| Age | Commit message (Collapse) | Author |
|---|
|
After the conversion to use the auxiliary bus, the custom device
management is not needed anymore and can be deleted.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the auxiliary bus to perform device management of the infiniband
part of the mlx4 driver.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the auxiliary bus to perform device management of the ethernet part
of the mlx4 driver.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an auxiliary virtual bus to model the mlx4 driver structure. The
code is added along the current custom device management logic.
Subsequent patches switch mlx4_en and mlx4_ib to the auxiliary bus and
the old interface is then removed.
Structure mlx4_priv gains a new adev dynamic array to keep track of its
auxiliary devices. Access to the array is protected by the global
mlx4_intf mutex.
Functions mlx4_register_device() and mlx4_unregister_device() are
updated to expose auxiliary devices on the bus in order to load mlx4_en
and/or mlx4_ib. Functions mlx4_register_auxiliary_driver() and
mlx4_unregister_auxiliary_driver() are added to substitute
mlx4_register_interface() and mlx4_unregister_interface(), respectively.
Function mlx4_do_bond() is adjusted to walk over the adev array and
re-adds a specific auxiliary device if its driver sets the
MLX4_INTFF_BONDING flag.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlx4_core driver has a logic that allows a sub-driver to set the
MLX4_INTFF_BONDING flag which then causes that function mlx4_do_bond()
asks the sub-driver to fully re-probe a device when its bonding
configuration changes.
Performing this operation is disallowed in mlx4_register_interface()
when it is detected that any mlx4 device is multifunction (SRIOV). The
code then resets MLX4_INTFF_BONDING in the driver flags.
Move this check directly into mlx4_do_bond(). It provides a better
separation as mlx4_core no longer directly modifies the sub-driver flags
and it will allow to get rid of explicitly keeping track of all mlx4
devices by the intf.c code when it is switched to an auxiliary bus.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlx4_interface.activate callback was introduced in commit
79857cd31fe7 ("net/mlx4: Postpone the registration of net_device"). It
dealt with a situation when a netdev notifier received a NETDEV_REGISTER
event for a new net_device created by mlx4_en but the same device was
not yet visible to mlx4_get_protocol_dev(). The callback can be removed
now that mlx4_get_protocol_dev() is gone.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a notifier to implement mlx4_dispatch_event() in preparation to
switch mlx4_en and mlx4_ib to be an auxiliary device.
A problem is that if the mlx4_interface.event callback was replaced with
something as mlx4_adrv.event then the implementation of
mlx4_dispatch_event() would need to acquire a lock on a given device
before executing this callback. That is necessary because otherwise
there is no guarantee that the associated driver cannot get unbound when
the callback is running. However, taking this lock is not possible
because mlx4_dispatch_event() can be invoked from the hardirq context.
Using an atomic notifier allows the driver to accurately record when it
wants to receive these events and solves this problem.
A handler registration is done by both mlx4_en and mlx4_ib at the end of
their mlx4_interface.add callback. This matches the current situation
when mlx4_add_device() would enable events for a given device
immediately after this callback, by adding the device on the
mlx4_priv.list.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function mlx4_dispatch_event() takes an 'unsigned long' as its event
parameter. The actual value is none (MLX4_DEV_EVENT_CATASTROPHIC_ERROR),
a pointer to mlx4_eqe (MLX4_DEV_EVENT_PORT_MGMT_CHANGE), or a 32-bit
integer (remaining events).
In preparation to switch mlx4_en and mlx4_ib to be an auxiliary device,
the mlx4_interface.event callback is replaced with a notifier and
function mlx4_dispatch_event() gets updated to invoke
atomic_notifier_call_chain(). This requires forwarding the input 'param'
value from the former function to the latter. A problem is that the
notifier call takes 'void *' as its 'param' value, compared to
'unsigned long' used by mlx4_dispatch_event(). Re-passing the value
would need either punning it to 'void *' or passing down the address of
the input 'param'. Both approaches create a number of unnecessary casts.
Change instead the input 'param' of mlx4_dispatch_event() from
'unsigned long' to 'void *'. A mlx4_eqe pointer can be passed directly,
callers using an int value are adjusted to pass its address.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the mlx4 driver interface by removing mlx4_get_protocol_dev()
and the associated mlx4_interface.get_dev callbacks. This is done in
preparation to use an auxiliary bus to model the mlx4 driver structure.
The change is motivated by the following situation:
* The mlx4_en interface is being initialized by mlx4_en_add() and
mlx4_en_activate().
* The latter activate function calls mlx4_en_init_netdev() ->
register_netdev() to register a new net_device.
* A netdev event NETDEV_REGISTER is raised for the device.
* The netdev notififier mlx4_ib_netdev_event() is called and it invokes
mlx4_ib_scan_netdevs() -> mlx4_get_protocol_dev() ->
mlx4_en_get_netdev() [via mlx4_interface.get_dev].
This chain creates a problem when mlx4_en gets switched to be an
auxiliary driver. It contains two device calls which would both need to
take a respective device lock.
Avoid this situation by updating mlx4_ib_scan_netdevs() to no longer
call mlx4_get_protocol_dev() but instead to utilize the information
passed in net_device.parent and net_device.dev_port. This data is
sufficient to determine that an updated port is one that the mlx4_ib
driver should take care of and to keep mlx4_ib_dev.iboe.netdevs up to
date.
Following that, update mlx4_ib_get_netdev() to also not call
mlx4_get_protocol_dev() and instead scan all current netdevs to find
find a matching one. Note that mlx4_ib_get_netdev() is called early from
ib_register_device() and cannot use data tracked in
mlx4_ib_dev.iboe.netdevs which is not at that point yet set.
Finally, remove function mlx4_get_protocol_dev() and the
mlx4_interface.get_dev callbacks (only mlx4_en_get_netdev()) as they
became unused.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel coding style is to treat sizeof as a function
(ie. with parenthesis) not as an operator.
Also use kcalloc and kmalloc_array
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlx4 driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
The result is that the VF driver on the VM will experience a command
timeout during the shutdown process when the Hypervisor does not deliver
a command-completion event to the VM.
To avoid FW command timeouts on the VM when the driver's shutdown method
is invoked, we detect the absence of the VF's comm channel at the very
start of the shutdown process. If the comm-channel has already been
disabled, we cause all FW commands during the device shutdown process to
immediately return success (and thus avoid all command timeouts).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify that the device state is registered before un-registering it.
This check is required to prevent an OOPS on flows that do
re-registration of the device and its previous state was
unregistered.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Silent a few smatch warnings about indentation.
This include the removal of a 'return' statement in 'resource_tracker.c'.
This 'return' will still be performed when breaking out of the
corresponding 'switch' block.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlx4 network driver was registered in the context of the 'add'
function of the core driver (called when HW should be registered).
This makes the netdev event NETDEV_REGISTER to be sent in a context
where the answer to get_protocol_dev() callback returns NULL. This may
be confusing to listeners of netdev events.
This patch is a preparation to the patch that implements the
get_netdev() callback in the IB/mlx4 driver.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When in HA mode, the driver exposes an IB (RoCE) device instance with only
one port. Under SRIOV, the existing implementation doesn't go well with
the PF RoCE driver's role of Special QPs Para-Virtualization, etc.
As such, disable HA for the mlx4 PF RoCE device in SRIOV mode.
Fixes: a57500903093 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.
There are
1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports
The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.
The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.
The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning. When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.
The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.
The VF shall reset itself in the following cases:
1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.
2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.
Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.
As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
commands to the PF and getting timed-out.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.
Implement the remove_one case, handling AER and other cases comes next.
The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When running in SRIOV mode, driver should not automatically start/stop
the mlx4_core upon sensing an HCA internal error -- doing this disables/enables
sriov, which will cause the hypervisor to hang if there are running VMs with
attached VFs.
In addition, on VMs the catas process should not run at all, since the HCA
error buffer is not available to VMs in the BARs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
