| Age | Commit message (Collapse) | Author |
|---|
|
commit c2e771b02792d222cbcd9617fe71482a64f52647 upstream.
Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.
Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.
The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 9f33a2ae59f24452c1076749deb615bccd435ca9 upstream.
The NFP6000 has an erratum where reading/writing to PCI config space
addresses above 0x600 can cause the NFP to generate PCIe completion
timeouts.
Limit the NFP6000's config space size to 0x600 bytes.
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit c20aecf6963d1273d8f6d61c042b4845441ca592 upstream.
If a device quirk modifies the pci_dev->cfg_size to be less than
PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256),
the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE.
Allow sysfs access to config space up to cfg_size, even if the device
doesn't support the entire 4096-byte PCIe config space.
Note that pci_read_config() and pci_write_config() limit access to
dev->cfg_size even though pcie_config_attr contains 4096 (the maximum
size).
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
[bhelgaas: more changelog edits]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b07461a8e45b7a62ef7fb46e4f6ada66f63406a8 upstream.
AER errors might be recorded when powering-on devices. These errors can be
ignored, so firmware usually clears them before the OS enumerates devices.
However, firmware is not involved when devices are added via hotplug, so
the OS may discover power-up errors that should be ignored. The same may
happen when powering up devices when resuming after suspend.
Clear the AER error status registers during enumeration and resume.
[bhelgaas: changelog, remove repetitive comments]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit ad67b437f187ea818b2860524d10f878fadfdd99 upstream.
b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
[bhelgaas: changelog]
Fixes: b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b84106b4e2290c081cdab521fa832596cdfea246 upstream.
The PCI config header (first 64 bytes of each device's config space) is
defined by the PCI spec so generic software can identify the device and
manage its usage of I/O, memory, and IRQ resources.
Some non-spec-compliant devices put registers other than BARs where the
BARs should be. When the PCI core sizes these "BARs", the reads and writes
it does may have unwanted side effects, and the "BAR" may appear to
describe non-sensical address space.
Add a flag bit to mark non-compliant devices so we don't touch their BARs.
Turn off IO/MEM decoding to prevent the devices from consuming address
space, since we can't read the BARs to find out what that address space
would be.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
extracted.
commit 4d8c8bd6f2062c9988817183a91fe2e623c8aa5e upstream.
Occasionaly PV guests would crash with:
pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16
BUG: unable to handle kernel paging request at 0000000d1a8c0be0
.. snip..
<ffffffff8139ce1b>] find_next_bit+0xb/0x10
[<ffffffff81387f22>] cpumask_next_and+0x22/0x40
[<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120
[<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0
[<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0
[<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110
[<ffffffff81529657>] __device_attach_driver+0xa7/0xb0
[<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0
[<ffffffff81527622>] bus_for_each_drv+0x62/0x90
[<ffffffff8152978d>] __device_attach+0xbd/0x110
[<ffffffff815297fb>] device_attach+0xb/0x10
[<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70
[<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80
[<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0
[<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b
[<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160
[<ffffffff8120900f>] ? put_object+0x2f/0x50
[<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0
[<ffffffff814678ee>] backend_changed+0xe/0x10
[<ffffffff81463a28>] xenwatch_thread+0xc8/0x190
[<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10
which was the result of two things:
When we call pci_scan_root_bus we would pass in 'sd' (sysdata)
pointer which was an 'pcifront_sd' structure. However in the
pci_device_add it expects that the 'sd' is 'struct sysdata' and
sets the dev->node to what is in sd->node (offset 4):
set_dev_node(&dev->dev, pcibus_to_node(bus));
__pcibus_to_node(const struct pci_bus *bus)
{
const struct pci_sysdata *sd = bus->sysdata;
return sd->node;
}
However our structure was pcifront_sd which had nothing at that
offset:
struct pcifront_sd {
int domain; /* 0 4 */
/* XXX 4 bytes hole, try to pack */
struct pcifront_device * pdev; /* 8 8 */
}
That is an hole - filled with garbage as we used kmalloc instead of
kzalloc (the second problem).
This patch fixes the issue by:
1) Use kzalloc to initialize to a well known state.
2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That
way access to the 'node' will access the right offset.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 4ae2182b1e3407de369f8c5d799543b7db74221b upstream.
A Root Port's AER structure (rpc) contains a queue of events. aer_irq()
enqueues AER status information and schedules aer_isr() to dequeue and
process it. When we remove a device, aer_remove() waits for the queue to
be empty, then frees the rpc struct.
But aer_isr() references the rpc struct after dequeueing and possibly
emptying the queue, which can cause a use-after-free error as in the
following scenario with two threads, aer_isr() on the left and a
concurrent aer_remove() on the right:
Thread A Thread B
-------- --------
aer_irq():
rpc->prod_idx++
aer_remove():
wait_event(rpc->prod_idx == rpc->cons_idx)
# now blocked until queue becomes empty
aer_isr(): # ...
rpc->cons_idx++ # unblocked because queue is now empty
... kfree(rpc)
mutex_unlock(&rpc->rpc_mutex)
To prevent this problem, use flush_work() to wait until the last scheduled
instance of aer_isr() has completed before freeing the rpc struct in
aer_remove().
I reproduced this use-after-free by flashing a device FPGA and
re-enumerating the bus to find the new device. With SLUB debug, this
crashes with 0x6b bytes (POISON_FREE, the use-after-free magic number) in
GPR25:
pcieport 0000:00:00.0: AER: Multiple Corrected error received: id=0000
Unable to handle kernel paging request for data at address 0x27ef9e3e
Workqueue: events aer_isr
GPR24: dd6aa000 6b6b6b6b 605f8378 605f8360 d99b12c0 604fc674 606b1704 d99b12c0
NIP [602f5328] pci_walk_bus+0xd4/0x104
[bhelgaas: changelog, stable tag]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit a006482b67a96c16dfefc558e36863c51e1829bf upstream.
This message isn't useful any more, so drop it.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60636
Reported-by: Oleksil Shevchuk <alxchk@gmail.com>
Reference: http://lkml.kernel.org/r/CALCETrWkr53ZjqdN3t7rTTfr=+ZKZXJoYsuBcwPf0kN_33GfAw@mail.gmail.com
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit d1541dc977d376406f4584d8eb055488655c98ec upstream.
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 7aa6ca4d39edf01f997b9e02cf6d2fdeb224f351 upstream.
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 932c435caba8a2ce473a91753bad0173269ef334 upstream.
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 50b52fdee050745935d92e7026373edea2647e60 upstream.
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[backported for SLE12]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.com>
|
|
commit 16b036af31e1456cb69243a5a0c9ef801ecd1f17 upstream.
If the image size would ever read as 0, pci_get_rom_size() could keep
processing the same image over and over again. Exit the loop if we ever
read a length of zero.
This fixes a soft lockup on boot when the radeon driver calls
pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card.
[bhelgaas: changelog, reference]
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973
Reported-by: Federico <federicotg@gmail.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 145b3fe579db66fbe999a2bc3fd5b63dffe9636d upstream.
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
Commit 89ec3dcf17fd ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem. Some udev implementations rely on
the uevent file and not the modalias file.
Fixes: d1ded203adf1 ("PCI: add MODALIAS to hotplug event for pci devices")
Fixes: 89ec3dcf17fd ("PCI: Generate uppercase hex for modalias interface class")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 36e8164882ca6d3c41cb91e6f09a3ed236841f80 upstream.
Commit 6ac665c63dca ("PCI: rewrite PCI BAR reading code") masked off
low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(),
which compares 'base == maxbase' to check for read-only BARs. The masking
of 'l' means that comparison will never be 'true', so the check for
read-only BARs no longer works.
Resolve this by also masking off the low-order bits of 'sz' before passing
it into pci_size() as 'maxbase'. With this change, pci_size() will once
again catch the problems that have been encountered to date:
- AGP aperture BAR of AMD-7xx host bridges: if the AGP window is
disabled, this BAR is read-only and read as 0x00000008 [1]
- BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1]
- Intel Sandy Bridge - Thermal Management Controller [8086:0103];
BAR 0 returning 0xfed98004 [2]
- Intel Xeon E5 v3/Core i7 Power Control Unit [8086:2fc0];
Bar 0 returning 0x00001a [3]
Link: [1] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/drivers/pci/probe.c?id=1307ef6621991f1c4bc3cec1b5a4ebd6fd3d66b9 ("PCI: probing read-only BARs" (pre-git))
Link: [2] https://bugzilla.kernel.org/show_bug.cgi?id=43331
Link: [3] https://bugzilla.kernel.org/show_bug.cgi?id=85991
Reported-by: William Unruh <unruh@physics.ubc.ca>
Reported-by: Martin Lucina <martin@lucina.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit f144d1496b47e7450f41b767d0d91c724c2198bc upstream.
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 2adc7907bac2c72535894732c4b41f9210f9e577 upstream.
If populate_msi_sysfs() function failed msix_capability_init() must return
the error code, but it returns the success instead. This update fixes the
described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 89ec3dcf17fd3fa009ecf8faaba36828dd6bc416 upstream.
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
[bhelgaas: changelog]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 9fe373f9997b48fcd6222b95baf4a20c134b587a upstream.
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too]
Signed-off-by: Douglas Lehr <dllehr@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 56fab6e189441d714a2bfc8a64f3df9c0749dff7 upstream.
Geert Uytterhoeven reported a warning when building pci-mvebu:
drivers/pci/host/pci-mvebu.c: In function 'mvebu_get_tgt_attr':
drivers/pci/host/pci-mvebu.c:887:39: warning: 'rtype' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (slot == PCI_SLOT(devfn) && type == rtype) {
^
And indeed, the code of mvebu_get_tgt_attr() may lead to the usage of rtype
when being uninitialized, even though it would only happen if we had
entries other than I/O space and 32 bits memory space.
This commit fixes that by simply skipping the current DT range being
considered, if it doesn't match the resource type we're looking for.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 1f6ae47ecff7f23da73417e068018b311f3b5583 upstream.
We can't do ASPM configuration at enumeration-time because enabling it
makes some defective hardware unresponsive, even if ASPM is disabled later
(see 41cd766b0659 ("PCI: Don't enable aspm before drivers have had a chance
to veto it"). Therefore, we have to do it after a driver claims the
device.
We previously configured ASPM in pci_set_power_state(), but that's not a
very good place because it's not really related to setting the PCI device
power state, and doing it there means:
- We incorrectly skipped ASPM config when setting a device that's
already in D0 to D0.
- We unnecessarily configured ASPM when setting a device to a low-power
state (the ASPM feature only applies when the device is in D0).
- We unnecessarily configured ASPM when called from a .resume() method
(ASPM configuration needs to be restored during resume, but
pci_restore_pcie_state() should already do this).
Move ASPM configuration from pci_set_power_state() to
do_pci_enable_device() so we do it when a driver enables a device.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=79621
Fixes: db288c9c5f9d ("PCI / PM: restore the original behavior of pci_set_power_state()")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vidya Sagar <sagar.tv@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 761ce53330a4f02c58768631027d1c1dd0d538f7 upstream.
Numerical values stored in the device tree are encoded in Big Endian and
should be byte swapped when running in Little Endian.
The RPA hotplug module should convert those values as well.
Note that in rpaphp_get_drc_props(), the comparison between indexes[i+1]
and *index is done using the BE values (whatever is the current endianess).
This doesn't matter since we are checking for equality here. This way only
the returned value is byte swapped.
RPA also made RTAS calls which implies BE values to be used. According to
the patch done in RTAS (http://patchwork.ozlabs.org/patch/336865), no
additional conversion is required in RPA.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 67ebd8140dc8923c65451fa0f6a8eee003c4dcd3 upstream.
3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 7c82126a94e69bbbac586f0249e7ef11e681246c upstream.
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa96f ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa96f reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 93fa9d32670f5592c8e56abc9928fc194e1e72fc upstream.
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6c1 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b6d07e0273d3296cfbdc88145b8a00ddbefb310a upstream.
mvebu_pcie_handle_membase_change() and
mvebu_pcie_handle_iobase_change() do not correctly compute the window
size. PCI uses an inclusive start/end address pair, which requires a
+1 when converting to size.
This only worked because a bug in the mbus driver allowed it to
silently accept and round up bogus sizes.
Fix this by adding one to the computed size.
Fixes: 45361a4fe446 ('PCIe driver for Marvell Armada 370/XP systems')
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-5-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 4f4bde1df33bde076f53325bdf2c6430cf85e1bb upstream.
The second parameter of of_read_number() is not the index, but a size. As
it happens, in this case it may work just fine because of the conversion to
u32 and the favorable endianness on this architecture.
Fixes: 11be65472a427 ("PCI: mvebu: Adapt to the new device tree layout")
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 017fcdc30cdae18c0946eef1ece1f14b4c7897ba upstream.
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit dbffdd6862e67d60703f2df66c558bf448f81d6e upstream.
The Synopsys PCIe core provides one pair of 32-bit BARs (BAR 0 and BAR 1).
The BARs can be configured as follows:
- One 64-bit BAR: BARs 0 and 1 are combined to form a single 64-bit BAR
- Two 32-bit BARs: BARs 0 and 1 are two independent 32-bit BARs
This patch corrects 64-bit, non-prefetchable memory BAR configuration
implemented in dw driver.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b42285f66f871a9898a0e79e2d74bc7e7a101995 upstream.
The clock passed to PCI controller found on MVEBU SoCs may come from a
clock gate. This requires the clock to be enabled before any registers
are accessed. Therefore, move the clock enable before register iomap to
ensure it is enabled.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 3cdeb713dc66057b50682048c151eae07b186c42 upstream.
Andreas reported that after 1f42db786b14 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.
This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.
Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device(). But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.
This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.
Fixes: 1f42db786b14 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit fbeeb822f6f45cadf154d7b7cff1c13537cd799d upstream.
f41f064cf4 ("PCI: Workaround missing pci_set_master in pci drivers") made
pci_enable_bridge() turn on bus mastering if the driver hadn't done so
already. It also added a warning in this case. But there's no reason to
warn about it unless it's actually a problem to enable bus mastering here.
This patch drops the warning because I'm not aware of any such problem.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 1f42db786b14a31bf807fc41ee5583a00c08fcb1 upstream.
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 322a8e91844f4ae2093e0d3d8a318d0ef2596756 upstream.
Marvell SoCs place the SoC number into the PCIe endpoint device ID. The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.
The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.
When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality. Debian would
like to use this in order to aid installing the correct DTB file.
Fixes: 45361a4fe4464 ("pci: PCIe driver for Marvell Armada 370/XP systems")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 7282059489868e0ed1b0d79765730c6b233a8399 upstream.
The ACPI specification (ACPI 5.0A, Section 6.3.7) says:
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which
no device driver should be loaded (for example, a bridge device.)
Children of this device may be present and valid. OSPM should
continue enumeration below a device whose _STA returns this bit
combination.
Evidently, some BIOSes follow that and return 0x0A from _STA, which
causes problems to happen when they trigger bus check or device check
notifications for those devices too. Namely, ACPIPHP thinks that they
are gone and may drop them, for example, if such a notification is
triggered during a resume from system suspend.
To fix that, modify ACPICA to regard devies as present and
functioning if _STA returns both the ACPI_STA_DEVICE_ENABLED
and ACPI_STA_DEVICE_FUNCTIONING bits set for them.
Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com>
[rjw: Subject and changelog, minor code modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51c71a3bbaca868043cc45b3ad3786dd48a90235 upstream.
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f244d8b623dae7a7bc695b0336f67729b95a9736 upstream.
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f26ca1d699e8b54a50d9faf82327d3c2072aaedd upstream.
acpiphp_enumerate_slots() walks ACPI namenamespace under
a PCI host bridge with callback register_slot().
register_slot() evaluates _ADR for all the device objects
and emits a warning message for any error. Some platforms
have _HID device objects (such as HPET and IPMI), which
trigger unnecessary warning messages.
This patch avoids emitting a warning message when a target
device object does not have _ADR.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fc9bbf98fd66f879e628d8537ba7c240be2b58e upstream.
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c2332 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7cc5cf74544d97d7b69e2701595037474db1f96 upstream.
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 2dc4128 (ACPI / hotplug / PCI: Avoid doing too much for
spurious notifies) changed the enable_slot() to check return value of
pci_scan_slot() and if it is zero return early from the function. It
means that there were no new devices in this particular slot.
However, if a device appeared deeper in the hierarchy the code now
ignores it causing things like Thunderbolt chaining fail to recognize
new devices.
The problem with Alex Williamson's machine was solved with commit
a47d8c8 (ACPI / hotplug / PCI: Avoid parent bus rescans on spurious
device checks) and hence we should be able to restore the original
functionality that we always rescan on bus check notification.
On a device check notification we still check what acpiphp_rescan_slot()
returns and on zero bail out early.
Fixes: 2dc41281b1d1 (ACPI / hotplug / PCI: Avoid doing too much for spurious notifies)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The WARN_ON() in acpiphp_enumerate_slots() triggers unnecessarily for
devices whose bridges are going to be handled by native PCIe hotplug
(pciehp) and the simplest way to prevent that from happening is to
drop the WARN_ON().
References: https://bugzilla.kernel.org/show_bug.cgi?id=62831
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
One of the error code paths in acpiphp_enumerate_slots() is missing
a pci_dev_put(bridge->pci_dev) call, so add it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Ben Herrenschmidt found that commit 928bea964827 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.
The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.
Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.
Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.
That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 448bd85 (PCI/PM: add PCIe runtime D3cold support) added a
piece of code to pci_acpi_wake_dev() causing that function to behave
in a special way for devices in D3cold (so that their configuration
registers are not accessed before those devices are resumed).
However, it didn't take the clearing of the pme_poll flag into
account. That has to be done for all devices, even if they are in
D3cold, or pci_pme_list_scan() will not know that wakeup has been
signaled for the device and will poll its PME Status bit
unnecessarily.
Fix the problem by moving the clearing of the pme_poll flag in
pci_acpi_wake_dev() before the code introduced by commit 448bd85.
Reported-and-tested-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.6+ <stable@vger.kernel.org> # 3.6+
|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"All of these commits are fixes that have emerged recently and some of
them fix bugs introduced during this merge window.
Specifics:
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting
breakage on a system that triggers device check notifications
during boot for non-existing devices. Although those
notifications are really spurious, we should be able to deal with
them nevertheless and that shouldn't introduce too much overhead.
Four commits to make that work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the
information expected by the driver. Fix from Mika Westerberg, for
stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice).
From Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one
that the BIOS expects us to choose, so this makes the lookup take
more criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with
cpufreq related to CPU hotplug which are addressed by a series of
fixes from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state
won't work correcty if cputime_t doesn't map directly to jiffies.
Fix from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency
problems in cpufreq related to the ordering of transitions, but
unfortunately it introduced several problems of its own, so I
decided to revert it now and address the original problems later
in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs
attributes over suspend/resume cycles introduced a possible NULL
pointer dereference that caused it to crash during the second
attempt to suspend. Three commits from Srivatsa S Bhat fix that
problem and a couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu"
* tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
cpufreq: Acquire the lock in cpufreq_policy_restore() for reading
cpufreq: Prevent problems in update_policy_cpu() if last_cpu == new_cpu
cpufreq: Restructure if/else block to avoid unintended behavior
cpufreq: Fix crash in cpufreq-stats during suspend/resume
intel_pstate: Add Haswell CPU models
Revert "cpufreq: make sure frequency transitions are serialized"
cpufreq: Use signed type for 'ret' variable, to store negative error values
cpufreq: Remove temporary fix for race between CPU hotplug and sysfs-writes
cpufreq: Synchronize the cpufreq store_*() routines with CPU hotplug
cpufreq: Invoke __cpufreq_remove_dev_finish() after releasing cpu_hotplug.lock
cpufreq: Split __cpufreq_remove_dev() into two parts
cpufreq: Fix wrong time unit conversion
cpufreq: serialize calls to __cpufreq_governor()
cpufreq: don't allow governor limits to be changed when it is disabled
ACPI / bind: Prefer device objects with _STA to those without it
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPICA: Fix for a Store->ArgX when ArgX contains a reference to a field.
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
...
|
|
* acpi-pci-hotplug:
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
|
|
In the current ACPIPHP notify handler we always go directly for a
rescan of the parent bus if we get a device check notification for
a device that is not a bridge. However, this obviously is
overzealous if nothing really changes, because this way we may rescan
the whole PCI hierarchy pretty much in vain.
That happens on Alex Williamson's machine whose ACPI tables contain
device objects that are supposed to coresspond to PCIe root ports,
but those ports aren't physically present (or at least they aren't
visible in the PCI config space to us). The BIOS generates multiple
device check notifies for those objects during boot and for each of
them we go straight for the parent bus rescan, but the parent bus is
the root bus in this particular case. In consequence, we rescan the
whole PCI bus from the top several times in a row, which is
completely unnecessary, increases boot time by 50% (after previous
fixes) and generates excess dmesg output from the PCI subsystem.
Fix the problem by checking if we can find anything new in the
slot corresponding to the device we've got a device check notify
for and doing nothig if that's not the case.
The spec (ACPI 5.0, Section 5.6.6) appears to mandate this behavior,
as it says:
Device Check. Used to notify OSPM that the device either appeared
or disappeared. If the device has appeared, OSPM will re-enumerate
from the parent. If the device has disappeared, OSPM will
invalidate the state of the device. OSPM may optimize out
re-enumeration.
Therefore, according to the spec, we are free to do nothing if
nothing changes.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60865
Reported-and-tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
