| Age | Commit message (Collapse) | Author |
|---|
|
The 64-bit data field in a transaction is not used for commands.
And the opcode array is *only* used for commands. They're
(currently) the same size; save a little space in the transaction
structure by enclosing the two fields in a union.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipa_cmd_info structure now contains only one field, and it's an
enumerated type whose values all fit in 8 bits. Currently we'll
never use more than 8 TREs in a command transaction, and we can
represent that number of command opcodes in the same space as a 64
bit pointer to an ipa_cmd_info structure.
Define IPA_COMMAND_TRANS_TRE_MAX as the maximum number of TREs that
can be in a command transaction. Replace the info pointer in a
transaction with a fixed-size array named cmd_opcode[] of that many
bytes. Store the opcode in this array when adding a command TRE to
a transaction, as was done previously for the info array. This
makes the ipa_cmd_info unused, so get rid of it.
When committing an immediate command transaction, use the channel's
Boolean command flag to determine whether to fill in the opcode,
which will be taken (as before) from the array in the transaction.
This makes the command info pool unnecessary, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer use the direction argument for gsi_trans_cmd_add(), so
get rid of it in its definition, and in its seven callers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The direction field of the ipa_cmd_info structure is set, but never
used. It seems it might have been used for the DMA_SHARED_MEM
immediate command, but the DIRECTION flag is set based on the value
of the passed-in direction flag there.
Anyway, remove this unused field from the ipa_cmd_info structure.
This is done as a separate patch to make it very obvious that it's
not required.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ipa_endpoint_modem_exception_reset_all(), a high estimate was
made of the number of endpoints that need their status register
updated. We only used what was needed, so the high estimate didn't
matter much.
However the next few patches are going to limit the number of
commands in a single transaction, and the overestimate would exceed
that. So count the number of modem TX endpoints at initialization
time, and use it in ipa_endpoint_modem_exception_reset_all().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the beginning gsi_trans_commit_wait_timeout() has existed to
provide a way to allow waiting a limited time for a transaction
to complete. But that function has never been used.
In fact, there is no use for this function, because a transaction
committed to hardware should *always* complete. The only reason it
might not complete is if there were a hardware failure, or perhaps a
system configuration error.
Furthermore, if a timeout ever did occur, the IPA hardware would be
in an indeterminate state, from which there is no recovery. It
would require some sort of complete IPA reset, and would require the
participation of the modem, and at this time there is no such
sequence defined.
So get rid of the definition of gsi_trans_commit_wait_timeout(), and
update a few comments accordingly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't assume that a 500 microsecond time limit should be used for
all receive endpoints that support aggregation. Instead, specify
the time limit to use in the configuration data.
Set a 500 microsecond limit for all existing RX endpoints, as before.
Checking for overflow for the time limit field is a bit complicated.
Rather than duplicate a lot of code in ipa_endpoint_data_valid_one(),
call WARN() if any value is found to be too large when encoding it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new flag for AP receive endpoints that indicates whether
a "hard limit" is used as a criterion for closing aggregation.
Add comments explaining the difference between "hard" and "soft"
aggregation limits.
Pass a flag to ipa_aggr_size_kb() so it computes the proper
aggregation size value whether using hard or soft limits. Move
that function earlier in "ipa_endpoint.c" so it can be used
without a forward-reference.
Update ipa_endpoint_data_valid_one() so it validates endpoints whose
data indicate a hard aggregation limit is used, and so it reports
set aggregation flags for endpoints without aggregation enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new Boolean flag for RX endpoints defining whether HOLB drop
is initially enabled or disabled for the endpoint. All existing AP
endpoints should have HOLB drop disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistakes (triple letters) in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GCC array-bounds warns that ipc_coredump_get_list() under-allocates
the size of struct iosm_cd_table *cd_table.
This is avoidable - we just need a flexible array. Nothing calls
sizeof() on struct iosm_cd_list or anything that contains it.
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Link: https://lore.kernel.org/r/20220520060013.2309497-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
align the extack argument of the ocelot_port_fdb_del()
function.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Link: https://lore.kernel.org/r/20220520002040.4442-1-eng.alaamohamedsoliman.am@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The continuation line does not align with the opening bracket
and this patch fix it.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Link: https://lore.kernel.org/r/20220520003614.6073-1-eng.alaamohamedsoliman.am@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GCC array bounds checking complains that ulp_id is validated
only against upper bound. Make it unsigned.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220520061955.2312968-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sometimes t7xx_cldma_gpd_set_next_ptr() is called under spin lock,
so add 'gfp_mask' parameter in t7xx_cldma_gpd_set_next_ptr() to pass
the flag.
Fixes: 39d439047f1d ("net: wwan: t7xx: Add control DMA interface")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20220519032108.2996400-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typo which breaks build for parisc.
Fixes: 3daebfbeb455 ("net: tulip: convert to devres")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/all/CA+G9fYuCzU5VZ_nc+6NEdBXJdVCH=J2SB1Na1G_NS_0BNdGYtg@mail.gmail.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Link: https://lore.kernel.org/r/4719560.GXAFRqVoOG@eto.sf-tec.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Siena only supports software TSO. This means more code can be deleted,
as pointed out by the Smatch static checker warning:
drivers/net/ethernet/sfc/siena/tx.c:184 __efx_siena_enqueue_skb()
warn: duplicate check 'segments' (previous on line 158)
Fixes: 956f2d86cb37 ("sfc/siena: Remove build references to missing functionality")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/kernel-janitors/YoH5tJMnwuGTrn1Z@kili/
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/165294463549.23865.4557617334650441347.stgit@palantir17.mph.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All elements of the default endpoint configuration are used in the
code when programming an endpoint for use. But none of the other
configuration data is ever needed once things are initialized.
So rather than saving a pointer to *all* of the configuration data,
save a copy of only the endpoint configuration portion.
This will eventually allow endpoint configuration to be modifiable
at runtime. But even before that it means we won't keep a pointer
to configuration data after when no longer needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the just-moved data structure types to drop the "_data"
suffix, to make it more obvious they are no longer meant to be used
just as read-only initialization data. Rename the fields and
variables of these types to use "config" instead of "data" in the
name. This is another small step meant to facilitate review.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the definitions of the structures defining endpoint-specific
configuration data out of "ipa_data.h" and into "ipa_endpoint.h".
This is a trivial movement of code without any other change, to
prepare for the next few patches.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
About half of the fields set by the call in ipa_modem_netdev_setup()
are overwritten after the call. Instead, just skip the call, and
open-code the (other) assignments it makes to the net_device
structure fields.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we program an RX endpoint to have no header (header length is 0),
header-related endpoint configuration values are meaningless and are
ignored.
The only case we support that defines a header is QMAP endpoints.
In ipa_endpoint_init_hdr_ext() we set the endianness mask value
unconditionally, but it should not be done if there is no header
(meaning it is not configured for QMAP).
Set the endianness conditionally, and rearrange the logic in that
function slightly to avoid testing the qmap flag twice.
Delete an incorrect comment in ipa_endpoint_init_aggr().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CHANNEL_NOT_RUNNING error condition has been generalized, so
rename it to be INCORRECT_CHANNEL_STATE.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In gsi_channel_update(), a reference count is taken on the last
completed transaction "to keep it from completing" before we give
the event back to the hardware. Completion processing for that
transaction (and any other "new" ones) will not occur until after
this function returns, so there's no risk it completing early. So
there's no need to take and drop the additional transaction
reference.
Use local variables in the call to gsi_evt_ring_doorbell().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I missed this in the barrage of GCC 12 warnings. Commit cf2df74e202d
("net: fix dev_fill_forward_path with pppoe + bridge") changed
the pointer into an array.
Fixes: d7e6f5836038 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Link: https://lore.kernel.org/r/20220520012555.2262461-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GCC 12 seems upset that we check ipa_irq against array bound
but then proceed, anyway:
drivers/net/ipa/ipa_interrupt.c: In function ‘ipa_interrupt_add’:
drivers/net/ipa/ipa_interrupt.c:196:27: warning: array subscript 30 is above array bounds of ‘void (*[30])(struct ipa *, enum ipa_irq_id)’ [-Warray-bounds]
196 | interrupt->handler[ipa_irq] = handler;
| ~~~~~~~~~~~~~~~~~~^~~~~~~~~
drivers/net/ipa/ipa_interrupt.c:42:27: note: while referencing ‘handler’
42 | ipa_irq_handler_t handler[IPA_IRQ_COUNT];
| ^~~~~~~
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220519004417.2109886-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GCC 12 warns:
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c: In function ‘ipc_protocol_dl_td_process’:
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c:406:13: warning: the comparison will always evaluate as ‘true’ for the address of ‘cb’ will never be NULL [-Waddress]
406 | if (!IPC_CB(skb)) {
| ^
Indeed the check seems entirely pointless. Hopefully the other
validation checks will catch if the cb is bad, but it can't be
NULL.
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Link: https://lore.kernel.org/r/20220519004342.2109832-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gswip_port_fdb_dump() reads the MAC bridge entries. The error message
should say "failed to read mac bridge entry". While here, also add the
index to the error print so humans can get to the cause of the problem
easier.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The first N entries in priv->vlans are reserved for managing ports which
are not part of a bridge. Use priv->hw_info->max_ports to consistently
access per-bridge entries at index 7. Starting at
priv->hw_info->cpu_port (6) is harmless in this case because
priv->vlan[6].bridge is always NULL so the comparison result is always
false (which results in this entry being skipped).
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
t7xx_request_irq() error: uninitialized symbol 'ret'.
t7xx_core_hk_handler() error: potentially dereferencing uninitialized 'event'.
If the condition to enter the loop that waits for the handshake event
is false on the first iteration then the uninitialized 'event' will be
dereferenced, fix this by initializing 'event' to NULL.
t7xx_port_proxy_recv_skb() warn: variable dereferenced before check 'skb'.
No need to check skb at t7xx_port_proxy_recv_skb() since we know it
is always called with a valid skb by t7xx_cldma_gpd_rx_from_q().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Link: https://lore.kernel.org/r/20220518195529.126246-1-ricardo.martinez@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Partially convert mtk_eth_soc to phylink_pcs, moving the configuration,
link up and AN restart over. However, it seems mac_pcs_get_state()
doesn't actually get the state from the PCS, so we can't convert that
over without a better understanding of the hardware.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a mtk_pcs structure which encapsulates everything that the PCS
functions need (the regmap and ana_rgc3 offset), and use this in the
PCS functions. Provide shim functions to convert from the existing
"mtk_sgmii_*" interface to the converted PCS functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SGMIISYS configuration is performed while ETHSYS_SYSCFG0 is in a
disabled state. In order to preserve this when we switch to phylink_pcs
we need to move the restoration of this register to the mac_finish()
callback.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the setting of the MTK_MAC_MCR register from the end of mac_config
into the phylink mac_finish() method, to keep it as the very last write
that is done during configuration.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a fixme comment for the last remaining incorrect usage of
state->speed in the mac_config() method, which is strangely in a code
path which is only run when the PHY interface mode changes.
This means if we are in RGMII mode, changes in state->speed will not
cause the INTF_MODE, TRGMII_RCK_CTRL and TRGMII_TCK_CTRL registers to
be set according to the speed, nor will the TRGPLL clock be set to the
correct value.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide mtk_sgmii_config() to wrap up the decisions about which SGMII
configuration will be called.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that mtk_sgmii_setup_mode_force() only uses the interface mode
from the phylink state, pass just the interface mode into this
function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Phylink does not guarantee that state->duplex will be set correctly in
the mac_config() call, so it's a bug that the driver makes use of it.
Move the 802.3z PCS duplex configuration to mac_link_up().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Phylink does not guarantee that state->speed will be set correctly in
the mac_config() call, so it's a bug that the driver makes use of it.
Moreover, it is making use of it in a function that is only ever called
for 1000BASE-X and 2500BASE-X which operate at a fixed speed which
happens to be the same setting irrespective of the interface mode. We
can simply remove the switch statement and just set the SGMII interface
speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCS speed setting is a two bit field, but it is defined as two
separate bits. Add a bitfield mask for the speed definitions, an
use the FIELD_PREP() macro to define each PCS speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "flags" member of struct mtk_sgmii appears to be unused, as are
the MTK_SGMII_PHYSPEED_* and MTK_HAS_FLAGS() macros. Remove them.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mac->mode is only ever written to in one location, and is thus
superflous. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The netif_receive_skb() function frees "skb" so store skb->len before
it is freed.
Fixes: fd3040b9394c ("net: ethernet: Add driver for Sunplus SP7021")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YoUuy4iTjFAcSn03@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Lenovo Thunderbolt 4 Dock, and other Lenovo USB Docks are using the
original Realtek USB ethernet Vendor and Product IDs
If the Network device is Realtek verify that it is on a Lenovo USB hub
before enabling the passthru feature
This also adds in the device IDs for the Lenovo USB Dongle and one other
USB-C dock
V2 fix formating of code
V3 remove Generic define for Device ID 0x8153 and change it to use value
V4 rearrange defines and case statement to put them in better order
v5 create helper function to do the testing work as suggested
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20220517180539.25839-1-dober6023@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
