| Age | Commit message (Collapse) | Author |
|---|
|
commit af61e27c3f77c7623b5335590ae24b6a5c323e22 upstream.
On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which
in turn calls pci_disable_device if the device is enabled prior to
suspending. However, _scsih_suspend also calls pci_disable_device
itself.
Thus, in the event that the device is enabled prior to suspending,
pci_disable_device will be called twice. This patch removes the
duplicate call to pci_disable_device in _scsi_suspend as it is both
unnecessary and results in a kernel oops.
Signed-off-by: Tyler Stachecki <tstache1@binghamton.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0df96a0068daee4f9c2189c29b9053eb6e46b17 upstream.
Missing delay is not getting set properly. The reason is that it is not
defined in the same file from where it is being invoked. The fix is to move
the missing delay module parameter from mpt2sas_base.c to mpt2sas_scsh.c.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48ba2efc382f94fae16ca8ca011e5961a81ad1ea upstream.
When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
|
|
capabilities
Add a parameter that allows the host protection capabilities mask to be
provided at module load time.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Only a target device should return ABORTED COMMAND when a PI error is
discovered. The HBA should always set the sense key to ILLEGAL REQUEST.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
removed and then again gets added with new target ids
When device discovery is disabled during driver load time using module
parameter "disable_discovery=1" and when diag reset is issued then from logs,
it is observed that the devices get added, removed and then added with new
target ids.
So, in order to limit this turn-off the code which is deleting and devices
across host reset when the disable_discovery module parameter is turned on.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
working
This patch provides a command line option to disable "Port enable" during
the driver load.
The objective of this command line option is to load the driver and do
all the necessary initialization excluding port enable(i.e. delay
device discovery)
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
range
When specifying the command line option "max_sectors" less than 64, then
warning message should provide correct upper boundary value 32767 instead of
8192.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Copyright String in all the drivers sources were changed to 2012
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When scsi_add_host fails the scsi_host_put should be called.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
simultaneously another hard drive is hot unplugged
Following the host reset, the firmware discovery is reassigning another hard
drive in the topology to the same device handle as that device is getting hot
removed. Until the driver device removal routine is called, there will be two
hard drive with the matching device handle in the internal device link
list. In the device removal routine, a separate function which moves the
device from BLOCKED into OFFLINE state. Since this routine is passed with the
device handle passed as input parameter, the routine will be traversing the
internal device link list searching for matching device handle. This results
in two devices with matching device handle, therefore both devices goes
OFFLINE.
To fix this issue,the input parameter is changed from device handle to SAS
address, therefore only the device that is hot unplugged will be placed in
OFFLINE state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix several endian issues found by runing sparse.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Modified the source code as per the findings reported by the source
code analysis tool. Source code for the following functionalities
has been touched. None of the driver functionalities has changed.
- SMP Passthrough IOCTL
- Debug messages for MPT Replies (i.e. bit 9 of Logging Level)
- Task Management using sysfs
- Device removal, i.e. when a target device (including any PD within a volume)
is removed, and Volume Deletion.
- Trace Buffer
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
raid_device, and expander_device lists
There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.
Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list. Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter. This is a bitmask used
to identify which devices need blocking when there is device loss. This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
_scsih_probe
Removed redundant calling of _scsih_probe_devices() from _scsih_probe as
it is getting called from _scsih_scan_finished.
Also moved the function scsi_scan_host(shost) to get called after the
volumes on warp drive are reported to the OS. Otherwise by the time
the (ioc->hide_drives) flags is set, the volumes on warp drive
are reported to the OS already.
Also modified the initialization of reply queues only in case of driver load
time in the function _base_make_ioc_operational().
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The amount of memory required for tracking chain buffers is rather
large, and when the host credit count is big, memory allocation
failure occurs inside __get_free_pages.
The fix is to limit the number of chains to 100,000. In addition,
the number of host credits is limited to 30,000 IOs. However this
limitation can be overridden this using the command line option
max_queue_depth. The algorithm for calculating the
reply_post_queue_depth is changed so that it is equal to
(reply_free_queue_depth + 16), previously it was (reply_free_queue_depth * 2).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When an I/O request to a WarpDrive is timed out by SML and if the
I/O request to the WarpDrive is sent as direct I/O then the aborted
direct I/O will be retried as normal Volume I/O and which results
in failure of Target Reset and results in host reset.
The fix is to not retry a failed IO to volume when the original
IO was sent as direct IO with an ioc status
MPI2_IOCSTATUS_SCSI_TASK_TERMINATED.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added code to release the spinlock that is used to protect the
raid device list before calling a function that can block. The
blocking was causing a reschedule, and subsequently it is tried
to acquire the same lock, resulting in a panic (NMI Watchdog
detecting a CPU lockup).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Increase max transfer support from 4MB to 16MB.
This is done by changing the shost->max_sector from 8192 to 32767
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The driver is modified to allow access to the greater than 2TB WarpDrive
and properly handle direct-io mapping for WarpDrive volumes greater than 2TB.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
slave_destroy callback when all the LUNS have been deleted
If the sas_device->starget to NULL from slave_destroy callback for LUN=1
even though LUN=0 exist, results in entire target getting deleted.
To resolve the issue, the driver should only set sas_device->starget to
NULL when all the LUNS have been deleted from the slave_destroy.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
to avoid infinite resets
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Detection of Dead IOC has been done in fault_reset_work thread.
If IOC Doorbell is 0xFFFFFFFF, it will be detected as non-operation/DEAD IOC.
When a DEAD IOC is detected, the code is modified to remove that IOC and
all its attached devices from OS.
The PCI layer API pci_remove_bus_device() is called to remove the dead IOC.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
context
_scsih_smart_predicted_fault is called in an interrupt and therefore
must allocate memory using GFP_ATOMIC.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There was supposed to be a kzalloc() here and the compiler complained
about it.
mpt2sas_scsih.c: In function ‘mpt2sas_scsih_reset_handler’:
mpt2sas_scsih.c:2807:21: warning: ‘fw_event’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The driver was setting the action to MPI2_CONFIG_ACTION_PAGE_READ_CURRENT,
which only returns active volumes. In order to get info on inactive volumes,
the driver needs to change the action to
MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM, and traverse each config till the
iocstatus is MPI2_IOCSTATUS_CONFIG_INVALID_PAGE returned.
Added a change in the driver to remove the instance of
sas_device object when the driver returns "1" from the slave_configure callback.
Also fixed code to report the hot spares to the operating system with a /dev/sg
assigned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
complete while issued during creating a volume
This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
reset context
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sas_device_lock
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning]
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
removed while host reset is active
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The fix is to inhibit the warning message in _scsih_get_sas_address
when the MPI2_IOCSTATUS_CONFIG_INVALID_PAGE ioc status is returned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
[SCSI] qla4xxx: export address/port of connection (fix udev disk names)
[SCSI] ipr: Fix BUG on adapter dump timeout
[SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
[SCSI] hpsa: change confusing message to be more clear
[SCSI] iscsi class: fix vlan configuration
[SCSI] qla4xxx: fix data alignment and use nl helpers
[SCSI] iscsi class: fix link local mispelling
[SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
[SCSI] aacraid: use lower snprintf() limit
[SCSI] lpfc 8.3.27: Change driver version to 8.3.27
[SCSI] lpfc 8.3.27: T10 additions for SLI4
[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
[SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
[SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
[SCSI] megaraid_sas: Changelog and version update
[SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
[SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
[SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
[SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
...
|
|
support of the HBA
Support added for controllers capable of multi reply queues.
The following are the modifications to the driver to support NUMA.
1) Create the new structure adapter_reply_queue to contain the reply queue
info for every msix vector. This object will contain a
reply_post_host_index, reply_post_free for each instance, msix_index, among
other parameters. We will track all the reply queues on a link list called
ioc->reply_queue_list. Each reply queue is aligned with each IRQ, and is
passed to the interrupt via the bus_id parameter.
(2) The driver will figure out the msix_vector_count from the PCIe MSIX
capabilities register instead of the IOC Facts->MaxMSIxVectors. This is
because the firmware is not filling in this field until the driver has
already registered MSIX support.
(3) If the ioc_facts reports that the controller is MSIX compatible in the
capabilities, then the driver will request for multiple irqs. This count
is calculated based on the minimum between the online cpus available and
the ioc->msix_vector_count. This count is reported to firmware in the
ioc_init request.
(4) New routines were added _base_free_irq and _base_request_irq, so
registering and freeing msix vectors were done thru simple function API.
(5) The new routine _base_assign_reply_queues was added to align the msix
indexes across cpus. This will initialize the array called
ioc->cpu_msix_table. This array is looked up on every MPI request so the
MSIxIndex is set appropriately.
(6) A new shost sysfs attribute was added to report the reply_queue_count.
(7) User needs to set the affinity cpu mask, so the interrupts occur on the
same cpu that sent the original request.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
|
|
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
entry in MPI message
Issue:
This issue is seen on LSI H/W WarpDrive SSS6200 When filed direct I/O
is tried as volume I/O the scmd field in internal lookup table get
cleared and because of that the retried volume I/O never gets reported
as completed to SML.
Result:
I/O timeout and Error handling thread will kicking off
Fix:
Setting back the scmd in the lookup table before retrying the failed
direct i/o
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
shutdown call
Driver should not call shutdown call from _scsih_remove otherwise,
The scsi midlayer can be deadlocked when devices are removed from the driver
pci_driver->shutdown handler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Properly handling of target reset in multi-initiator environment
Clean up in broadcast change handling:
(1) Need to look at the status of each task management request, and retry
the TM when there are failures.
(2) Need quiescence IO so the driver doesn't take on more IO request while
it's in the middle of sending TM request to firmware
(3) Add support to keep track of how many pending broadcast AEN events
are received while the broadcast handling is active, then loop back at
the end of this routine if there were any events received.
Clean up in mpt2sas_scsih_issue_tm routine:
(1) Make sure proper status is returned when host reset fails
(2) Clean up sanity checks near end of routine, insuring all outstanding
IOs were completed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This feature is to override the default
max_sectors setting at load time, taking max_sectors as an
command line option when loading the driver. The setting is
currently hard-coded in the driver to 8192 sectors (4MB transfers).
If max_sectors is specified at load time, minimum specified
setting will be 64, and the maximum is 8192. The driver will
modify the setting to be on even boundary. If max_sectors is not
specified, the driver will default to 8192.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch addresses many endian issues solved by runing sparse with the
option __CHECK_ENDIAN__ turned on.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Ensure that the initial reference tag is passed on to the HBA firmware
for DIF Type 2 devices.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
context
Driver was a sending a SEP request during interrupt context which
required to go to sleep.
The fix is to rearrange the code so a fake event
MPT2SAS_TURN_ON_FAULT_LED is fired from interrupt context, then later
during the kernel worker threads processing, the SEP request is issued
to firmware.
Cc: stable@kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
