| Age | Commit message (Collapse) | Author |
|---|
|
NORMAL (0x0) and IDLE (0x4) are really two different states. Hence you
cannot check for both using a bitmask, as that checks for IDLE only,
breaking operation for devices that are in NORMAL state.
Fix the wait function to report either state as ready.
Fixes: 6524d8eac258452e ("Input: st1232 - add IDLE state as ready condition")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210223090201.1430542-1-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The st1232 can switch from NORMAL to IDLE state after the configured
idle time (by default 8 s). If the st1232 is not reset during probe, it
might already be ready but in IDLE state. Since it does not enter NORMAL
state in this case, probe fails.
Fix the wait function to report the IDLE state as ready, too.
Fixes: f605be6a57b4 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210219110556.1858969-1-m.tretter@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.
If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution. However, the latter may
happen before the device is ready, leading to a probe failure:
st1232-ts 1-0055: Failed to read resolution: -6
Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.
On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.
Fixes: 3a54a215410b1650 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller. This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.
Optimize transfers by passing the wanted number of bytes.
Fixes: 3a54a215410b1650 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type. The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).
Fix this by subtracting 1.
Fixes: 3a54a215410b1650 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Hard-coding resolution for st1633 device was wrong. Some of LCDs like
YTS700TLBC-02-100C has assembled Sitronix st1633 touchcontroller too. But
the resolution is not 320x480 as was hard-coded.
Add new function which reads correct resolution directly from register.
Signed-off-by: Andrej Valek <andrej.valek@siemens.com>
Link: https://lore.kernel.org/r/20201103073949.12198-1-andrej.valek@siemens.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Switch the driver to the slotted variant of multitouch protocol (MT-B)
with in-kernel tracking of the contacts.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The receiving buffer is allocated separately from the main driver
data structure, and is naturally DMA-safe, so mark it as such when
building I2C transfer message.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
devm_input_allocate_device() already sets parent device for us.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The finger structure size is quite small and allocating it together with
the main driver structure will not increase likelyhood of allocation
failing, but reduces number of objects needing to be tracked by the
allocator and devm.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We should not be putting the chip into reset while interrupts are enabled
and ISR may be running. Fix this by installing a custom devm action and
powering off the device/resetting GPIO line from there. This ensures proper
ordering.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When I2C client is created with I2C_CLIENT_WAKE flag (which happens
either because we have "wakeup-source" device property or the flag
was passed in when creating an I2C client manually), I2C core will
take care of configuring interrupt as wakeup source on suspend.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Do not unconditionally configure the touchscreen as wakeup source but
rather rely on I2C core to do that when requested (either via
"wakeup-source" device property, or when creating a client with
I2C_CLIENT_WAKE flag).
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Avoid complex 2-variable loop when parsing touchscreen data to make the
code clearer.
Acked-by: Martin Kepplinger <martink@posteo.de>
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
For Sitronix st1633 multi-touch controller driver the coordinates reported
for multiple fingers were wrong, as it was always taking LSB of coordinates
from the first contact data.
Signed-off-by: Dixit Parmar <dixitparmar19@gmail.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Cc: stable@vger.kernel.org
Fixes: 351e0592bfea ("Input: st1232 - add support for st1633")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204561
Link: https://lore.kernel.org/r/1566209314-21767-1-git-send-email-dixitparmar19@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is required to specify generic touchscreen properties via DT.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is how userspace checks for touchscreen devices most reliably.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 1fa59bda21c7fa36 ("ARM: shmobile: Remove legacy board code for
Armadillo-800 EVA"), removed the last user of st1232_pdata and the
"st1232-ts" platform device. All remaining users use DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Rework dev_pm_qos_add_ancestor_request() so that device PM QoS type
is passed to it as the third argument and make it support the
DEV_PM_QOS_LATENCY_TOLERANCE device PM QoS type (in addition to
DEV_PM_QOS_RESUME_LATENCY).
That will allow the drivers of devices without latency tolerance
hardware support to use their ancestors having it as proxies for
their latency tolerance requirements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use the devm_* managed functions to allocate resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch enables DT support for the st1232 driver
which is primarily used on the sh7372 Mackerel board.
[dtor@mail.ru: chnaged to use CONFIG_OF and of_match_ptr]
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch converts the drivers in drivers/input/* to use the
module_i2c_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Make the st1232 driver use dev_pm_qos_add_ancestor_request() to
add a device PM QoS latency constraint for the controller it
depends on, so that the controller won't go into an overly deep
low-power state when the touchscreen has to be particularly
responsive (e.g. when the user moves his or her finger on it).
This change is based on a prototype patch from Guennadi Liakhovetski.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch introduces support for Sitronix ST1232 integrated capacitive
touchscreen with LCD module. The touchscreen is multitouch capable and
can report coordinates of up to two contact points.
Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
