| Age | Commit message (Collapse) | Author |
|---|
|
MCSPI controller have few limitations regarding the transaction
size when the FIFO buffer is enabled and the WCNT feature is used
to find the end of word, in this case if WCNT is not a multiple of
the FIFO Almost Empty Level (AEL), then the FIFO empty event is not
generated correctly. In addition to this limitation, few other unknown
sequence of events that causes the FIFO empty status to not reflect the
exact status were found when FIFO is being used without DMA enabled
during extended testing in AM65x platform. Till the exact root cause
is found and fixed, revert the FIFO support without DMA.
See J721E Technical Reference Manual (SPRUI1C), section 12.1.5
for further details: http://www.ti.com/lit/pdf/spruil1
This reverts commit 75223bbea840e ("spi: omap2-mcspi: Add FIFO support
without DMA")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://msgid.link/r/20240212120049.438495-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, the built-in 64-byte FIFO on the MCSPI controller is not
enabled in PIO mode and is used only when DMA is enabled. Enable the
FIFO in PIO mode by default for transactions larger than the FIFO depth
and fallback only if FIFO is not available. When DMA is not enabled,
it is efficient to enable the RX FIFO almost full and TX FIFO almost
empty events after each FIFO fill instead of each word.
Update omap2_mcspi_set_fifo() to enable the events accordingly and
also rely on OMAP2_MCSPI_CHSTAT_RXS for the last transfer instead of the
FIFO events to handle the case when the transfer size is not a multiple
of FIFO depth.
See J721E Technical Reference Manual (SPRUI1C), section 12.1.5
for further details: http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20231013092629.19005-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A hardcoded reference clock of 48 MHz is used to calculate the
clock divisor values, but the reference clock frequency can be
different across devices and can be configured which can cause
a mismatch between the reported frequency and actual SPI clock
frequency observed. Fix this by fetching the clock rate from
the clock provider and falling back to hardcoded reference only
if the clock is not supplied.
Fixes: 2cd7d393f461 ("arm64: dts: ti: k3-am654: Add McSPI DT nodes")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926113812.30692-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change legacy name master/slave to modern name host/target or controller.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230823033003.3407403-22-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When platform_get_irq() is called, the error message has been printed,
so it need not to call dev_err_probe() to print error, we remove the
redundant platform_get_irq().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230801135442.255604-1-wangzhu9@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230327055346.76625-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch is in the continuation to the discussions which happened on
'commit f89504300e94 ("spi: Stacked/parallel memories bindings")' for
adding dt-binding support for stacked/parallel memories.
This patch series updated the spi-nor, spi core and the spi drivers
to add stacked and parallel memories support.
The first patch
https://lore.kernel.org/all/20230119185342.2093323-1-amit.kumar-mahapatra@amd.com/
of the previous series got applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
But the rest of the patches in the series did not get applied due to merge
conflict, so send the remaining patches in the series after rebasing it
on top of for-next branch.
---
BRANCH: for-next
Changes in v6:
- Rebased on top of latest v6.3-rc1 and fixed merge conflicts in
spi-mpc512x-psc.c, sfdp.c, spansion.c files and removed spi-omap-100k.c.
- Updated spi_dev_check( ) to reject new devices if any one of the
chipselect is used by another device.
Changes in v5:
- Rebased the patches on top of v6.3-rc1 and fixed the merge conflicts.
- Fixed compilation warnings in spi-sh-msiof.c with shmobile_defconfig
Changes in v4:
- Fixed build error in spi-pl022.c file - reported by Mark.
- Fixed build error in spi-sn-f-ospi.c file.
- Added Reviewed-by: Serge Semin <fancer.lancer@gmail.com> tag.
- Added two more patches to replace spi->chip_select with API calls in
mpc832x_rdb.c & cs35l41_hda_spi.c files.
Changes in v3:
- Rebased the patches on top of
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
- Added a patch to convert spi_nor_otp_region_len(nor) &
spi_nor_otp_n_regions(nor) macros into inline functions
- Added Reviewed-by & Acked-by tags
Changes in v2:
- Rebased the patches on top of v6.2-rc1
- Created separate patch to add get & set APIs for spi->chip_select &
spi->cs_gpiod, and replaced all spi->chip_select and spi->cs_gpiod
references with the API calls.
- Created separate patch to add get & set APIs for nor->params.
---
Amit Kumar Mahapatra (15):
spi: Replace all spi->chip_select and spi->cs_gpiod references with
function call
net: Replace all spi->chip_select and spi->cs_gpiod references with
function call
iio: imu: Replace all spi->chip_select and spi->cs_gpiod references
with function call
mtd: devices: Replace all spi->chip_select and spi->cs_gpiod
references with function call
staging: Replace all spi->chip_select and spi->cs_gpiod references
with function call
platform/x86: serial-multi-instantiate: Replace all spi->chip_select
and spi->cs_gpiod references with function call
powerpc/83xx/mpc832x_rdb: Replace all spi->chip_select references with
function call
ALSA: hda: cs35l41: Replace all spi->chip_select references with
function call
spi: Add stacked and parallel memories support in SPI core
mtd: spi-nor: Convert macros with inline functions
mtd: spi-nor: Add APIs to set/get nor->params
mtd: spi-nor: Add stacked memories support in spi-nor
spi: spi-zynqmp-gqspi: Add stacked memories support in GQSPI driver
mtd: spi-nor: Add parallel memories support in spi-nor
spi: spi-zynqmp-gqspi: Add parallel memories support in GQSPI driver
arch/powerpc/platforms/83xx/mpc832x_rdb.c | 2 +-
drivers/iio/imu/adis16400.c | 2 +-
drivers/mtd/devices/mtd_dataflash.c | 2 +-
drivers/mtd/spi-nor/atmel.c | 17 +-
drivers/mtd/spi-nor/core.c | 665 +++++++++++++++---
drivers/mtd/spi-nor/core.h | 8 +
drivers/mtd/spi-nor/debugfs.c | 4 +-
drivers/mtd/spi-nor/gigadevice.c | 4 +-
drivers/mtd/spi-nor/issi.c | 11 +-
drivers/mtd/spi-nor/macronix.c | 6 +-
drivers/mtd/spi-nor/micron-st.c | 39 +-
drivers/mtd/spi-nor/otp.c | 48 +-
drivers/mtd/spi-nor/sfdp.c | 29 +-
drivers/mtd/spi-nor/spansion.c | 50 +-
drivers/mtd/spi-nor/sst.c | 7 +-
drivers/mtd/spi-nor/swp.c | 22 +-
drivers/mtd/spi-nor/winbond.c | 10 +-
drivers/mtd/spi-nor/xilinx.c | 18 +-
drivers/net/ethernet/adi/adin1110.c | 2 +-
drivers/net/ethernet/asix/ax88796c_main.c | 2 +-
drivers/net/ethernet/davicom/dm9051.c | 2 +-
drivers/net/ethernet/qualcomm/qca_debug.c | 2 +-
drivers/net/ieee802154/ca8210.c | 2 +-
drivers/net/wan/slic_ds26522.c | 2 +-
.../net/wireless/marvell/libertas/if_spi.c | 2 +-
drivers/net/wireless/silabs/wfx/bus_spi.c | 2 +-
drivers/net/wireless/st/cw1200/cw1200_spi.c | 2 +-
.../platform/x86/serial-multi-instantiate.c | 3 +-
drivers/spi/spi-altera-core.c | 2 +-
drivers/spi/spi-amd.c | 4 +-
drivers/spi/spi-ar934x.c | 2 +-
drivers/spi/spi-armada-3700.c | 4 +-
drivers/spi/spi-aspeed-smc.c | 13 +-
drivers/spi/spi-at91-usart.c | 2 +-
drivers/spi/spi-ath79.c | 4 +-
drivers/spi/spi-atmel.c | 26 +-
drivers/spi/spi-au1550.c | 4 +-
drivers/spi/spi-axi-spi-engine.c | 2 +-
drivers/spi/spi-bcm-qspi.c | 10 +-
drivers/spi/spi-bcm2835.c | 19 +-
drivers/spi/spi-bcm2835aux.c | 4 +-
drivers/spi/spi-bcm63xx-hsspi.c | 30 +-
drivers/spi/spi-bcm63xx.c | 2 +-
drivers/spi/spi-bcmbca-hsspi.c | 30 +-
drivers/spi/spi-cadence-quadspi.c | 5 +-
drivers/spi/spi-cadence-xspi.c | 4 +-
drivers/spi/spi-cadence.c | 4 +-
drivers/spi/spi-cavium.c | 8 +-
drivers/spi/spi-coldfire-qspi.c | 8 +-
drivers/spi/spi-davinci.c | 18 +-
drivers/spi/spi-dln2.c | 6 +-
drivers/spi/spi-dw-core.c | 2 +-
drivers/spi/spi-dw-mmio.c | 4 +-
drivers/spi/spi-falcon.c | 2 +-
drivers/spi/spi-fsi.c | 2 +-
drivers/spi/spi-fsl-dspi.c | 16 +-
drivers/spi/spi-fsl-espi.c | 6 +-
drivers/spi/spi-fsl-lpspi.c | 2 +-
drivers/spi/spi-fsl-qspi.c | 6 +-
drivers/spi/spi-fsl-spi.c | 2 +-
drivers/spi/spi-geni-qcom.c | 6 +-
drivers/spi/spi-gpio.c | 4 +-
drivers/spi/spi-gxp.c | 4 +-
drivers/spi/spi-hisi-sfc-v3xx.c | 2 +-
drivers/spi/spi-img-spfi.c | 14 +-
drivers/spi/spi-imx.c | 30 +-
drivers/spi/spi-ingenic.c | 4 +-
drivers/spi/spi-intel.c | 2 +-
drivers/spi/spi-jcore.c | 4 +-
drivers/spi/spi-lantiq-ssc.c | 6 +-
drivers/spi/spi-mem.c | 4 +-
drivers/spi/spi-meson-spicc.c | 2 +-
drivers/spi/spi-microchip-core.c | 6 +-
drivers/spi/spi-mpc512x-psc.c | 8 +-
drivers/spi/spi-mpc52xx.c | 2 +-
drivers/spi/spi-mt65xx.c | 6 +-
drivers/spi/spi-mt7621.c | 2 +-
drivers/spi/spi-mux.c | 8 +-
drivers/spi/spi-mxic.c | 10 +-
drivers/spi/spi-mxs.c | 2 +-
drivers/spi/spi-npcm-fiu.c | 20 +-
drivers/spi/spi-nxp-fspi.c | 10 +-
drivers/spi/spi-omap-uwire.c | 8 +-
drivers/spi/spi-omap2-mcspi.c | 24 +-
drivers/spi/spi-orion.c | 4 +-
drivers/spi/spi-pci1xxxx.c | 4 +-
drivers/spi/spi-pic32-sqi.c | 2 +-
drivers/spi/spi-pic32.c | 4 +-
drivers/spi/spi-pl022.c | 4 +-
drivers/spi/spi-pxa2xx.c | 6 +-
drivers/spi/spi-qcom-qspi.c | 2 +-
drivers/spi/spi-rb4xx.c | 2 +-
drivers/spi/spi-rockchip-sfc.c | 2 +-
drivers/spi/spi-rockchip.c | 26 +-
drivers/spi/spi-rspi.c | 10 +-
drivers/spi/spi-s3c64xx.c | 2 +-
drivers/spi/spi-sc18is602.c | 4 +-
drivers/spi/spi-sh-msiof.c | 6 +-
drivers/spi/spi-sh-sci.c | 2 +-
drivers/spi/spi-sifive.c | 6 +-
drivers/spi/spi-sn-f-ospi.c | 2 +-
drivers/spi/spi-st-ssc4.c | 2 +-
drivers/spi/spi-stm32-qspi.c | 12 +-
drivers/spi/spi-sun4i.c | 2 +-
drivers/spi/spi-sun6i.c | 2 +-
drivers/spi/spi-synquacer.c | 6 +-
drivers/spi/spi-tegra114.c | 28 +-
drivers/spi/spi-tegra20-sflash.c | 2 +-
drivers/spi/spi-tegra20-slink.c | 6 +-
drivers/spi/spi-tegra210-quad.c | 8 +-
drivers/spi/spi-ti-qspi.c | 16 +-
drivers/spi/spi-topcliff-pch.c | 4 +-
drivers/spi/spi-wpcm-fiu.c | 12 +-
drivers/spi/spi-xcomm.c | 2 +-
drivers/spi/spi-xilinx.c | 6 +-
drivers/spi/spi-xlp.c | 4 +-
drivers/spi/spi-zynq-qspi.c | 2 +-
drivers/spi/spi-zynqmp-gqspi.c | 58 +-
drivers/spi/spi.c | 225 ++++--
drivers/spi/spidev.c | 6 +-
drivers/staging/fbtft/fbtft-core.c | 2 +-
drivers/staging/greybus/spilib.c | 2 +-
include/linux/mtd/spi-nor.h | 18 +-
include/linux/spi/spi.h | 34 +-
include/trace/events/spi.h | 10 +-
sound/pci/hda/cs35l41_hda_spi.c | 2 +-
126 files changed, 1350 insertions(+), 615 deletions(-)
--
2.25.1
|
|
call
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de> # Rockchip drivers
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org> # Aspeed driver
Reviewed-by: Dhruva Gole <d-gole@ti.com> # SPI Cadence QSPI
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> # spi-stm32-qspi
Acked-by: William Zhang <william.zhang@broadcom.com> # bcm63xx-hsspi driver
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> # DW SSI part
Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144736.1547110-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-51-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This condition was accidentally changed from "if (status < 0)" to
"if (status)". The platform_get_irq() function returns non-zero
positive values on success so, unfortunately, the driver could not be
used. Change the condition back to how it was.
Fixes: f4ca8c88c2c7 ("spi: omap2-mcspi: Switch to use dev_err_probe() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/Yyq8Q/kd301wVzg8@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122504.1896302-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The module omap2-mcspi does not support the interword delay
parameter present in the spi transfer. On one side, if the module
is instructed to use the dma, this parameter is correctly ignored.
However, without the usage of the dma, that parameter should be
used.
The patch introduce the handling of such delay in the omap2-mcspi
module, using standard spi_delay struct. The patch has been tested
using as benchmark a DM3730.
The delay function used (spi_delay_exec) is already present in the
kernel and it checks on its own the validity of the input, as such,
no additional checks are present.
The range of usage of the udelay function is incremented to 200 us,
as the change from udelay to usleep_range introduces not
neglectible delays.
Signed-off-by: Andrea Zanotti <andreazanottifo@gmail.com>
Link: https://lore.kernel.org/r/20220502111300.24754-1-andreazanottifo@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085433.2541670-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.14
|
|
Commit c7299fea6769 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea6769, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea6769 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
<songzhiqi1@huawei.com>:
This patchset fixes missing parentheses of sizeof reported by checkpatch.pl
under drivers/spi/.
Zhiqi Song (7):
spi: lm70llp: add parenthesis for sizeof
spi: mpc512x-psc: add parenthesis for sizeof
spi: mpc52xx: add parenthesis for sizeof
spi: mpc52xx-psc: add parenthesis for sizeof
spi: omap2-mcspi: add parenthesis for sizeof
spi: omap-uwire: add parenthesis for sizeof
spi: ppc4xx: add parenthesis for sizeof
drivers/spi/spi-lm70llp.c | 2 +-
drivers/spi/spi-mpc512x-psc.c | 4 ++--
drivers/spi/spi-mpc52xx-psc.c | 4 ++--
drivers/spi/spi-mpc52xx.c | 2 +-
drivers/spi/spi-omap-uwire.c | 2 +-
drivers/spi/spi-omap2-mcspi.c | 2 +-
drivers/spi/spi-ppc4xx.c | 4 ++--
7 files changed, 10 insertions(+), 10 deletions(-)
--
2.7.4
|
|
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-6-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
One of the author names got an invalid char, probably due to
a bad charset conversion, being replaced by the
REPLACEMENT CHARACTER U+fffd ('�').
Use the author's e-mail has the characters without accents,
as also used at the .mailmap file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ff8d296e1fdcc4f1c6df94434a5720bcedcd0ecf.1621412009.git.mchehab+huawei@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the (optional) idle pinctrl state during runtime suspend. This is the
same schema used in PL022 driver and can help with HW designs sharing
the SPI lines for different purposes.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20210222023243.491432-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 13d515c796 (spi: omap2-mcspi: Switch to
readl_poll_timeout()).
The amount of time spent polling for the MCSPI_CHSTAT bits to be set on
AM335x-icev2 platform is less than 1us (about 0.6us) in most cases, with
or without using DMA. So, in most cases the function need not sleep.
Also, setting the sleep_usecs to zero would not be optimal here because
ktime_add_us() used in readl_poll_timeout() is slower compared to the
direct addition used after the revert. So, it is sub-optimal to use
readl_poll_timeout in this case.
When DMA is not enabled, this revert results in an increase of about 27%
in throughput and decrease of about 20% in CPU usage. However, the CPU
usage and throughput are almost the same when used with DMA.
Therefore, fix this by reverting the commit which switched to using
readl_poll_timeout().
Fixes: 13d515c796ad ("spi: omap2-mcspi: Switch to readl_poll_timeout()")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20200910122624.8769-1-a-govindraju@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OMAP2 MCSPI has some kind of half-baked GPIO CS support:
it includes code like this:
if (gpio_is_valid(spi->cs_gpio)) {
ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
(...)
But it doesn't parse the "cs-gpios" attribute in the device
tree to count the number of GPIOs or pick out the GPIO numbers
and put these in the SPI master's .cs_gpios property.
We complete the implementation of supporting CS GPIOs
from the device tree and switch it over to use the SPI core
for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200625231257.280615-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On AM654, McSPI can only support 4K - 1 bytes per transfer when DMA is
enabled. Therefore populate master->max_transfer_size callback to
inform client drivers of this restriction when DMA channels are
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length")
broke SPI transfers where bits_per_word != 8. This is because of
mimsatch between McSPI FIFO level event trigger size (SPI word length) and
DMA request size(word length * maxburst). This leads to data
corruption, lockup and errors like:
spi1.0: EOW timed out
Fix this by setting DMA maxburst size to 1 so that
McSPI FIFO level event trigger size matches DMA request size.
Fixes: b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length")
Cc: stable@vger.kernel.org
Reported-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
I've been wondering still about omap2-mcspi related suspend and resume
flakeyness and looks like we're missing calls to spi_master_suspend()
and spi_master_resume(). Adding those and using pm_runtime_force_suspend()
and pm_runtime_force_resume() makes things work for suspend and resume
and allows us to stop using noirq suspend and resume.
And while at it, let's use SET_SYSTEM_SLEEP_PM_OPS to simplify things
further.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support to use McSPI controller as SPI slave. In slave mode, DMA TX
completion does not mean entire data has been shifted out as data might
still be stuck in FIFO waiting for master to clock the bus. Therefore,
add an IRQ handler for slave mode to know when entire data in FIFO has
been shifted out.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McSPI has 32 byte FIFO in Transmit-Receive mode. Current code tries to
configuration FIFO watermark level for DMA trigger to be GCD of transfer
length and max FIFO size which would mean trigger level may be set to 32
for transmit-receive mode if length is aligned. This does not work in
case of SPI slave mode where FIFO always needs to have data ready
whenever master starts the clock. With DMA trigger size of 32 there will
be a small window during slave TX where DMA is still putting data into
FIFO but master would have started clock for next byte, resulting in
shifting out of stale data. Similarly, on Slave RX side there may be RX
FIFO overflow
Fix this by setting FIFO watermark for DMA trigger to word
length. This means DMA is triggered as soon as FIFO has space for word
length bytes and DMA would make sure FIFO is almost always full
therefore improving FIFO occupancy in both master and slave mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use standard readl_poll_timeout() macro for polling on status bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 5a686b2c9ed4 ("spi: omap2-mcspi: Idle hardware during suspend
and resume") added calls for pm_runtime_force_suspend() and
pm_runtime_force_resume() to make sure spi is idled between
device_prepare() and device_complete().
But testing Linux next, I now noticed that we will get the following:
spi_master spi0: Failed to power device: -13
Looking at things more turns out we can just remove this non-standard
code. I was probably testing with some extra experimental patches
earlier when I thought we need pm_runtime_force_suspend() and
pm_runtime_force_resume().
Fixes: 5a686b2c9ed4 ("spi: omap2-mcspi: Idle hardware during suspend
and resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We currently are calling mcspi suspend and resume without considering
that mcspi might provide resources for other device driver such as
regulators. This means resume can fail and will produce -EACCES if
errors if anything calls mcspi functions between device_prepare()
and device_complete().
To fix the issue, let's do the following changes:
1. Let's add checking for return values for pm_runtime_get calls,
and call pm_runtime_put_noidle() on errors. Things still fail
after this change, but at least we see something is wrong as
we now see -EACCES errors on resume.
2. Let's use noirq level for suspend and resume as other drivers
can still call SPI related functions on suspend and resume. This
still won't fix the -EACCES issue, but gets us to something a bit
saner.
3. Finally, let's modify suspend and resume to call to make sure
the device is idled properly on suspend. We have device_prepare()
call pm_runtime_get_noresume() that won't get released until in
device_complete() when it calls pm_runtime_put(). So if SPI is
still active on entering suspend, it will never get idled unless
we add calls to pm_runtime_force_suspend() and resume. This also
fixes the -EACCES errors on resume together with changes 1 and 2
above.
And since we're already rewriting suspend resume functions, let's
arrange the order of suspend and resume functions to be like they
usually are with suspend first.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can have the SoC enter off mode also during idle, not just
during suspend. Currently we are handling the CS restore properly
for unused CS only for resume and not for runtime resume.
Let's just move all the context related restore to runtime_resume().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi framework should allocate bus number dynamically either
via Linux IDR or spi alias for master drivers. This patch deletes
code pertaining to manual allocation of spi bus number in spi omap2
master driver.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Tested-by: Karthik Tummala <karthik@techveda.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The check to see if status is less than zero is actually redundant
as all previous places where it is -ve have already branched to the
exit paths, so it is never less than zero at the check.
Detected by CoverityScan, CID#1357119 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When running the spi-loopback-test with slower clock rate like 10 KHz,
the test for 251 bytes transfer was failed. This failure triggered an
spi-omap2-mcspi's error message "DMA RX last word empty".
This message means that PIO for reading the remaining bytes due to the
DMA transfer length reduction is failed. This problem can be fixed by
polling OMAP2_MCSPI_CHSTAT_RXS bit in channel status register to wait
until the receive buffer register is filled.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
currently during probe the resource data gets modified and device
physical address remains valid only during first load. If the module is
unloaded and loaded again, the ioremp will be done on a incorrect address
as the resource was modified during previous module load.
This patch fixes this issue.
Signed-off-by: Vikram N <vicky773@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, the driver handles mapping buffers to be used by the DMA.
However, there are times that the current mapping implementation will
fail for certain buffers. Fortunately, the SPI framework can detect
and map buffers so its usable by the DMA.
Update the driver to utilize the SPI framework for buffer
mapping instead. Also incorporate hooks that the framework uses to
determine if the DMA can or can not be used.
This will result in the original omap2_mcspi_transfer_one function being
deleted and omap2_mcspi_work_one being renamed to
omap2_mcspi_transfer_one. Previously transfer_one was only responsible
for mapping and work_one handled the transfer. But now only transferring
needs to be handled by the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
OMAP35x and OMAP37x mentions in the McSPI End-of-Transfer Sequences section
that if the McSPI is configured as a Master and only DMA RX is being
performed then the DMA transfer size needs to be reduced by 1 or 2.
This was originally implemented by:
commit 57c5c28dbc83 ("spi: omap2_mcspi rxdma bugfix")
This patch adds comments to clarify what is going on in the code since its
not obvious what problem its addressing.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Cc: linux-spi@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.
Reported-by: Joseph Bell <joe@iachieved.it>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in DT, these calls turn
to NOPs.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the "Switch driver to use transfer_one" change, the cs_change
behavior has changed and a channel chip select can still be
asserted when changing channel from a previous last transfer in a
message having the cs_change attribute.
Since there is no sense having multiple chip select being asserted at the
same time, disable all the remaining forced chip selects in a the
prepare_message called right before a spi_transfer_one_message call.
It ignores the current channel configuration in order to keep the
possibility to leave the chip select asserted between messages.
It fixes this bug on a DM8168 SoC ES2.1 Soc and an OMAP4 ES2.1 SoC.
It was hanging all the other channels transfers when a CHCONF_FORCE
is present on the wrong channel.
Fixes: b28cb9414db9 ("spi: omap2-mcspi: Switch driver to use transfer_one")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit ddcad7e9068eb omap2_mcspi_set_cs() is called without
runtime power management requested. This patch fixes the problem by
requesting runtime power management in omap2_mcspi_set_cs().
Reported-By: Pali Rohár <pali.rohar@gmail.com>
Fixes: ddcad7e9068eb (spi: omap2-mcspi: Fix native cs with new set_cs)
Tested-By: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If a valid GPIO is specified but cannot be requested by the driver, print a
message and error out of omap2_mcspi_setup.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OMAP2_MCSPI_CHCONF_FORCE must be toggled even when using GPIO
chip selects. This patch conditionally calls the omap2_mcspi_set_cs
function to do so when using GPIO chip selects.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
