| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit f69115fdbc1ac0718e7d19ad3caa3da2ecfe1c96 ]
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 08c5cd37480f59ea39682f4585d92269be6b1424 ]
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit f190fd92458da3e869b4e2c6289e2c617490ae53 ]
This patch adds support for Infineon flashloader 0x8087/0x0801.
The flashloader is used in Telit LE940B modem family with Telit
flashing application.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit bcf42aa60c2832510b9be0f30c090bfd35bb172d ]
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 519d8bd4b5d3d82c413eac5bb42b106bb4b9ec15 ]
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
Fixes: d5c6a1e024dd ("usb: renesas_usbhs: fixup interrupt status clear method")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 40d9c32525cba79130612650b1abc47c0c0f19a8 ]
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 6695593e4a7659db49ac6eca98c164f7b5589f72 ]
Add support for WeTelecom WM-D200.
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22de ProdID=6801 Rev=00.00
S: Manufacturer=WeTelecom Incorporated
S: Product=WeTelecom Mobile Products
C: #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 53e5f36fbd2453ad69a3369a1db62dc06c30a4aa ]
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 3b7c7e52efda0d4640060de747768360ba70a7c0 ]
There is an allocation with GFP_KERNEL flag in mos7840_write(),
while it may be called from interrupt context.
Follow-up for commit 191252837626 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 5a5a1d614287a647b36dff3f40c2b0ceabbc83ec ]
There is an allocation with GFP_KERNEL flag in mos7720_write(),
while it may be called from interrupt context.
Follow-up for commit 191252837626 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 88716a93766b8f095cdef37a8e8f2c93aa233b21 ]
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 33be126510974e2eb9679f1ca9bca4f67ee4c4c7 ]
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit add125054b8727103631dce116361668436ef6a7 ]
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 539587511835ea12d8daa444cbed766cf2bc3612 ]
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 7c705dfe2ebe731c8fd068623b6b4df2d3512c08 ]
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit e5b36ae2f851024d43c76e51f395d32ce8d769ce ]
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit c7de573471832dff7d31f0c13b0f143d6f017799 ]
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 6bb47e8ab98accb1319bd43c64966340ba3bba9a ]
Memory leak and unbalanced reference count:
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef9775 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
unreferenced object 0xffffffc08af5b800 (size 1024):
comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
hex dump (first 32 bytes):
30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff 0h..............
01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff ..........}@....
backtrace:
[<ffffffc0003079ec>] create_object+0x148/0x2a0
[<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
[<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
[<ffffffc0006fa610>] hub_probe+0x120/0xb84
[<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
[<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
[<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
[<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
[<ffffffc0005d23a4>] device_add+0x324/0x604
[<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
[<ffffffc00070a350>] generic_probe+0x44/0x84
[<ffffffc000702914>] usb_probe_device+0x54/0x74
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
Deadlocks:
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
CC: <stable@vger.kernel.org> #4.4+
Fixes: e50293ef9775 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 647024a7df36014bbc4479d92d88e6b77c0afcf6 ]
udriver struct allocated by kzalloc() will not be freed
if usb_register() and next calls fail. This patch fixes this
by adding one more step with kfree(udriver) in error path.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 01d7956b58e644ea0d2e8d9340c5727a8fc39d70 ]
This patch adds a set of compositions for Telit LE920A4.
Compositions in short are:
0x1207: tty + tty
0x1208: tty + adb + tty + tty
0x1211: tty + adb + ecm
0x1212: tty + adb
0x1213: ecm + tty
0x1214: tty + adb + ecm + tty
telit_le922_blacklist_usbcfg3 is reused for compositions 0x1211
and 0x1214 due to the same interfaces positions.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit ae34d12cc1e212ffcd92e069030e54dae69c832f ]
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 6977495c06f7f47636a076ee5a0ca571279d9697 ]
Ivium Technologies uses the FTDI VID with custom PIDs for their line of
electrochemical interfaces and the PalmSens they developed for PalmSens
BV.
Signed-off-by: Robert Delien <robert@delien.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit cf1b18030de29e4e5b0a57695ae5db4a89da0ff7 ]
The device has four interfaces; the three serial ports ought to be
handled by this driver:
00 Diagnostic interface serial port
01 NMEA device serial port
02 Mass storage (sd card)
03 Modem serial port
The other product ids listed in the Windows driver are present already.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 3c0415fa08548e3bc63ef741762664497ab187ed ]
This patch adds support for 0x1206 PID of Telit LE910.
Since the interfaces positions are the same than the ones for
0x1043 PID of Telit LE922, telit_le922_blacklist_usbcfg3 is used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 25b1f9acc452209ae0fcc8c1332be852b5c52f53 ]
BugLink: http://bugs.launchpad.net/bugs/1498667
As reported in BugLink, this device has an issue with Linux Power
Management so adding a quirk. This quirk was reccomended by Alan Stern:
http://lkml.iu.edu/hypermail/linux/kernel/1606.2/05590.html
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit df36c5bede207f734e4750beb2b14fb892050280 ]
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 15e4292a2d21e9997fdb2b8c014cc461b3f268f0 ]
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
Fixes: 97664a207bc2 ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 4fdef698383db07d829da567e0e405fc41ff3a89 ]
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 9b53d9af7aac09cf249d72bfbf15f08e47c4f7fe ]
This patch fixes the setup sequence in xfer_work(). Otherwise,
sometimes a usb transaction will get stuck.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit 9cad39fe4e4a4fe95d8ea5a7b0692b0a6e89e38b ]
commit f3af36511e60 ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e60 ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
|
|
[ Upstream commit b348d7dddb6c4fbfc810b7a0626e8ec9e29f7cbb ]
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit ab2a4bf83902c170d29ba130a8abb5f9d90559e1 ]
The USB core contains a bug that can show up when a USB-3 host
controller is removed. If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.
The problem was described in graphical form by Chung-Geol Kim, who
first reported it:
=================================================
At *remove USB(3.0) Storage
sequence <1> --> <5> ((Problem Case))
=================================================
VOLD
------------------------------------|------------
(uevent)
________|_________
|<1> |
|dwc3_otg_sm_work |
|usb_put_hcd |
|peer_hcd(kref=2)|
|__________________|
________|_________
|<2> |
|New USB BUS #2 |
| |
|peer_hcd(kref=1) |
| |
--(Link)-bandXX_mutex|
| |__________________|
|
___________________ |
|<3> | |
|dwc3_otg_sm_work | |
|usb_put_hcd | |
|primary_hcd(kref=1)| |
|___________________| |
_________|_________ |
|<4> | |
|New USB BUS #1 | |
|hcd_release | |
|primary_hcd(kref=0)| |
| | |
|bandXX_mutex(free) |<-
|___________________|
(( VOLD ))
______|___________
|<5> |
| SCSI |
|usb_put_hcd |
|peer_hcd(kref=0) |
|*hcd_release |
|bandXX_mutex(free*)|<- double free
|__________________|
=================================================
This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.
This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released. The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit ea1d39a31d3b1b6060b6e83e5a29c069a124c68a ]
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit f8a15a9650694feaa0dabf197b0c94d37cd3fb42 ]
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 7b2c17f829545df27a910e8d82e133c21c9a8c9c ]
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit f3eec0cf784e0d6c47822ca6b66df3d5812af7e6 ]
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit d95815ba6a0f287213118c136e64d8c56daeaeab ]
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 32cb0b37098f4beeff5ad9e325f11b42a6ede56c ]
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 81099f97bd31e25ff2719a435b1860fc3876122f ]
Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit de95c40d5beaa47f6dc8fe9ac4159b4672b51523 ]
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 3425aa03f484d45dc21e0e791c2f6c74ea656421 ]
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit d246dcb2331c5783743720e6510892eb1d2801d9 ]
[ 40.467381] =============================================
[ 40.473013] [ INFO: possible recursive locking detected ]
[ 40.478651] 4.6.0-08691-g7f3db9a #37 Not tainted
[ 40.483466] ---------------------------------------------
[ 40.489098] usb/733 is trying to acquire lock:
[ 40.493734] (&(&dev->lock)->rlock){-.....}, at: [<bf129288>] ep0_complete+0x18/0xdc [gadgetfs]
[ 40.502882]
[ 40.502882] but task is already holding lock:
[ 40.508967] (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[ 40.517811]
[ 40.517811] other info that might help us debug this:
[ 40.524623] Possible unsafe locking scenario:
[ 40.524623]
[ 40.530798] CPU0
[ 40.533346] ----
[ 40.535894] lock(&(&dev->lock)->rlock);
[ 40.540088] lock(&(&dev->lock)->rlock);
[ 40.544284]
[ 40.544284] *** DEADLOCK ***
[ 40.544284]
[ 40.550461] May be due to missing lock nesting notation
[ 40.550461]
[ 40.557544] 2 locks held by usb/733:
[ 40.561271] #0: (&f->f_pos_lock){+.+.+.}, at: [<c02a6114>] __fdget_pos+0x40/0x48
[ 40.569219] #1: (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[ 40.578523]
[ 40.578523] stack backtrace:
[ 40.583075] CPU: 0 PID: 733 Comm: usb Not tainted 4.6.0-08691-g7f3db9a #37
[ 40.590246] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 40.596625] [<c010ffbc>] (unwind_backtrace) from [<c010c1bc>] (show_stack+0x10/0x14)
[ 40.604718] [<c010c1bc>] (show_stack) from [<c04207fc>] (dump_stack+0xb0/0xe4)
[ 40.612267] [<c04207fc>] (dump_stack) from [<c01886ec>] (__lock_acquire+0xf68/0x1994)
[ 40.620440] [<c01886ec>] (__lock_acquire) from [<c0189528>] (lock_acquire+0xd8/0x238)
[ 40.628621] [<c0189528>] (lock_acquire) from [<c06ad6b4>] (_raw_spin_lock_irqsave+0x38/0x4c)
[ 40.637440] [<c06ad6b4>] (_raw_spin_lock_irqsave) from [<bf129288>] (ep0_complete+0x18/0xdc [gadgetfs])
[ 40.647339] [<bf129288>] (ep0_complete [gadgetfs]) from [<bf10a728>] (musb_g_giveback+0x118/0x1b0 [musb_hdrc])
[ 40.657842] [<bf10a728>] (musb_g_giveback [musb_hdrc]) from [<bf108768>] (musb_g_ep0_queue+0x16c/0x188 [musb_hdrc])
[ 40.668772] [<bf108768>] (musb_g_ep0_queue [musb_hdrc]) from [<bf12a944>] (ep0_read+0x544/0x5e0 [gadgetfs])
[ 40.678963] [<bf12a944>] (ep0_read [gadgetfs]) from [<c0284470>] (__vfs_read+0x20/0x110)
[ 40.687414] [<c0284470>] (__vfs_read) from [<c0285324>] (vfs_read+0x88/0x114)
[ 40.694864] [<c0285324>] (vfs_read) from [<c0286150>] (SyS_read+0x44/0x9c)
[ 40.702051] [<c0286150>] (SyS_read) from [<c0107820>] (ret_fast_syscall+0x0/0x1c)
This is caused by the spinlock bug in ep0_read().
Fix the two other deadlock sources in gadgetfs_setup() too.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 4879efb34f7d49235fac334d76d9c6a77a021413 ]
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fda4 ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit c1a3acaadde7eb260f4fd4ec87cb87d3ffeed979 ]
There's no need to keep one local variable for clock, and
then assign the same to 'clk' member of dwc3_exynos.
Just cleaning it up.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 028c49f5e02a257c94129cd815f7c8485f51d4ef ]
The interface read URB is submitted in attach, but was only unlinked by
the driver at disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we would end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callback.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # v3.5: 40d04738491d
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 9e45284984096314994777f27e1446dfbfd2f0d7 ]
The interface read and event URBs are submitted in attach, but were
never explicitly unlinked by the driver. Instead the URBs would have
been killed by usb-serial core on disconnect.
In case of a late probe error (e.g. due to failed minor allocation),
disconnect is never called and we could end up with active URBs for an
unbound interface. This in turn could lead to deallocated memory being
dereferenced in the completion callbacks.
Fixes: ee467a1f2066 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit 35be1a71d70775e7bd7e45fa6d2897342ff4c9d2 ]
The interface instat and indat URBs were submitted in attach, but never
unlinked in release before deallocating the corresponding transfer
buffers.
In the case of a late probe error (e.g. due to failed minor allocation),
disconnect would not have been called before release, causing the
buffers to be freed while the URBs are still in use. We'd also end up
with active URBs for an unbound interface.
Fixes: f9c99bb8b3a1 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit c8d62957d450cc1a22ce3242908709fe367ddc8e ]
URBs and buffers allocated in attach for Epic devices would never be
deallocated in case of a later probe error (e.g. failure to allocate
minor numbers) as disconnect is then never called.
Fix by moving deallocation to release and making sure that the
URBs are first unlinked.
Fixes: f9c99bb8b3a1 ("USB: usb-serial: replace shutdown with disconnect,
release")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit c5c0c55598cefc826d6cfb0a417eeaee3631715c ]
Private data, URBs and buffers allocated for Epic devices during
attach were never released on errors (e.g. missing endpoints).
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # v2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
|
[ Upstream commit a377f9e906af4df9071ba8ddba60188cb4013d93 ]
A bug in the CRTSCTS handling caused RTS to alternate between
CRTSCTS=0 => "RTS is transmit active signal" and
CRTSCTS=1 => "RTS is used for receive flow control"
instead of
CRTSCTS=0 => "RTS is statically active" and
CRTSCTS=1 => "RTS is used for receive flow control"
This only happened after first having enabled CRTSCTS.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
[johan: reword commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
|
