| Age | Commit message (Collapse) | Author |
|---|
|
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650e8 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ravb_phy_start() may fail. If that happens, the TX queues will remain
started. Thus, move the netif_tx_start_all_queues() after PHY is
successfully initialized.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
registers
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada8d ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464a0 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since pci_free_irq_vectors() set pdev->msix_enabled as 0 in the
calling of pci_msix_shutdown(), wx->msix_entries is never freed.
Reordering the lines to fix the memory leak.
Cc: stable@vger.kernel.org
Fixes: 3f703186113f ("net: libwx: Add irq flow functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20231128095928.1083292-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().
Fixes: abe5fc42f9ce ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The original change results in a deadlock if jumbo mtu mode is used.
Reason is that the phydev lock is held when rtl_reset_work() is called
here, and rtl_jumbo_config() calls phy_start_aneg() which also tries
to acquire the phydev lock. Fix this by calling rtl_reset_work()
asynchronously.
Fixes: 621735f59064 ("r8169: fix rare issue with broken rx after link-down on RTL8125")
Reported-by: Ian Chen <free122448@hotmail.com>
Tested-by: Ian Chen <free122448@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/caf6a487-ef8c-4570-88f9-f47a659faf33@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.
Fixes: 68fbff68dbea ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.
Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.
The patch moves the break to the
beginning of the loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8e095b3b370 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.
This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.
Fixes: 50f826999a80 ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f19e ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.
Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This .ndo_start_xmit() function should return netdev_tx_t value,
not -ENOMEM. So, fix it.
Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The type of ret in rswitch_start_xmit() should be netdev_tx_t. So,
fix it.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a typo, the code checked the RX checksum feature in the TX path.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a65 ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit d938a8cca88a ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca88a ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
queue than its PF
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit efa5f1311c4998e9e6317c52bc5ee93b3a0f36df.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During 'ifconfig <netdev> down' one RSS memory was not getting freed.
This patch fixes the same.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device uses a custom subsystem vendor ID, the function
wx_sw_init() returns before the memory of 'wx->mac_table' is allocated.
The null pointer will causes the kernel panic.
Fixes: 79625f45ca73 ("net: wangxun: Move MAC address handling to libwx")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
representors
Treat the operation as an error case when the return value is equivalent to
the size of the name buffer. Failed to write null terminator to the name
buffer, making the string malformed and should not be used. Provide a
string with only the firmware version when forming the string with the
board id fails. This logic for representors is identical to normal flow
with ethtool.
Without check, will trigger -Wformat-truncation with W=1.
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_rep_get_drvinfo':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:78:31: warning: '%.16s' directive output may be truncated writing up to 16 bytes into a region of size between 13 and 22 [-Wformat-truncation=]
78 | "%d.%d.%04d (%.16s)",
| ^~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:77:9: note: 'snprintf' output between 12 and 37 bytes into a destination of size 32
77 | snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
78 | "%d.%d.%04d (%.16s)",
| ~~~~~~~~~~~~~~~~~~~~~
79 | fw_rev_maj(mdev), fw_rev_min(mdev),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
80 | fw_rev_sub(mdev), mdev->board_id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: cf83c8fdcd47 ("net/mlx5e: Add missing ethtool driver info for representors")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732c
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Treat the operation as an error case when the return value is equivalent to
the size of the name buffer. Failed to write null terminator to the name
buffer, making the string malformed and should not be used. Provide a
string with only the firmware version when forming the string with the
board id fails.
Without check, will trigger -Wformat-truncation with W=1.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c: In function 'mlx5e_ethtool_get_drvinfo':
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:49:31: warning: '%.16s' directive output may be truncated writing up to 16 bytes into a region of size between 13 and 22 [-Wformat-truncation=]
49 | "%d.%d.%04d (%.16s)",
| ^~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:48:9: note: 'snprintf' output between 12 and 37 bytes into a destination of size 32
48 | snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
49 | "%d.%d.%04d (%.16s)",
| ~~~~~~~~~~~~~~~~~~~~~
50 | fw_rev_maj(mdev), fw_rev_min(mdev), fw_rev_sub(mdev),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
51 | mdev->board_id);
| ~~~~~~~~~~~~~~~
Fixes: 84e11edb71de ("net/mlx5e: Show board id in ethtool driver information")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732c
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
icosq_str size is unnecessarily too long, and it causes a build warning
-Wformat-truncation with W=1. Looking closely, It doesn't need to be 255B,
hence this patch reduces the size to 32B which should be more than enough
to host the string: "ICOSQ: 0x%x, ".
While here, add a missing space in the formatted string.
This fixes the following build warning:
$ KCFLAGS='-Wall -Werror'
$ make O=/tmp/kbuild/linux W=1 -s -j12 drivers/net/ethernet/mellanox/mlx5/core/
drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c: In function 'mlx5e_reporter_rx_timeout':
drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c:718:56:
error: ', CQ: 0x' directive output may be truncated writing 8 bytes into a region of size between 0 and 255 [-Werror=format-truncation=]
718 | "RX timeout on channel: %d, %sRQ: 0x%x, CQ: 0x%x",
| ^~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en/reporter_rx.c:717:9: note: 'snprintf' output between 43 and 322 bytes into a destination of size 288
717 | snprintf(err_str, sizeof(err_str),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
718 | "RX timeout on channel: %d, %sRQ: 0x%x, CQ: 0x%x",
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
719 | rq->ix, icosq_str, rq->rqn, rq->cq.mcq.cqn);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 521f31af004a ("net/mlx5e: Allow RQ outside of channel context")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732c
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Without increased buffer size, will trigger -Wformat-truncation with W=1
for the snprintf operation writing to the buffer.
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c: In function 'mlx5_irq_alloc':
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c:296:7: error: '@pci:' directive output may be truncated writing 5 bytes into a region of size between 1 and 32 [-Werror=format-truncation=]
296 | "%s@pci:%s", name, pci_name(dev->pdev));
| ^~~~~
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c:295:2: note: 'snprintf' output 6 or more bytes (assuming 37) into a destination of size 32
295 | snprintf(irq->name, MLX5_MAX_IRQ_NAME,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
296 | "%s@pci:%s", name, pci_name(dev->pdev));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: ada9f5d00797 ("IB/mlx5: Fix eq names to display nicely in /proc/interrupts")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732c
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, mlx5e_ptp_poll_ts_cq would update the device doorbell with the
incremented consumer index after the relevant software counters in the
kernel were updated. In the mlx5e_sq_xmit_wqe context, this would lead to
either overrunning the device CQ or exceeding the expected software buffer
size in the device CQ if the device CQ size was greater than the software
buffer size. Update the relevant software counter only after updating the
device CQ consumer index in the port timestamping napi_poll context.
Log:
mlx5_core 0000:08:00.0: cq_err_event_notifier:517:(pid 0): CQ error on CQN 0x487, syndrome 0x1
mlx5_core 0000:08:00.0 eth2: mlx5e_cq_error_event: cqn=0x000487 event=0x04
Fixes: 1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure the skb is available in metadata mapping to skbs before tracking the
metadata index for detecting undelivered CQEs. If the metadata index is put
in the tracking list before putting the skb in the map, the metadata index
might be used for detecting undelivered CQEs before the relevant skb is
available in the map, which can lead to a null-ptr-deref.
Log:
general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
CPU: 0 PID: 1243 Comm: kworker/0:2 Not tainted 6.6.0-rc4+ #108
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: events mlx5e_rx_dim_work [mlx5_core]
RIP: 0010:mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core]
Code: 8c 24 38 cc ff ff 4c 8d 3c c1 4c 89 f9 48 c1 e9 03 42 80 3c 31 00 0f 85 97 0f 00 00 4d 8b 3f 49 8d 7f 28 48 89 f9 48 c1 e9 03 <42> 80 3c 31 00 0f 85 8b 0f 00 00 49 8b 47 28 48 85 c0 0f 84 05 07
RSP: 0018:ffff8884d3c09c88 EFLAGS: 00010206
RAX: 0000000000000069 RBX: ffff8881160349d8 RCX: 0000000000000005
RDX: ffffed10218f48cf RSI: 0000000000000004 RDI: 0000000000000028
RBP: ffff888122707700 R08: 0000000000000001 R09: ffffed109a781383
R10: 0000000000000003 R11: 0000000000000003 R12: ffff88810c7a7a40
R13: ffff888122707700 R14: dffffc0000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8884d3c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4f878dd6e0 CR3: 000000014d108002 CR4: 0000000000370eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? die_addr+0x3c/0xa0
? exc_general_protection+0x144/0x210
? asm_exc_general_protection+0x22/0x30
? mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core]
? mlx5e_ptp_napi_poll+0x8f6/0x2290 [mlx5_core]
__napi_poll.constprop.0+0xa4/0x580
net_rx_action+0x460/0xb80
? _raw_spin_unlock_irqrestore+0x32/0x60
? __napi_poll.constprop.0+0x580/0x580
? tasklet_action_common.isra.0+0x2ef/0x760
__do_softirq+0x26c/0x827
irq_exit_rcu+0xc2/0x100
common_interrupt+0x7f/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:__kmem_cache_alloc_node+0xb/0x330
Code: 41 5d 41 5e 41 5f c3 8b 44 24 14 8b 4c 24 10 09 c8 eb d5 e8 b7 43 ca 01 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 57 <41> 56 41 89 d6 41 55 41 89 f5 41 54 49 89 fc 53 48 83 e4 f0 48 83
RSP: 0018:ffff88812c4079c0 EFLAGS: 00000246
RAX: 1ffffffff083c7fe RBX: ffff888100042dc0 RCX: 0000000000000218
RDX: 00000000ffffffff RSI: 0000000000000dc0 RDI: ffff888100042dc0
RBP: ffff88812c4079c8 R08: ffffffffa0289f96 R09: ffffed1025880ea9
R10: ffff888138839f80 R11: 0000000000000002 R12: 0000000000000dc0
R13: 0000000000000100 R14: 000000000000008c R15: ffff8881271fc450
? cmd_exec+0x796/0x2200 [mlx5_core]
kmalloc_trace+0x26/0xc0
cmd_exec+0x796/0x2200 [mlx5_core]
mlx5_cmd_do+0x22/0xc0 [mlx5_core]
mlx5_cmd_exec+0x17/0x30 [mlx5_core]
mlx5_core_modify_cq_moderation+0x139/0x1b0 [mlx5_core]
? mlx5_add_cq_to_tasklet+0x280/0x280 [mlx5_core]
? lockdep_set_lock_cmp_fn+0x190/0x190
? process_one_work+0x659/0x1220
mlx5e_rx_dim_work+0x9d/0x100 [mlx5_core]
process_one_work+0x730/0x1220
? lockdep_hardirqs_on_prepare+0x400/0x400
? max_active_store+0xf0/0xf0
? assign_work+0x168/0x240
worker_thread+0x70f/0x12d0
? __kthread_parkme+0xd1/0x1d0
? process_one_work+0x1220/0x1220
kthread+0x2d9/0x3b0
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x2d/0x70
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
Modules linked in: xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_ib ib_uverbs ib_core zram zsmalloc mlx5_core fuse
---[ end trace 0000000000000000 ]---
Fixes: 3178308ad4ca ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlx5e_sq_xmit_wqe
When SQ is a port timestamping SQ for PTP, do not access tx flags of skb
after free-ing the skb. Free the skb only after all references that depend
on it have been handled in the dropped WQE path.
Fixes: 3178308ad4ca ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As IPSec packet offload in switchdev mode is not supported with LAG,
it's unnecessary to modify those sent-to-vport rules to the peer eswitch.
Fixes: c6c2bf5db4ea ("net/mlx5e: Support IPsec packet offload for TX in switchdev mode")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Referenced commit addressed endianness issue in mlx5 pedit implementation
in ad hoc manner instead of systematically treating integer values
according to their types which left pedit fields of sizes not equal to 4
and where the bytes being modified are not least significant ones broken on
big endian machines since wrong bits will be consumed during parsing which
leads to following example error when applying pedit to source and
destination MAC addresses:
[Wed Oct 18 12:52:42 2023] mlx5_core 0001:00:00.1 p1v3_r: attempt to offload an unsupported field (cmd 0)
[Wed Oct 18 12:52:42 2023] mask: 00000000330c5b68: 00 00 00 00 ff ff 00 00 00 00 ff ff 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 0000000017d22fd9: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 000000008186d717: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 0000000029eb6149: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 000000007ed103e4: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 00000000db8101a6: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
[Wed Oct 18 12:52:42 2023] mask: 00000000ec3c08a9: 00 00 00 00 00 00 00 00 00 00 00 00 ............
Treat masks and values of pedit and filter match as network byte order,
refactor pointers to them to void pointers instead of confusing u32
pointers and only cast to pointer-to-integer when reading a value from
them. Treat pedit mlx5_fields->field_mask as host byte order according to
its type u32, change the constants in fields array accordingly.
Fixes: 82198d8bcdef ("net/mlx5e: Fix endianness when calculating pedit mask first bit")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow up to the previous patch to fix the same issue for
mlx5e_tc_tun_update_header_ipv4{6} when mlx5_packet_reformat_alloc()
fails.
When mlx5_packet_reformat_alloc() fails, the encap_header allocated in
mlx5e_tc_tun_update_header_ipv4{6} will be released within it. However,
e->encap_header is already set to the previously freed encap_header
before mlx5_packet_reformat_alloc(). As a result, the later
mlx5e_encap_put() will free e->encap_header again, causing a double free
issue.
mlx5e_encap_put()
--> mlx5e_encap_dealloc()
--> kfree(e->encap_header)
This patch fix it by not setting e->encap_header until
mlx5_packet_reformat_alloc() success.
Fixes: a54e20b4fcae ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When mlx5_packet_reformat_alloc() fails, the encap_header allocated in
mlx5e_tc_tun_create_header_ipv4{6} will be released within it. However,
e->encap_header is already set to the previously freed encap_header
before mlx5_packet_reformat_alloc(). As a result, the later
mlx5e_encap_put() will free e->encap_header again, causing a double free
issue.
mlx5e_encap_put()
--> mlx5e_encap_dealloc()
--> kfree(e->encap_header)
This happens when cmd: MLX5_CMD_OP_ALLOC_PACKET_REFORMAT_CONTEXT fail.
This patch fix it by not setting e->encap_header until
mlx5_packet_reformat_alloc() success.
Fixes: d589e785baf5e ("net/mlx5e: Allow concurrent creation of encap entries")
Reported-by: Cruz Zhao <cruzzhao@linux.alibaba.com>
Reported-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running a phase adjustment operation, the free running clock should
not be modified at all. The phase control keyword is intended to trigger an
internal servo on the device that will converge to the provided delta. A
free running counter cannot implement phase adjustment.
Fixes: 8e11a68e2e8a ("net/mlx5: Add adjphase function to support hardware-only offset control")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current check isn't aware of old devices that don't have the
relevant FW capability. This patch allows multi destination FTE
in old cards, as it was before this check.
Fixes: f6f46e7173cb ("net/mlx5: DR, Add check for multi destination FTE")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Each EQ table maintains a cpumask of the already used CPUs that are mapped
to IRQs to ensure that each IRQ gets mapped to a unique CPU.
However, on IRQ release, the said cpumask is not updated by clearing the
CPU from the mask to allow future IRQ request, causing the following
error when a SF is reloaded after it has utilized all CPUs for its IRQs:
mlx5_irq_affinity_request:135:(pid 306010): Didn't find a matching IRQ.
err = -28
Thus, when releasing an IRQ, clear its mapped CPU from the used CPUs
mask, to prevent the case described above.
While at it, move the used cpumask update to the EQ layer as it is more
fitting and preserves symmetricity of the IRQ request/release API.
Fixes: a1772de78d73 ("net/mlx5: Refactor completion IRQ request/release API")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 95c337cce0e11d06a715da73e6796ade9216637f.
The revert is required due to the suspicion it cause some tests
fail and will be moved to further investigation.
Fixes: 95c337cce0e1 ("net/mlx5: DR, Supporting inline WQE when possible")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Netpoll will explicilty pass the polling call with a budget of 0 to
indicate it's clearing the Tx path only. For the gve_rx_poll and
gve_xdp_poll, they were mistakenly taking the 0 budget as the indication
to do all the work. Add check to avoid the rx path and xdp path being
called when budget is 0. And also avoid napi_complete_done being called
when budget is 0 for netpoll.
Fixes: f5cedc84a30d ("gve: Add transmit and receive support")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Link: https://lore.kernel.org/r/20231114004144.2022268-1-ziweixiao@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-13 (ice)
This series contains updates to ice driver only.
Arkadiusz ensures the device is initialized with valid lock status
value. He also removes range checking of dpll priority to allow firmware
to process the request; supported values are firmware dependent.
Finally, he removes setting of can change capability for pins that
cannot be changed.
Dan restores ability to load a package which doesn't contain a signature
segment.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix DDP package download for packages without signature segment
ice: dpll: fix output pin capabilities
ice: dpll: fix check for dpll input priority range
ice: dpll: fix initial lock status of dpll
====================
Link: https://lore.kernel.org/r/20231113230551.548489-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
