulsory for vlan_ethtype to be set.
So, always enable ivlan_vld bit for offloading VLAN flows regardless of
vlan_ethtype is set or not.
Fixes: ad9af3e09c (cxgb4: add tc flower match support for vlan)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow_rule is only used when configuring the classification tables,
and should be free'd once we're done using it. The current code only
frees it in the error path.
Fixes: 90b509b39ac9 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't read DSN on VFs that do not have the PCI capability.
Fixes: 03213a996531 ("bnxt: move bp->switch_id initialization to PF probe")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skip RDMA context memory allocations, reduce to 1 ring, and disable
TPA when running in the kdump kernel. Without this patch, the driver
fails to initialize with memory allocation errors when running in a
typical kdump kernel.
Fixes: cf6daed098d1 ("bnxt_en: Increase context memory allocations on 57500 chips for RDMA.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When making configuration changes, the driver calls bnxt_close_nic()
and then bnxt_open_nic() for the changes to take effect. A parameter
irq_re_init is passed to the call sequence to indicate if IRQ
should be re-initialized. This irq_re_init parameter needs to
be included in the bnxt_reserve_rings() call. bnxt_reserve_rings()
can only call pci_disable_msix() if the irq_re_init parameter is
true, otherwise it may hit BUG() because some IRQs may not have been
freed yet.
Fixes: 41e8d7983752 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For every RX packet, the driver replenishes all buffers used for that
packet and puts them back into the RX ring and RX aggregation ring.
In one code path where the RX packet has one RX buffer and one or more
aggregation buffers, we missed recycling the aggregation buffer(s) if
we are unable to allocate a new SKB buffer. This leads to the
aggregation ring slowly running out of buffers over time. Fix it
by properly recycling the aggregation buffers.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Rakesh Hemnani <rhemnani@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The user can change the device_name with the IMSETDEVNAME ioctl, but we
need to ensure that the user's name is NUL terminated. Otherwise it
could result in a buffer overflow when we copy the name back to the user
with IMGETDEVINFO ioctl.
I also changed two strcpy() calls which handle the name to strscpy().
Hopefully, there aren't any other ways to create a too long name, but
it's nice to do this as a kernel hardening measure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SAMA5D2 SoC has a suspend mode where SoC's power is cut off. Due to this
the registers content is lost after a suspend/resume cycle. The current
suspend/resume implementation covers some of these registers. However
there are few which were not treated (e.g. SCRT2 and USRIO). Apart
from this, netdev features are not restored. Treat these issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used a script to indent this code back in 2012, but I guess it got
confused by the ifdefs and added some extra tabs. This patch removes
them.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doing kmalloc in atomic context is always an issue,
more so for a list that can grow significantly.
Turns out that the driver only uses the duplicated
list of multicast mac addresses to keep track of
what addresses to delete from h/w before committing
the new list from kernel to h/w back again via set_rx_mode,
every time this list gets updated by the kernel.
Given that the h/w knows how to add and delete mac addresses
based on the mac address value alone, __dev_mc_sync should be
the much better choice of kernel API for these operations
avoiding the considerable overhead of maintaining a duplicated
list in the driver.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: vdso: Explicitly add build-id option
arm64/mm: Inhibit huge-vmap with ptdump
arm64: Print physical address of page table base in show_pte()
arm64: don't trash config with compat symbol if COMPAT is disabled
arm64: assembler: Update comment above cond_yield_neon() macro
drivers/perf: arm_spe: Don't error on high-order pages for aux buf
arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
|
|
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a particularly glaring oversight in a DM core commit from 5.1 that
doesn't properly trim special IOs (e.g. discards) relative to
corresponding target's max_io_len_target_boundary()"
* tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: make sure to obey max_io_len_target_boundary
|
|
Commit 61697a6abd24 ("dm: eliminate 'split_discard_bios' flag from DM
target interface") incorrectly removed code from
__send_changing_extent_only() that is required to impose a per-target IO
boundary on IO that exceeds max_io_len_target_boundary(). Otherwise
"special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond
where allowed.
Fix this by restoring the max_io_len_target_boundary() limit in
__send_changing_extent_only()
Fixes: 61697a6abd24 ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Michael Lass <bevan@bi-co.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When disconnecting cdc_ncm the kernel sporadically crashes shortly
after the disconnect:
[ 57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 58.006653] PC is at 0x0
[ 58.009202] LR is at call_timer_fn+0xec/0x1b4
[ 58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145
[ 58.020976] sp : ffffff8008003da0
[ 58.024295] x29: ffffff8008003da0 x28: 0000000000000001
[ 58.029618] x27: 000000000000000a x26: 0000000000000100
[ 58.034941] x25: 0000000000000000 x24: ffffff8008003e68
[ 58.040263] x23: 0000000000000000 x22: 0000000000000000
[ 58.045587] x21: 0000000000000000 x20: ffffffc68fac1808
[ 58.050910] x19: 0000000000000100 x18: 0000000000000000
[ 58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10
[ 58.061556] x15: 0000000000000001 x14: 000000000000006e
[ 58.066878] x13: 0000000000000000 x12: 00000000000000ba
[ 58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020
[ 58.077524] x9 : 8000100008001000 x8 : 0000000000000001
[ 58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70
[ 58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b
[ 58.093492] x3 : 0000000000000000 x2 : 0000000000000000
[ 58.098814] x1 : 0000000000000000 x0 : 0000000000000000
...
[ 58.205800] [< (null)>] (null)
[ 58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c
[ 58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128
[ 58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348
[ 58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc
[ 58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac
[ 58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac
...
The crash happens roughly 125..130ms after the disconnect. This
correlates with the 'delay' timer that is started on certain USB tx/rx
errors in the URB completion handler.
The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
flight. This only makes sense if no new URBs are submitted
concurrently, though. But the usbnet_start_xmit() can run at the same
time on another CPU which almost unconditionally submits an URB. The
error callback of the new URB will then schedule the timer after it was
already stopped.
The fix adds a check if the tx queue is stopped after the tx list lock
has been taken. This should reliably prevent the submission of new URBs
while usbnet_terminate_urbs() does its job. The same thing is done on
the rx side even though it might be safe due to other flags that are
checked there.
Signed-off-by: Jan Klötzke <Jan.Kloetzke@preh.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not update the link interface mode while the link is down to avoid
spurious link interface changes.
Always call mac_config if we have a PHY to propagate the pause mode
settings to the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a racing condition in ipheth.c that can lead to slow performance.
Bug: In ipheth_tx(), netif_wake_queue() may be called on the callback
ipheth_sndbulk_callback(), _before_ netif_stop_queue() is called.
When this happens, the queue is stopped longer than it needs to be,
thus reducing network performance.
Fix: Move netif_stop_queue() in front of usb_submit_urb(). Now the order
is always correct. In case, usb_submit_urb() fails, the queue is woken up
again as callback will not fire.
Testing: This racing condition is usually not noticeable, as it has to
occur very frequently to slowdown the network. The callback from the USB
is usually triggered slow enough, so the situation does not appear.
However, on a Ubuntu Linux on VMWare Workstation, running on Windows 10,
the we loose the race quite often and the following speedup can be noticed:
Without this patch: Download: 4.10 Mbit/s, Upload: 4.01 Mbit/s
With this patch: Download: 36.23 Mbit/s, Upload: 17.61 Mbit/s
Signed-off-by: Oliver Zweigle <Oliver.Zweigle@faro.com>
Signed-off-by: Bernd Eckstein <3ernd.Eckstein@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Two long-standing bugs in the powerpc assembly of vmx
- Stack overrun caused by HASH_MAX_DESCSIZE being too small
- Regression in caam
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: vmx - ghash: do nosimd fallback manually
crypto: vmx - CTR: always increment IV as quadword
crypto: hash - fix incorrect HASH_MAX_DESCSIZE
crypto: caam - fix typo in i.MX6 devices list for errata
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.917228456@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this software may be redistributed and or modified under the terms
of the gnu general public license as published by the free software
foundation either version 2 of the license or any later version this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.800979546@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.707528683@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.615184352@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program see the file copying if not write to the free
software foundation inc 51 franklin steet fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 41 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.524645346@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
