summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-05-01bnx2x: Prevent memory leak when cnic is absentYuval Mintz
bnx2x driver allocates searcher T2 tables, but it releases that memory during unload only released if the cnic is loaded. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-01bnx2x: correct reading of speed capabilitiesYaniv Rosner
When the bnx2x driver reads the port configuration - mask irrelevant bits. Without this change, the unintended bits may cause the driver to needlessly toggle the link, as a comparison in the link flap avoidance flow will show that the old link did not advertise the same capabilities and thus cannot be retained. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30mlx4_en: fix a build error on 32bit archesEric Dumazet
commit b6c39bfcf1d7d63 ("net/mlx4_en: Add a service task") added a build error on 32bit arches. ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined! Fix this problem by using do_div() Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Cc: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30Revert "bnx2x: allow nvram test to run when device is down"Dmitry Kravkov
This reverts commit d2d2d87dfd1a25ee270994c5b9e3eb4690428d32 ("bnx2x: allow nvram test to run when device is down"). Since it makes access to the device in D3 state possible. More work is required to make sure device is not set to D3 during ifdown. Until this is done the nvram-test should simply exit if device is down like it did before. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30drivers: net: cpsw: fix kernel warn on cpsw irq enableMugunthan V N
With the commit a11fbba (net/cpsw: fix irq_disable() with threaded interrupts) from Sebastian Siewior, a kernel warning is generated as below. This warning is generated as the irq_enabled is not initialized for the primary interface and in probe it is initialized for the second interface. This patch moves irq_enabled initialization from second interface to primary interface. [ 3.049173] net eth0: phy found : id is : 0x4dd074 [ 3.054552] net eth0: phy found : id is : 0x4dd074 [ 3.070421] ------------[ cut here ]------------ [ 3.075308] WARNING: at kernel/irq/manage.c:437 enable_irq+0x3c/0x74() [ 3.082173] Unbalanced enable for IRQ 56 [ 3.086299] Modules linked in: [ 3.089557] [<c001abcc>] (unwind_backtrace+0x0/0xf0) from [<c004294c>] (warn_slowpath_common+0x4c/0x68) [ 3.099450] [<c004294c>] (warn_slowpath_common+0x4c/0x68) from [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) [ 3.109521] [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) from [<c00a29fc>] (enable_irq+0x3c/0x74) [ 3.118681] [<c00a29fc>] (enable_irq+0x3c/0x74) from [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) [ 3.127669] [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) from [<c0445c08>] (__dev_open+0x9c/0xf8) [ 3.136646] [<c0445c08>] (__dev_open+0x9c/0xf8) from [<c0445e34>] (__dev_change_flags+0x78/0x13c) [ 3.145988] [<c0445e34>] (__dev_change_flags+0x78/0x13c) from [<c0445f64>] (dev_change_flags+0x10/0x48) [ 3.155884] [<c0445f64>] (dev_change_flags+0x10/0x48) from [<c0736d88>] (ip_auto_config+0x198/0x111c) [ 3.165592] [<c0736d88>] (ip_auto_config+0x198/0x111c) from [<c00086a4>] (do_one_initcall+0x34/0x180) [ 3.175309] [<c00086a4>] (do_one_initcall+0x34/0x180) from [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) [ 3.185393] [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) from [<c04f36ec>] (kernel_init+0x8/0xe4) [ 3.194929] [<c04f36ec>] (kernel_init+0x8/0xe4) from [<c00133d0>] (ret_from_fork+0x14/0x24) [ 3.203712] ---[ end trace d6f979da080bc391 ]--- Cc: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30sh_eth: use random MAC address if no valid one suppliedSergei Shtylyov
On Renesas R-Car based development boards, although a MAC address is printed on all the Ethernet port labels, U-Boot doesn't write a valid MAC address to the Ether MAHR/MALR registers (there's no storage provided for the Ether MAC address either), so we have to resort to using a random MAC address... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-303c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)Matthew Whitehead
The venerable 3c509 driver only sets its device parent in one case, the ISAPnP one. It does this with the SET_NETDEV_DEV function. It should register with the device hierarchy in two additional cases: standard (non-PnP) ISA and EISA. - Currently they appear here: /sys/devices/virtual/net/eth0 (standard ISA) /sys/devices/virtual/net/eth1 (EISA) - Rather, they should instead be here: /sys/devices/isa/3c509.0/net/eth0 (standard ISA) /sys/devices/pci0000:00/0000:00:07.0/00:04/net/eth1 (EISA) Tested on ISA and EISA boards. Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30tg3: fix to append hardware time stamping flagsFlavio Leitner
The commit f233a976ad15c3b8c54c0157f3c41d23f7514279 (tg3: shows HW time stamping support only if ptp_capable is present) didn't append hardware flags correctly. This patch fixes it. Signed-off-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c drivers/net/ethernet/emulex/benet/be.h include/net/tcp.h net/mac802154/mac802154.h Most conflicts were minor overlapping stuff. The be2net driver brought in some fixes that added __vlan_put_tag calls, which in net-next take an additional argument. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-30Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next John W. Linville says: ==================== A few more stragglers intended for 3.10... For the Bluetooth bits, Gustavo says: "A few more patches intended for 3.10, the most important one is the support in btusb for fw loading for the Intel Bluetooth device. Other than that we have only fixes and clean ups." For the iwlwifi bits, Johannes says: "Here are a few more changes for the 3.10 stream, some bugfixes, adjustments to some powersave parameters and a new device ID." For the NFC bits, Samuel says: "This pull request includes Marcel's Kconfig dependency fix on top of the LLCP code move to net/nfc." On top of that...Yogesh Ashok Powar provides a few PCI-related mwifiex updates, Hauke Mehrtens provides a small ssb feature for spurious tone avoidance on a specific chip, and Larry Finger provides a small rtlwifi fix related to avoiding false detection of AP loss. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2013-04-29bnx2x: allow handling tunnel over udp offloadDmitry Kravkov
CC: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: do not set SKB_GSO_UDPDmitry Kravkov
Since SKB_GSO_* flags are set by appropriate gso_segment callback in TCP/UDP layer. CC: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29cxgb4vf: Support CPL_SGE_EGR_UPDATEs encapsulated in a CPL_FW4_MSGVipul Pandya
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a CPL_FW4_MSG as follows flit0 rss_header (if DropRSS == 0 in IQ context) flit1 CPL_FW4_MSG cpl flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE flit3 CPL_SGE_EGR_UPDATE cpl So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle both. This patch also writes a new parameter to firmware requesting encapsulated EGR_UPDATE. This allows firmware with this support to not break older drivers. Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29cxgb4: Support CPL_SGE_EGR_UPDATEs encapsulated in a CPL_FW4_MSGVipul Pandya
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a CPL_FW4_MSG as follows flit0 rss_header (if DropRSS == 0 in IQ context) flit1 CPL_FW4_MSG cpl flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE flit3 CPL_SGE_EGR_UPDATE cpl So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle both. This patch also writes a new parameter to firmware requesting encapsulated EGR_UPDATE. This allows firmware with this support to not break older drivers. Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29cxgb4: Fix pci_device_id structure initialization with correct PF numberVipul Pandya
Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29tg3: shows HW time stamping support only if ptp_capable is presentFlavio Leitner
Current tg3 shows hardware timestamping support for all devices when that is true only for the hardware with PTP_CAPABLE flag present. Signed-off-by: Flavio Leitner <fbl@redhat.com> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29be2net: FLR must be first cmd issued to Lancer FWKalesh AP
Lancer FW requires that the first cmd issued by the host-driver be an FLR. So, re-order be_probe() to move be_cmd_function_reset() ahead of be_cmd_fw_init(). Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29be2net: Use GET_FUNCTION_CONFIG V1 cmdKalesh AP
Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for querrying resources available per function. Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29sh_eth: add R8A77781 supportSergei Shtylyov
Add support for another ARM member of the R-Car family, R-Car M1A, also known as R8A77781 -- it will share the code with previously added R8A77790. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29r8169: fix 8168evl frame padding.Stefan Bader
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29hyperv: Fix a compiler warning in netvsc_send()Haiyang Zhang
Fixed: warning: cast from pointer to integer of different size The Hyper-V hosts always use 64 bit request id. The guests can have 32 or 64 bit pointers which equal to the ulong type size. So we cast it to ulong type. And, assigning 32bit integer to 64 bit variable works fine. The VMBus returns the same id in the completion packet. But the value has no effect on the host side. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29drivers: net: usb: pegasus: fix control urb submissionPetko Manolov
Pegasus driver used single callback for sync and async control URBs. Special flags were employed to distinguish between both, but due to flawed logic it didn't always work. As a result of this change [get|set]_registers() are now much simpler. Async write is also leaner and does not use single, statically allocated memory for usb_ctrlrequest, which is another potential race when asynchronously submitting URBs. Signed-off-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29drivers: net: usb: pegasus: read/write_mii_word optimisedPetko Manolov
Duplicated code in routines reading and writing MII registers is now packed in __mii_op(). Signed-off-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29drivers: net: usb: pegasus: remove skb poolPetko Manolov
The socket buffer pool for the receive path is now gone. It's existence didn't make much difference (performance-wise) and the code is better off without the spinlocks protecting it. Signed-off-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29atm: he: use mdelay instead of large udelay constantsArnd Bergmann
ARM cannot handle udelay for more than 2 miliseconds, and it is rather bad style to block the cpu for 16ms anyway, so let's use msleep instead. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Chas Williams <chas@cmf.nrl.navy.mil> Cc: linux-atm-general@lists.sourceforge.net Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29be2net: Fix to show wol disabled/enabled state correctly.Sarveshwar Bandi
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29be2net: Fixed memory leakSuresh Reddy
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: allow choosing destination port per vxlanstephen hemminger
Allow configuring the default destination port on a per-device basis. Adds new netlink paramater IFLA_VXLAN_PORT to allow setting destination port when creating new vxlan. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: compute source port in network byte orderstephen hemminger
Rather than computing source port and returning it in host order then swapping later, go ahead and compute it in network order to start with. Cleaner and less error prone. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: source compatiablity with IFLA_VXLAN_GROUP (v2)stephen hemminger
Source compatiability for build iproute2 was broken by: commit c7995c43facc6e5dea4de63fa9d283a337aabeb1 Author: Atzm Watanabe <atzm@stratosphere.co.jp> vxlan: Allow setting destination to unicast address. Since this commit has not made it upstream (still net-next), and better to avoid gratitious changes to exported API's; go back to original definition, and add a comment. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: fix byte order issues with NDA_PORTstephen hemminger
The NDA_PORT attribute was added, but the author wasn't careful about width (port is 16 bits), or byte order. The attribute was being dumped as 16 bits, but only 32 bit value would be accepted when setting up a device. Also, the remote port is in network byte order and was being compared with default port in host byte order. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: document UDP default portstephen hemminger
The default port for VXLAN is not same as IANA value. Document this. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29vxlan: update mail address and copyright datestephen hemminger
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-29net: tun: release the reference of tun device in tun_recvmsgGao feng
We forget to release the reference of tun device in tun_recvmsg. bug introduced in commit 54f968d6efdbf7dec36faa44fc11f01b0e4d1990 (tuntap: move socket to tun_file) Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next Jeff Kirsher says: ==================== This series contains updates to e1000e, igb and ixgbe. There are 2 patches in this series which could be applied to net, but since Linus is so very close to releasing 3.9, I do not think it prudent to try and push these into net at this time. I have CC'd stable on these patches so that they can queue them up as soon as 3.9 gets released. The 2 patches are: e1000e: fix numeric overflow in phc settime method ixgbe: fix EICR write in ixgbe_msix_other Richard provides a fix for e1000e by using a helper function from time.h to resolve a unintended overflow in the PTP settime function. Bruce provides a fix to wait for NAPI to be done with the current context after disabling interrupts and then disable NAPI when the interface is going down. This fixes a possible "unable to handle kernel paging request" panic in net-next. Andi Kleen provides a patch for igb to use mdelay instead of udelay when we needed 100000us. Jacob provides a fix for ixgbe to simply mask the lower 16bits off so that ixgbe_msix_other does not write them in the EICR, which causes them to remain high and be properly handled by the clean_rings interrupt routine as normal. Emil cleans up the logic in ixgbe_setup_loopback_test() to only access registers applicable to the MAC type. In addition, removes majority of the AUTOC register reads by using a cached value instead to avoid writing corrupted values to AUTOC due to bad FW. Emil also add support for disabling link during boot time. Lastly, he provides a patch which adds the MAC type to the version in ethtool_regs which will make it easier to check the MAC type when dumping registers with ethtool. There is a separate ethtool tool patch which is dependent upon Emil's last patch of the series to add the MAC type to the version in ethtool_regs, which will be sent separately. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add support to get VF configRony Efraim
Support getting VF config. Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add VF MAC spoof checking supportRony Efraim
Add ndo_set_vf_spoofchk support Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add set VF default vlan ID and priority supportRony Efraim
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport is considered to be in VST mode. In this mode, the PPF driver configures Ethernet QPs created by this VF to use this vlan id and priority. Currently RoCE isn't supported on that mode. The special values of VID=4095 or VID=0,UP=0 are considered as VGT. Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add set VF mac address supportRony Efraim
Add ndo_set_vf_mac support which allows to set the MAC address for mlx4 VF Ethernet NICs from the host. Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add structures to keep VF Ethernet ports informationRony Efraim
This patch add struct mlx4_vport_state where all the parameters related to management of VFs port (virtual ports of the NIC eswitch) are kept. The driver keeps an administrative and operational copy of the settings. The current administrative copy becomes operational on the event of probing a VF either on a VM or on the host. Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4: Add reference counting to MAC registerationRony Efraim
Add reference counting to the driver MAC registeration code. This would be needed for cases where a mac is registered from more than once, e.g when both the host and the VM driver register the same mac, the host for mac spoof protection purposes and the VM for its regular needs. Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4_en: Disable HW clock overflow check when no HW supportAmir Vadai
Should not run HW clock overflow check if HW clock is not supported. Also, since this watchdog is the only customer of service_task, no need to start it in that case. Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26net/mlx4_core: Disable HW timestamping for VFsAmir Vadai
Disable timestamp capability on virtual functions. Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26be2net: Avoid diagnostic test in certain versions of firmware to avoid NIC ↵Suresh Reddy
freeze. Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26be2net: Renamed rx_address_mismatch_errors to rx_address_filteredSuresh Reddy
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26be2net: Add support for setting and getting rx flow hash optionsSuresh Reddy
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com> Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26rtlwifi: rtl8192cu: Fix false loss of AP indicationLarry Finger
A major change in the rtlwifi family recently added code to detect when there is loss of AP signals. One critical statement needed for the USB driver was missed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-26brcmsmac: Fix merge issuePiotr Haber
Commit 7088f4835aa353f7226e57e73fd9e6564a4dfb75 "Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless" ramoved call to brcms_led_unregister in mac80211_if.c Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-26ssb: implement ssb spuravoid for chipid BCM43222Hauke Mehrtens
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>