| Age | Commit message (Collapse) | Author |
|---|
|
Be a little wasteful if the (likely CMA) message window buffer is not
suitably aligned after our first attempt; allocate a buffer twice as big
as we need and manually align our MW buffer within it.
This was needed on Intel Broadwell DE platforms with intel_iommu=off
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1373888 ("Missing break in switch")
Addresses-Coverity-ID: 1373889 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
IDT NTB driver sets the upper limit of actual translation address
being written to the corresponding memory window setup. It is achieved
by BARLIMITx register initialization. Needless to say, that the register
works within PCIe bus address space.
In general CPU and PCIe address spaces are different. It means,
that addresses used for Memory TLPs routine can be different from
CPU addresses. While in most of cases they are the same, there are
exceptions when the proper mapping must be performed to have the
portable driver code. There used to be a virt_to_bus()/bus_to_virt()
interface for this purpose. But it's deprecated now. It was also a
mistake to use pci_resource_start() since the return address of the
method is at the CPU address space. In order to achieve the desired
purpose we need to use pci_bus_address() helper. This method shall
return a PCIe bus base address of the corresponding BAR resource.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome-platform updates from Benson Leung:
- Move mfd/cros_ec_lpc* includes to drivers/platform from mfd
- Adding a new interrupt path for cros_ec_lpc
* tag 'tag-chrome-platform-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - Remove unneeded const
platform/chrome: Add a new interrupt path for cros_ec_lpc
mfd: cros_ec: Fix and improve kerneldoc comments.
platform/chrome: Move mfd/cros_ec_lpc* includes to drivers/platform.
|
|
The IRQ will be mapped in i2c_device_probe only if client->irq is zero and
i2c_device_remove does not clear this. When rebinding an I2C device,
whos IRQ provider has also been rebound this means that an IRQ mapping
will never be created, causing the I2C device to fail to acquire its
IRQ. Fix this issue by clearing client->irq in i2c_device_remove,
forcing i2c_device_probe to lookup the mapping again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
irq_create_mapping calls irq_find_mapping internally and will use the
found mapping if one exists, so there is no need to manually call this
from i2c_smbus_host_notify_to_irq.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull ceph updates from Ilya Dryomov:
"The highlights are:
- a series that fixes some old memory allocation issues in libceph
(myself). We no longer allocate memory in places where allocation
failures cannot be handled and BUG when the allocation fails.
- support for copy_file_range() syscall (Luis Henriques). If size and
alignment conditions are met, it leverages RADOS copy-from
operation. Otherwise, a local copy is performed.
- a patch that reduces memory requirement of ceph_sync_read() from
the size of the entire read to the size of one object (Zheng Yan).
- fallocate() syscall is now restricted to FALLOC_FL_PUNCH_HOLE (Luis
Henriques)"
* tag 'ceph-for-4.20-rc1' of git://github.com/ceph/ceph-client: (25 commits)
ceph: new mount option to disable usage of copy-from op
ceph: support copy_file_range file operation
libceph: support the RADOS copy-from operation
ceph: add non-blocking parameter to ceph_try_get_caps()
libceph: check reply num_data_items in setup_request_data()
libceph: preallocate message data items
libceph, rbd, ceph: move ceph_osdc_alloc_messages() calls
libceph: introduce alloc_watch_request()
libceph: assign cookies in linger_submit()
libceph: enable fallback to ceph_msg_new() in ceph_msgpool_get()
ceph: num_ops is off by one in ceph_aio_retry_work()
libceph: no need to call osd_req_opcode_valid() in osd_req_encode_op()
ceph: set timeout conditionally in __cap_delay_requeue
libceph: don't consume a ref on pagelist in ceph_msg_data_add_pagelist()
libceph: introduce ceph_pagelist_alloc()
libceph: osd_req_op_cls_init() doesn't need to take opcode
libceph: bump CEPH_MSG_MAX_DATA_LEN
ceph: only allow punch hole mode in fallocate
ceph: refactor ceph_sync_read()
ceph: check if LOOKUPNAME request was aborted when filling trace
...
|
|
Both devm_kcalloc() and devm_kzalloc() return NULL on error. They
never return error pointers.
The use of IS_ERR_OR_NULL is currently applied to the wrong
context.
Fix this by replacing IS_ERR_OR_NULL with regular NULL checks.
Fixes: bf2a952d31d2 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
ndev_vec_mask() should be returning u64 mask value instead of int.
Otherwise the mask value returned can be incorrect for larger
vectors.
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Lucas Van <lucas.van@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The tx_time should be in usecs (according to the comment above the
variable), but the setting of the timer during the rearming is done in
msecs. Change it to match the expected units.
Fixes: e74bfeedad08 ("NTB: Add flow control to the ntb_netdev")
Suggested-by: Gerd W. Haeussler <gerd.haeussler@cesys-it.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Dave Jiang <dave.jiang@intel.com>
|
|
An MC-aware mode was introduced in commit 7b8195306694 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes: b9b7cee40579 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes: 6988eb2a9b77 ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes: 6d4fab39533f ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec3999b3d ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.
Fixes: b50ae26c57cb ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.
Fixes: 3ff504908f95 ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes: 3efb960f056d ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.
Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.
Fixes: cd8c5c269b1d ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.
Before 4.18 (more exactly commit 88078d98d1bb "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.
Then before commit d55bef5059dd ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.
Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.
Note that this patch also rewrites mlx5e_get_fcs() to :
- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
as Dmitris pointed out.
Fixes: 902a545904c7 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Tested-By: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.
Fixing this by sanitizing idx before using it to index d->vqs.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"No major changes to the subsystem itself, mainly fb drivers fixes &
cleanups (atyfb & udlfb updates stand out from the rest) + removal of
no longer needed old clps711xfb driver.
Details:
- update atyfb driver - improvements for ATI Mach64 chips: detect the
dot clock divider correctly on Sparc, fix display corruptions (due
to endianness issues and improper reading of accelerator
registers), optimize scrolling performance and also fix debugging
printks (Mikulas Patocka)
- rewrite USB unplug handling in udlfb driver using framebuffer
subsystem reference counting (Mikulas Patocka)
- fix support for native-mode display-timings in atmel_lcdfb driver
(Sam Ravnborg)
- fix information leak & add missing access_ok() checks in sbuslib
(Dan Carpenter)
- allow using GPIO expanders that can sleep in ssd1307fb driver
(Michal Vokáč)
- convert omapfb driver to use GPIO descriptors instead of GPIO
numbers for Amstrad Delta board (Janusz Krzysztofik)
- fix broken Kconfig menu dependencies (Randy Dunlap)
- convert fbdev subsystem to use %pOFn instead of device_node.name
(Rob Herring)
- remove the dead old CLPS711x LCD support driver (the new CLPS711x
LCD support driver is still available)
- misc fixes (Jia-Ju Bai, Gustavo A. R. Silva)
- misc cleanups (Mehdi Bounya, Nathan Chancellor, YueHaibing)"
* tag 'fbdev-v4.20' of https://github.com/bzolnier/linux: (22 commits)
video: fbdev: remove redundant 'default n' from Kconfig-s
video: fbdev: remove dead old CLPS711x LCD support driver
Revert "video: ssd1307fb: Do not hard code active-low reset sequence"
video: fbdev: arcfb: mark expected switch fall-through
pxa168fb: remove set but not used variables 'mi'
video: ssd1307fb: Do not hard code active-low reset sequence
video: ssd1307fb: Use gpiod_set_value_cansleep() for reset
fbdev: fix broken menu dependencies
video: fbdev: sis: Remove unnecessary parentheses and commented code
video: fbdev: omapfb: lcd_ams_delta: use GPIO lookup table
fbdev: sbuslib: integer overflow in sbusfb_ioctl_helper()
fbdev: sbuslib: use checked version of put_user()
fbdev: Convert to using %pOFn instead of device_node.name
atmel_lcdfb: support native-mode display-timings
Video: vgastate: fixed a spacing coding style
atyfb: fix debugging printks
mach64: optimize wait_for_fifo
mach64: fix image corruption due to reading accelerator registers
mach64: fix display corruption on big endian machines
mach64: detect the dot clock divider correctly on sparc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Fix a use-after-free issue when unregistering a thermal cooling
device (Dmitry Osipenko)
- use power_efficient_wq for thermal worker to save more power (Jeson
Gao)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: core: using power_efficient_wq for thermal worker
thermal: core: Fix use-after-free in thermal_cooling_device_destroy_sysfs
|
|
The driver depends on the ADXL component glue and selects it. However,
ADXL itself implicitly depends on ACPI and in nonsensical randconfig
builds like this:
# CONFIG_ACPI is not set
CONFIG_ACPI_ADXL=y
where ACPI is not enabled, the build fails with:
drivers/edac/skx_edac.o: In function `skx_mce_check_error':
skx_edac.c:(.text+0xab): undefined reference to `adxl_decode'
drivers/edac/skx_edac.o: In function `skx_init':
skx_edac.c:(.init.text+0x8bf): undefined reference to `adxl_get_component_names'
make: *** [vmlinux] Error 1
Add stubs for that case so that the build succeeds. CONFIG_ACPI=n
doesn't make any sense for real configurations but this fix will at
least silence randconfig builds.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
|
|
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Pull VFIO updates from Alex Williamson:
- EDID interfaces for vfio devices supporting display extensions (Gerd
Hoffmann)
- Generically select Type-1 IOMMU model support on ARM/ARM64 (Geert
Uytterhoeven)
- Quirk for VFs reporting INTx pin (Alex Williamson)
- Fix error path memory leak in MSI support (Li Qiang)
* tag 'vfio-v4.20-rc1.v2' of git://github.com/awilliam/linux-vfio:
vfio: add edid support to mbochs sample driver
vfio: add edid api for display (vgpu) devices.
drivers/vfio: Allow type-1 IOMMU instantiation with all ARM/ARM64 IOMMUs
vfio/pci: Mask buggy SR-IOV VF INTx support
vfio/pci: Fix potential memory leak in vfio_msi_cap_len
|
|
Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
|
|
Based on the original work from Arnd Bergmann.
When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'
Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:
A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes: eda0333ac293 ("ixgbe: add VF IPsec management")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There seem to be some problems as result of 30467e0b3be ("mm, hotplug:
fix concurrent memory hot-add deadlock"), which tried to fix a possible
lock inversion reported and discussed in [1] due to the two locks
a) device_lock()
b) mem_hotplug_lock
While add_memory() first takes b), followed by a) during
bus_probe_device(), onlining of memory from user space first took a),
followed by b), exposing a possible deadlock.
In [1], and it was decided to not make use of device_hotplug_lock, but
rather to enforce a locking order.
The problems I spotted related to this:
1. Memory block device attributes: While .state first calls
mem_hotplug_begin() and the calls device_online() - which takes
device_lock() - .online does no longer call mem_hotplug_begin(), so
effectively calls online_pages() without mem_hotplug_lock.
2. device_online() should be called under device_hotplug_lock, however
onlining memory during add_memory() does not take care of that.
In addition, I think there is also something wrong about the locking in
3. arch/powerpc/platforms/powernv/memtrace.c calls offline_pages()
without locks. This was introduced after 30467e0b3be. And skimming over
the code, I assume it could need some more care in regards to locking
(e.g. device_online() called without device_hotplug_lock. This will
be addressed in the following patches.
Now that we hold the device_hotplug_lock when
- adding memory (e.g. via add_memory()/add_memory_resource())
- removing memory (e.g. via remove_memory())
- device_online()/device_offline()
We can move mem_hotplug_lock usage back into
online_pages()/offline_pages().
Why is mem_hotplug_lock still needed? Essentially to make
get_online_mems()/put_online_mems() be very fast (relying on
device_hotplug_lock would be very slow), and to serialize against
addition of memory that does not create memory block devices (hmm).
[1] http://driverdev.linuxdriverproject.org/pipermail/ driverdev-devel/
2015-February/065324.html
This patch is partly based on a patch by Vitaly Kuznetsov.
Link: http://lkml.kernel.org/r/20180925091457.28651-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
add_memory() currently does not take the device_hotplug_lock, however
is aleady called under the lock from
arch/powerpc/platforms/pseries/hotplug-memory.c
drivers/acpi/acpi_memhotplug.c
to synchronize against CPU hot-remove and similar.
In general, we should hold the device_hotplug_lock when adding memory to
synchronize against online/offline request (e.g. from user space) - which
already resulted in lock inversions due to device_lock() and
mem_hotplug_lock - see 30467e0b3be ("mm, hotplug: fix concurrent memory
hot-add deadlock"). add_memory()/add_memory_resource() will create memory
block devices, so this really feels like the right thing to do.
Holding the device_hotplug_lock makes sure that a memory block device
can really only be accessed (e.g. via .online/.state) from user space,
once the memory has been fully added to the system.
The lock is not held yet in
drivers/xen/balloon.c
arch/powerpc/platforms/powernv/memtrace.c
drivers/s390/char/sclp_cmd.c
drivers/hv/hv_balloon.c
So, let's either use the locked variants or take the lock.
Don't export add_memory_resource(), as it once was exported to be used by
XEN, which is never built as a module. If somebody requires it, we also
have to export a locked variant (as device_hotplug_lock is never
exported).
Link: http://lkml.kernel.org/r/20180925091457.28651-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: online/offline_pages called w.o. mem_hotplug_lock", v3.
Reading through the code and studying how mem_hotplug_lock is to be used,
I noticed that there are two places where we can end up calling
device_online()/device_offline() - online_pages()/offline_pages() without
the mem_hotplug_lock. And there are other places where we call
device_online()/device_offline() without the device_hotplug_lock.
While e.g.
echo "online" > /sys/devices/system/memory/memory9/state
is fine, e.g.
echo 1 > /sys/devices/system/memory/memory9/online
Will not take the mem_hotplug_lock. However the device_lock() and
device_hotplug_lock.
E.g. via memory_probe_store(), we can end up calling
add_memory()->online_pages() without the device_hotplug_lock. So we can
have concurrent callers in online_pages(). We e.g. touch in
online_pages() basically unprotected zone->present_pages then.
Looks like there is a longer history to that (see Patch #2 for details),
and fixing it to work the way it was intended is not really possible. We
would e.g. have to take the mem_hotplug_lock in device/base/core.c, which
sounds wrong.
Summary: We had a lock inversion on mem_hotplug_lock and device_lock().
More details can be found in patch 3 and patch 6.
I propose the general rules (documentation added in patch 6):
1. add_memory/add_memory_resource() must only be called with
device_hotplug_lock.
2. remove_memory() must only be called with device_hotplug_lock. This is
already documented and holds for all callers.
3. device_online()/device_offline() must only be called with
device_hotplug_lock. This is already documented and true for now in core
code. Other callers (related to memory hotplug) have to be fixed up.
4. mem_hotplug_lock is taken inside of add_memory/remove_memory/
online_pages/offline_pages.
To me, this looks way cleaner than what we have right now (and easier to
verify). And looking at the documentation of remove_memory, using
lock_device_hotplug also for add_memory() feels natural.
This patch (of 6):
remove_memory() is exported right now but requires the
device_hotplug_lock, which is not exported. So let's provide a variant
that takes the lock and only export that one.
The lock is already held in
arch/powerpc/platforms/pseries/hotplug-memory.c
drivers/acpi/acpi_memhotplug.c
arch/powerpc/platforms/powernv/memtrace.c
Apart from that, there are not other users in the tree.
Link: http://lkml.kernel.org/r/20180925091457.28651-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The free_bootmem_late and memblock_free_late do exactly the same thing:
they iterate over a range and give pages to the page allocator.
Replace calls to free_bootmem_late with calls to memblock_free_late and
remove the bootmem variant.
Link: http://lkml.kernel.org/r/1536927045-23536-25-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The free_bootmem and free_bootmem_node are merely wrappers for
memblock_free. Replace their usage with a call to memblock_free using the
following semantic patch:
@@
expression e1, e2, e3;
@@
(
- free_bootmem(e1, e2)
+ memblock_free(e1, e2)
|
- free_bootmem_node(e1, e2, e3)
+ memblock_free(e2, e3)
)
Link: http://lkml.kernel.org/r/1536927045-23536-24-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The alloc_bootmem(size) is a shortcut for allocation of SMP_CACHE_BYTES
aligned memory. When the align parameter of memblock_alloc() is 0, the
alignment is implicitly set to SMP_CACHE_BYTES and thus alloc_bootmem(size)
and memblock_alloc(size, 0) are equivalent.
The conversion is done using the following semantic patch:
@@
expression size;
@@
- alloc_bootmem(size)
+ memblock_alloc(size, 0)
Link: http://lkml.kernel.org/r/1536927045-23536-22-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The alloc_bootmem_pages() function allocates PAGE_SIZE aligned memory.
memblock_alloc() with alignment set to PAGE_SIZE does exactly the same
thing.
The conversion is done using the following semantic patch:
@@
expression e;
@@
- alloc_bootmem_pages(e)
+ memblock_alloc(e, PAGE_SIZE)
Link: http://lkml.kernel.org/r/1536927045-23536-20-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The alloc_bootmem_pages_nopanic(size) is a shortcut for
__alloc_bootmem_nopanic(size, PAGE_SIZE, BOOTMEM_LOW_LIMIT) which allocates
PAGE_SIZE aligned memory. Since BOOTMEM_LOW_LIMIT is hardwired to 0 there
is no restrictions on where the allocated memory should reside.
The memblock_alloc_nopanic(size, PAGE_SIZE) also allocates PAGE_SIZE
aligned memory without any restrictions and thus can be used as a
replacement for alloc_bootmem_pages_nopanic()
Link: http://lkml.kernel.org/r/1536927045-23536-12-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
