| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 881d0327db37ad917a367c77aff1afa1ee41e0a9 ]
Note: This is a verified backported patch for stable 4.4 kernel, and it
could also be applied to 4.3/4.2/4.1/3.18/3.16
There is a problem with alx devices, that the network link will be
lost in 1-5 minutes after the device is up.
>From debugging without datasheet, we found the error always
happen when the DMA RX address is set to 0x....fc0, which is very
likely to be a HW/silicon problem.
This patch will apply rx skb with 64 bytes longer space, and if the
allocated skb has a 0x...fc0 address, it will use skb_resever(skb, 64)
to advance the address, so that the RX overflow can be avoided.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c0795bf64cba4d1b796fdc5b74b33772841ed1bb ]
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec810 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f43bfaeddc79effbf3d0fcb53ca477cca66f3db8 ]
atl2 includes NETIF_F_SG in hw_features even though it has no support
for non-linear skbs. This bug was originally harmless since the
driver does not claim to implement checksum offload and that used to
be a requirement for SG.
Now that SG and checksum offload are independent features, if you
explicitly enable SG *and* use one of the rare protocols that can use
SG without checkusm offload, this potentially leaks sensitive
information (before you notice that it just isn't working). Therefore
this obscure bug has been designated CVE-2016-2117.
Reported-by: Justin Yackoski <jyackoski@crypto-nite.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: ec5f06156423 ("net: Kill link between CSUM and SG features.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81422e672f8181d7ad1ee6c60c723aac649f538f upstream.
According to Documentation/power/devices.txt
The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.
Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.
And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0772a99b818079e628a1da122ac7ee023faed83e upstream.
Otherwise it might be back on resume right after going to suspend in
some hardware.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c9a266afefe137bff06bbe0fc48b4d3b3cb348c ]
When running small packets [length < 256 bytes] traffic, packets were
being dropped due to invalid data in those packets which were
delivered by the driver upto the stack. Using pci_dma_sync_single_for_cpu
ensures copying latest and updated data into skb from the receive buffer.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c1b7fca65070bfadca94dd53a4e6b71cd4f69715 ]
In a low memory situation, if netdev_alloc_skb() fails on a first RX ring
loop iteration in sh_eth_ring_format(), 'rxdesc' is still NULL. Avoid
kernel oops by adding the 'rxdesc' check after the loop.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ee50c130c82175eaa0820c96b6d3763928af2241 ]
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad6afbe9578d1fa26680faf78c846bd8c00d1d6e upstream.
The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.
Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.
This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick Schaaf <netdev@bof.de>
Tested-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 248be83dcb3feb3f6332eb3d010a016402138484 ]
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2a3771ae8aca879c32336c76ad05a017629bae2 ]
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2502d0ef272da7058ef303b849a2c8dc324c2e2e upstream.
The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.
However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.
This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e6dbe1eb2db0d7a14991c06278dd3030c45fb825 ]
priv->hwts_*_en indicate if timestamping is enabled/disabled at run
time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp
indicates HW is support for PTPv1/PTPv2.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c02b05011fadf8e409e41910217ca689f2fc9d91 ]
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249ae
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d6f ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d20a16062e771b6e26b843c0cde3b17c1146e00 upstream.
drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'. Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ade4dc3e616e33c80d7e62855fe1b6f9895bc7c3 ]
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1c1bf34951e8d17941bf708d1901c47e81b15d55 ]
The port-change event processing in procedure mlx4_eq_int() uses "slave"
as the vf_oper array index. Since the value of "slave" is the PF function
index, the result is that the PF link state is used for deciding to
propagate the event for all the VFs. The VF link state should be used,
so the VF function index should be used here.
Fixes: 948e306d7d64 ('net/mlx4: Add VF link state support')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1590670ce069eefeb93916391a67643e6ad1630 upstream.
Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:
[1] On driver probe underlying memory allocated with
dma_alloc_coherent() might not be zeroed and so
it will be filled with garbage.
[2] During driver operation some bits could be set by SD/MMC
controller (for example error flags etc).
And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.
This change addresses both items above with:
[1] Use of dma_zalloc_coherent() instead of simple
dma_alloc_coherent() to make sure allocated memory is
zeroed. That shouldn't affect performance because
this allocation only happens once on driver probe.
[2] Do explicit zeroing of both "des0" and "des1" fields
of all buffer descriptors during initialization of
DMA transfer.
And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3d11fe08ccc9bff174fc958722b5661f0932486 upstream.
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf493 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4f2dacbf2a5045e34b98a35d9a3857800f25a7b upstream.
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0ccc5 ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08e8331654d1d7b2c58045e549005bc356aa7810 upstream.
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
[...]
Call Trace:
[<ffffffff81195445>] put_page+0x55/0x60
[<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
[<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
[<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
[<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
[<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
[<ffffffff81647050>] dev_set_mtu+0xa0/0x140
[<ffffffff81664218>] do_setlink+0x218/0xac0
[<ffffffff814459e9>] ? nla_parse+0xb9/0x120
[<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
[<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
[<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260
By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers. The allocator is set back to a sane value in
e1000_configure_rx.
Fixes: edbbb3ca1077 ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts. For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e5eda89d97ec256ba14e7e861387cc0468259c18 ]
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0ccc5 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87f966d97b89774162df04d2106c6350c8fe4cb3 upstream.
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da293700568ed3d96fcf062ac15d7d7c41377f11 upstream.
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 24e579c8898aa641ede3149234906982290934e5 ]
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6088beef3f7517717bd21d90b379714dd0837079 ]
NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.
If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02a54164c52ed6eca3089a0d402170fbf34d6cf5 upstream.
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation)
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25906052d953d3fbdb7e19480b9de5e6bb949f3f upstream.
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ce67a38f799d1fb332f672b117efbadedaa5352 upstream.
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17e96834fd35997ca7cdfbf15413bcd5a36ad448 ]
Hardware always provides compliment of IP pseudo checksum. Stack expects
whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set.
This causes checksum error in nf & ovs.
kernel: qg-19546f09-f2: hw csum failure
kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1
kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014
kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b
kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0
kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00
kernel: Call Trace:
kernel: <IRQ> [<ffffffff815e237b>] dump_stack+0x19/0x1b
kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40
kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70
kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20
kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100
kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4]
kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0
kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch]
kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack]
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4]
kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380
Hardware verifies IP & tcp/udp header checksum but does not provide payload
checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet.
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Stefan Assmann <sassmann@redhat.com>
Reported-by: Sunil Choudhary <schoudha@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7a05dc64e2e4c611d89007b125b20c0d2a4d31a5 ]
Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered
wrong alx_poll() behavior.
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Also, in case of TX pressure, we still have to dequeue received
packets : alx_clean_rx_irq() has to be called even if
alx_clean_tx_irq(alx) returns false, otherwise device is half duplex.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Reported-by: Oded Gabbay <oded.gabbay@amd.com>
Bisected-by: Oded Gabbay <oded.gabbay@amd.com>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 05b0aa579397b734f127af58e401a30784a1e315 ]
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Please queue for -stable.
Reported-by: Nils Holland <nholland@tisys.org>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aec653c43b0c55667355e26d7de1236bda9fb4e3 upstream.
Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f478b41033606d325e420df693162e2524c2b94 ]
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ]
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ]
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a620a6bc1c94c22d6c312892be1e0ae171523125 ]
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d0aedcd4f14a22e23b313f42b7e6e6ebfc0fbc31 ]
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ccf899a27c08038db91765ff12bb0380dcd85887 ]
With commit be9dad1f9f26604fb ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9026968abe7ad102f4ac5c6d96d733643f75399c ]
This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d3083ee36b51e425b6abd76778a2046906b0fd3 ]
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
