| Age | Commit message (Collapse) | Author |
|---|
|
Some PHYs may need to enter related mode, and do some settings.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Patch split function cdns3_drd_switch_gadget and
cdns3_drd_switch_host into:
- cdns3_drd_host_on
- cdns3_drd_host_off
- cdns3_drd_gadget_on
- cdns3_drd_gadgett_off
These functions don't have any shared code so it's better to
have smaller, faster and easier functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Patch adds 2 definitions that make it easier to understand the code.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Patch changes return type from int to bool for
cdns3_is_host and cdns3_is_device functions.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
IRQ_NONE can be returned indirect.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Patch deletes unnecessary != from condition statement in cdns3_drd_init
function.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Patch remove some variables initialization from core.c and drd.c
file.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduce new Cadence USBSS DRD driver to Linux kernel.
The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
