| Age | Commit message (Collapse) | Author |
|---|
|
It's the last to go in remove. Safe to let devm handle it.
Also move request_irq to probe for clarity. It's removed in _remove not
close.
Use dev_err_probe instead of printk. Handles EPROBE_DEFER automatically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240912024903.6201-3-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows to simplify the code slightly. This is safe to do as free_netdev
gets called last.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240912024903.6201-2-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Display channel info in the RPM map debugfs output.
With this, cat /sys/kernel/debug/cn10k/rvu_pf_rpm_map
would display channel number for each device in addition to
the existing data.
Sample output:
PCI dev RVU PF Func NIX block rpm LMAC CHAN
0002:02:00.0 0x400 NIX0 rpm0 LMAC0 256
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Link: https://patch.msgid.link/20240912161450.164402-3-lcherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-09-11
The first patch is by Uwe Kleine-König targets all CAN platform driver
and switches back the remove function to struct
platform_driver::remove().
A patch by Stefan Mätje fixes the help text of the ESD USB driver.
Jake Hamby's patch masks an unneeded interrupt in the m_can driver.
The last 2 patches target the rockchip_canfd driver. Arnd Bergmann's
patch reworks the delay calculation for the timekeeping worker, a
patch by me fixes the decoding of the error code register.
* tag 'linux-can-next-for-6.12-20240911' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rockchip_canfd: rkcanfd_handle_error_int_reg_ec(): fix decoding of error code register
can: rockchip_canfd: rkcanfd_timestamp_init(): rework delay calculation
can: m_can: m_can_chip_config(): mask timestamp wraparound IRQ
can: usb: Kconfig: Fix list of devices for esd_usb driver
can: Switch back to struct platform_driver::remove()
====================
Link: https://patch.msgid.link/20240912080438.2826895-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return an error if dma_set_mask_and_coherent() fails. Don't return
success.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/f53ed942-5ac2-424b-a1ed-9473c599905e@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-09-12
Kuniyuki Iwashima's patch fixes an incomplete bug fix in the CAN BCM
protocol, which was introduced during v6.11.
A patch by Stefan Mätje removes the unsupported CAN_CTRLMODE_3_SAMPLES
mode for CAN-USB/3-FD devices in the esd_usb driver.
The next patch is by Martin Jocic and enables 64-bit DMA addressing
for the kvaser_pciefd driver.
The last two patches both affect the m_can driver. Jake Hamby's patch
activates NAPI before interrupts are activated, a patch by me moves
the stopping of the clock after the device has been shut down.
* tag 'linux-can-fixes-for-6.11-20240912' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_close(): stop clocks after device has been shut down
can: m_can: enable NAPI before enabling interrupts
can: kvaser_pciefd: Enable 64-bit DMA addressing
can: esd_usb: Remove CAN_CTRLMODE_3_SAMPLES for CAN-USB/3-FD
can: bcm: Clear bo->bcm_proc_read after remove_proc_entry().
====================
Link: https://patch.msgid.link/20240912075804.2825408-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make 'ethtool -S <intf>' output show some per rq/wq statistics that
don't exist in the netdev qstats.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20240912005039.10797-5-neescoba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Report per queue wq/rq statistics in netdev qstats.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20240912005039.10797-4-neescoba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Collect and per rq/wq statistics.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20240912005039.10797-3-neescoba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In enic_ethtool.c there is no need to use static const variables to store
array sizes when a macro can be used instead.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20240912005039.10797-2-neescoba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_VDEVICE() macro and usual pattern for
PCI device ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240913125146.3628751-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enetc driver uses ifdefs when checking whether
CONFIG_FSL_ENETC_PTP_CLOCK is enabled in a number of places. This works
if the driver is built-in but fails if the driver is available as a
kernel module. Replace the instances of ifdef with use of the IS_ENABLED
macro, that will evaluate as true when this feature is built as a kernel
module and follows the kernel's coding style.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240912173742.484549-1-martyn.welch@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver calls netif_napi_set_irq() and then calls netif_napi_add(),
which calls netif_napi_add_weight(). At the end of
netif_napi_add_weight() is a call to netif_napi_set_irq(napi, -1), which
clears the previously set napi->irq value. Fix this by calling
netif_napi_set_irq() after calling netif_napi_add().
This was found when reviewing another patch and I have no way to test
this, but the fix seemed relatively straight forward.
Fixes: bc6107771bb4 ("eth: fbnic: Allocate a netdevice and napi vectors with queues")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20240912174922.10550-1-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
En-Wei reported that traffic breaks if cable is unplugged for more
than 3s and then re-plugged. This was supposed to be fixed by
621735f59064 ("r8169: fix rare issue with broken rx after link-down on
RTL8125"). But apparently this didn't fix the issue for everybody.
The 3s threshold rang a bell, as this is the delay after which ALDPS
kicks in. And indeed disabling ALDPS fixes the issue for this user.
Maybe this fixes the issue in general. In a follow-up step we could
remove the first fix attempt and see whether anybody complains.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Tested-by: En-Wei WU <en-wei.wu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/778b9d86-05c4-4856-be59-cde4487b9e52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "err" is always zero, so the following branch can never be executed:
if (err) {
ndev->stats.rx_dropped++;
kfree_skb(skb);
}
Therefore, the "if" statement can be removed.
Use "ndev->stats.rx_errors" to count "napi_build_skb()" failure
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/20240911135828.378317-1-usama.anjum@collabora.com
Signed-off-by: Qianqiang Liu <qianqiang.liu@163.com>
Link: https://patch.msgid.link/20240913014731.149739-1-qianqiang.liu@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During the introduction of struct bpf_net_context handling for
XDP-redirect, the netkit driver has been missed, which also requires it
because NETKIT_REDIRECT invokes skb_do_redirect() which is accessing the
per-CPU variables. Otherwise we see the following crash:
BUG: kernel NULL pointer dereference, address: 0000000000000038
bpf_redirect()
netkit_xmit()
dev_hard_start_xmit()
Set the bpf_net_context before invoking netkit_xmit() program within the
netkit driver.
Fixes: 401cb7dae813 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20240912155620.1334587-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we support multiple RX queues, enable default priority
to flow mapping so that higher priority packets come on higher
channels (flows).
The Classifier checks for PCP/DSCP priority in the packet and
routes them to the appropriate flow.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Policer registers in the ALE register space are just shadow registers
and use an index field in the policer table control register to read/write
to the actual Polier registers.
Add helper functions to Read and Write to Policer registers.
Also add a helper function to set the thread value to classifier/policer
mapping. Any packet that first matches the classifier will be sent to the
thread (flow) that is set in the classifier to thread mapping table.
If not set then it goes to the default flow.
Default behaviour is to have 8 classifiers to map 8 DSCP/PCP
priorities to N receive threads (flows). N depends on number of
RX channels enabled for the port.
As per the standard [1] User prioritie 1 (Background) and 2 (Spare) have
lower priority than the user priority 0 (default). User priority 1 being
of the lowest priority.
[1] IEEE802.1D-2004, IEEE Standard for Local and metropolitan area networks
Table G-2 - Traffic type acronyms
Table G-3 - Defining traffic types
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds regfileds for Policer registers and Thread mapping/control registers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use regfields for number of ALE Entries and Policers.
The variants that support Policers/Classifiers have the number
of policers encoded in the ALE_STATUS register.
Use that and show the number of Policers in the ALE info message.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Map the entire ALE registerspace using regmap.
Add regfields for Major and Minor Version fields.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
am65-cpsw can support up to 8 queues at Rx.
Use a macro AM65_CPSW_MAX_RX_QUEUES to indicate that.
As there is only one DMA channel for RX traffic, the
8 queues come as 8 flows in that channel.
By default, we will start with 1 flow as defined by the
macro AM65_CPSW_DEFAULT_RX_CHN_FLOWS.
User can change the number of flows by ethtool like so
'ethtool -L ethx rx <N>'
All traffic will still come on flow 0. To get traffic on
different flows the Classifiers will need to be set up.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IB layer provides a common interface to store and get net
devices associated to an IB device port (ib_device_set_netdev()
and ib_device_get_netdev()).
Previously, mlx5_ib stored and managed the associated net devices
internally.
Replace internal net device management in mlx5_ib with
ib_device_set_netdev() when attaching/detaching a net device and
ib_device_get_netdev() when retrieving the net device.
Export ib_device_get_netdev().
For mlx5 representors/PFs/VFs and lag creation we replace the netdev
assignments with the IB set/get netdev functions.
In active-backup mode lag the active slave net device is stored in the
lag itself. To assure the net device stored in a lag bond IB device is
the active slave we implement the following:
- mlx5_core: when modifying the slave of a bond we send the internal driver event
MLX5_DRIVER_EVENT_ACTIVE_BACKUP_LAG_CHANGE_LOWERSTATE.
- mlx5_ib: when catching the event call ib_device_set_netdev()
This patch also ensures the correct IB events are sent in switchdev lag.
While at it, when in multiport eswitch mode, only a single IB device is
created for all ports. The said IB device will receive all netdev events
of its VFs once loaded, thus to avoid overwriting the mapping of PF IB
device to PF netdev, ignore NETDEV_REGISTER events if the ib device has
already been mapped to a netdev.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909173025.30422-6-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When running over new FW that supports the new memory scheme ODP, set
the cap in the FW to signal the FW we are working in the new scheme.
In the memory scheme ODP the per_transport_service capabilities are RO
for the driver so we skip their setting.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-9-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
mlx5e_free_rq previously cleaned resources in an order that was not the
reverse of the resource allocation order in mlx5e_alloc_rq.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When SHAMPO can't identify the protocol/header of a packet, it will
yield a packet that is not split - all the packet is in the data part.
Count this value in packets and bytes.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-15-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new command status MLX5_CMD_STAT_NOT_READY to handle cases
where the firmware is not ready.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20240911201757.1505453-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SFs didn't allow to configure IRQ affinity for its vectors. Allow users
to configure the affinity of the SFs irqs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20240911201757.1505453-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sync reset request is nacked by the driver when PCIe bridge connected to
mlx5 device has HotPlug interrupt enabled. However, when using reset
method of hot reset this check can be skipped as Hotplug is supported on
this reset method.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On device that supports sync reset for firmware activate using hot
reset, the driver queries the required reset method while handling the
sync reset request. If the required reset method is hot reset, the
driver will use pci_reset_bus() to reset the PCI link instead of the
link toggle.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Native capability for some steering engines lacks support for adding an
additional match with the same value to the same flow group. To accommodate
the NO APPEND flag in these scenarios, we include the new rule in the
existing flow table entry (fte) without immediate hardware commitment. When
a request is made to delete the corresponding hardware rule, we then commit
the pending rule to hardware.
Only one pending rule is supported because NO_APPEND is primarily used
during replacement operations. In this scenario, a rule is initially added.
When it needs replacement, the new rule is added with NO_APPEND set. Only
after the insertion of the new rule is the original rule deleted.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce a dedicated structure to encapsulate flow context, actions,
destination count, and modification mask. This refactoring lays the
groundwork for forthcoming patches that will integrate the NO APPEND
software logic. Future modifications should focus solely on these
specific fields.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Counter is in struct fte, remove it.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Downstream patches will need this as we might not want to reset
it when a pending rule is connected to the FTE.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As preparation for HW Steering support, where the function
get_root_namespace() is needed to get root FDB, make it an API function
and rename it to mlx5_get_root_namespace().
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20240911201757.1505453-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As preparation for HW steering support in fs core level, move SW
steering helper function that can be reused by HW steering to fs_cmd.h.
The function mlx5_fs_cmd_is_fw_term_table() checks if a flow table is a
flow steering termination table and so should be handled by FW steering.
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixed all the '-ret' returns in error flow of functions to 'ret',
as the internal functions are already returning negative error values
(e.g. -EINVAL)
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changed all the functions comments to adhere with kernel-doc formatting.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240911201757.1505453-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240911094445.1922476-4-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: bbb96dc7fa1a ("enetc: Factor out the traffic start/stop procedures")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240911094445.1922476-3-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240911094445.1922476-2-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both bareudp_xmit_skb() and bareudp6_xmit_skb() read their skb's inner
IP header to get its ECN value (with ip_tunnel_ecn_encap()). Therefore
we need to ensure that the inner IP header is part of the skb's linear
data.
Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/267328222f0a11519c6de04c640a4f87a38ea9ed.1726046181.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Bareudp reads the inner IP header to get the ECN value. Therefore, it
needs to ensure that it's part of the skb's linear data.
This is similar to the vxlan and geneve fixes for that same problem:
* commit f7789419137b ("vxlan: Pull inner IP header in vxlan_rcv().")
* commit 1ca1ba465e55 ("geneve: make sure to pull inner header in
geneve_rx()")
Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/5205940067c40218a70fbb888080466b2fc288db.1726046181.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-09-11
We've added 12 non-merge commits during the last 16 day(s) which contain
a total of 20 files changed, 228 insertions(+), 30 deletions(-).
There's a minor merge conflict in drivers/net/netkit.c:
00d066a4d4ed ("netdev_features: convert NETIF_F_LLTX to dev->lltx")
d96608794889 ("netkit: Disable netpoll support")
The main changes are:
1) Enable bpf_dynptr_from_skb for tp_btf such that this can be used
to easily parse skbs in BPF programs attached to tracepoints,
from Philo Lu.
2) Add a cond_resched() point in BPF's sock_hash_free() as there have
been several syzbot soft lockup reports recently, from Eric Dumazet.
3) Fix xsk_buff_can_alloc() to account for queue_empty_descs which
got noticed when zero copy ice driver started to use it,
from Maciej Fijalkowski.
4) Move the xdp:xdp_cpumap_kthread tracepoint before cpumap pushes skbs
up via netif_receive_skb_list() to better measure latencies,
from Daniel Xu.
5) Follow-up to disable netpoll support from netkit, from Daniel Borkmann.
6) Improve xsk selftests to not assume a fixed MAX_SKB_FRAGS of 17 but
instead gather the actual value via /proc/sys/net/core/max_skb_frags,
also from Maciej Fijalkowski.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
sock_map: Add a cond_resched() in sock_hash_free()
selftests/bpf: Expand skb dynptr selftests for tp_btf
bpf: Allow bpf_dynptr_from_skb() for tp_btf
tcp: Use skb__nullable in trace_tcp_send_reset
selftests/bpf: Add test for __nullable suffix in tp_btf
bpf: Support __nullable argument suffix for tp_btf
bpf, cpumap: Move xdp:xdp_cpumap_kthread tracepoint before rcv
selftests/xsk: Read current MAX_SKB_FRAGS from sysctl knob
xsk: Bump xsk_queue::queue_empty_descs in xp_can_alloc()
tcp_bpf: Remove an unused parameter for bpf_tcp_ingress()
bpf, sockmap: Correct spelling skmsg.c
netkit: Disable netpoll support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://patch.msgid.link/20240911211525.13834-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ENA currently supports the following customer metrics:
- `bw_in_allowance_exceeded`
- `bw_out_allowance_exceeded`
- `conntrack_allowance_exceeded`
- `linklocal_allowance_exceeded`
- `pps_allowance_exceeded`
This patch adds a new metric named:
`conntrack_allowance_available`.
Information about these metrics is available in [1].
In addition, the interface between the driver and the
device has been upgraded to allow more flexibility and
expendability to additional metrics in the future.
[1]: https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/monitoring-network-performance-ena.html#network-performance-metrics
Signed-off-by: Ron Beider <rbeider@amazon.com>
Signed-off-by: Shahar Itzko <itzko@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://patch.msgid.link/20240909084704.13856-3-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ENA Express metrics, called `ena_srd` are exposed to
customers via `ethtool`.
The metrics allow customers to check the configuration
(mode), tx/rx counters as well as resource utilization.
The documentation is also updated to provide a general
explanation about ENA Express as well as links for further
information about metrics and configurations.
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://patch.msgid.link/20240909084704.13856-2-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb227 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb04 ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If an interrupt (RX-complete or error flag) is set when bringing up
the CAN device, e.g. due to CAN bus traffic before initializing the
device, when m_can_start() is called and interrupts are enabled,
m_can_isr() is called immediately, which disables all CAN interrupts
and calls napi_schedule().
Because napi_enable() isn't called until later in m_can_open(), the
call to napi_schedule() never schedules the m_can_poll() callback and
the device is left with interrupts disabled and can't receive any CAN
packets until rebooted.
This can be verified by running "cansend" from another device before
setting the bitrate and calling "ip link set up can0" on the test
device. Adding debug lines to m_can_isr() shows it's called with flags
(IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts()
and napi_schedule(), and then m_can_poll() is never called.
Move the call to napi_enable() above the call to m_can_start() to
enable any initial interrupt flags to be handled by m_can_poll() so
that interrupts are reenabled. Add a call to napi_disable() in the
error handling section of m_can_open(), to handle the case where later
functions return errors.
Also, in m_can_close(), move the call to napi_disable() below the call
to m_can_stop() to ensure all interrupts are handled when bringing
down the device. This race condition is much less likely to occur.
Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to
any SoC with a Bosch M_CAN controller.
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enabling 64-bit addressing for DMA buffers will prevent issues
on some memory constrained platforms like e.g. Raspberry Pi 5,
where the driver won't load because it cannot allocate enough
continuous memory in the default 32-bit memory address range.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://patch.msgid.link/d7340f78e3db305bfeeb8229d2dd1c9077e10b92.1725875278.git.martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
