| Age | Commit message (Collapse) | Author |
|---|
|
After the introduction of a private mac_lock that serializes access to
priv->mac (and port_priv->mac in the switch), the only remaining purpose
of rtnl_lock() is to satisfy the locking requirements of
phylink_fwnode_phy_connect() and phylink_disconnect_phy().
But the functions these live in, dpaa2_mac_connect() and
dpaa2_mac_disconnect(), have contradictory locking requirements.
While phylink_fwnode_phy_connect() wants rtnl_lock() to be held,
phylink_create() wants it to not be held.
Move the rtnl_lock() from top-level (in the dpaa2-eth and dpaa2-switch
drivers) to only surround the phylink calls that require it, in the
dpaa2-mac library code.
This is possible because dpaa2_mac_connect() and dpaa2_mac_disconnect()
run unlocked, and there isn't any danger of an AB/BA deadlock between
the rtnl_mutex and other private locks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The dpaa2 architecture permits dynamic connections between objects on
the fsl-mc bus, specifically between a DPNI object (represented by a
struct net_device) and a DPMAC object (represented by a struct phylink).
The DPNI driver is notified when those connections are created/broken
through the dpni_irq0_handler_thread() method. To ensure that ethtool
operations, as well as netdev up/down operations serialize with the
connection/disconnection of the DPNI with a DPMAC,
dpni_irq0_handler_thread() takes the rtnl_lock() to block those other
operations from taking place.
There is code called by dpaa2_mac_connect() which wants to acquire the
rtnl_mutex once again, see phylink_create() -> phylink_register_sfp() ->
sfp_bus_add_upstream() -> rtnl_lock(). So the strategy doesn't quite
work out, even though it's fairly simple.
Create a different strategy, where all code paths in the dpaa2-eth
driver access priv->mac only while they are holding priv->mac_lock.
The phylink instance is not created or connected to the PHY under the
priv->mac_lock, but only assigned to priv->mac then. This will eliminate
the reliance on the rtnl_mutex.
Add lockdep annotations and put comments where holding the lock is not
necessary, and priv->mac can be dereferenced freely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
dpaa2_eth_connect_mac() is called both from dpaa2_eth_probe() and from
dpni_irq0_handler_thread().
It could happen that the DPNI gets connected to a DPMAC on the fsl-mc
bus exactly during probe, as soon as the "endpoint change" interrupt is
requested in dpaa2_eth_setup_irqs(). This will cause the
dpni_irq0_handler_thread() to register a phylink instance for that DPMAC.
Then, the probing function will also try to register a phylink instance
for the same DPMAC, operation which should fail (and this will fail the
probing of the driver).
Reorder dpaa2_eth_setup_irqs() and dpaa2_eth_connect_mac(), such that
dpni_irq0_handler_thread() never races with the DPMAC-related portion of
the probing path.
Also reorder dpaa2_eth_disconnect_mac() to be in the mirror position of
dpaa2_eth_connect_mac() in the teardown path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are 2 requirements for correct code:
- Any time the driver accesses the priv->mac pointer at runtime, it
either holds NULL to indicate a DPNI-DPNI connection (or unconnected
DPNI), or a struct dpaa2_mac whose phylink instance was fully
initialized (created and connected to the PHY). No changes are made to
priv->mac while it is being used. Currently, rtnl_lock() watches over
the call to dpaa2_eth_connect_mac(), so it serves the purpose of
serializing this with all readers of priv->mac.
- dpaa2_mac_connect() should run unlocked, because inside it are 2
phylink calls with incompatible locking requirements: phylink_create()
requires that the rtnl_mutex isn't held, and phylink_fwnode_phy_connect()
requires that the rtnl_mutex is held. The only way to solve those
contradictory requirements is to let dpaa2_mac_connect() take
rtnl_lock() when it needs to.
To solve both requirements, we need to identify the writer side of the
priv->mac pointer, which can be wrapped in a mutex private to the driver
in a future patch. The dpaa2_mac_connect() cannot be part of the writer
side critical section, because of an AB/BA deadlock with rtnl_lock().
So the strategy needs to be that where we prepare the DPMAC by calling
dpaa2_mac_connect(), and only make priv->mac point to it once it's fully
prepared. This ensures that the writer side critical section has the
absolute minimum surface it can.
The reverse strategy is adopted in the dpaa2_eth_disconnect_mac() code
path. This makes sure that priv->mac is NULL when we start tearing down
the DPMAC that we disconnected from, and concurrent code will simply not
see it.
No locking changes in this patch (concurrent code is still blocked by
the rtnl_mutex).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phylink handling is intended to be hidden inside the dpaa2_mac
object. Move the phylink_start() call into dpaa2_mac_start(), and
phylink_stop() into dpaa2_mac_stop().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
dpaa2_eth_setup_dpni() is called from the probe path and
dpaa2_eth_set_link_ksettings() is propagated to user space.
include/linux/errno.h says that ENOTSUPP is "Defined for the NFSv3
protocol". Conventional wisdom has it to not use it in networking
drivers. Replace it with -EOPNOTSUPP.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Nothing in these file needs anything from linux/msi.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Benefit from the previously implemented tracking of netdev events in
devlink code and instead of calling devlink_port_type_eth_set() and
devlink_port_type_clear() to set devlink port type and link to related
netdev, use SET_NETDEV_DEVLINK_PORT() macro to assign devlink_port
pointer to netdevice which is about to be registered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When this device is deferred, there is often no way to determine what
the cause was. Add some debug prints to make it easier to figure out
what is blocking the probe.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221027190005.400839-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define the dpaa2_tx_xsk_fd and dpaa2_rx_xsk_fd trace events for the XSK
zero-copy Rx and Tx path. Also, define the dpaa2_eth_buf as an event
class so that both dpaa2_eth_buf_seed and dpaa2_xsk_buf_seed traces can
derive from the same class.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support in dpaa2-eth for packet processing on the Tx path using
AF_XDP zero copy mode.
The newly added dpaa2_xsk_tx() function will handle enqueuing AF_XDP Tx
packets into the appropriate queue and update any necessary statistics.
On a more detailed note, the dpaa2_xsk_tx_build_fd() function handles
creating a Scatter-Gather frame descriptor with only one data buffer.
This is needed because otherwise we would need to impose a headroom in
the Tx buffer to store our software annotation structures.
This tactic is already used on the normal data path of the dpaa2-eth
driver, thus we are reusing the dpaa2_eth_sgt_get/dpaa2_eth_sgt_recycle
functions in order to allocate and recycle the Scatter-Gather table
buffers.
In case we have reached the maximum number of Tx XSK packets to be sent
in a NAPI cycle, we'll exit the dpaa2_eth_poll() and hope to be
rescheduled again.
On the XSK Tx confirmation path, we are just unmapping the SGT buffer
and recycle it for further use.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for receiving packets via the AF_XDP
zero-copy mechanism in the dpaa2-eth driver. The support is available
only on the LX2160A SoC and variants because we are relying on the HW
capability to associate a buffer pool to a specific queue (QDBIN), only
available on newer WRIOP versions.
On the control path, the dpaa2_xsk_enable_pool() function is responsible
to allocate a buffer pool (BP), setup this new BP to be used only on the
requested queue and change the consume function to point to the XSK ZC
one.
We are forced to call dev_close() in order to change the queue to buffer
pool association (dpaa2_xsk_set_bp_per_qdbin) . This also works in our
favor since at dev_close() the buffer pools will be drained and at the
later dev_open() call they will be again seeded, this time with buffers
allocated from the XSK pool if needed.
On the data path, a new software annotation type is defined to be used
only for the XSK scenarios. This will enable us to pass keep necessary
information about a packet buffer between the moment in which it was
seeded and when it's received by the driver. In the XSK case, we are
keeping the associated xdp_buff.
Depending on the action returned by the BPF program, we will do the
following:
- XDP_PASS: copy the contents of the packet into a brand new skb,
recycle the initial buffer.
- XDP_TX: just enqueue the same frame descriptor back into the Tx path,
the buffer will get automatically released into the initial BP.
- XDP_REDIRECT: call xdp_do_redirect() and exit.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Carve out code from the dpaa2_eth_rx() function in order to create and
export the dpaa2_eth_receive_skb() function. Do this in order to reuse
this code also from the XSK path which will be introduced in a later
patch.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpaa2_eth_alloc_skb() function is added by moving code from the
dpaa2_eth_copybreak() previously defined function. What the new API does
is to allocate a new skb, copy the frame data from the passed FD to the
new skb and then return the skb.
Export this new function since we'll need the this functionality also
from the XSK code path.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of calling the internal functions which implement .ndo_stop and
.ndo_open, we can simply call dev_close and dev_open, so that we keep
the code cleaner.
Also, in the next patches we'll use the same APIs from other files
without needing to export the internal functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows the configuration of multiple buffer pools associated
with a single DPNI object, each distinct DPBP object not necessarily
shared among all queues.
The user can interogate both the number of buffer pools and the buffer
count in each buffer pool by using the .get_ethtool_stats() callback.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We should trace the allocated address instead of page struct.
Fixes: 27c874867c4e ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20220811151651.3327-1-chen45464546@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DMA unmap the Scatter/Gather table before going through the array to
unmap and free each of the header and data chunks. This is so we do not
touch the data between the dma_map and dma_unmap calls.
Fixes: 3dc709e0cd47 ("dpaa2-eth: add support for software TSO")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The incorrect software annotation field was being used, swa->sg.sgt_size
instead of swa->tso.sgt_size, which meant that the SGT buffer was
unmapped with a wrong size.
This is also confirmed by the DMA API debug prints which showed the
following:
[ 38.962434] DMA-API: fsl_dpaa2_eth dpni.2: device driver frees DMA memory with different size [device address=0x0000fffffafba740] [map size=224 bytes] [unmap size=0 bytes]
[ 38.980496] WARNING: CPU: 11 PID: 1131 at kernel/dma/debug.c:973 check_unmap+0x58c/0x9b0
[ 38.988586] Modules linked in:
[ 38.991631] CPU: 11 PID: 1131 Comm: iperf3 Not tainted 5.18.0-rc7-00117-g59130eeb2b8f #1972
[ 38.999970] Hardware name: NXP Layerscape LX2160ARDB (DT)
Fixes: 3dc709e0cd47 ("dpaa2-eth: add support for software TSO")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO header was DMA unmapped before the virtual address was retrieved
and then used to free the buffer. This meant that we were actually
removing the DMA map and then trying to search for it to help in
retrieving the virtual address. This lead to a invalid virtual address
being used in the kfree call.
Fix this by calling dpaa2_iova_to_virt() prior to the dma_unmap call.
[ 487.231819] Unable to handle kernel paging request at virtual address fffffd9807000008
(...)
[ 487.354061] Hardware name: SolidRun LX2160A Honeycomb (DT)
[ 487.359535] pstate: a0400005 (NzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 487.366485] pc : kfree+0xac/0x304
[ 487.369799] lr : kfree+0x204/0x304
[ 487.373191] sp : ffff80000c4eb120
[ 487.376493] x29: ffff80000c4eb120 x28: ffff662240c46400 x27: 0000000000000001
[ 487.383621] x26: 0000000000000001 x25: ffff662246da0cc0 x24: ffff66224af78000
[ 487.390748] x23: ffffad184f4ce008 x22: ffffad1850185000 x21: ffffad1838d13cec
[ 487.397874] x20: ffff6601c0000000 x19: fffffd9807000000 x18: 0000000000000000
[ 487.405000] x17: ffffb910cdc49000 x16: ffffad184d7d9080 x15: 0000000000004000
[ 487.412126] x14: 0000000000000008 x13: 000000000000ffff x12: 0000000000000000
[ 487.419252] x11: 0000000000000004 x10: 0000000000000001 x9 : ffffad184d7d927c
[ 487.426379] x8 : 0000000000000000 x7 : 0000000ffffffd1d x6 : ffff662240a94900
[ 487.433505] x5 : 0000000000000003 x4 : 0000000000000009 x3 : ffffad184f4ce008
[ 487.440632] x2 : ffff662243eec000 x1 : 0000000100000100 x0 : fffffc0000000000
[ 487.447758] Call trace:
[ 487.450194] kfree+0xac/0x304
[ 487.453151] dpaa2_eth_free_tx_fd.isra.0+0x33c/0x3e0 [fsl_dpaa2_eth]
[ 487.459507] dpaa2_eth_tx_conf+0x100/0x2e0 [fsl_dpaa2_eth]
[ 487.464989] dpaa2_eth_poll+0xdc/0x380 [fsl_dpaa2_eth]
Fixes: 3dc709e0cd47 ("dpaa2-eth: add support for software TSO")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215886
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch integrates the dpaa2-eth driver with the generic PHY
infrastructure in order to search, find and reconfigure the SerDes lanes
in case of a protocol change.
On the .mac_config() callback, the phy_set_mode_ext() API is called so
that the Lynx 28G SerDes PHY driver can change the lane's configuration.
In the same phylink callback the MC firmware is called so that it
reconfigures the MAC side to run using the new protocol.
The consumer drivers - dpaa2-eth and dpaa2-switch - are updated to call
the dpaa2_mac_start/stop functions newly added which will
power_on/power_off the associated SerDes lane.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DPAA2 MAC supports 1588 one step timestamping.
If this option is enabled then for each transmitted PTP event packet,
the 1588 SINGLE_STEP register is accessed to modify the following fields:
-offset of the correction field inside the PTP packet
-UDP checksum update bit, in case the PTP event packet has
UDP encapsulation
These values can change any time, because there may be multiple
PTP clients connected, that receive various 1588 frame types:
- L2 only frame
- UDP / Ipv4
- UDP / Ipv6
- other
The current implementation uses dpni_set_single_step_cfg to update the
SINLGE_STEP register.
Using an MC command on the Tx datapath for each transmitted 1588 message
introduces high delays, leading to low throughput and consequently to a
small number of supported PTP clients. Besides these, the nanosecond
correction field from the PTP packet will contain the high delay from the
driver which together with the originTimestamp will render timestamp
values that are unacceptable in a GM clock implementation.
This patch updates the Tx datapath for 1588 messages when single step
timestamp is enabled and provides direct access to SINGLE_STEP register,
eliminating the overhead caused by the dpni_set_single_step_cfg
MC command. MC version >= 10.32 implements this functionality.
If the MC version does not have support for returning the
single step register base address, the driver will use
dpni_set_single_step_cfg command for updates operations.
All the delay introduced by dpni_set_single_step_cfg
function will be eliminated (if MC version has support for returning the
base address of the single step register), improving the egress driver
performance for PTP packets when single step timestamping is enabled.
Before these changes the maximum throughput for 1588 messages with
single step hardware timestamp enabled was around 2000pps.
After the updates the throughput increased up to 32.82 Mbps / 46631.02 pps.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following coccicheck warnings:
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1199:42-47: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1218:54-59: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1588 Single Step Timestamping code path uses a mutex to
enforce atomicity for two events:
- update of ptp single step register
- transmit ptp event packet
Before this patch the mutex was not initialized. This
caused unexpected crashes in the Tx function.
Fixes: c55211892f463 ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The netdev should be unregistered before we are disconnecting from the
MAC/PHY so that the dev_close callback is called and the PHY and the
phylink workqueues are actually stopped before we are disconnecting and
destroying the phylink instance.
Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for driver level TSO in the enetc driver using
the TSO API.
There is not much to say about this specific implementation. We are
using the usual tso_build_hdr(), tso_build_data() to create each data
segment, we create an array of S/G FDs where the first S/G entry is
referencing the header data and the remaining ones the data portion.
For the S/G Table buffer we use the same cache of buffers used on the
other non-GSO cases - dpaa2_eth_sgt_get() and dpaa2_eth_sgt_recycle().
We cannot keep a DMA coherent buffer for all the TSO headers because the
DPAA2 architecture does not work in a ring based fashion so we just
allocate a buffer each time.
Even with these limitations we get the following improvement in TCP
termination on the LX2160A SoC, on a single A72 core running at 2.2GHz.
before: 6.38Gbit/s
after: 8.48Gbit/s
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now, the __dpaa2_eth_tx function used a single FD on the stack
to construct the structure to be enqueued. Since we are now preparing
the ground work to add support for TSO done in software at the driver
level, the same function needs to work with an array of FDs and enqueue
as many as the build_*_fd functions create.
Make the necessary adjustments in order to do this. These include:
keeping an array of FDs in a percpu structure, cleaning up the necessary
FDs before populating it and then, retrying the enqueue process up till
all the generated FDs were enqueued or until we reach the maximum number
retries.
This patch does not change the fact that only a single FD will result
from a __dpaa2_eth_tx call but rather just creates the necessary changes
for the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of allocating memory for an S/G table each time a nonlinear skb
is processed, and then freeing it on the Tx confirmation path, use the
S/G table cache in order to reuse the memory.
For this to work we have to change the size of the cached buffers so
that it can hold the maximum number of scatterlist entries.
Other than that, each allocate/free call is replaced by a call to the
dpaa2_eth_sgt_get/dpaa2_eth_sgt_recycle functions, introduced in the
previous patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpaa2-eth driver uses in certain circumstances a buffer cache for
the S/G tables needed in case of a S/G FD. At the moment, the
interraction with the cache is open-coded and couldn't be reused easily.
Add two new functions - dpaa2_eth_sgt_get and dpaa2_eth_sgt_recycle -
which help with code reusability.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of allocating memory and then manually aligning it to the
desired value use napi_alloc_frag_align() directly to streamline the
process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the next patches we'll be moving things arroung in the mentioned
function and also add some new variable declarations. Before all this,
cleanup the variable declaration order.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
|
|
Storing a pointer to the MSI descriptor just to track the Linux interrupt
number is daft. Just store the interrupt number and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221815.207838579@linutronix.de
|
|
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
|
|
The commit c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it.
Fixes: 7472dd9f6499 ("staging: fsl-dpaa2/eth: Move print message")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for adaptive interrupt coalescing to the dpaa2-eth driver.
First of all, ETHTOOL_COALESCE_USE_ADAPTIVE_RX is defined as a supported
coalesce parameter and the requested state is configured through the
dpio APIs added in the previous patch.
Besides the ethtool API interaction, we keep track of how many bytes and
frames are dequeued per CDAN (Channel Data Availability Notification)
and update the Net DIM instance through the dpaa2_io_update_net_dim()
API.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move devlink_register to be the last command in the initialization
sequence.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of a switch DPAA2 object, the interface ID is also needed when
querying for the object endpoint. Extend fsl_mc_get_endpoint() so that
users can also pass the interface ID that are interested in.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dpaa and dpaa2 drivers have rcu_read_lock()/rcu_read_unlock() pairs
around XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-11-toke@redhat.com
|
|
When booting a board with DPAA2 interfaces defined statically via DPL
(as opposed to creating them dynamically using restool), the driver will
print an unspecific error message.
This change adds the error code to the message, and avoids printing
altogether if the error code is EPROBE_DEFER, because that is not a
cause of alarm.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's useful, especially for debugging purposes, to have the Rx copybreak
value changeable at runtime. Export it as an ethtool tunable.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA unmapping, allocating a new buffer and DMA mapping it back on the
refill path is really not that efficient. Proper buffer recycling (page
pool, flipping the page and using the other half) cannot be done for
DPAA2 since it's not a ring based controller but it rather deals with
multiple queues which all get their buffers from the same buffer pool on
Rx.
To circumvent these limitations, add support for Rx copybreak. For small
sized packets instead of creating a skb around the buffer in which the
frame was received, allocate a new sk buffer altogether, copy the
contents of the frame and release the initial page back into the buffer
pool.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the dpaa2_eth_xdp_release_buf function into dpaa2_eth_recycle_buf
since in the next patches we'll be using the same recycle mechanism for
the normal stack path beside for XDP_DROP.
Also, rename the array which holds the buffers to be recycled so that it
does not have any reference to XDP.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
|
