| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Fix the following warning by adding a missing break:
drivers/gpio/gpio-eic-sprd.c: In function ‘sprd_eic_irq_set_type’:
drivers/gpio/gpio-eic-sprd.c:403:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (flow_type) {
^~~~~~
drivers/gpio/gpio-eic-sprd.c:435:2: note: here
default:
^~~~~~~
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Zynq GPIO driver currently implements runtime PM by:
- Enabling runtime PM support in ->probe() and letting the runtime PM
reference counter drop to zero at the end of ->probe().
- Increasing the runtime PM reference counter in ->request() and
decreasing it in ->free().
However, the latter is not sufficient: when a GPIO is used as an
interrupt, ->request() and ->free() are not called. Due to this, the
runtime PM counter remains to zero when the only GPIOs in use are used
as interrupts, causing them to simply not work.
To address this problem, this commit implement the
->irq_request_resources() and ->irq_release_resources() hooks,
ensuring that the runtime PM counter is properly
incremented/decremented. Since we override the default hooks, we keep
the existing behavior by making sure they call gpiochip_reqres_irq() /
gpiochip_relres_irq() respectively.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds a minimal implementation of the ->set_config() hook,
with support for the PIN_CONFIG_BIAS_PULL_UP and
PIN_CONFIG_BIAS_PULL_DOWN configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds support for configuring the pull-up and pull-down
resistors available in some GPIO controllers. While configuring
pull-up/pull-down is already possible through the pinctrl subsystem,
some GPIO controllers, especially simple ones such as GPIO expanders
on I2C, don't have any pinmuxing capability and therefore do not use
the pinctrl subsystem.
This commit implements the GPIO_PULL_UP and GPIO_PULL_DOWN flags,
which can be used from the Device Tree, to enable a pull-up or
pull-down resistor on a given GPIO.
The flag is simply propagated all the way to the core GPIO subsystem,
where it is used to call the gpio_chip ->set_config callback with the
appropriate existing PIN_CONFIG_BIAS_* values.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As suggested by Linus Walleij, let's use the new gpio_set_config()
helper in gpiod_set_debounce() and gpiod_set_transitory().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit simply renames gpio_set_drive_single_ended() to
gpio_set_config(), as the function is not specific to setting the GPIO
drive type, and will be used for other purposes in followup commits.
In addition, it moves the function above gpiod_direction_input(), as
it will be used from gpiod_direction_input().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Interupts were generated using GPIN interrupts of
ADP5588. These interrupts have two important limitations:
1. Interrupts can only be generated for either rising or
falling edges but not both.
2. Interrupts are reasserted as long as the interrupt condition
persists (i.e. high or low level on that GPIN). This generates
lots of interrupts unless the event is very short.
To overcome this, ADP5588 provides an event system which queues
up to 10 events in a buffer. GPIN events are queued whenever the
GPIN is asserted or deasserted. This makes it possible to support
generating GPIN interrupts for both edges and to generate only one
interrupt per state change.
Thus it is possible to chain the gpio-keys driver for some GPIOs.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make platform data optional and add DT id table.
Switch to dynamically mapped GPIOs and IRQs if not provided
via platform data.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's not necessary to remove gpio_chip which added with
devm_gpiochip_add_data().
Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a driver for Gateworks PLD GPIO, that exist in
two instances on the Gateworks Cambria GW2358-4 router
platform at least.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
New quirk enforces search for GPIO based on its type,
i.e. iterate over GpioIo resources only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
|
|
In some cases the indentation is inconsistent. Fix it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
|
|
There is no need to check for non-zero pending since for_each_set_bit() does it
on the first iteration.
While here, drop redundant assignment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The type of to_reg() is unsigned int while it might return
a negative error code. Callers are also expecting a signed type.
For sake of type consistency replace unsigned int with plain int.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
|
|
This fixes the kernel complains:
gpio gpiochip1: (1e000600.gpio-bank1): detected irqchip that is shared
with multiple gpiochips: please fix the driver.
gpio gpiochip2: (1e000600.gpio-bank2): detected irqchip that is shared
with multiple gpiochips: please fix the driver.
Fixes: 4ba9c3afda41 ("gpio: mt7621: Add a driver for MT7621")
Cc: stable@vger.kernel.org
Signed-off-by: René van Dorst <opensource@vdorst.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Tested-by: Greg Ungerer <gerg@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On SoC reset all GPIO interrupts are disable. However, if kexec is
used to boot into a new kernel, the SoC does not experience a
reset. Hence GPIO interrupts can be left enabled from the previous
kernel. It is then possible for the interrupt to fire before an
interrupt handler is registered, resulting in the kernel complaining
of an "unexpected IRQ trap", the interrupt is never cleared, and so
fires again, resulting in an interrupt storm.
Disable all GPIO interrupts before registering the GPIO IRQ chip.
Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The checker complains during build
gpiolib-acpi.c:45: warning: Function parameter or member 'irq_requested' not described in 'acpi_gpio_event'
because the typo in the field description.
Fix the name to have documentation up-to-date.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some TQ-Systems ComExpress modules contain an IO controller with 8
GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing '*' char to the start of the comment lines.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SPI chip selects were not properly inspected due to
a logic inversion. This made SPI GPIOs not work.
Cc: Jan Kotas <jank@cadence.com>
Reported-by: Jan Kotas <jank@cadence.com>
Tested-by: Jan Kotas <jank@cadence.com>
Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
This adds the two new functions gpiochip_irq_domain_activate and
gpiochip_irq_domain_deactivate that can be used as the activate and
deactivate functions in the struct irq_domain_ops. This is for
situations where only gpiochip_{lock,unlock}_as_irq needs to be called.
SPMI and SSBI GPIO are two users that will initially use these
functions.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The altr_a10sr_gpio_direction_output should set proper output level
based on the value argument.
Fixes: 26a48c4cc2f1 ("gpio: altera-a10sr: Add A10 System Resource Chip GPIO support.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When setting async EIC as IRQ_TYPE_EDGE_BOTH type, we missed to set the
SPRD_EIC_ASYNC_INTMODE register to 0, which means detecting edge signals.
Thus this patch fixes the issue.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Neo Hou <neo.hou@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Since differnt type EICs have its own data register to read, thus fix the
incorrect data register.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Neo Hou <neo.hou@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Nested interrupts run inside the calling thread's context and the top
half handler is never called which means that we never read the
timestamp.
This issue came up when trying to read line events from a gpiochip
using regmap_irq_chip for interrupts.
Fix it by reading the timestamp from the irq thread function if it's
still 0 by the time the second handler is called.
Fixes: d58f2bf261fd ("gpio: Timestamp events in hardirq handler")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When multiple instances of pcf857x chips are present, a fix up
message [1] is printed during the probe of the 2nd and later
instances.
The issue is that the driver is using the same irq_chip data
structure between multiple instances.
Fix this by allocating the irq_chip data structure per instance.
[1] fix up message addressed by this patch
[ 1.212100] gpio gpiochip9: (pcf8575): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Basic implementation of driver is used to support Fintek
F81804 & F81966 gpios with custom register set.
Signed-off-by: Steffen Kothe <steffen.kothe.gc1993@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
R-Car GPIO controller provides two interfaces to set GPIO line output
signal state, and for a particular GPIO line the selected interface is
determined by OUTDTSEL bit value.
At the moment the driver supports only one of two interfaces, namely
OUTDT General Output Register is used to control the output signal.
While this selection is the default one on reset, it is not explicitly
configured on probe, thus it might be possible that kernel and userspace
consumers of a GPIO won't be able to set the wanted GPIO output signal.
Below is a simple test case to reproduce the described problem and
verify this fix in the kernel on H3 ULCB by setting non-default OUTDTSEL
configuration from a bootloader:
u-boot > mw.l 0xe6055440 0x3000 1
...
userspace > echo default-on > /sys/devices/platform/leds/leds/led5/trigger
userspace > echo default-on > /sys/devices/platform/leds/leds/led6/trigger
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Like the Spreadtrum EIC driver[1], this driver needs to emulate edge
triggered interrupts to support the generic gpio-keys driver.
[1]: https://www.spinics.net/lists/kernel/msg2764576.html
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch implements level-triggered IRQs in the Hollywood GPIO driver.
Edge triggered interrupts are not supported in this GPIO controller, so
I moved their emulation into a separate patch.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a system has two PCA953x GPIO expanders, the kernel complains with:
gpio gpiochip2: (0-0021): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Indeed, there is a single instance of "struct irq_chip" that gets
re-used for both PCA953x instance. This commit moves the "struct
irq_chip" to be part of the "struct pca953x_chip", so that we have one
"struct irq_chip" per PCA953X instance.
As part of this, the name of the irq_chip is also made different on a
per-instance basis, now using the dev_name() of the I2C device. This
changes what is visible in /proc/interrupts.
Before:
47: 0 0 pca953x 10 Edge e0100000.sdhci cd
48: 0 0 pca953x 6 Edge e0101000.sdhci cd
After:
47: 0 0 0-0020 10 Edge e0100000.sdhci cd
48: 2 0 0-0020 6 Edge e0101000.sdhci cd
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current design of pca953x_irq_setup() is:
if (all conditions to support IRQ are met) {
lots of code to support IRQs, which goes to a serious indentation
level.
}
return 0;
It makes more sense to handle this like this:
if (!all conditions to support IRQ are met)
return 0;
handle IRQ support
This commit does just this change, reducing by one tab the indentation
level of the IRQ setup code. Thanks to this reduced indentation level,
we are less restricted by the 80-column limit, and we can have more
function arguments on the same line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Spreadtrum PMIC interrupt controller has no registers to set irq
trigger type, since it is always high level trigger. That means the
PMIC EIC controller as a child device of PMIC INTC does not need to
set the trigger type, so remove it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Set proper output level base on the argument of direction_output.
Also remove sama5d2_piobu_set_direction() as there is only one caller
now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes the following sparse warning:
drivers/gpio/gpio-pca953x.c:292:28: warning:
symbol 'pca953x_i2c_regmap' was not declared. Should it be static?
Fixes: 49427232764d ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
__acpi_gpio_update_gpiod_flags purpose is to make the gpiod_flags used
when requesting a GPIO match the restrictions from the ACPI resource,
as stored in acpi_gpio_info.flags.
But acpi_gpio_info.flags only contains direction info, and the
requester may have passed in special non-direction flags like
GPIOD_FLAGS_BIT_NONEXCLUSIVE, which we currently clobber.
This commit modifies __acpi_gpio_update_gpiod_flags to preserve these
special flags, so that a requested of an ACPI GPIO can e.g. pass
GPIOD_FLAGS_BIT_NONEXCLUSIV and have it work as intended.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
struct gpio_chip documentation recommends to always implement this
callback function.
A more concrete motivation is to be able (in combination with
GPIOD_ASIS) to detect whether the bootloader has changed the state of a
GPIO signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
acpi_gpiochip_alloc_event only continues allocating an event and adding
it to the list if gpiochip_request_own_desc does not return an error.
So events with an error desc are never placed on the events list and this
check is really not necessary.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
|
|
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
|
