summaryrefslogtreecommitdiff
path: root/drivers/pci/controller/dwc/pcie-qcom-ep.c
AgeCommit message (Collapse)Author
2024-11-25Merge branch 'pci/controller/qcom'Bjorn Helgaas
- Enable MSI interrupts if 'global' IRQ is supported, since a previous commit unintentionally masked them (Manivannan Sadhasivam) - Move endpoint controller cleanups that depend on refclk from the host to the notifier that tells us the host has deasserted PERST# (Manivannan Sadhasivam) - Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a and Qcom IP 1.27.0 (devi priya) - Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom platforms (Qiang Yu) - Add 'global' SPI interrupt for events like link-up, link-down to qcom,pcie-x1e80100 DT binding so we can start enumeration when the link comes up (Qiang Yu) - Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to support this (Qiang Yu) - Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map' DT property and doesn't need BDF-to-SID translation (Qiang Yu) * pci/controller/qcom: PCI: qcom: Disable ASPM L0s for X1E80100 PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml PCI: qcom: Add support for IPQ9574 dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert() PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
2024-11-03PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()Manivannan Sadhasivam
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF deinit notify function pci_epc_deinit_notify() are called during the execution of qcom_pcie_perst_assert() i.e., when the host has asserted PERST#. But quickly after this step, refclk will also be disabled by the host. All of the Qcom endpoint SoCs supported as of now depend on the refclk from the host for keeping the controller operational. Due to this limitation, any access to the hardware registers in the absence of refclk will result in a whole endpoint crash. Unfortunately, most of the controller cleanups require accessing the hardware registers (like eDMA cleanup performed in dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup functions are currently causing the crash in the endpoint SoC once host asserts PERST#. One way to address this issue is by generating the refclk in the endpoint itself and not depending on the host. But that is not always possible as some of the endpoint designs do require the endpoint to consume refclk from the host (as I was told by the Qcom engineers). Thus, fix this crash by moving the controller cleanups to the start of the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is called whenever the host has deasserted PERST# and it is guaranteed that the refclk would be active at this point. So at the start of this function (after enabling resources), the controller cleanup can be performed. Once finished, rest of the code execution for PERST# deassert can continue as usual. Fixes: 473b2cf9c4d1 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers") Fixes: 570d7715eed8 ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#") Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2024-10-03PCI: controller: Switch back to struct platform_driver::remove()Sergio Paracuellos
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all PCI controller drivers to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. Link: https://lore.kernel.org/r/20240923065706.728769-1-sergio.paracuellos@gmail.com Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> [bhelgaas: add pcie-xilinx-nwl.c and tidy whitespace per Uwe Kleine-König: https://lore.kernel.org/r/tdxrmmqyzcufupnwkdbg7lwgadizm7v3lxjirykijbml7x54ze@upbdzycdsilm] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-09-23Merge tag 'pci-v6.12-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Wait for device readiness after reset by polling Vendor ID and looking for Configuration RRS instead of polling the Command register and looking for non-error completions, to avoid hardware retries done for RRS on non-Vendor ID reads (Bjorn Helgaas) - Rename CRS Completion Status to RRS ('Request Retry Status') to match PCIe r6.0 spec usage (Bjorn Helgaas) - Clear LBMS bit after a manual link retrain so we don't try to retrain a link when there's no downstream device anymore (Maciej W. Rozycki) - Revert to the original link speed after retraining fails instead of leaving it restricted to 2.5GT/s, so a future device has a chance to use higher speeds (Maciej W. Rozycki) - Wait for each level of downstream bus, not just the first, to become accessible before restoring devices on that bus (Ilpo Järvinen) - Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups without having to stomp on the core's pdev->dev.groups (Lukas Wunner) Driver binding: - Export pcim_request_region(), a managed counterpart of pci_request_region(), for use by drivers (Philipp Stanner) - Export pcim_iomap_region() and deprecate pcim_iomap_regions() (Philipp Stanner) - Request the PCI BAR used by xboxvideo (Philipp Stanner) - Request and map drm/ast BARs with pcim_iomap_region() (Philipp Stanner) MSI: - Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a single IRQ line and cannot set the affinity of each MSI to a specific CPU core (Marek Vasut) - Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity() implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3, mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl, xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed' warnings (Marek Vasut) Power management: - Add pwrctl support for ATH11K inside the WCN6855 package (Konrad Dybcio) PCI device hotplug: - Remove unnecessary hpc_ops struct from shpchp (ngn) - Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp (weiyufeng) Virtualization: - Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson) - Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS but does provide ACS-like features (Subramanian Ananthanarayanan) IOMMU: - Add function 0 DMA alias quirk for Glenfly Arise audio function, which uses the function 0 Requester ID (WangYuli) NPEM: - Add Native PCIe Enclosure Management (NPEM) support for sysfs control of NVMe RAID storage indicators (ok/fail/locate/ rebuild/etc) (Mariusz Tkaczyk) - Add support for the ACPI _DSM PCIe SSD status LED management, which is functionally similar to NPEM but mediated by platform firmware (Mariusz Tkaczyk) Device trees: - Drop minItems and maxItems from ranges in PCI generic host binding since host bridges may have several MMIO and I/O port apertures (Frank Li) - Add kirin, rcar-gen2, uniphier DT binding top-level constraints for clocks (Krzysztof Kozlowski) Altera PCIe controller driver: - Convert altera DT bindings from text to YAML (Matthew Gerlach) - Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing and is what other drivers use (Jinjie Ruan) Broadcom STB PCIe controller driver: - Add DT binding maxItems for reset controllers (Jim Quinlan) - Use the 'bridge' reset method if described in the DT (Jim Quinlan) - Use the 'swinit' reset method if described in the DT (Jim Quinlan) - Add 'has_phy' so the existence of a 'rescal' reset controller doesn't imply software control of it (Jim Quinlan) - Add support for many inbound DMA windows (Jim Quinlan) - Rename SoC 'type' to 'soc_base' express the fact that SoCs come in families of multiple similar devices (Jim Quinlan) - Add Broadcom 7712 DT description and driver support (Jim Quinlan) - Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for maintainability (Bjorn Helgaas) Freescale i.MX6 PCIe controller driver: - Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints (Richard Zhu) - Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints to fail to establish link (Richard Zhu) - Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing outbound alignment requirement (Richard Zhu) - Call phy_power_off() in the .probe() error path (Frank Li) - Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also supported (Frank Li) - Manage Refclk by using SoC-specific callbacks instead of switch statements (Frank Li) - Manage core reset by using SoC-specific callbacks instead of switch statements (Frank Li) - Expand comments for erratum ERR010728 workaround (Frank Li) - Use generic PHY APIs to configure mode, speed, and submode, which is harmless for devices that implement their own internal PHY management and don't set the generic imx_pcie->phy (Frank Li) - Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root Complex support (Richard Zhu) Freescale Layerscape PCIe controller driver: - Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with fsl,lx2160ar2-pcie (Frank Li) - Add layerscape-pcie DT binding deprecated 'num-viewport' property to address a DT checker warning (Frank Li) - Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array (Frank Li) Loongson PCIe controller driver: - Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets (Huacai Chen) Marvell Aardvark PCIe controller driver: - Fix issue with emulating Configuration RRS for two-byte reads of Vendor ID; previously it only worked for four-byte reads (Bjorn Helgaas) MediaTek PCIe Gen3 controller driver: - Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC types (Lorenzo Bianconi) - Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi) - Add DT and driver support for Airoha EN7581 PCIe controller (Lorenzo Bianconi) Qualcomm PCIe controller driver: - Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan Ansari) - Add back DT 'vddpe-3v3-supply', which was incorrectly removed earlier (Johan Hovold) - Drop endpoint redundant masking of global IRQ events (Manivannan Sadhasivam) - Clarify unknown global IRQ message and only log it once to avoid a flood (Manivannan Sadhasivam) - Add 'linux,pci-domain' property to endpoint DT binding (Manivannan Sadhasivam) - Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam) - Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint controller (Manivannan Sadhasivam) - Add global SPI interrupt for PCIe link events to DT binding (Manivannan Sadhasivam) - Add global RC interrupt handler to handle 'Link up' events and automatically enumerate hot-added devices (Manivannan Sadhasivam) - Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR MMIO space (Prudhvi Yarlagadda) - Enable controller resources like PHY only after PERST# is deasserted to partially avoid the problem that the endpoint SoC crashes when accessing things when Refclk is absent (Manivannan Sadhasivam) - Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu Chinta Venkata) - Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a NULL pointer dereference (Manivannan Sadhasivam) Renesas R-Car PCIe controller driver: - Make the read-only const array 'check_addr' static (Colin Ian King) - Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding (Yoshihiro Shimoda) TI DRA7xx PCIe controller driver: - Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler is NULL (Siddharth Vadapalli) - Handle IRQ request errors during root port and endpoint probe (Siddharth Vadapalli) TI J721E PCIe driver: - Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable the ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli) - Extract the cadence link setup from cdns_pcie_host_setup() so link setup can be done separately during resume (Thomas Richard) - Add T_PERST_CLK_US definition for the mandatory delay between Refclk becoming stable and PERST# being deasserted (Thomas Richard) - Add j721e suspend and resume support (Théo Lebrun) TI Keystone PCIe controller driver: - Fix NULL pointer checking when applying MRRS limitation quirk for AM65x SR 1.0 Errata #i2037 (Dan Carpenter) Xilinx NWL PCIe controller driver: - Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to be lost or delivered as the wrong interrupt (Sean Anderson) - Rate-limit misc interrupt messages (Sean Anderson) - Turn off the clock on probe failure and device removal (Sean Anderson) - Add DT binding and driver support for enabling/disabling PHYs (Sean Anderson) - Add PCIe phy bindings for the ZCU102 (Sean Anderson) Xilinx XDMA PCIe controller driver: - Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding and xilinx-dma-pl driver (Thippeswamy Havalige) Miscellaneous: - Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina) - Fix minor kerneldoc issues and typos (Bjorn Helgaas) - Use PCI_DEVID() macro in aer_inject() instead of open-coding it (Jinjie Ruan) - Check pcie_find_root_port() return in x86 fixups to avoid NULL pointer dereferences (Samasth Norway Ananda) - Make pci_bus_type constant (Kunwu Chan) - Remove unused declarations of __pci_pme_wakeup() and pci_vpd_release() (Yue Haibing) - Remove any leftover .*.cmd files with make clean (zhang jiao) - Remove unused BILLION macro (zhang jiao)" * tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits) PCI: Fix typos dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again tools: PCI: Remove unused BILLION macro tools: PCI: Remove .*.cmd files with make clean PCI: Pass domain number to pci_bus_release_domain_nr() explicitly PCI: dra7xx: Fix error handling when IRQ request fails in probe PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ PCI: qcom: Add RX lane margining settings for 16.0 GT/s PCI: qcom: Add equalization settings for 16.0 GT/s PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed' PCI: qcom-ep: Enable controller resources like PHY only after refclk is available PCI: Mark Creative Labs EMU20k2 INTx masking as broken dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint dt-bindings: PCI: altera: msi: Convert to YAML PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support PCI: Rename CRS Completion Status to RRS PCI: aardvark: Correct Configuration RRS checking PCI: Wait for device readiness with Configuration RRS PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings ...
2024-09-13PCI: qcom: Add RX lane margining settings for 16.0 GT/sShashank Babu Chinta Venkata
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate. These settings improve link stability while operating at high date rates and helps to improve signal quality. Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org Tested-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com> [mani: dropped the code refactoring and minor changes] Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> [kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-09-13PCI: qcom: Add equalization settings for 16.0 GT/sShashank Babu Chinta Venkata
During high data transmission rates such as 16.0 GT/s, there is an increased risk of signal loss due to poor channel quality and interference. This can impact receiver's ability to capture signals accurately. Hence, as signal compensation is achieved through appropriate lane equalization, apply lane equalization settings at both transmitter and receiver which results in an increase in the PCIe signal strength. While at it, modify the pcie-tegra194 driver to make use of the common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h. Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org Tested-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com> [mani: dropped the code refactoring and minor changes] Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> [kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-09-13PCI: qcom-ep: Enable controller resources like PHY only after refclk is ↵Manivannan Sadhasivam
available qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it enables the controller resources like clocks, regulator, PHY. On one of the new unreleased Qcom SoC, PHY enablement depends on the active refclk. And on all of the supported Qcom endpoint SoCs, refclk comes from the host (RC). So calling qcom_pcie_enable_resources() without refclk causes the NoC (Network On Chip) error in the endpoint SoC and in turn results in a whole SoC crash and rebooting into EDL (Emergency Download) mode which is an unrecoverable state. But qcom_pcie_enable_resources() is already called by qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is available at that time. Hence, remove the unnecessary call to qcom_pcie_enable_resources() from qcom_pcie_ep_probe() to prevent the above mentioned crash. It should be noted that this commit prevents the crash only under normal working condition (booting endpoint before host), but the crash may also occur if PERST# assert happens at the wrong time. For avoiding the crash completely, it is recommended to use SRIS mode which allows the endpoint SoC to generate its own refclk. The driver is not supporting SRIS mode currently, but will be added in the future. Fixes: 869bc5253406 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host") Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2024-09-01PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device namesManivannan Sadhasivam
Currently, the IRQ device name for both of these IRQs doesn't have Qcom specific prefix and PCIe domain number. This causes 2 issues: 1. Pollutes the global IRQ namespace since 'global' is a common name. 2. When more than one EP controller instance is present in the SoC, naming conflict will occur. Hence, add 'qcom_pcie_ep_' prefix and PCIe domain number suffix to the IRQ names to uniquely identify the IRQs and also to fix the above mentioned issues. Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-6-263a385fbbcb@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
2024-09-01PCI: qcom-ep: Reword the error message for receiving unknown global IRQ eventManivannan Sadhasivam
Current error message just prints the contents of PARF_INT_ALL_STATUS register as if like the IRQ event number. It could mislead the users. Reword it to make it clear that the error message is actually showing the interrupt status register to help debug spurious IRQ events. While at it, let's also switch over to dev_WARN_ONCE() so that any IRQ storm won't flood the kernel log buffer. Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-2-263a385fbbcb@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
2024-09-01PCI: qcom-ep: Drop the redundant masking of global IRQ eventsManivannan Sadhasivam
Once the events are disabled in PARF_INT_ALL_MASK register, only the enabled events will generate global IRQ. So there is no need to do the masking again in the IRQ handler, drop it. If there are any spurious IRQs getting generated, they will be reported using the existing dev_err() in the handler. Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-1-263a385fbbcb@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
2024-08-21PCI: qcom-ep: Disable MHI RAM data parity error interrupt for SA8775P SoCManivannan Sadhasivam
SA8775P SoC has support for the hardware parity check feature on the MHI RAM (entity that holds MHI registers, etc.) But due to a hardware bug in the parity check logic, the data parity error interrupt is getting generated all the time when using MHI. So the hardware team has suggested disabling the parity check error to work around the hardware bug. Mask the parity error interrupt in PARF_INT_ALL_5_MASK register. Fixes: 58d0d3e032b3 ("PCI: qcom-ep: Add support for SA8775P SOC") Link: https://lore.kernel.org/linux-pci/20240808063057.7394-1-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-07-19Merge branch 'pci/controller/qcom'Bjorn Helgaas
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid writing out all the clock names (Manivannan Sadhasivam) - Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar) - Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA (HDMA) (Manivannan Sadhasivam) - Enable drivers to supply the eDMA channel count since some can't auto detect this (Manivannan Sadhasivam) - Add HDMA support for the SA8775P SoC (Mrinmay Sarkar) - Override the SA8775P NO_SNOOP default to avoid possible memory corruption (Mrinmay Sarkar) - Make sure resources are disabled during PERST# assertion, even if the link is already disabled (Manivannan Sadhasivam) - Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active even if other drivers don't vote for it (Krishna chaitanya chundru) - Add Operating Performance Points (OPP) to scale performance state based on aggregate link bandwidth to improve SoC power efficiency (Krishna chaitanya chundru) - Return failure instead of success if dev_pm_opp_find_freq_floor() fails (Dan Carpenter) - Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails (Dan Carpenter) - Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan Carpenter) * pci/controller/qcom: PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq() PCI: qcom: Prevent potential error pointer dereference PCI: qcom: Fix missing error code in qcom_pcie_probe() PCI: qcom: Add OPP support to scale performance PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps() PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path PCI: qcom-ep: Disable resources unconditionally during PERST# assert PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP PCI: qcom: Override NO_SNOOP attribute for SA8775P RC PCI: epf-mhi: Enable HDMA for SA8775P SoC PCI: qcom-ep: Add HDMA support for SA8775P SoC PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers PCI: dwc: Skip finding eDMA channels count for HDMA platforms PCI: dwc: Refactor dw_pcie_edma_find_chip() API PCI: qcom-ep: Add support for SA8775P SOC dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC PCI: qcom: Use devm_clk_bulk_get_all() API
2024-07-09PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down ↵Manivannan Sadhasivam
event Now that the generic dw_pcie_ep_linkdown() API is available, use it. This also handles the reinitialization of DWC non-sticky registers in addition to sending the notification to EPF drivers. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapperManivannan Sadhasivam
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify() directly, so this wrapper provides no benefit to the glue drivers. Remove it and call pci_epc_init_notify() directly from glue drivers. Suggested-by: Bjorn Helgaas <helgaas@kernel.org> Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: qcom-ep: Disable resources unconditionally during PERST# assertManivannan Sadhasivam
All EP specific resources are enabled during PERST# deassert. As a counter operation, all resources should be disabled during PERST# assert. There is no point in skipping that if the link was not enabled. This will also result in enablement of the resources twice if PERST# got deasserted again. So remove the check from qcom_pcie_perst_assert() and disable all the resources unconditionally. Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver") Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EPMrinmay Sarkar
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute in its TLP for all the PCIe controllers. NO_SNOOP attribute when set, the requester is indicating that no cache coherency issues exist for the addressed memory on the host i.e., memory is not cached. But in reality, requester cannot assume this unless there is a complete control/visibility over the addressed memory on the host. And worst case, if the memory is cached on the host, it may lead to memory corruption issues. It should be noted that the caching of memory on the host is not solely dependent on the NO_SNOOP attribute in TLP. So to avoid the corruption, this patch overrides the NO_SNOOP attribute by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not needed for other upstream supported platforms since they do not set NO_SNOOP attribute by default. Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-07-04PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF driversManivannan Sadhasivam
As like the 'epc_init' event, that is used to signal the EPF drivers about the EPC initialization, let's introduce 'epc_deinit' event that is used to signal EPC deinitialization. The EPC deinitialization applies only when any sort of fundamental reset is supported by the endpoint controller as per the PCIe spec. Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1. Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support PERST# as the fundamental reset. So the 'deinit' event will be notified to the EPF drivers when PERST# assert happens in the above mentioned EPC drivers. The EPF drivers, on receiving the event through the epc_deinit() callback should reset the EPF state machine and also cleanup any configuration that got affected by the fundamental reset like BAR, DMA etc... This change also warrants skipping the cleanups in unbind() if already done in epc_deinit(). Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Frank Li <Frank.Li@nxp.com>
2024-05-28PCI: endpoint: Rename BME to Bus Master EnableManivannan Sadhasivam
BME which stands for 'Bus Master Enable' is not defined in the PCIe base spec even though it is commonly referred in many places (vendor docs). To align with the spec, rename it to its expansion 'Bus Master Enable'. Suggested-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: squash removal of irrelevant 'Link is enabled'] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: qcom-ep: Add HDMA support for SA8775P SoCMrinmay Sarkar
SA8775P SoC supports the new Hyper DMA (HDMA) DMA Engine inside the DWC IP, so add support for it by passing the mapping format and the number of read/write channels count. The PCIe EP controller used on this SoC is of version 1.34.0, so a separate config struct is introduced for the sake of enabling HDMA conditionally. It should be noted that for the eDMA support (predecessor of HDMA), there are no mapping format and channels count specified. That is because eDMA supports auto detection of both parameters, whereas HDMA doesn't. [mani: reworded commit message, added kdoc, and minor cleanups] Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-4-f04c5cdde760@linaro.org Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <frank.li@nxp.com> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
2024-05-28PCI: qcom-ep: Add support for SA8775P SOCMrinmay Sarkar
Add support for SA8775P SoC to the Qualcomm PCIe Endpoint Controller driver. Adding new compatible string as it has different set of clocks compared to other SoCs. Link: https://lore.kernel.org/linux-pci/1714492540-15419-3-git-send-email-quic_msarkar@quicinc.com Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-04-10PCI: endpoint: Remove "core_init_notifier" flagManivannan Sadhasivam
"core_init_notifier" flag is set by the glue drivers requiring refclk from the host to complete the DWC core initialization. Also, those drivers will send a notification to the EPF drivers once the initialization is fully completed using the pci_epc_init_notify() API. Only then, the EPF drivers will start functioning. For the rest of the drivers generating refclk locally, EPF drivers will start functioning post binding with them. EPF drivers rely on the 'core_init_notifier' flag to differentiate between the drivers. Unfortunately, this creates two different flows for the EPF drivers. So to avoid that, let's get rid of the "core_init_notifier" flag and follow a single initialization flow for the EPF drivers. This is done by calling the dw_pcie_ep_init_notify() from all glue drivers after the completion of dw_pcie_ep_init_registers() API. This will allow all the glue drivers to send the notification to the EPF drivers once the initialization is fully completed. Only difference here is that, the drivers requiring refclk from host will send the notification once refclk is received, while others will send it during probe time itself. But this also requires the EPC core driver to deliver the notification after EPF driver bind. Because, the glue driver can send the notification before the EPF drivers bind() and in those cases the EPF drivers will miss the event. To accommodate this, EPC core is now caching the state of the EPC initialization in 'init_complete' flag and pci-ep-cfs driver sends the notification to EPF drivers based on that after each EPF driver bind. Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-8-082625472414@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-04-10PCI: dwc: ep: Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers()Manivannan Sadhasivam
The goal of the dw_pcie_ep_init_complete() API is to initialize the DWC specific registers post registering the controller with the EP framework. But the naming doesn't reflect its functionality and causes confusion. So, let's rename it to dw_pcie_ep_init_registers() to make it clear that it initializes the DWC specific registers. Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-6-082625472414@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-04-10PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#Manivannan Sadhasivam
For DWC glue drivers supporting PERST# (currently Qcom and Tegra194), some of the DWC resources like eDMA should be cleaned up during the PERST# assert time. So let's introduce a dw_pcie_ep_cleanup() API that could be called by these drivers to cleanup the DWC specific resources. Currently, it just removes eDMA. Closes: https://lore.kernel.org/linux-pci/ZWYmX8Y%2F7Q9WMxES@x1-carbon Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-5-082625472414@linaro.org Reported-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-01-15Merge branch 'pci/irq-clean-up'Bjorn Helgaas
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more explicit and match spec terminology (Bjorn Helgaas) - Use existing PCI_IRQ_INTX, PCI_IRQ_MSI, PCI_IRQ_MSIX in artpec6, cadence, designware, designware-plat, dra7xx, imx6, keembay, keystone, layerscape, mhi, ntb, qcom, rcar, rcar-gen4, rockchip, tegra194, uniphier, vntb; drop the redundant pci_epc_irq_type enum with the same values (Damien Le Moal) - Use "intx" instead of "leg" or "legacy" when describing INTx interrupts in endpoint core, endpoint tests, cadence, dra7xx, designware, dw-rockchip, dwc core, imx6, keystone, layerscape, qcom, rcar-gen4, rockchip, tegra194, uniphier, xilinx-nwl (Damien Le Moal) * pci/irq-clean-up: PCI: xilinx-nwl: Use INTX instead of legacy PCI: rockchip-host: Rename rockchip_pcie_legacy_int_handler() PCI: rockchip-ep: Use INTX instead of legacy PCI: uniphier: Use INTX instead of legacy PCI: tegra194: Use INTX instead of legacy PCI: dw-rockchip: Rename rockchip_pcie_legacy_int_handler() PCI: keystone: Use INTX instead of legacy PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq() PCI: cadence: Use INTX instead of legacy PCI: dra7xx: Rename dra7xx_pcie_raise_legacy_irq() misc: pci_endpoint_test: Use INTX instead of LEGACY PCI: endpoint: Rename LEGACY to INTX in test function driver PCI: endpoint: Use INTX instead of legacy PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitions PCI: Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX
2024-01-06PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_opsYoshihiro Shimoda
Since the name of the dw_pcie_ep_ops struct makes it obvious that it's for the PCIe Endpoint, rename the struct member .ep_init to .init. [kwilczynski: commit log] Suggested-by: Serge Semin <fancer.lancer@gmail.com> Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-3-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2023-12-19PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq()Damien Le Moal
Rename the function dw_pcie_ep_raise_legacy_irq() of the Designware endpoint controller driver to dw_pcie_ep_raise_intx_irq() to match the name of the PCI_IRQ_INTX macro. Link: https://lore.kernel.org/r/20231122060406.14695-10-dlemoal@kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
2023-12-18PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitionsDamien Le Moal
linux/pci.h defines the IRQ flags PCI_IRQ_INTX, PCI_IRQ_MSI and PCI_IRQ_MSIX. Let's use these flags directly instead of the endpoint definitions provided by enum pci_epc_irq_type. This removes the need for defining this enum type completely. Link: https://lore.kernel.org/r/20231122060406.14695-3-dlemoal@kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2023-10-28Merge branch 'pci/controller/speed'Bjorn Helgaas
- Use PCIE_SPEED2MBS_ENC() macro in qcom host and endpoint to encode link speed instead of hard-coding the link speed in MBps (Manivannan Sadhasivam) - Use Mbps_to_icc() (not MBps_to_icc()) in tegra194 instead of explicitly doing the bytes-to-bits conversion (Manivannan Sadhasivam) * pci/controller/speed: PCI: tegra194: Use Mbps_to_icc() macro for setting icc speed PCI: qcom-ep: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed PCI: qcom: Use PCIE_SPEED2MBS_ENC() macro for encoding link speed
2023-10-27PCI: qcom-ep: Add dedicated callback for writing to DBI2 registersManivannan Sadhasivam
The DWC core driver exposes the write_dbi2() callback for writing to the DBI2 registers in a vendor-specific way. On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be asserted before writing to any DBI2 registers and deasserted once done. So, let's implement the callback for the Qcom PCIe EP driver so that the DBI2 writes are correctly handled in the hardware. Without this callback, the DBI2 register writes like BAR size won't go through and as a result, the default BAR size is set for all BARs. [kwilczynski: commit log, renamed function to match the DWC convention] Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver") Suggested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Cc: stable@vger.kernel.org # 5.16+
2023-10-14PCI: qcom-ep: Use PCIE_SPEED2MBS_ENC() macro for encoding link speedManivannan Sadhasivam
Instead of hardcoding the link speed in MBps, use existing PCIE_SPEED2MBS_ENC() macro that does the encoding of the link speed for us. Also, let's Wrap it with QCOM_PCIE_LINK_SPEED_TO_BW() macro to do the conversion to ICC speed. This eliminates the need for a switch case in qcom_pcie_icc_update() and also works for future Gen speeds without any code modifications. Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/linux-pci/20231004164430.39662-2-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
2023-08-29Merge branch 'pci/controller/qcom-ep'Bjorn Helgaas
- Log unknown Qcom Endpoint IRQ events at error level, not debug level (Manivannan Sadhasivam) - Add DT and driver support for qcom interconnect bandwidth voting for "pcie-mem" and "cpu-pcie" interconnects (Krishna chaitanya chundru) * pci/controller/qcom-ep: PCI: qcom-ep: Add ICC bandwidth voting support dt-bindings: PCI: qcom: ep: Add interconnects path PCI: qcom-ep: Treat unknown IRQ events as an error
2023-08-29Merge branch 'pci/controller/qcom-edma'Bjorn Helgaas
- Pass the Qcom Endpoint 4K alignment requirement for outbound windows to the EPF core so EPF drivers can use it (Manivannan Sadhasivam) - Use alignment restriction from EPF core in Qcom EPF MHI driver (Manivannan Sadhasivam) - Add Qcom Endpoint eDMA support by enabling the eDMA IRQ (Manivannan Sadhasivam) - Add Qcom MHI eDMA support (Manivannan Sadhasivam) - Add Qcom Snapdragon SM8450 support to the EPF MHI driver (Manivannan Sadhasivam) - Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup latency (Manivannan Sadhasivam) - Add pci_epc_mem_init() kernel-doc (Manivannan Sadhasivam) * pci/controller/qcom-edma: PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API PCI: epf-mhi: Use iATU for small transfers PCI: epf-mhi: Add support for SM8450 PCI: epf-mhi: Add eDMA support PCI: qcom-ep: Add eDMA support PCI: epf-mhi: Make use of the alignment restriction from EPF core PCI: qcom-ep: Pass alignment restriction to the EPF core
2023-08-29PCI: qcom-ep: Add ICC bandwidth voting supportKrishna chaitanya chundru
Add support for voting interconnect (ICC) bandwidth based on the link speed and width. This commit is inspired from the basic interconnect support added to pcie-qcom driver in commit c4860af88d0c ("PCI: qcom: Add basic interconnect support"). The interconnect support is kept optional to be backward compatible with legacy device trees. [kwilczynski: add missing kernel-doc for the icc_mem variable] Link: https://lore.kernel.org/linux-pci/1689751218-24492-5-git-send-email-quic_krichai@quicinc.com Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2023-08-29PCI: qcom-ep: Treat unknown IRQ events as an errorManivannan Sadhasivam
Sometimes, the Qcom PCIe EP controller can receive some interrupts unknown to the driver, like safety interrupts in newer SoCs. In those cases, if the driver doesn't clear the interrupts, it will end up in an interrupt storm. However, the users will not know about it because the log is treated as a debug message. So let's treat the unknown event log as an error so that it at least makes the user aware, thereby getting fixed eventually. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230726152931.18134-1-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2023-08-26PCI: qcom-ep: Add eDMA supportManivannan Sadhasivam
Qualcomm PCIe Endpoint controllers have the in-built Embedded DMA (eDMA) peripheral for offloading the data transfer between the PCIe bus and memory. Let's add support for it by enabling the eDMA IRQ in the driver. The eDMA DMA Engine driver will handle the rest of the functionality. Since the eDMA on Qualcomm platforms only uses a single IRQ for all channels, use 1 for edma.nr_irqs. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230717065459.14138-4-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2023-08-25PCI: qcom-ep: Pass alignment restriction to the EPF coreManivannan Sadhasivam
Qcom PCIe EP controllers have 4K alignment restriction for the outbound window address. Hence, pass this info to the EPF core so that the EPF drivers can make use of this info. Link: https://lore.kernel.org/linux-pci/20230717065459.14138-2-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2023-07-13PCI: qcom-ep: Switch MHI bus master clock off during L1SSManivannan Sadhasivam
Currently, as part of the qcom_pcie_perst_deassert() function, instead of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable "val" is re-read. This must be fixed to ensure that the master clock supplied to the MHI bus is correctly gated during L1.1/L1.2 to save power. Thus, replace the line that re-reads "val" with a line that writes the updated value to the register to clear PARF_MSTR_AXI_CLK_EN. [kwilczynski: commit log] Fixes: c457ac029e44 ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS") Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2023-06-26Merge branch 'pci/controller/remove-void-callbacks'Bjorn Helgaas
- Convert platform_device .remove() callbacks to return void instead of a mostly useless int (Uwe Kleine-König) * pci/controller/remove-void-callbacks: PCI: xgene-msi: Convert to platform remove callback returning void PCI: tegra: Convert to platform remove callback returning void PCI: rockchip-host: Convert to platform remove callback returning void PCI: mvebu: Convert to platform remove callback returning void PCI: mt7621: Convert to platform remove callback returning void PCI: mediatek-gen3: Convert to platform remove callback returning void PCI: mediatek: Convert to platform remove callback returning void PCI: iproc: Convert to platform remove callback returning void PCI: hisi-error: Convert to platform remove callback returning void PCI: dwc: Convert to platform remove callback returning void PCI: j721e: Convert to platform remove callback returning void PCI: brcmstb: Convert to platform remove callback returning void PCI: altera-msi: Convert to platform remove callback returning void PCI: altera: Convert to platform remove callback returning void PCI: aardvark: Convert to platform remove callback returning void
2023-06-24PCI: dwc: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Trivially convert the dwc drivers from always returning zero in the remove callback to the void returning variant. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230321193208.366561-7-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Acked-by: Serge Semin <fancer.lancer@gmail.com>
2023-06-23PCI: qcom-ep: Add support for BME notificationManivannan Sadhasivam
Add support to pass BME (Bus Master Enable) notification to Endpoint function driver so that the BME event can be processed by the function. Link: https://lore.kernel.org/r/20230602114756.36586-8-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
2023-06-23PCI: qcom-ep: Add support for Link down notificationManivannan Sadhasivam
Add support to pass Link down notification to Endpoint function driver so that the LINK_DOWN event can be processed by the function. Link: https://lore.kernel.org/r/20230602114756.36586-7-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
2022-10-17PCI: qcom-ep: Setup PHY to work in EP modeDmitry Baryshkov
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being used in the EP mode. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Jingoo Han <jingoohan1@gmail.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Link: https://lore.kernel.org/r/20220927092207.161501-6-dmitry.baryshkov@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-10-05PCI: qcom-ep: Check platform_get_resource_byname() return valueYang Yingliang
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL pointer, which causes a NULL pointer dereference when it is used in qcom_pcie_perst_deassert(). Check the return value to prevent it. Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
2022-10-05PCI: qcom-ep: Add support for SM8450 SoCManivannan Sadhasivam
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller driver. The driver uses the same config as the existing SDX55 chipset, so additional settings are not required. Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-10-05PCI: qcom-ep: Make PERST separation optionalManivannan Sadhasivam
PERST separation is an optional debug feature used to collect the crash dump from the PCIe endpoint devices by the PCIe host when the endpoint crashes. This feature keeps the PCIe link up by separating the PCIe IP block from the SoC reset logic. Make the property optional in the driver. Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-10-05PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe trafficManivannan Sadhasivam
The Master AXI clock can be disabled when it is not used i.e., when there is no traffic on the PCIe bus. This helps to save power during idle state. [bhelgaas: tidy and wrap comment] Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-10-05PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SSManivannan Sadhasivam
During L1SS, gate the Master clock supplied to the MHI bus to save power. Link: https://lore.kernel.org/r/20220914075350.7992-7-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-10-05PCI: qcom-ep: Expose link transition counts via debugfsManivannan Sadhasivam
Qualcomm PCIe controllers have debug registers in the MMIO region that count PCIe link transitions. Expose them over debugfs to userspace to help debug the low power issues. Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-10-05PCI: qcom-ep: Disable IRQs during driver removeManivannan Sadhasivam
Disable the Global and PERST IRQs during driver remove to avoid getting spurious IRQs after resource deallocation. Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-10-03PCI: qcom-ep: Make use of the cached dev pointerManivannan Sadhasivam
In the qcom_pcie_ep_get_resources() function, dev pointer is already cached in a local variable. So let's make use of it instead of getting the dev pointer again from pdev struct. Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>