| Age | Commit message (Collapse) | Author |
|---|
|
I got an idea the i2c-designware should not need duplicated state
machines for the interrupt and polling modes. The IP is practically the
same and state transitions happens in response to the events that can be
observed from the DW_IC_RAW_INTR_STAT register. Either by interrupts or
by polling.
Another reasons are the interrupt mode is the most tested, has handling
for special cases as well as transmit abort handling and those are
missing from two polling mode quirks.
Patch implements a generic polling mode by using existing code for
interrupt mode. This is done by moving event handling from the
i2c_dw_isr() into a new i2c_dw_process_transfer() that will be called
both from the i2c_dw_isr() and a polling loop.
Polling loop is implemented in a new i2c_dw_wait_transfer() that is
shared between both modes. In interrupt mode it waits for the completion
object as before. In polling mode both completion object and
DW_IC_RAW_INTR_STAT are polled to determine completed transfer and state
transitions.
Loop tries to save power by sleeping "stetson guessed" range between
3 and 25 µS which falls between 10 cycles of High-speed mode 3.4 Mb/s
and Fast mode 400 kHz. With it the CPU usage was reduced under heavy
Fast mode I2C transfer without much increase in total transfer time but
otherwise no more effort has been put to optimize this.
I decided to convert the txgbe_i2c_dw_xfer_quirk() straight to generic
polling mode code in this patch. It doesn't have HW dependent quirks
like the amd_i2c_dw_xfer_quirk() does have and without users this patch
is needless.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Code is more logically arranged when i2c_dw_read_clear_intrbits() and
i2c_dw_isr() are located before i2c_dw_xfer().
Real reason for this is to prepare for more shared code between
interrupt and polling mode code.
While at it, remove one extra space and refer to the
i2c_dw_init_master() in two comment sections.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert access to DW_IC_INTR_MASK register using the existing
__i2c_dw_write_intr_mask() and a __i2c_dw_read_intr_mask() introduced
here. Motivation to this is to prepare for generic polling mode code
where polling mode will use a SW mask instead of DW_IC_INTR_MASK.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
I was testing the polling mode txgbe_i2c_dw_xfer_quirk() on a HW where
the i2c-designware has interrupt connected and shared with other device.
I noticed there is a bogus interrupt for each transfer.
Reason for this that both polling mode functions call the
i2c_dw_xfer_init() which enable interrupts then followed by immediate
disable by the same polling mode functions. This is enough to trigger
TX_EMPTY interrupt.
Fix this by introducing a __i2c_dw_write_intr_mask() helper that unmasks
interrupts conditionally and use it in i2c_dw_xfer_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Currently initialization flow in i2c_dw_probe_master() skips a few steps
and has code duplication for polling mode implementation.
Simplify this by adding a new ACCESS_POLLING flag that is set for those
two platforms that currently use polling mode and use it to skip
interrupt handler setup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
|
|
Currently if the SoC needs pinctrl to switch the SCL and SDA from the I2C
function to GPIO function, the recovery won't work.
scl-gpio = <>;
sda-gpio = <>;
Are not enough for some SoCs to have a working recovery.
Some need:
scl-gpio = <>;
sda-gpio = <>;
pinctrl-names = "default", "recovery";
pinctrl-0 = <&i2c_pins_hw>;
pinctrl-1 = <&i2c_pins_gpio>;
The driver was not filling rinfo->pinctrl with the device node
pinctrl data which is needed by generic recovery code.
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit 0daede80f870 ("i2c: designware: Convert driver to using regmap API")
changes the logic to validate the whole 32-bit return value of
DW_IC_DATA_CMD register instead of 8-bit LSB without reason.
Later, commit f53f15ba5a85 ("i2c: designware: Get right data length"),
introduced partial fix but not enough because the "tmp > 0" still test
tmp as 32-bit value and is wrong in case the IC_DATA_CMD[11] is set.
Revert the logic to just before commit 0daede80f870
("i2c: designware: Convert driver to using regmap API").
Fixes: f53f15ba5a85 ("i2c: designware: Get right data length")
Fixes: 0daede80f870 ("i2c: designware: Convert driver to using regmap API")
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-2-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
with SFP.
Introduce the property "wx,i2c-snps-model" to match device data for Wangxun
in software node case. Since IO resource was mapped on the ethernet driver,
add a model quirk to get regmap from parent device.
The exists IP limitations are dealt as workarounds:
- IP does not support interrupt mode, it works on polling mode.
- Additionally set FIFO depth address the chip issue.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
regmap_read() API signature expects the caller to send "unsigned int"
type to return back the read value, but there are some occurrences of 'u32'
across i2c-designware-* files.
Change them to match the regmap_read() signature.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
On some AMD platforms, based on the new designware datasheet,
BIOS sets the BIT(11) within the IC_CON register to advertise
the "bus clear feature capability".
AMD/Designware datasheet says:
Bit(11) BUS_CLEAR_FEATURE_CTRL. Read-write,Volatile. Reset: 0.
Description: In Master mode:
- 1'b1: Bus Clear Feature is enabled.
- 1'b0: Bus Clear Feature is Disabled.
In Slave mode, this register bit is not applicable.
On AMD platform designs:
1. BIOS programs the BUS_CLEAR_FEATURE_CTRL and enables the detection
of SCL/SDA stuck low.
2. Whenever the stuck low is detected, the SMU FW shall do the bus
recovery procedure.
Currently, the way in which the "master_cfg" is built in the driver, it
overrides the BUS_CLEAR_FEATURE_CTRL advertised by BIOS and the SMU FW
cannot initiate the bus recovery if the stuck low is detected.
Hence add a check in i2c_dw_probe_master() that if the BIOS
advertises the bus clear feature, let driver not ignore it and
adapt accordingly.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit 90312351fd1e ("i2c: designware: MASTER mode as separated driver")
introduced disable_int pointer but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable_int() and scope is inside the same kernel module.
Since i2c_dw_disable_int() is just masking interrupts and the direct
DW_IC_INTR_MASK register write looks more clear in the code use that and
remove it from common code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In my opinion a few lines of spurious interrupt detection code can be
moved to the actual master interrupt handling function i2c_dw_isr()
without hurting readability.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It is kind of needless to print interrupt status when code immediately
after that finds interrupt was not originating from this device.
Therefore move it after spurious interrupt detection.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Do not return with interrupt handled if host controller is off and thus
interrupt is originating from other device or is spurious.
Add a check to detect when controller is runtime suspended or
transitioning/reset. In latter case all raw interrupt status register
bits may read one. In both cases return IRQ_NONE to indicate interrupt
was not from this device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Define software status flags with a BIT() macro. While at it remove
STATUS_IDLE and replace its use with zero initialization and status
flags clearing with a mask.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit c7b79a752871 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI
IDs") caused a regression on certain Gigabyte motherboards for Intel
Alder Lake-S where system crashes to NULL pointer dereference in
i2c_dw_xfer_msg() when system resumes from S3 sleep state ("deep").
I was able to debug the issue on Gigabyte Z690 AORUS ELITE and made
following notes:
- Issue happens when resuming from S3 but not when resuming from
"s2idle"
- PCI device 00:15.0 == i2c_designware.0 is already in D0 state when
system enters into pci_pm_resume_noirq() while all other i2c_designware
PCI devices are in D3. Devices were runtime suspended and in D3 prior
entering into suspend
- Interrupt comes after pci_pm_resume_noirq() when device interrupts are
re-enabled
- According to register dump the interrupt really comes from the
i2c_designware.0. Controller is enabled, I2C target address register
points to a one detectable I2C device address 0x60 and the
DW_IC_RAW_INTR_STAT register START_DET, STOP_DET, ACTIVITY and
TX_EMPTY bits are set indicating completed I2C transaction.
My guess is that the firmware uses this controller to communicate with
an on-board I2C device during resume but does not disable the controller
before giving control to an operating system.
I was told the UEFI update fixes this but never the less it revealed the
driver is not ready to handle TX_EMPTY (or RX_FULL) interrupt when device
is supposed to be idle and state variables are not set (especially the
dev->msgs pointer which may point to NULL or stale old data).
Introduce a new software status flag STATUS_ACTIVE indicating when the
controller is active in driver point of view. Now treat all interrupts
that occur when is not set as unexpected and mask all interrupts from
the controller.
Fixes: c7b79a752871 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs")
Reported-by: Samuel Clark <slc2015@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215907
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use the i2c_mark_adapter_suspended/resumed() i2c-core helpers and rely
on the i2c-core's suspended checking instead of using DIY code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
All accesses to controller's registers should be protected on
probe, disable and xfer paths. This is needed for i2c bus controllers
that are shared with but not controller by kernel.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Intel Keem Bay platform supports multi-master operations over same i2c
bus using Synopsys i2c DesignWare IP. When multi-masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c DesignWare driver does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for the following conditions:
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/i2c/busses/i2c-designware-master.c:176: warning: expecting prototype for i2c_dw_init(). Prototype was for i2c_dw_init_master() instead
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers for Silicon Labs CP2615 and the HiSilicon I2C unit
- bigger refactoring for the MPC driver
- support for full software nodes - no need to work around with only
properties anymore
- we now have 'devm_i2c_add_adapter', too
- sub-system wide fixes for the RPM refcounting problem which often
caused a leak when an error was encountered during probe
- the rest is usual driver updates and improvements
* 'i2c/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: mediatek: Use scl_int_delay_ns to compensate clock-stretching
i2c: mediatek: Fix wrong dma sync flag
i2c: mediatek: Fix send master code at more than 1MHz
i2c: sh7760: fix IRQ error path
i2c: i801: Add support for Intel Alder Lake PCH-M
i2c: core: Fix spacing error by checkpatch
i2c: s3c2410: simplify getting of_device_id match data
i2c: nomadik: Fix space errors
i2c: iop3xx: Fix coding style issues
i2c: amd8111: Fix coding style issues
i2c: mpc: Drop duplicate message from devm_platform_ioremap_resource()
i2c: mpc: Use device_get_match_data() helper
i2c: mpc: Remove CONFIG_PM_SLEEP ifdeffery
i2c: mpc: Use devm_clk_get_optional()
i2c: mpc: Update license and copyright
i2c: mpc: Interrupt driven transfer
i2c: sh7760: add IRQ check
i2c: rcar: add IRQ check
i2c: mlxbf: add IRQ check
i2c: jz4780: add IRQ check
...
|
|
Use generic i2c_freq_mode_string() helper to print chosen bus speed.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since we have generic definitions for bus frequencies, let's use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The Latest AMD NAVI GPU card has an integrated Type-C controller and
Designware I2C with PCI Interface. The PD controller for USB Type-C can
be accessed over I2C. The client driver is part of the USB Type-C UCSI
driver.
Also, there exists a couple of notable IP limitations that are dealt as
workarounds:
- I2C transaction work on a polling mode as IP does not generate
interrupt.
- I2C read command sent twice to address the IP issues.
- AMD NAVI GPU based products are already in the commercial market,
hence some of the I2C parameters are statically programmed as they
can not be part of the ACPI table.
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Co-developed-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When hardware doesn't support High Speed Mode, we forget bus_freq_hz
timing adjustment. This makes the timings and real registers being
unsynchronized. Adjust bus_freq_hz when refuse high speed mode set.
Fixes: b6e67145f149 ("i2c: designware: Enable high speed mode")
Reported-by: "Song Bao Hua (Barry Song)" <song.bao.hua@hisilicon.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
IC_DATA_CMD[11] indicates the first data byte received after the address
phase for receive transfer in Master receiver or Slave receiver mode,
this bit was set in some transfer flow. IC_DATA_CMD[7:0] contains the
data to be transmitted or received on the I2C bus, so we should use the
lower 8 bits to get the real data length.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Seeing the DW I2C driver is using flags-based accessors with two
conditional clauses it would be better to replace them with the regmap
API IO methods and to initialize the regmap object with read/write
callbacks specific to the controller registers map implementation. This
will be also handy for the drivers with non-standard registers mapping
(like an embedded into the Baikal-T1 System Controller DW I2C block, which
glue-driver is a part of this series).
As before the driver tries to detect the mapping setup at probe stage and
creates a regmap object accordingly, which will be used by the rest of the
code to correctly access the controller registers. In two places it was
appropriate to convert the hand-written read-modify-write and
read-poll-loop design patterns to the corresponding regmap API
ready-to-use methods.
Note the regmap IO methods return value is checked only at the probe
stage. The rest of the code won't do this because basically we have
MMIO-based regmap so non of the read/write methods can fail (this also
won't be needed for the Baikal-T1-specific I2C controller).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: fix type of 'rx_valid' and remove outdated kdoc var description]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
As a preparatory patch to support slave mode for PCI enumerated devices rename
i2c_dw_probe() to i2c_dw_probe_master() and split common i2c_dw_probe() as
inline helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Move configuration routines to respective modules, i.e. master and slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for High Speed Mode too.
The value for the parameters tSYMBOL and tLOW is taken from DesignWare
DW_apb_i2c Databook v2.01a, section 3.15.4.6. The calculation should
assume higher bus load since it gives slower timing parameter.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for Fast Mode Plus.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix spelling typos in the comments with help of `codespell`.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The problem with detecting the FIFO depth in the platform driver
is that in order to implement this we have to access the controller
IC_COMP_PARAM_1 register. Currently it's done before the
i2c_dw_set_reg_access() method execution, which is errors prone since
the method determines the registers endianness and access mode and we
can't use dw_readl/dw_writel accessors before this information is
retrieved. We also can't move the i2c_dw_set_reg_access() function
invocation to after the master/slave probe functions call (when endianness
and access mode are determined), since the FIFO depth information is used
by them for initializations. So in order to fix the problem we have no
choice but to move the FIFO size detection methods to the common code and
call it at the probe stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
drivers/i2c/busses/i2c-designware-master.c: In function ‘i2c_dw_init_recovery_info’:
drivers/i2c/busses/i2c-designware-master.c:658:6: warning: unused variable ‘r’ [-Wunused-variable]
int r;
^
Fixes: 33eb09a02e8d ("i2c: designware: make use of devm_gpiod_get_optional")
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is a semantical change: if devm_gpiod_get_optional returns -ENOSYS
this is passed as error to the caller. This effectively reverts commit
d1fa74520dcd ("i2c: designware: Consider SCL GPIO optional") which
shouldn't be necessary any more since gpiod_get_optional doesn't return
-ENOSYS any more with GPIOLIB=n.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There are two problems with dev_err() here. One: It is not ratelimited.
Two: We don't see which driver tried to transfer something with a
suspended adapter. Switch to dev_WARN_ONCE to fix both issues. Drawback
is that we don't see if multiple drivers are trying to transfer while
suspended. They need to be discovered one after the other now. This is
better than a high CPU load because a really broken driver might try to
resend endlessly.
Link: https://bugs.archlinux.org/task/62391
Fixes: 275154155538 ("i2c: designware: Do not allow i2c_dw_xfer() calls while suspended")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: skidnik <skidnik@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: skidnik <skidnik@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C
and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI
methods (power on / off methods) of various devices.
This leads to suspend/resume ordering problems where a device may be
resumed and get its _PS0 method executed before the I2C controller is
resumed. On Cherry Trail this leads to errors like these:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
But on Bay Trail this caused I2C reads to seem to succeed, but they end
up returning wrong data, which ends up getting written back by the typical
read-modify-write cycle done to turn on various power-resources.
Debugging the problems caused by this silent data corruption is quite
nasty. This commit adds a check which disallows i2c_dw_xfer() calls to
happen until the controller's resume method has completed.
Which turns the silent data corruption into getting these errors in
dmesg instead:
i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR
Which is much better.
Note the above errors are an example of issues which this patch will
help to debug, the actual fix requires fixing the suspend order and
this has been fixed by a different commit.
Note the setting / clearing of the suspended flag in the suspend / resume
methods is NOT protected by i2c_lock_bus(). This is intentional as these
methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd
i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would
deadlock. This means that there is a theoretical race between a non runtime
suspend and the suspended check in i2c_dw_xfer(), this is not a problem
since normally we should not hit the race and this check is primarily a
debugging tool so hitting the check if there are suspend/resume ordering
problems does not need to be 100% reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This is the 4.19-rc7 release
|
|
On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller. The GPU
is a PCI device and PCI devices are powered-on at the resume_noirq resume
phase.
Since the GPU power-resources need the I2C controller, recent acpi_lpss.c
changes now also power-up the LPSS I2C controllers on BYT and CHT devices
in the resume_noirq resume phase. But during this phase the IRQ of the
controller is disabled leading to these errors:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
This commit makes the i2c-designware controller set the IRQF_NO_SUSPEND
flag when requesting the interrupt on BYT and CHT devices, so that the IRQ
is left enabled during the noirq phase, fixing this.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f277274b ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f277274b ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit a3d411fb38c0 ("i2c: designware: Disable pm for PMIC i2c-bus even if
there is no _SEM method"), always set the pm_disabled flag on the I2C7
controller, even if its bus was not shared with the PUNIT.
This was a workaround for various suspend/resume issues, after the
following 2 commits this workaround is no longer necessary:
Commit 541527728341 ("PM: i2c-designware-platdrv: Suspend/resume at the
late/early stages")
Commit e6ce0ce34f65 ("ACPI / LPSS: Add device link for CHT SD card
dependency on I2C")
Therefor this commit removes this workaround.
After this commit the pm_disabled flag is only used to indicate that the
bus is shared with the PUNIT and after other recent changes we no longer
call dev_pm_syscore_device(dev, true), so we are no longer actually
disabling (non-runtime) pm, so this commit also renames the flag to
shared_with_punit to better reflect what it is for.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
PSAT |= 0x03
Local0 = PSAT /* \_SB_.I2C5.PSAT */
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Trivial added debug print for dev->clk_freq doesn't necessarily tell the
actual bus speed or mode the controller is operating. For instance it
may indicate 1 MHz Fast Mode Plus or 3.4 MHz High Speed but driver ends up
using 400 kHz Fast Mode due missing timing parameters or missing support
from HW.
Add a debug print that prints the bus speed based on the validated speed
that gets programmed into a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Mixed timing parameter validation, calculation and their debug prints
with HW initialization in i2c_dw_init_master() and i2c_dw_init_slave()
as been bothering me some time.
It makes function a little bit unclear to follow, doesn't show what steps
are needed to do only once during probe and what are needed whenever HW
needs to be reinitialized. Also those debug prints show information that
doesn't change runtime and thus are also needlessly printed multiple times
whenever HW is reinitialized.
Thus let the i2c_dw_init_master() and i2c_dw_init_slave() to do only HW
initialization and move out one time parameter setting and debug prints
to separate functions which are called only during probe.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
