| Age | Commit message (Collapse) | Author |
|---|
|
'rockchip', 'verisilicon', 'riscv', 'intel/vt-d', 'amd/amd-vi' and 'core' into next
|
|
In init_iommu_one(), when processing IOMMU EFR attributes, the code checks
whether GASUP is enabled. If GASUP is not enabled, the code falls back to
legacy guest IR mode and then breaks out of the switch statement.
This break incorrectly skips the subsequent initialization steps that
follow the GASUP check. These initializations are independent of GASUP
support and must always be performed.
Fix this by replacing the early break with a conditional else block,
ensuring that the XTSUP check is only skipped when GASUP is not available.
Fixes: a44092e326d4 ("iommu/amd: Use IVHD EFR for early initialization of IOMMU features")
Reported-by: Sudheer Dantuluri <dantuluris@google.com>
Tested-by: Dheeraj Kumar Srivastava <dheerajkumar.srivastava@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
ACPI IVRS IVHD’s IVINFO field reports the maximum virtual address
size (VASIZE) supported by the IOMMU. The AMD IOMMU driver currently
caps this with pagetable level reported by EFR[HATS] when configuring
paging domains (hw_max_vasz_lg2). On systems where firmware or VM
advertises smaller or different limits, the driver may over-advertise
capabilities and create domains outside the hardware’s actual bounds.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Ankit Soni <Ankit.Soni@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The SB IOAPIC is on the device 0xb from Hygon family 18h model 4h.
Signed-off-by: Fu Hao <fuhao@open-hieco.net>
Tested-by: Tingyin Duan <tingyin.duan@gmail.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Exclusion ranges in IVMD are treated as unity mappings with r&w
permissions since commit 0bbe4ced53e3 ("iommu/amd: Fix the
overwritten field in IVMD header"), using 1:1 mappings. And IOMMU
Exclusion Base & Range Limit Registers (0x0020/0x0028) are actually
no longer used.
As a result, several definitions and code paths became dead code:
- exclusion_start/exclusion_length in struct amd_iommu are never
assigned,
- iommu_set_exclusion_range() always returns 0 now.
- MMIO_EXCL_ENABLE_MASK & MMIO_EXCL_ALLOW_MASK are only used by
the removed iommu_set_exclusion_range().
- DEV_ENTRY_EX is no longer set in any DTE.
- IOMMU_UNITY_MAP_FLAG_EXCL_RANGE is no longer set, thus the
IOMMU_RESV_RESERVED branch in amd_iommu_get_resv_regions() is
no longer reachable.
Just remove all of the dead code. No functional change.
Signed-off-by: Yu Zhang <zhangyu1@linux.microsoft.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Jacob Pan <jacob.pan@linux.microsoft.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Bail early from enable_iommus_vapic() if IOMMUs are configured for either
of the legacy modes, as it's absurdly difficult to see that
iommu_ga_log_enable() is guaranteed to fail because iommu_init_ga_log()
skips allocating the ga_log.
Opportunistically have iommu_ga_log_enable() WARN if it's called without
IOMMUs being configured to support AVIC/vAPIC.
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Due to CVE-2023-20585, the PPR log buffer must use the maximum supported
size (512K) on Genoa (Family 0x19, model >= 0x10) systems when SNP is
enabled, to mitigate a potential security vulnerability. Note that Family
0x19 models below 0x10 (Milan) do not support PPR when SNP is enabled.
Hence the PPR log size increase is only applied for model >= 0x10.
All other systems continue to use the default PPR log buffer size (8K).
Apply the errata fix by making the following changes:
- Introduce global new variable (amd_iommu_pprlog_size) to have PPR log buffer
size. Adjust variable size for Genoa family.
- Extend 'amd_iommu_apply_erratum_snp()' to also set the PPR log buffer
size to maximum for Family 0x19 model >= 0x10 when SNP is enabled.
- Rename PPR_* macros to make it more readable.
Link: https://www.amd.com/en/resources/product-security/bulletin/amd-sb-3016.html
Cc: Borislav Petkov <bp@alien8.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Dheeraj Kumar Srivastava <dheerajkumar.srivastava@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Due to CVE-2023-20585, the Event log buffer must use the maximum supported
size (512K) on Milan/Genoa (Family 0x19) systems when SNP is enabled,
to mitigate a potential security vulnerability. All other systems continue to
use the default Event log buffer size (8K).
Apply the errata fix by making the following changes:
* Introduce new global variable (amd_iommu_evtlog_size) to have event log
buffer size. Adjust variable size for family 0x19.
* Since 'iommu_snp_enable()' must be called after the core IOMMU subsystem
is initialized, it cannot be moved to the early init stage. The SNP errata
must also be applied after the 'iommu_snp_enable()' check. Therefore,
'alloc_event_buffer()' and 'iommu_enable_event_buffer()' are now called
in the IOMMU_ENABLED state, after the errata is applied.
* Adjust alloc_event_buffer() and iommu_enable_event_buffer() to handle
all IOMMU instances.
* Also rename EVT_* macros to make it more readable.
Link: https://www.amd.com/en/resources/product-security/bulletin/amd-sb-3016.html
Cc: Borislav Petkov <bp@alien8.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Dheeraj Kumar Srivastava <dheerajkumar.srivastava@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Currently, PPR Log and GA logs for AMD IOMMU are allocated using
iommu_alloc_pages_sz(), which does not account for NUMA affinity. This can
lead to remote memory access latencies if the memory is allocated on a
different node than the IOMMU hardware.
Switch to iommu_alloc_pages_node_sz() to ensure that these data structures
are allocated on the same NUMA node as the IOMMU device. If the node
information is unavailable, it defaults to NUMA_NO_NODE.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Ankit Soni <Ankit.Soni@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Conversion performed via this Coccinelle script:
// SPDX-License-Identifier: GPL-2.0-only
// Options: --include-headers-for-types --all-includes --include-headers --keep-comments
virtual patch
@gfp depends on patch && !(file in "tools") && !(file in "samples")@
identifier ALLOC = {kmalloc_obj,kmalloc_objs,kmalloc_flex,
kzalloc_obj,kzalloc_objs,kzalloc_flex,
kvmalloc_obj,kvmalloc_objs,kvmalloc_flex,
kvzalloc_obj,kvzalloc_objs,kvzalloc_flex};
@@
ALLOC(...
- , GFP_KERNEL
)
$ make coccicheck MODE=patch COCCI=gfp.cocci
Build and boot tested x86_64 with Fedora 42's GCC and Clang:
Linux version 6.19.0+ (user@host) (gcc (GCC) 15.2.1 20260123 (Red Hat 15.2.1-7), GNU ld version 2.44-12.fc42) #1 SMP PREEMPT_DYNAMIC 1970-01-01
Linux version 6.19.0+ (user@host) (clang version 20.1.8 (Fedora 20.1.8-4.fc42), LLD 20.1.8) #1 SMP PREEMPT_DYNAMIC 1970-01-01
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core changes:
- Rust bindings for IO-pgtable code
- IOMMU page allocation debugging support
- Disable ATS during PCI resets
Intel VT-d changes:
- Skip dev-iotlb flush for inaccessible PCIe device
- Flush cache for PASID table before using it
- Use right invalidation method for SVA and NESTED domains
- Ensure atomicity in context and PASID entry updates
AMD-Vi changes:
- Support for nested translations
- Other minor improvements
ARM-SMMU-v2 changes:
- Configure SoC-specific prefetcher settings for Qualcomm's "MDSS"
ARM-SMMU-v3 changes:
- Improve CMDQ locking fairness for pathetically small queue sizes
- Remove tracking of the IAS as this is only relevant for AArch32 and
was causing C_BAD_STE errors
- Add device-tree support for NVIDIA's CMDQV extension
- Allow some hitless transitions for the 'MEV' and 'EATS' STE fields
- Don't disable ATS for nested S1-bypass nested domains
- Additions to the kunit selftests"
* tag 'iommu-updates-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (54 commits)
iommupt: Always add IOVA range to iotlb_gather in gather_range_pages()
iommu/amd: serialize sequence allocation under concurrent TLB invalidations
iommu/amd: Fix type of type parameter to amd_iommufd_hw_info()
iommu/arm-smmu-v3: Do not set disable_ats unless vSTE is Translate
iommu/arm-smmu-v3-test: Add nested s1bypass/s1dssbypass coverage
iommu/arm-smmu-v3: Mark EATS_TRANS safe when computing the update sequence
iommu/arm-smmu-v3: Mark STE MEV safe when computing the update sequence
iommu/arm-smmu-v3: Add update_safe bits to fix STE update sequence
iommu/arm-smmu-v3: Add device-tree support for CMDQV driver
iommu/tegra241-cmdqv: Decouple driver from ACPI
iommu/arm-smmu-qcom: Restore ACTLR settings for MDSS on sa8775p
iommu/vt-d: Fix race condition during PASID entry replacement
iommu/vt-d: Clear Present bit before tearing down context entry
iommu/vt-d: Clear Present bit before tearing down PASID entry
iommu/vt-d: Flush piotlb for SVM and Nested domain
iommu/vt-d: Flush cache for PASID table before using it
iommu/vt-d: Flush dev-IOTLB only when PCIe device is accessible in scalable mode
iommu/vt-d: Skip dev-iotlb flush for inaccessible PCIe device without scalable mode
rust: iommu: fix `srctree` link warning
rust: iommu: fix Rust formatting
...
|
|
With concurrent TLB invalidations, completion wait randomly gets timed out
because cmd_sem_val was incremented outside the IOMMU spinlock, allowing
CMD_COMPL_WAIT commands to be queued out of sequence and breaking the
ordering assumption in wait_on_sem().
Move the cmd_sem_val increment under iommu->lock so completion sequence
allocation is serialized with command queuing.
And remove the unnecessary return.
Fixes: d2a0cac10597 ("iommu/amd: move wait_on_sem() out of spinlock")
Tested-by: Srikanth Aithal <sraithal@amd.com>
Reported-by: Srikanth Aithal <sraithal@amd.com>
Signed-off-by: Ankit Soni <Ankit.Soni@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
request_threaded_irq() is invoked with a primary and a secondary handler
and no flags are passed. The primary handler is the same as
irq_default_primary_handler() so there is no need to have an identical
copy.
The lack of the IRQF_ONESHOT can be dangerous because the interrupt
source is not masked while the threaded handler is active. This means,
especially on LEVEL typed interrupt lines, the interrupt can fire again
before the threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: 72fe00f01f9a3 ("x86/amd-iommu: Use threaded interupt handler")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-4-bigeasy@linutronix.de
|
|
The GCR3TRPMode feature allows the DTE[GCR3TRP] field to be configured
with GPA (instead of SPA). This simplifies the implementation, and is
a pre-requisite for nested translation support.
Therefore, always enable this feature if available.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Also change the define to use GENMASK_ULL instead.
There is no functional change.
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
So that both iommu.c and init.c can utilize them. Also define a new
function 'pdom_id_destroy()' to destroy 'pdom_ids' instead of directly
calling ida functions.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Currently AMD IOMMU driver does not reserve domain ids programmed in the
DTE while reusing the device table inside kdump kernel. This can cause
reallocation of these domain ids for newer domains that are created by
the kdump kernel, which can lead to potential IO_PAGE_FAULTs
Hence reserve these ids inside pdom_ids.
Fixes: 38e5f33ee359 ("iommu/amd: Reuse device table for kdump")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm
Pull PCIe Link Encryption and Device Authentication from Dan Williams:
"New PCI infrastructure and one architecture implementation for PCIe
link encryption establishment via platform firmware services.
This work is the result of multiple vendors coming to consensus on
some core infrastructure (thanks Alexey, Yilun, and Aneesh!), and
three vendor implementations, although only one is included in this
pull. The PCI core changes have an ack from Bjorn, the crypto/ccp/
changes have an ack from Tom, and the iommu/amd/ changes have an ack
from Joerg.
PCIe link encryption is made possible by the soup of acronyms
mentioned in the shortlog below. Link Integrity and Data Encryption
(IDE) is a protocol for installing keys in the transmitter and
receiver at each end of a link. That protocol is transported over Data
Object Exchange (DOE) mailboxes using PCI configuration requests.
The aspect that makes this a "platform firmware service" is that the
key provisioning and protocol is coordinated through a Trusted
Execution Envrionment (TEE) Security Manager (TSM). That is either
firmware running in a coprocessor (AMD SEV-TIO), or quasi-hypervisor
software (Intel TDX Connect / ARM CCA) running in a protected CPU
mode.
Now, the only reason to ask a TSM to run this protocol and install the
keys rather than have a Linux driver do the same is so that later, a
confidential VM can ask the TSM directly "can you certify this
device?".
That precludes host Linux from provisioning its own keys, because host
Linux is outside the trust domain for the VM. It also turns out that
all architectures, save for one, do not publish a mechanism for an OS
to establish keys in the root port. So "TSM-established link
encryption" is the only cross-architecture path for this capability
for the foreseeable future.
This unblocks the other arch implementations to follow in v6.20/v7.0,
once they clear some other dependencies, and it unblocks the next
phase of work to implement the end-to-end flow of confidential device
assignment. The PCIe specification calls this end-to-end flow Trusted
Execution Environment (TEE) Device Interface Security Protocol
(TDISP).
In the meantime, Linux gets a link encryption facility which has
practical benefits along the same lines as memory encryption. It
authenticates devices via certificates and may protect against
interposer attacks trying to capture clear-text PCIe traffic.
Summary:
- Introduce the PCI/TSM core for the coordination of device
authentication, link encryption and establishment (IDE), and later
management of the device security operational states (TDISP).
Notify the new TSM core layer of PCI device arrival and departure
- Add a low level TSM driver for the link encryption establishment
capabilities of the AMD SEV-TIO architecture
- Add a library of helpers TSM drivers to use for IDE establishment
and the DOE transport
- Add skeleton support for 'bind' and 'guest_request' operations in
support of TDISP"
* tag 'tsm-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm: (23 commits)
crypto/ccp: Fix CONFIG_PCI=n build
virt: Fix Kconfig warning when selecting TSM without VIRT_DRIVERS
crypto/ccp: Implement SEV-TIO PCIe IDE (phase1)
iommu/amd: Report SEV-TIO support
psp-sev: Assign numbers to all status codes and add new
ccp: Make snp_reclaim_pages and __sev_do_cmd_locked public
PCI/TSM: Add 'dsm' and 'bound' attributes for dependent functions
PCI/TSM: Add pci_tsm_guest_req() for managing TDIs
PCI/TSM: Add pci_tsm_bind() helper for instantiating TDIs
PCI/IDE: Initialize an ID for all IDE streams
PCI/IDE: Add Address Association Register setup for downstream MMIO
resource: Introduce resource_assigned() for discerning active resources
PCI/TSM: Drop stub for pci_tsm_doe_transfer()
drivers/virt: Drop VIRT_DRIVERS build dependency
PCI/TSM: Report active IDE streams
PCI/IDE: Report available IDE streams
PCI/IDE: Add IDE establishment helpers
PCI: Establish document for PCI host bridge sysfs attributes
PCI: Add PCIe Device 3 Extended Capability enumeration
PCI/TSM: Establish Secure Sessions and Link Encryption
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"This is the first half of the driver changes:
- A treewide interface change to the "syscore" operations for power
management, as a preparation for future Tegra specific changes
- Reset controller updates with added drivers for LAN969x, eic770 and
RZ/G3S SoCs
- Protection of system controller registers on Renesas and Google
SoCs, to prevent trivially triggering a system crash from e.g.
debugfs access
- soc_device identification updates on Nvidia, Exynos and Mediatek
- debugfs support in the ST STM32 firewall driver
- Minor updates for SoC drivers on AMD/Xilinx, Renesas, Allwinner, TI
- Cleanups for memory controller support on Nvidia and Renesas"
* tag 'soc-drivers-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (114 commits)
memory: tegra186-emc: Fix missing put_bpmp
Documentation: reset: Remove reset_controller_add_lookup()
reset: fix BIT macro reference
reset: rzg2l-usbphy-ctrl: Fix a NULL vs IS_ERR() bug in probe
reset: th1520: Support reset controllers in more subsystems
reset: th1520: Prepare for supporting multiple controllers
dt-bindings: reset: thead,th1520-reset: Add controllers for more subsys
dt-bindings: reset: thead,th1520-reset: Remove non-VO-subsystem resets
reset: remove legacy reset lookup code
clk: davinci: psc: drop unused reset lookup
reset: rzg2l-usbphy-ctrl: Add support for RZ/G3S SoC
reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G3S support
reset: eswin: Add eic7700 reset driver
dt-bindings: reset: eswin: Documentation for eic7700 SoC
reset: sparx5: add LAN969x support
dt-bindings: reset: microchip: Add LAN969x support
soc: rockchip: grf: Add select correct PWM implementation on RK3368
soc/tegra: pmc: Add USB wake events for Tegra234
amba: tegra-ahb: Fix device leak on SMMU enable
...
|
|
The SEV-TIO switch in the AMD BIOS is reported to the OS via
the IOMMU Extended Feature 2 register (EFR2), bit 1.
Add helper to parse the bit and report the feature presence.
Signed-off-by: Alexey Kardashevskiy <aik@amd.com>
Link: https://patch.msgid.link/20251202024449.542361-4-aik@amd.com
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Several drivers can benefit from registering per-instance data along
with the syscore operations. To achieve this, move the modifiable fields
out of the syscore_ops structure and into a separate struct syscore that
can be registered with the framework. Add a void * driver data field for
drivers to store contextual data that will be passed to the syscore ops.
Acked-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fix a memory leak of struct amd_iommu_pci_segment in alloc_pci_segment()
when system memory (or contiguous memory) is insufficient.
Fixes: 04230c119930 ("iommu/amd: Introduce per PCI segment device table")
Fixes: eda797a27795 ("iommu/amd: Introduce per PCI segment rlookup table")
Fixes: 99fc4ac3d297 ("iommu/amd: Introduce per PCI segment alias_table")
Cc: stable@vger.kernel.org
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
'amd/amd-vi' into next
|
|
Commit 7bea695ada0 restructured DTE flag handling but inadvertently changed
the alias device configuration logic. This may cause incorrect DTE settings
for certain devices.
Add alias flag check before calling set_dev_entry_from_acpi(). Also move the
device iteration loop inside the alias check to restrict execution to cases
where alias devices are present.
Fixes: 7bea695ada0 ("iommu/amd: Introduce struct ivhd_dte_flags to store persistent DTE flags")
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Fix a permanent ACPI table memory leak in early_amd_iommu_init() when
CMPXCHG16B feature is not supported
Fixes: 82582f85ed22 ("iommu/amd: Disable AMD IOMMU if CMPXCHG16B feature is not supported")
Cc: stable@vger.kernel.org
Signed-off-by: Zhen Ni <zhen.ni@easystack.cn>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20250822024915.673427-1-zhen.ni@easystack.cn
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/576445eb4f168b467b0fc789079b650ca7c5b037.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU device table register is locked and exclusive to the previous
kernel. Attempts to copy old device table from the previous kernel
fails in kdump kernel as hardware ignores writes to the locked device
table base address register as per AMD IOMMU spec Section 2.12.2.1.
This causes the IOMMU driver (OS) and the hardware to reference
different memory locations. As a result, the IOMMU hardware cannot
process the command which results in repeated "Completion-Wait loop
timed out" errors and a second kernel panic: "Kernel panic - not
syncing: timer doesn't work through Interrupt-remapped IO-APIC".
Reuse device table instead of copying device table in case of kdump
boot and remove all copying device table code.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/3a31036fb2f7323e6b1a1a1921ac777e9f7bdddc.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU completion wait buffers (CWBs), command buffers and event buffer
registers remain locked and exclusive to the previous kernel. Attempts
to allocate and use new buffers in the kdump kernel fail, as hardware
ignores writes to the locked MMIO registers as per AMD IOMMU spec
Section 2.12.2.1.
This results in repeated "Completion-Wait loop timed out" errors and a
second kernel panic: "Kernel panic - not syncing: timer doesn't work
through Interrupt-remapped IO-APIC"
The list of MMIO registers locked and which ignore writes after failed
SNP shutdown are mentioned in the AMD IOMMU specifications below:
Section 2.12.2.1.
https://docs.amd.com/v/u/en-US/48882_3.10_PUB
Reuse the pages of the previous kernel for completion wait buffers,
command buffers, event buffers and memremap them during kdump boot
and essentially work with an already enabled IOMMU configuration and
re-using the previous kernel’s data structures.
Reusing of command buffers and event buffers is now done for kdump boot
irrespective of SNP being enabled during kdump.
Re-use of completion wait buffers is only done when SNP is enabled as
the exclusion base register is used for the completion wait buffer
(CWB) address only when SNP is enabled.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/ff04b381a8fe774b175c23c1a336b28bc1396511.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
While the kernel command line is considered trusted in most environments,
avoid writing 1 byte past the end of "acpiid" if the "str" argument is
maximum length.
Reported-by: Simcha Kosman <simcha.kosman@cyberark.com>
Closes: https://lore.kernel.org/all/AS8P193MB2271C4B24BCEDA31830F37AE84A52@AS8P193MB2271.EURP193.PROD.OUTLOOK.COM
Fixes: b6b26d86c61c ("iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Ankit Soni <Ankit.Soni@amd.com>
Link: https://lore.kernel.org/r/20250804154023.work.970-kees@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Rearrange initial setup of AMD IOMMU debugfs to segregate per IOMMU
setup and setup which is common for all IOMMUs. This ensures that common
debugfs paths (introduced in subsequent patches) are created only once
instead of being created for each IOMMU.
With the change, there is no need to use lock as amd_iommu_debugfs_setup()
will be called only once during AMD IOMMU initialization. So remove lock
acquisition in amd_iommu_debugfs_setup().
Signed-off-by: Dheeraj Kumar Srivastava <dheerajkumar.srivastava@amd.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250702093804.849-2-dheerajkumar.srivastava@amd.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The EFR[HATS] bits indicate maximum host translation level supported by
IOMMU. Adding support to set the maximum host page table level as indicated
by EFR[HATS]. If the HATS=11b (reserved), the driver will attempt to use
guest page table for DMA API.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Ankit Soni <Ankit.Soni@amd.com>
Link: https://lore.kernel.org/r/df0f8562c2a20895cc185c86f1a02c4d826fd597.1749016436.git.Ankit.Soni@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Current AMD IOMMU assumes Host Address Translation (HAT) is always
supported, and Linux kernel enables this capability by default. However,
in case of emulated and virtualized IOMMU, this might not be the case.
For example,current QEMU-emulated AMD vIOMMU does not support host
translation for VFIO pass-through device, but the interrupt remapping
support is required for x2APIC (i.e. kvm-msi-ext-dest-id is also not
supported by the guest OS). This would require the guest kernel to boot
with guest kernel option iommu=pt to by-pass the initialization of
host (v1) table.
The AMD I/O Virtualization Technology (IOMMU) Specification Rev 3.10 [1]
introduces a new flag 'HATDis' in the IVHD 11h IOMMU attributes to indicate
that HAT is not supported on a particular IOMMU instance.
Therefore, modifies the AMD IOMMU driver to detect the new HATDis
attributes, and disable host translation and switch to use guest
translation if it is available. Otherwise, the driver will disable DMA
translation.
[1] https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/specifications/48882_IOMMU.pdf
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Ankit Soni <Ankit.Soni@amd.com>
Link: https://lore.kernel.org/r/8109b208f87b80e400c2abd24a2e44fcbc0763a5.1749016436.git.Ankit.Soni@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
|
|
'arm/smmu/bindings', 'fsl/pamu', 'mediatek', 'renesas/ipmmu', 's390', 'intel/vt-d', 'amd/amd-vi' and 'core' into next
|
|
Commit 991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") changed IRQ handling on PCI driver probing.
It inadvertently broke resume from system sleep on AMD platforms:
https://lore.kernel.org/r/20150926164651.GA3640@pd.tnic/
This was fixed by two independent commits:
* 8affb487d4a4 ("x86/PCI: Don't alloc pcibios-irq when MSI is enabled")
* cbbc00be2ce3 ("iommu/amd: Prevent binding other PCI drivers to IOMMU PCI devices")
The breaking change and one of these two fixes were subsequently reverted:
* fe25d078874f ("Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"")
* 6c777e8799a9 ("Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"")
This rendered the second fix unnecessary, so revert it as well. It used
the match_driver flag in struct pci_dev, which is internal to the PCI core
and not supposed to be touched by arbitrary drivers.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://patch.msgid.link/9a3ddff5cc49512044f963ba0904347bd404094d.1745572340.git.lukas@wunner.de
|
|
AMD IOMMU reserves the address range 0xfd00000000-0xffffffffff for
the hypertransport protocol (HT) and has special meaning. Hence devices
cannot use this address range for the DMA. However on some AMD platforms
this HT range is shifted to the very top of the address space and new
feature bit `HTRangeIgnore` is introduced. When this feature bit is on,
IOMMU treats the GPA access to the legacy HT range as regular GPA access.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250317055020.25214-1-sarunkod@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
There is a string parsing logic error which can lead to an overflow of hid
or uid buffers. Comparing ACPIID_LEN against a total string length doesn't
take into account the lengths of individual hid and uid buffers so the
check is insufficient in some cases. For example if the length of hid
string is 4 and the length of the uid string is 260, the length of str
will be equal to ACPIID_LEN + 1 but uid string will overflow uid buffer
which size is 256.
The same applies to the hid string with length 13 and uid string with
length 250.
Check the length of hid and uid strings separately to prevent
buffer overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ca3bf5d47cec ("iommu/amd: Introduces ivrs_acpihid kernel parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Paklov <Pavel.Paklov@cyberprotect.ru>
Link: https://lore.kernel.org/r/20250325092259.392844-1-Pavel.Paklov@cyberprotect.ru
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Convert most of the places calling get_order() as an argument to the
iommu-pages allocator into order_base_2() or the _sz flavour
instead. These places already have an exact size, there is no particular
reason to use order here.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/19-v4-c8663abbb606+3f7-iommu_pages_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
If x >= PAGE_SIZE then:
1 << (get_order(x) + PAGE_SHIFT) == roundup_pow_two()
Inline this into the only caller, compute the size of the HW device table
in terms of 4K pages which matches the HW definition.
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/17-v4-c8663abbb606+3f7-iommu_pages_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This is just CPU memory used by the driver to track things, it doesn't
need to use iommu-pages. All of them are indexed by devid and devid is
bounded by pci_seg->last_bdf or we are already out of bounds on the page
allocation.
Switch them to use some version of kvmalloc_array() and drop the now
unused constants and remove the tbl_size() round up to PAGE_SIZE multiples
logic.
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/16-v4-c8663abbb606+3f7-iommu_pages_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Use iommu_free_pages() instead.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/6-v4-c8663abbb606+3f7-iommu_pages_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that we have a folio under the allocation iommu_free_pages() can know
the order of the original allocation and do the correct thing to free it.
The next patch will rename iommu_free_page() to iommu_free_pages() so we
have naming consistency with iommu_alloc_pages_node().
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/5-v4-c8663abbb606+3f7-iommu_pages_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
AMD IOMMU optionally supports up to 2K interrupts per function on newer
platforms. Support for this feature is indicated through Extended
Feature 2 Register (MMIO Offset 01A0h[NumIntRemapSup]). Allocate 2K IRTEs
per device when this support is available.
Co-developed-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Kishon Vijay Abraham I <kvijayab@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250307095822.2274-5-sarunkod@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
AMD iommu can support both 512 and 2K interrupts on newer platform. Hence
add suffix "512" to the existing macros.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250307095822.2274-4-sarunkod@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit 05152a049444 ("iommu/amd: Add slab-cache for irq remapping tables")
introduces slab cache allocator. But slab cache allocator provides benefit
only when the allocation and deallocation of many identical objects is
frequent. The AMD IOMMU driver allocates Interrupt remapping table (IRT)
when device driver requests IRQ for the first time and never frees it.
Hence the slab allocator does not provide any benefit here.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250307095822.2274-3-sarunkod@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Define generic function `iommu_feature_set()` to set the values
in the feature control register and replace `iommu_set_inv_tlb_timeout()`
with it.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20250307095822.2274-2-sarunkod@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Remove unused forward declaration.
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20250227162320.5805-7-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Large set of fixes for vector handling, especially in the
interactions between host and guest state.
This fixes a number of bugs affecting actual deployments, and
greatly simplifies the FP/SIMD/SVE handling. Thanks to Mark Rutland
for dealing with this thankless task.
- Fix an ugly race between vcpu and vgic creation/init, resulting in
unexpected behaviours
- Fix use of kernel VAs at EL2 when emulating timers with nVHE
- Small set of pKVM improvements and cleanups
x86:
- Fix broken SNP support with KVM module built-in, ensuring the PSP
module is initialized before KVM even when the module
infrastructure cannot be used to order initcalls
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being
emulated by KVM to fix a NULL pointer dereference
- Enter guest mode (L2) from KVM's perspective before initializing
the vCPU's nested NPT MMU so that the MMU is properly tagged for
L2, not L1
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as
the guest's value may be stale if a VM-Exit is handled in the
fastpath"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
x86/sev: Fix broken SNP support with KVM module built-in
KVM: SVM: Ensure PSP module is initialized if KVM module is built-in
crypto: ccp: Add external API interface for PSP module initialization
KVM: arm64: vgic: Hoist SGI/PPI alloc from vgic_init() to kvm_create_vgic()
KVM: arm64: timer: Drop warning on failed interrupt signalling
KVM: arm64: Fix alignment of kvm_hyp_memcache allocations
KVM: arm64: Convert timer offset VA when accessed in HYP code
KVM: arm64: Simplify warning in kvm_arch_vcpu_load_fp()
KVM: arm64: Eagerly switch ZCR_EL{1,2}
KVM: arm64: Mark some header functions as inline
KVM: arm64: Refactor exit handlers
KVM: arm64: Refactor CPTR trap deactivation
KVM: arm64: Remove VHE host restore of CPACR_EL1.SMEN
KVM: arm64: Remove VHE host restore of CPACR_EL1.ZEN
KVM: arm64: Remove host FPSIMD saving for non-protected KVM
KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state
KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop
KVM: nSVM: Enter guest mode before initializing nested NPT MMU
KVM: selftests: Add CPUID tests for Hyper-V features that need in-kernel APIC
KVM: selftests: Manage CPUID array in Hyper-V CPUID test's core helper
...
|
